|
| 1 | Civil work. |
| 2 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like , including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed lead upto 50 meters . All kinds of soil |
| 3 | Earth work excavation by mechaniclal means(Hydraulic Excavator) including disposal of excavated earth upto 50 m lead (All kinds of soil). |
| 4 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. ( All kinds of soil :) |
| 5 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as10 sqm on plan including disposal of excavated earth, lead upto50meterand lift upto 1.5m, as directed by Engineer-in-Charge. All kinds of soil : |
| 6 | Extra lead beyonf 50 m upto 1 Km |
| 7 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked material (All kinds of soil) |
| 8 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating on deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 9 | Supplying and filling in plinth with sand under floors including, watering, ramming, consolidating and dressing complete from surface drains and disposal including all carriages |
| 10 | Supplying stacking and laying of good earth at site including spreading, levelling watering in layers and consolidated with hand rolling including all carriages. |
| 11 | P/L of stone soling of required sizes , compacting , watering and ramming, complete including all carriages. |
| 12 | Providing, fitting, spreading of GSB filling (Nallah Muck ) from approved source including watering , compacting and rolling in 150 mm layers complete including all carriages. |
| 13 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering including all carriages. |
| 14 | (A) 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size). |
| 15 | (A) 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size). |
| 16 | (B) 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size). |
| 17 | (C) 1:4:8 (1 cement: 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 18 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. 1:1½:3 (1 cement: 1½ coarse sand: 3 graded stone aggregate 20 mm nominal size).including all carriage. |
| 19 | (upto plinth level) |
| 20 | (Above plinth level) |
| 21 | Centering and shuttering including strutting, proppingetc. and removal of form for any locations such as |
| 22 | suspended floors, roofs, landing balconies, shelves,lentils ,beams, pillars stair etc |
| 23 | Foundation,footings,basis of columns etc. |
| 24 | Walls (any thickness) including attached pilasters, buttresses, plinth andstring courses etc. |
| 25 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-450 or more. |
| 26 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : |
| 27 | (A)Cement mortar 1:4 ( 1 cement : 4 coarse sand) incl cost and carriage of materials involved complete. |
| 28 | (B)Cement mortar 1:6 ( 1 cement : 6 coarse sand)incl cost and carriage of materials involved complete. |
| 29 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 30 | Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : |
| 31 | Cement mortar 1:3 ( 1 cement : 3 coarse sand) |
| 32 | Cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 33 | Extra for half Brick masonry in superstructure above plinth level upto floor V level. |
| 34 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:3 (1 cement : 3 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels (18mm thick) (Granite of any colour or shade as approved by Engineer-incharge). |
| 35 | Area of Slab upto 0.5 sqm. |
| 36 | Area of Slab over 0.5 sqm. |
| 37 | Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates, ceiling joists frame work and or likecomponents.(First class Budloo wood). |
| 38 | Providing wood work in frames of doors, windows, clerestory windows andother frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): |
| 39 | (1st class deodar wood) |
| 40 | (2nd class deodar wood) |
| 41 | (1st class Kail wood) |
| 42 | (Imported wood (KD)) |
| 43 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters (35mm) (With ISI marked M.S. pressed butt hinges brightfinished of required size with necessary screws). |
| 44 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws size) 35 mm thick |
| 45 | Providing and fixing wire gauze shutters using galvanizedM.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge (35 mm thk). |
| 46 | First class deodar wood. |
| 47 | 2nd class deodar wood. |
| 48 | First class kail wood. |
| 49 | KD(Imported wood.) |
| 50 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 3.5 mm to 4 mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.35 mm |
| 51 | First class deodar wood. |
| 52 | 2nd class deodar wood. |
| 53 | First class kail wood. |
| 54 | KD(Imported wood.) |
| 55 | Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).35 mm |
| 56 | First class deodar wood. |
| 57 | 2nd class deodar wood. |
| 58 | First class kail wood. |
| 59 | KD(Imported wood.) |
| 60 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone |
| 61 | Providing wood work in frames of falseceiling.partitionong etc.sawn and fixed in position |
| 62 | (Budloo wood) |
| 63 | Imported wood (KD) |
| 64 | Poplar wood |
| 65 | Providing and fixing ISI marked aluminum butt hinges ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 66 | (a)125x75x4 mm |
| 67 | (b)125x63x4 mm |
| 68 | ©100x75x4 mm |
| 69 | (d) 100x63x4 mm |
| 70 | (e)75x63x4 mm |
| 71 | (f)50x40x2.5 mm |
| 72 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 73 | (a) 300x10 mm |
| 74 | (b)250x10 mm |
| 75 | ©200x10 mm |
| 76 | (d)150x10 mm |
| 77 | (e)100x10 mm |
| 78 | (P/F of ISI marked M.S pressed butt Hinges |
| 79 | 125*65*2.12 mm |
| 80 | 100*58*1.90 mm |
| 81 | 75*60.*3.10 mm |
| 82 | 50*37*1.5 mm |
| 83 | (P/F of M.S Hinges 125mm welded heavy) |
| 84 | (P/F of M.S Hinges for gates) |
| 85 | 100mm |
| 86 | 150mm |
| 87 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. |
| 88 | (a) 125 mm |
| 89 | (b) 100 mm |
| 90 | ©75 mm |
| 91 | (d) 200 mm |
| 92 | (e)150 mm |
| 93 | (f)175 mm |
| 94 | P/F of ornamental Handle of approved quality: |
| 95 | 75 mm |
| 96 | 100 mm |
| 97 | 150 mm |
| 98 | 200 mm |
| 99 | P/F of Aldrop of approved quality |
| 100 | 1'0'' |
| 101 | P/F Powder coated Aluminum handles of approvedquality |
| 102 | 75 mm |
| 103 | 100 mm |
| 104 | 150 mm |
| 105 | 200 mm |
| 106 | P/F of Piano Hinges including cost of screws complete. |
| 107 | P/F of stainless steel telescopic drawer channels(450 mm) |
| 108 | P/F of stainless steel telescopic drawer channels(300 mm) |
| 109 | P/F of Hydraulic door spring including all costs. |
| 110 | P/F of Hydraulic doorcloser |
| 111 | Providing and fixing wooden moulded cornice beading triangular shape to the junction/corner/edges of paneling etc. with iron nails screws, plugs and priming coat on unexposed surface etc. complete. (First class kail wood). |
| 112 | 50*50 |
| 113 | 40*40 |
| 114 | 25*25 |
| 115 | P/f of ornamental wooden cornice imported (32*32) |
| 116 | P/f of pvc cornice |
| 117 | 50*50 |
| 118 | 40*40 |
| 119 | 25*25 |
| 120 | Providing and fixing deoder wood lipping/moulded beading of size 35x5mm fixed with wooden adhesive of approved quality and screws/nails on the edges of the pre laminated particle board as per directions of the engineer-in-charge. |
| 121 | P/F 40mm * 6 mm ply lipping. |
| 122 | Providing and fixing bright finished 100mm mortice lock with 6 levers without pair of handles for aluminum doors of approved quality with necessary screws etc. complete as per direction of Engineer-in-charge. |
| 123 | Providing and fixing magnetic catcher of approved quality in cupboard/wardrobe shutters including fixing with necessaryscrews etc. complete. (Godrej/link) |
| 124 | Structural steel work welded in built up sections, gratings, guard bar,stair case,gates, ladder, railing, brackets, and similar work including tubular works. Including cutting, hoisting, fixing in position welded and applying a priming coat of approved steel primer all complete. |
| 125 | Structural steel work welded in built up sections, trusses. Framed work. Including cutting, hoisting, fixing in position welded and applying a priming coat of approved steel primer all complete.(Welded) |
| 126 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.(completejob) |
| 127 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc.complete.(50 mmthick) |
| 128 | Kota stone slab flooring 25 mm thick over 20mm (average) thick 1:4 cement mortar base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing. |
| 129 | Pre-polished Kota stone slab flooring 25 mm thick over 20mm (average) thick 1:4 cement mortar base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete. |
| 130 | Providing and fixing Ist quality ceramic glazed wall tiles of approved make, in all colours, shades(of 7-8 mm thick of different sizes) as approved by Engineer- in-Charge, in walls, skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 131 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown |
| 132 | Providing and laying vitrified floor tiles with water absorption less than 0.08% of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement:4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.(10 mm) ( Size of tile 600x600 mm). |
| 133 | Providing and laying Full body vitrified floor tiles with water absorption less than 0.08% of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement:4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.(10 mm) ( Size of tile 600x600 mm). |
| 134 | Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 135 | 0.63 mm thick with zinc coating not less than 275 gram/m2 |
| 136 | 0.50 mm thick with zinc coating not less than 275 gram/m2 |
| 137 | P/F of color coated of different profile sheets with min.thickness of 0.50 mm |
| 138 | P/F of Ridge or hips,valley of plain GS sheets in ridges/valleys/gutters and wherever required includingfixing with J/L hooks all complete.(0.5 mm thick) |
| 139 | 45 cm |
| 140 | 60 cm |
| 141 | 90 cm |
| 142 | P/L Cement plaster of mix(1:4):(1 Cement:4 coarsesand) incl cost and carriage of materials involved complete. |
| 143 | 12 mm |
| 144 | 15 mm |
| 145 | Fabrication of wardrobe / almirahs/ kitchen cabnits 18 to 24 inchs deep made up of 19 mm thick blockboards frames, shutters shelves & 12 mm thick back incl.1mm thick dulmica lining on both exposed as well as inner surface with 19 mm thick shutters of block board with teak coat on exposed surface incl. providing supports brackets etc at regular intervals(2’-0”) and fixing of necessary hardware fittings viz locks handles catchers bolts etc complete. |
| 146 | Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : (15 mm wide and 15 mm deepgroove) |
| 147 | Providing and applying putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 148 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. |
| 149 | With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood). |
| 150 | With ready mixed red oxide Zinc Chromate primer ofapproved brand and manufacture on steel work |
| 151 | Wall Painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work. |
| 152 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.(two or more coats onnew work) |
| 153 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one ormore coats on old work. |
| 154 | Removing white or color wash /distemper/paint by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 155 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work. |
| 156 | Varnishing with varnish of approved brand and manufacturer( one or more coats.). |
| 157 | Applying knify grey paste of approved quality over wood/cement surface including sanding complete. |
| 158 | Removing old paint from wooden surface by scrapping/sand papering/using blow lump.etc |
| 159 | Renewing glass panes, with wooden fillets and nails wherever necessary. |
| 160 | Float glass panes of thickness 3.5mm to 4 mm thickness |
| 161 | Float glass panes of thickness 5 mm |
| 162 | P/F of Frosted glass of thickness 5 mm |
| 163 | Demolishing cement concrete manually/mechanical means including disposal of material within 500 meters lead as per direction of Engineer-incharge:(1:3:6 or richer mix) |
| 164 | Demolishing R.C.C. work manually/mechanical means including stacking of steel bars and disposal of unserviceable material within 500 meters lead as per direction of Engineer-in-charge. |
| 165 | Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: (In cement mortar). |
| 166 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead :Of area beyond 3 sqm |
| 167 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 meters lead. |
| 168 | (Dismantling tile work in floors, walls and roofs laid in cement mortar including stacking material within 50 meters lead.( For thickness of tiles 10 mm to 25 mm) |
| 169 | Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead. |
| 170 | Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead. |
| 171 | P/F white vitreous chins flat back or wall corner type lipped front urinal basin 430*260*350mm and 340*410*265 mm sizes respectively with flushing cistern with standard flush pipe and C.P brass spreaders with brass unions and G.I clamps complete including fittings and brackets cutting and making good the walls and floors and wherever required. (oneurinal basin with 5 litre white P.V.C flushing cistern. |
| 172 | Construction of WC Plateform including all materials, brickworks,sand cement concrete plaster all complete including dismantling of exisiting work as per direction of EIC complete. |
| 173 | p/f of sanitary fittings of standard quality: |
| 174 | Providing and fixing white vitreous china water closet squatting pan(Indian type) Orissa pattern W.C. pan of size 580x440 mm with integrated foot rest. |
| 175 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. |
| 176 | White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 177 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. Stainless Steel AISI- 304 (18/8) Orissa pattern W.C. pan of size 585x480mm with flush pipe and integrated type foot rests |
| 178 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:18.2.1 W.C. pan with ISI marked white solid plastic seat and lid |
| 179 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete White solid plastic seat with lid. |
| 180 | Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete 10 liter capacity -White |
| 181 | C.Plong bend 32 mm dia |
| 182 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps. |
| 183 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 184 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 185 | P/F of C.P fittings and fixtures (Approved Quality byEngineer Incharge) |
| 186 | bib cock long body |
| 187 | bib cock short body |
| 188 | pillar cock/sink cock |
| 189 | wall mixer two holes |
| 190 | cp arm |
| 191 | wall mixer with showers |
| 192 | Sink mixer(single hole) |
| 193 | Grating 100 mm |
| 194 | CP tube 45-60 cm |
| 195 | Towl Ring 8-9” |
| 196 | Cloth Hanger |
| 197 | soap case |
| 198 | Mixer leg |
| 199 | Towl Rod 60 cm |
| 200 | CP Nipple 15*25 mm |
| 201 | CP Nipple 15*50 mm |
| 202 | angle valve |
| 203 | C.P Cup |
| 204 | Geyser bolt set |
| 205 | Stainless steel sink |
| 206 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as perI.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040mm bowl depth 178mm |
| 207 | two in one Bibcock |
| 208 | P/F health faucet with 1 mm C.P chain |
| 209 | P/F of Telephonic shower with chain |
| 210 | P/F of high neck swan type C.P mixers Jacquar / approvedone with hot / cold controls. |
| 211 | P/F of elbow action C.P mixers of approved make |
| 212 | Providing and fixing 600x120x5mm glass shelf with edges round offsupported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete |
| 213 | PVC connection(24”) |
| 214 | PVC connection(18”) |
| 215 | PVC connection(36”) |
| 216 | P/ f spindle heavy duty for mixer and bib cock |
| 217 | P/F urinal C.P spreader heavy quality |
| 218 | p/f basin nut(tar chand) |
| 219 | P/F of CP waist for steel sinks heavy duty |
| 220 | 50mm dia |
| 221 | 75mm dia |
| 222 | 100mm dia |
| 223 | Providing of CP Knob (Gem/Parko) |
| 224 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. |
| 225 | PN-16 pipe, 16mm OD(SDR-7.4) |
| 226 | PN-16 pipe , 20mm OD(SDR-7.4) |
| 227 | PN-16 pipe , 25mm OD(SDR-7.4) |
| 228 | PN-16 pipe , 32mm OD(SDR-7.4) |
| 229 | PN-16 pipe , 40mm OD(SDR-7.4) |
| 230 | PN-16 pipe , 50mm OD(SDR-11) |
| 231 | Internal work Concealed fixing the pipe with clamps at1.00 meter spacing including cutting chases and making good the wall etc. |
| 232 | PN-16 pipe, 16mm OD(SDR-7.4) |
| 233 | PN-16 pipe , 20mm OD(SDR-7.4) |
| 234 | PN-16 pipe , 25mm OD(SDR-7.4) |
| 235 | PN-16 pipe , 32mm OD(SDR-7.4) |
| 236 | Providing and fixing PPR Unions of standard quality. |
| 237 | PPR Union 15mm |
| 238 | PPR Union 20mm |
| 239 | PPR Union 25mm |
| 240 | PPR Union 32mm |
| 241 | PPR Union 40mm |
| 242 | PPR Union 50mm |
| 243 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls, excavation work and refilling etc.complete.etc.(internal/external) |
| 244 | (A):(medium Grade ) |
| 245 | 15 mm dia. nominal bore |
| 246 | 20 mm dia. nominal bore |
| 247 | 25 mm |
| 248 | 32 mm |
| 249 | 40mm dia |
| 250 | 50 mm |
| 251 | (B)Concealed type including cutting chasses and making good the walls |
| 252 | 15 mm dia. nominal bore |
| 253 | 20 mm dia. nominal bore |
| 254 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floatscomplete. |
| 255 | 15 mm nominal bore |
| 256 | 20 mm nominal bore |
| 257 | 25 mm nominal bore |
| 258 | 32 mm nominal bore |
| 259 | 40 mm nominal bore |
| 260 | Providing and fixing C.P. brass shower rose with 15 or20 mm inlet. |
| 261 | 100 mm diameter |
| 262 | 150 mm diameter |
| 263 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete. |
| 264 | 15 mm nominal bore |
| 265 | 20 mm nominal bore |
| 266 | 32 mm nominal bore |
| 267 | 40 mm nominal bore |
| 268 | p/f G.I crossover(15 mm) |
| 269 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 270 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia.and size including Necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- Charge (glazing, panelling and dash fasteners to be paid for separately.) |
| 271 | Frames (powder coated) |
| 272 | Shutters (powder coated) |
| 273 | Anodized aluminum(Frames) |
| 274 | Anodized aluminum(Shutters) |
| 275 | Providing and fixing glazing in aluminum door, window, ventilator Shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in- Charge. (Cost of aluminum snap beading shall be paid in basic item.) |
| 276 | With floating glass panes of 3.5 to 4.0 mm thickness (weight not less than 10.00 kg / sqm) |
| 277 | With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm) |
| 278 | p/f of galvanized m.s wire guaze with 0.63 mm thk wire ofcomplete |
| 279 | P/F of alumunium composite panel of approvedmake(complete job) |
| 280 | 3 mm thick |
| 281 | 5 mm thick |
| 282 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).Including newel post complete. |
| 283 | P/F of 19mm thick board of approved quality and manufacture ( water proof ) in shelves , partitions, tables, access panel , shutters and other shutters etc. fixed with nails/ wood screws complete |
| 284 | Water proof |
| 285 | Commercial |
| 286 | P/F of 6 mm thick ( 3- Ply ) commercial plywood ofapproved make and manufacture in all types of work fixed with nails and wood screws etc. complete |
| 287 | P/F of 8 mm thick ( 3- Ply ) commercial plywood ofapproved make and manufacture in all types of work fixed with nails and wood screws etc.complete. |
| 288 | P/F of 10 mm thick ( 3- Ply ) commercial plywood of approved make and manufacture in all types of work fixedwith nails and wood screws etc.complete. |
| 289 | P/F of 12 mm thick ( 3- Ply ) commercial plywood of approved make and manufacture in all types of work fixedwith nails and wood screws etc.complete. |
| 290 | P/F of lamination of 0.8 mm thick of approved quality and manufacture and of required shade and color fixed with standard quality of adhesive in all types of works (fitted and finished area to be measures and paid 0including cost of adhesive etc. complete in all respects. |
| 291 | 0.8 mm thick plain |
| 292 | 1 mm thick plain |
| 293 | 1 mm thick textured. |
| 294 | 0.80 mm thick textured. |
| 295 | p/f of 20*12mm ornamental kail wood beeding fixed withnails and wood screw complete. |
| 296 | p/f of PVC angle beeding (25*25) |
| 297 | p/f of PVC beeding (20mm) |
| 298 | P/F of Flat pressed 3-layer pre-laminated Board (Lamination on both sides) of approved quality including cost of screws/adhesive complete. |
| 299 | 12mm thick |
| 300 | 18mm thick |
| 301 | P/F of hardware fittings of approved quality ISI make including fixing with necessary screws, nuts, bolts etc. complete. |
| 302 | Link rod Lock 11” long |
| 303 | Link rod Lock 8” long |
| 304 | P/F Plastic beading 25 mm ( approved one ) |
| 305 | P/F Multi purpose locks of required size approved one (link) or equivalent. |
| 306 | Regrinding of granite / marble / kota stone / mosaic flooring / skirting etc. including repairs of cracks / edges and including rubbing polishing etc. complete job. |
| 307 | Kerb stones 150 mm size chisel dressed on top and sizes of required length in 1:4 mix and pointing with cement morter 1:2 mix including making drainage openings complete. |
| 308 | Providing and Fixing |
| 309 | Fixing only |
| 310 | Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 meter lead as per direction of Engineer-in-Charge. |
| 311 | P/L precast cement concrete tiles 25 mm thick(rubber moulded)in foot path and court yard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing cleaning and curing complete on 20 mm thick bed of cement mortar 1:4(1-cement;4-coarse sand) dark shade using ordinary cement. |
| 312 | Providing and laying 50mm thick factory made cement concrete(rubber moulded) interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge |
| 313 | P/F heavy duty ball cock with 300 mm brass rod and ball complete incl. removing damaged one where ever required. |
| 314 | P/F of PVC heavy duty ball cock to fit into all kinds of flush tanks (compact one) of standard make (approved one)15mm dia |
| 315 | P/F C.I pipes and fittings of standard quality. |
| 316 | (A)Pipes |
| 317 | 150 mm dia |
| 318 | 100 mm dia |
| 319 | 75mm dia |
| 320 | 50mm dia |
| 321 | (B) Plain Bend |
| 322 | 150mm |
| 323 | 100mm |
| 324 | (c)Door Bend |
| 325 | 150mm |
| 326 | 100mm |
| 327 | (D)Reducer |
| 328 | 150*100mm |
| 329 | 100*75mm |
| 330 | 75*50mm |
| 331 | 20*15mm |
| 332 | (E)Cowl |
| 333 | 100mm |
| 334 | (F) Coller |
| 335 | 150mm |
| 336 | 100 mm |
| 337 | 75 mm |
| 338 | P/F lead coulked joints for C.I pipes |
| 339 | P-Trap/Floor trap 100 mm |
| 340 | P-Trap/Floor trap 150 mm |
| 341 | Plain Tee 100 mm |
| 342 | Plain Tee 150 mm |
| 343 | P/F of PVC pipes/ fittings of approved make and quality(prince or finolex) ISI quality of following diameter: |
| 344 | (A)Pipes |
| 345 | 32 mm |
| 346 | 40 mm |
| 347 | 50 mm |
| 348 | 75 mm |
| 349 | 100 mm |
| 350 | 150 mm |
| 351 | (B)Door Bend |
| 352 | 150 mm |
| 353 | 100mm |
| 354 | 75 mm |
| 355 | 50 mm |
| 356 | (C)plain Bend |
| 357 | 150 mm |
| 358 | 100mm |
| 359 | 75 mm |
| 360 | 50 mm |
| 361 | (D)Collar |
| 362 | 150 mm |
| 363 | 100mm |
| 364 | 75 mm |
| 365 | (E)plain-Tee |
| 366 | 50 mm |
| 367 | 75 mm |
| 368 | 100 mm |
| 369 | 150 mm |
| 370 | P-Trap(100 mm) |
| 371 | Floor-Trap(100 mm dia) |
| 372 | Waste pipe 32mm |
| 373 | 45 Degree Bend(100 mm) |
| 374 | Reducer(75-100 mm) |
| 375 | Door Tee(75 mm) |
| 376 | Door Tee(100 mm) |
| 377 | PVC Cowel |
| 378 | Elbow |
| 379 | 50 mm |
| 380 | 75 mm |
| 381 | 100 mm |
| 382 | 150 mm |
| 383 | P/F of M.S Push cocks 15mm complete (approved one) |
| 384 | P/F of C.I manhole covers with frame (heavy duty )approved ones of required shape and size |
| 385 | 600x600mm/600mm dia |
| 386 | 450x450mm/450mm dia |
| 387 | 300x300mm/225mm dia |
| 388 | P/F of G.I assorted fittings of nominal bore of ISI make heavy quality including dismantling including removing of old one wherever required (approved one) |
| 389 | 15mm nominal bore |
| 390 | Socket |
| 391 | Elbow |
| 392 | Nipple 75 mm long |
| 393 | Niple 100 Mm long |
| 394 | Tankey Nipple |
| 395 | 20 mm Nominal Bore |
| 396 | Socket |
| 397 | Elbow |
| 398 | Nipple 75 mm long |
| 399 | Niple 100 Mm long |
| 400 | Tankey Nipple |
| 401 | 25 mm Nominal Bore |
| 402 | Socket |
| 403 | Elbow |
| 404 | Nipple 75 mm long |
| 405 | Niple 100 Mm long |
| 406 | Tankey Nipple |
| 407 | 32 mm Nominal Bore |
| 408 | Elbow |
| 409 | Tankey Nipple |
| 410 | Insulation of exposed water supply pipes (including fittings) on walls and roof tops upto water storage tanks BWO 50 mm glass wool with chicken mesh woomed with 16-18 guage wire and finished with 6-8 mm 1:10 coat of POP/ cement finished and glove/ deru incl removal of damaged insulation and scaffolding and clearance of site after completion of job |
| 411 | 15 mm dia |
| 412 | 20 mm dia |
| 413 | 25 mm dia |
| 414 | 32 mm dia |
| 415 | 40 mm dia |
| 416 | 50 mm dia |
| 417 | P/F of Cornice/door profile for MDF wall panelling of required size |
| 418 | Providing and fixing 12mm MDF laminated imported anti skid water proof wooden flooring of approved brand and manufacture with 5mm foam & beading complete.as per the directions of EIC at site complete. |
| 419 | P/F of MDF wall panelling imported of Approved pattern and Brand/Make in desired color including framework all complete as per directions of EIC at site complete |
| 420 | P/F of 12 mm thick Nordic pine wall paneling (T&G) fully finished & four sides planned,fungus and termite proof (seasoned moisture content 8% to 15% imported type ISO :14001 approved including fixing with head less nails and inclusive all carriages, all taxes of allied material involved including Budloo wood frame work complete in all respects. |
| 421 | Providing and fixing of superior quality wall paper of approved brand, manufacture, color and design with necessary adhesive Gum powder fully chemicalised or favicol whichever is suitable including prepration of wall surface by way of sand papering, applying of POP/wall putty and other necessary repair , all complete at all heights as per specifications, drawings and as directed by Engineer In-charge etc. |
| 422 | Providing and fixing of KHATAM BANDI ceiling of first class budloo/firwood excluding the cost of frame work which is to be paid separately. |
| 423 | Changez Khani |
| 424 | Chaar Gul |
| 425 | Chaar Phool |
| 426 | Paanch Murabah |
| 427 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design |
| 428 | Inside size 30x30 cm including C.I. cover with frame |
| 429 | Inside size 45x45 cm including C.I. cover with frame |
| 430 | Inside size 60x60 cm including C.I. cover with frame |
| 431 | P/F of 2 mm thick poly carbonate sheets including cost ofscrews / washers complete. |
| 432 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportionof 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete |
| 433 | 150 mm dia. R.C.C. pipe |
| 434 | 200 mm dia. R.C.C. pipe |
| 435 | 250 mm dia. R.C.C. pipe |
| 436 | 300mm dia. R.C.C. pipe |
| 437 | 450 mm dia. R.C.C. pipe |
| 438 | 600 mm dia. R.C.C. pipe |
| 439 | P/F of welded mesh 25*25 mm as per the directions of EIC complete. |
| 440 | P/F of vertical blind curtains with locking arrangement ofapproved pattern and quality |
| 441 | P/F of Roller blind curtains with locking arrangement ofapproved pattern and quality |
| 442 | P/F of Zebra blind curtains with locking arrangement ofapproved pattern and quality |
| 443 | P/F of steel Rod including brackets |
| 444 | Providing Concrete breaker machine along with operator |
| 445 | Providing welded machine with welded Rod. |
| 446 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (Granite Work) |
| 447 | P/F frosting privacy film for glass windows / doors /partitions. |
| 448 | P/F M.S Grill of required pattern in frames of window etc. with M.S flat,square or round bars etc. including primary coat with approved steel primer all complete(fixed by welding/Rawl plugs ,screws etc. |
| 449 | P/F wooden D-type beading (20-25 mm) of imported wood as per the directions of EIC complete. |
| 450 | Providing and fixing UV stabilized fiberglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts and nuts 8mm dia. G.I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-violet stabilizer in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS: 10192 and IS: 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. (2mm thick corrugated (2.5\\" or 4.2\\" or 6\\") or step-down (2\\"or 3\\" or 6\\") as specified. |
| 451 | French spirit polishing, Two or more coats on new works including a coat of wood filler |
| 452 | French spirit polishing, one or more coats on old work |
| 453 | P/f vinyl flooring antibacterial fixed with standard quality adhesive of aprroved colour shade inc skirting etc all complete |
| 454 | Supply & Installation 2-3 mm thick self levelling Compound Containing high Quality synthetic resins special cement with selected fillers when mixed with water, Primer should be applied on sub floor to seal the pores etc as per direction of Engineer in Charge Complete |
| 455 | P/F of C.P fittings (Approved Quality byEngineer Incharge) |
| 456 | Telephonic wall mixer(including cp cups) |
| 457 | CP long bend |
| 458 | Basin Mixer(centre hole)(including cp cups) |
| 459 | Supplying of PVC pipes/ fittings of approved make and quality(prince or finolex) |
| 460 | Waste pipe(32mm) |
| 461 | Waste pipe(40mm) |
| 462 | Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete : |
| 463 | Cleaning of Malba bwo mechanical/manual means outside the premises of Hospital. |
| 464 | Removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive. |
| 465 | Engagement of hydra or crane for lifting of vehiles (LMV type) upto a lead of 5 kms. |
| 466 | Providing and fixing PVC wall panels 6 mm thick of standard size and 10mm thickness, fixed over GI metal strips framework as per manufacturer’s specifications. The rate shall include the cost of all materials, labour, adhesive, PVC edge angles/beadings for finishing around window and door openings, cutting, jointing, and all other accessories required to complete the work in all respects. |
| 467 | Providing and fixing in position wall paper washable type of approved brand and manufature as per the design approved by engineer incharge |
| 468 | P/F of (Pergo flooring) of approved pattern and design, sheds including cost of 6mm thick thermocol foam underneath / 25 mm thick cornice with fixing adhesive etc. complete in all respects. |
| 469 | P/F Balusters made of Ist class budloo wood with 63 x 63 mm x 2.5 ft. height ornamentally lathed Budlooeodar wood pegs fixed with C/C distance of 150 mm given it a victorian look ( Approved pattern / design ) complete in all respects. |
| 470 | P/F 75 x 60 mm moulded hand rails of Ist class deodar wood in straight / curved lengths complete in all respects. |
| 471 | Providing and fixing 15cm wide 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete with 0.63 mm thick with zinc coating not less than 275 gram/m2 |
| 472 | P/F vertical blind including cost of mechanical component involved on both sides. |
| 473 | Mat finished blinds 100 mm wide |
| 474 | PVC type 75 mm washable |
| 475 | Supply & fixing of ship chain / garden chain made in iron of 3 to 4 mm dia inclduing cost of side rings as per the directions of EIC complete. |
| 476 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. |
| 477 | First Class kail wood |
| 478 | Decorative ply wood both side decorative veneer (type 1) conforming to IS 1328 BWR type |
| 479 | Electric work |
| 480 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable of Polycab /Finolax / RR Kabels /Anchor/ salzer / make / eq. make as approved by department not below the rank of SDO in existing surface / recessed medium class PVC conduit, with 6Amps modular switch, modular plate of Anti backteria series of ABB L&T /Legrand /eq. make as approved by department not below the rank of SDO, fitted on suitable GI box and earthing the point with 1.5 s q.mm FRLS PVC insulated copper conductor single core cable etc. as required. (P+N+E) for Normal and invertor points per room is to be provided seperately ) |
| 481 | Wiring for power plug points with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in existing surface / recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for earthing as required. of Polycab /Finolex /Anchor / RR Kabels / Salzer make / eq. make as approved by department not below the rank of SDO. |
| 482 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in existing surface I recessed medium class PVC conduit as required. of Polycab / Finolex /Anchor / RR Kabel /Salzer make /eq. make as approved by department not below the rank of SDO. |
| 483 | 2 X 1.5 sq. mm +1 X1.5 sq. mm earth wire |
| 484 | 2X2.5 sq. mm +1 X 2.5 sq. mm earth wire |
| 485 | 2 X4 sq. mm + 1 X4 sq. mm earth wire |
| 486 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 487 | 2 X 10 sq. mm +1 X 6 sq. mm earth wire |
| 488 | Supply and fixing of 6-10 Sq.mm Copper thimbles to be crimped rolling of colour coded tape |
| 489 | Supplying and fixing following size modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required of ABB /L&T /Legrand /eq. make as approved by department not below the rank of SDO |
| 490 | 2 Module (75mmX75mm) |
| 491 | 4 Module (125mmX75mm) |
| 492 | 6 Module (200mmX75mm) |
| 493 | 8 Module (125mmX125mm) |
| 494 | 12 Module (200mmX150mm) |
| 495 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required of Anti backteria series of ABB/L&T /Legrand /eq. make as approved by department not below the rank of SDO |
| 496 | 5/6 A switch |
| 497 | 15/16 A switch |
| 498 | 3 pin 5/6 A socket outlet |
| 499 | 6 pin 15/16 A socket outlet |
| 500 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required of Anti backteria series of ABB /L&T /Legrand /eq. |
| 501 | 2 Module (75mmX75mm) |
| 502 | 4 Module |
| 503 | 6 Module |
| 504 | 8 Module |
| 505 | 12 Module |
| 506 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. (Anti backteria series of ABB /L&T /Legrand /make /eq. make as approved by department not below the rank of SDO) |
| 507 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 508 | supply and laying of 25 mm dia medium class PVC medium grade Conduit to berecessed on walls / floor complete with all allied accrues like bends, tees etc. for paving way of laving of wires of heating points /circults machine points /circuite and sub mains The job includes cutting of walls / floors with required hydraulic cutter and refacing of walls with cement plaster of required ratio or with P O.P after laying of conduits refacing to its original position by way of supply and applying of painting of required colour to effected area's complete matching with existing surface Anchor/Polycab/Finolex/TMT Plus /paralex make |
| 509 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, 3 nos. blades, 30 cm long down rod,suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. of Usha/Helonix / Orient /Crompton make or eq. make as approved by department not below the rank of SDO |
| 510 | Supply, Installation testing and commissioning of 250 mm sweep Exhaust Fans of Usha / Crompton Greaves / Havel's incl making of necessary connections and making of necessary space in walls / Windows as per site. The Job includes providing and fixing of shutter of suitable size backlite hylum sheet for fixing of exhaust fan of Usha /Crompton /Helonix /orient make or eq. make as approved by department not below the rank of SDO |
| 511 | Supply and fixing of 18 Watts LED surface mounted (Commercial type having aluminium Body and Housing ) downlighter having following specficafications .The luminaire should have a colour temperature of 6500°K, CRI≥80 and SDCM≤5. The downlighter shall be back lit & not side-lit. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). Luminaire shall be designed to emit initial system lumen output of 2160 lumens with minimum system efficacy of 120 lumen/watt. The luminaire housing should made of pressure die-cast aluminium. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20.Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, \\"FAT\\" before dispatch as per IS 10322 & IK Test. The luminary shall have average life of 50000 hrs operating temperature -10 C to + 45 C The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM8O issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab & BIS certificate for LED Luminaire & Driver. approved make Philips / Lighting techology / Trilux /wipro/ Endo / Igguzini /Regent make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM Letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO, prior to the supply of materials |
| 512 | Supply Installation, Testing and Commissioning of 1P 66, 50 Watt LED Flood Luminaries having Aluminium body of standard make dully isi marked to be fitted on walls / poles with necessary cliffs /Clamps with nuts and bolts complete job. The system efficacy of the luminaire shall be ≥120Im/w. The LEDs used in the luminaire shall be from either Lumileds, Osram, Nichia, APT Electronics and CREE make, shall have CCT of 5700°K, CR270, SDCM≤5, Life of 50000Hrs @ L70B50. The luminaire shall have IP rating of IP66 & IK rating of IK07. The luminaire shall have lens made of polycarbonate & optical cover made of toughened glass. The LED driver shall have operating voltage range of 140V to 270V, PF≥0.95 @ full load,THDs 10% @ full load, In-built surge protection of 4KV, HV Cut off @ 325V (±15V). The luminaire shall have 10KV SPD in-built inside the luminaire.. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver.of Philips / Lighting techology / Trilux/wipro/ Endo / Igguzini /Regent make.The Agency / firm must submit the Techanical data sheet (TDS) on OEM Letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of material |
| 513 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) of legrand / ABB /Schneider /L&T /Simens make |
| 514 | 8 way (4+24), double door |
| 515 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 516 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with lections, testing and commissioning etc. as required of legrand / ABB /Schneider /L&T mens make |
| 517 | Supplying and fixing of 32 Amps rating DP 240/415 volts (10KA) of Legrend L&T /ABB /Simens /Schinder make dully isi marked complete with connections |
| 518 | Supplying and fixing of 40 Amps rating DP 240/415 volts (10KA) of Legrend /L&T /ABB /Simens /Schinder make dully isi marked complete with connections |
| 519 | Supplying and fixing of 63 Amps rating DP 240/415 volts (10KA) of Legrend /L&T /ABB /Simens /Schinder make dully isi marked complete with connections |
| 520 | Repair of existing Acs including refilling of gas complete job. |
| 521 | Earth work excuation of hard /soft soil upto 2ft in depth and 1 ft in width by manual mechanical means with refilling of execuated Soil after cable including disposal of surplus soil. |
| 522 | Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoall coke and salt as required. The job includes providing and fixing of main hole PVC Chamber (300 mm x 30 mm) with its cover complete job |
| 523 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 524 | Providing and laying of shock proof Rubber mats of 2mt. x 1 mt. and 12 mm thick in size |
| 525 | Providing and fixing of Wall panels of approved, carved/Grooved design in the shape of regular/iregular panels of desired shape and size. Panels to be made up of 18mm thick HDHMR boards (BIS Certified) Incl. necessary frame work, fixtures, fittings and scafolding etc complete. The exposed surface shall be polished with Deluxe Deco Paint of approved design. all complete |
| 526 | Providing and Fixing imported HDHMR Mouldings 18 mm & 25 mm thick and width of different sizes and patterns as required in patterns as directed incl. cost of nails, silicon complete. |
| 527 | Painting with synthetic enamel paint Deco (Berger Jivan) of approved brand and manufacture with one or more coat of approved Wood primer to give an even shade of Two or more coats on old as well as new work mechanically including scrapping on the old existing paint with all procedures etc. including all carriages and up to floor V |
| 528 | Painting with synthetic PU (polyurethane) paint of approved brand and manufacture of required colour to give an even shade (high gloss finishe) using a spray gun two or more coats on New work including priming coat as per direction of engineer in charge complete job in all respects. |
| 529 | NB:- Any item(s) of work found necessary during the execution of the work, though not included in the BOQ, shall be executed with prior approval and shall be paid at par with the percentage rate quoted by the bidder,as per SSR 2022 or LMR as applicable. Please Enable Macros to View BoQ information |