|
| 1 | Taking out doors,windows and clearstory windows shutter (steel or wood)including stacking with in 50 metres lead of area 3.00 square metres and below as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government. |
| 2 | Dismantling roofing including ridges, hips,valley and gutters etc.and stacking the material within 50 metres lead of G.S. sheet. as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government . |
| 3 | Dismantling wood work in frames, trusses,purlins and rafters up to 10 metres span and 5 metres height including stacking the material with in 50 metres lead of sectional are below 40 square centimetres.as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government . |
| 4 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government . |
| 5 | Excavation in foundation, trenches etcetra in earth work in all kind of classification of soil such as pick work, jumper work, pick jumper work, blasting work, soft and hard blasting and doing work in saturated soil, including chiselling or wedging out rocks where blasting work is prohibited or any other mixed variety of soil including shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) upto any depths any quantum of water including slush which may arise during de-watering or removal of slush, lift upto any height stacking the excavated soil not more than 3 metres (Three metres) clear from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimetre) layers, when required into plinths, sides of foundation etcetra consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as per specification, approved drawing design as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within leads, lifts and other inciddentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 6 | Providing and laying mechanically mixed and vibrated, for Rainfoced cement concrete in open foundation for all type of structure complete using plain cement concrete grade M-10 (M-10) nominal mix 1:3:6 (one cement isto three sand isto six graded crushed stone aggregate 40mm( forty millimetre) nominal size in or under water and curing complete including pumping or bailing out water,dewatering removal of slush as required at site which may arrise at the time of laying under water complete for all heights/ depths including the cost of form work as per drawing and MORD techinical specifications section 800,900 and 1200 as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 7 | Squared rubble masonry coursed with hrd stone of approved quaility in foundation and plinth including raking out joins in cement mortar 1:6 (one cement isto six sand includi8ng curring complete ..as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government . |
| 8 | Second class brick masonry in common burnt clay F.P.S (Non modular) building bricks of class destignation 7.5 in in super structure above plinth level upto floor any level in cement mortar 1:6 (One Cement is to Six Sand), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 9 | Providing form work with steel plates 3.15mm. (Three decimal one five milimetre) thick welded with angle iron frame of 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre ) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies for all heights/depths of propping and centering below supporting floor to ceiling for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Lintel, beam,plinth beam girder,bresumers and cantilevers etc. as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases suspanded floor above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate \ 20 mm nominal size). |
| 11 | Providing and laying Tor steel of TATA/ SAIL/TISCO reinforcement for Reinforced cement concrete work including cutting, straighting, bending, binding and placing in position, including cost of binding wire complete for all floor level, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 12 | Steel work welded in built up sections of Tata in Trusses and trussed purlins in building, in beams joists channels,angles,tee,flats with connecting plates or angle cleats asin main and cross beams, hip and jack rafters, purlines connected to common rafters and the like. position and applying coat of approved steel primer using structural steel etc. as required and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government. |
| 13 | Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge |
| 14 | Providing and fixing ridges or hips 60cm (Sixty centimetres) overall width and 0.45mm (Zero decimal forty five milimetre) thick prepainted steel sheet ISI marked ridges (factory made) of TATA/SAIL/Reliance /Jindal steel shall be having proper Gola/shape of steel sheet with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted J or L hooks, bolts and nuts 6mm (Six milimetre) dia with prepainted G.I. limpet and bitumen washer complete with all accessories as required, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 15 | Providing and fixing M.S.BP sheet 1.66mm to 2mm thick in eaves board/Facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete(Base members of sttel work shall be measured & paid separtely)as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 16 | Providing and fixing G.I clip in metal ceilng system of 600x600 mm (Six hundred into six hundred milimetres) module which includews providing and fixing C wall angle of Size 20x30x20 mm made of 0.5 mm thick pre-painted stell along the perametre of the rom with help of nylon sleevs and wooden screws at 300mm centre to centre suspending the main C carrier of size 10x38x10mm made G.I.sheet 0.7mm thick the sofifit cleat 37x37x25x1.6 mm,rawl plugs of size 38x12 mm and C carriersuspension clip and main centre bracket at 1000mm C/C internal triangle shaped spring tee having height of 24 mm and width of 34mm made of GI shett 0.45 mm thick is the fixed to themain C carrier and in direction perpendicular to it at 600mm centre with help of suspension brackets. wherever ahe main c carrier and spring T have to join,C carrier and spring T connections have to be used .All sections to be galvanised @ 120gms/sqm(both side inclusive), fixing with clip in tiles into spring T with GI metal clip,as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 17 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).second class Sal wood as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 18 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in charge. (Note:- Butt hinges and necessary screws shall be paid separately)Second class Teak wood 35mm thick shutters as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 19 | Providing and fixing wire gauge shutters using galvanized M.S. wire gaugeI.S guage destignation 85 G with wire of dia 0.56 mm for doors windows and clearstorey windows including bright finished black enamelled iron hinges with necessary screw, 2nd class deodar woob 40 mm thick.as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 20 | 15 mm (Fifteen milimetre) thick cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and rounded angles any girth and finished even and smooth with cement mortar 1:6 (One cement isto Six sand), as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 21 | Pointing on stone work with cement mortar 1:3(1cement :3fine sand)Raised and cut pointing.as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 22 | Providing and fixing 250mmx10mm (Two hundred fifty milimetre into Ten milimetre) aluminum tower bolts (Barrel type) make of PILOT/SHEEL or equivalent anodized transparent or dyed to required shade and colour with screws etc. complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government. |
| 23 | Providing and fixing 250x16mm(Two hundred fifty into Sixteen milimetres) size anodized aluminum sliding door bolts anodized colour and shade with necessary bolts, nuts and screws etc. completed within all leads, lifts of materials and other incidentals. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government. |
| 24 | Providing and fixing 100mm (One hundred milimetres) size aluminium anodized make of PILOT/ Sheel handles anodized transparent or dyed to required colour and shade with necessary screws etcetra complete, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 25 | Wall painting (two coats) with acrylic colour emulsion paint of Asian paint/ Dulex paint/ Burger/ Nerolac Paint manufacture of approved shade for interior grade on undecorated concrete/ stone/ plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for making the surface complete, including carriage of materials within all leads, lifts and other incidental Charges. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 26 | Applying priming one coat(including priming coat) on previoussly painted wood based surface with enamel paint over new wood and wood based surfaceswith Nerolac/Asian /Burgeror its equivalent after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with Ready mixed paint brushing wood primer pink . as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government. |
| 27 | Providing and fixing 600x600x10mm (Six hundred into six hundred into Ten milimetre)vetrified altra double charge/ Ultra charge vitrified tilesKajaria/ Somany / Nitco/Jonson/Simpolo/ Rak in flooring, on a bed of 20 mm (Twelve milimetre) thick cement mortar 1:3 (One cement isto Three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto all floor level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 28 | Providing and fixing 600x600x10mm (Six hundred into six hundred into Ten milimetre)vetrified altra double charge/ Ultra charge vitrified tilesKajaria/ Somany / Nitco/Jonson/Simpolo/ Rak in skirting/dado, on a bed of 20 mm (Twelve milimetre) thick cement mortar 1:3 (One cement isto Three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto all floor level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 29 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes , having thermal stability for hot &cold water supply, including all CPVC plain & brass threated fittings, i/c fixing the pipe with clamps at 1.00 metre spacing. This includes jointing of pipes & fittings with one steps CPVC solvent cement and the cost of cutting chases and makeing good the same including testing of joints complete Concealed work,including cutting chases and making good the walls etc. 15mm nominal outer dia pipes internal work)as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 30 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes , having thermal stability for hot &cold water supply, including all CPVC plain & brass threated fittings, i/c fixing the pipe with clamps at 1.00 metre spacing. This includes jointing of pipes & fittings with one steps CPVC solvent cement and the cost of cutting chases and makeing good the same including testing of joints complete Concealed work,including cutting chases and making good the walls etc. 20mm nominal outer dia pipes internal work)as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 31 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: white Vitreous China Flat back wash basinsize 630x 450 mm with single 15 mm C.P.brass pillar tap as per direction of the engineer in charge, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. |
| 32 | Providing and fixing CP brass bib cock of approved quality 15mm (Fifteen milimetre) nominal bore and as per the entire satisfaction and direction of Engineer – in- Charge including carriage of materials within all leads and lifts and other incidental . The rate includes octroi, royalty, Malkana, toll tax, GST or other taxes imposed by the Government |
| 33 | Providing and fixing P.V.C. Waste pipe for sink or wash basin including PVC waste fittings complete Flexible pipe 32mm dia of approved brand.as per specifications, drawing complete in all respect including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, sale tax, GST or any other taxes imposed by the Governmen |
| 34 | Providing and fixing 600x450mm (Six hundred into Four hundred fifty milimetre) beveled edge mirror of superior glass mounted on 6mm (Six milimetre) thick hard board ground and fixed to wooden cleats with C.P. Brass screws and washers as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government. |
| 35 | roviding and fixing water tank make P.V.C. (Poly Venyl Chloride) SINTEX Finolex/Relpipe (Reliance)/ Vectus with tripple layer having capacity of 500 ( five hundred ) litres each tank ISI 12701 (Twelve thousand seven hundred one) G.I. (Galvanised Iron) necessary fittings including over flow pipe scour pipe etectera for inlet and outlet and inside connection 15mm (Fifteen milimetre) nominal bore ball valve and P.V.C. (Poly Venyl Chloride) cover with locking arrangements including placing with all height above ground level complete in all respect and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government |
| 36 | Providing and fixing white viterous china pedestial tpye water closet MATRIX EWC with jet pressure ( European type) with Jet pressure and ,10 (ten) litre low level PVC dual flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40mm (Forty milimetre) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required of HINDWARE /CERA/JAQUAR of Stat white/Snow white shade including carriage of materials within all leads and lifts and other incidentals. The rate includes octroi, royality, Malkana,Tol tax, GST or any other taxes imposed by the Government. |
| 37 | Applying one coat of water thinable cement primer of Asian paint/ Dulex paint/ Burger Paint on new concrete/ masonry/ plasterede surfaces after and including preparing the surface by thoroughly bruhsing the surface free from mortar dropping and other foreign matters sand papering the surface smooth complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government. |
| 38 | Applying Birla J.k. white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dirt, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete upto all floor level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government. |
| 39 | Distempering with Ist quality acrylic distemper, having VOC(Volatile Orgnaic Compound) content less then 50 grams/ litre.of approved brand and manufacture,whereever required to achive even shade and colour.two coats.as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government. |
| 40 | Painting steel work with delux multi surface paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge complete including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, sale tax, GST or any other taxes imposed by the Governmen |
| 41 | Fencing with angle iron post placed at required distance embeded in cement concrete blocks,every 15th post,last but one end post and corner post shall be strutted on both sides and end end post on one side only and provided with horizential lines and two diagonals interwoven with horizential wires,of barbed wire weighing 9.38 kg per 100m(minimum), between the two posts fitted and fixed with G.I staples, trun buckles etc.complete.(Cost of posts, struts, earth work and concrete work to be made per metre cost of total length of barbed wire used:- with G.I. barbed wire complete.as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge complete including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, sale tax, GST or any other taxes imposed by the Governmen Please Enable Macros to View BoQ information |
