|
| 1 | Disconnecting /dismantling /taking out the defective burnt out VT pump set (Moter/Pump) from jack well and transporting to shop including loading/unloading etc complete and reffixing again after necessary repair work of capacity 30/50 HP Vertical motor. The repair includes followingsa) Dismantling/taking out strip opening /inspection complete of the bowl assembly, column pipe assembly, discharge head assembly etc and cleaing/ servicing overhauling all the servicable spare parts and M &L for painting to exposed surfaces of the column pipe assembly, bowl assembly and discharge head assembly etc with two coats of approved quality anticorrosive water resistant type black paint all as directed including labours for replacement of worn out / unservicable parts as required and directed.b) Reassembling the complete pump set and re-erection and re-installation at its original position as directedc) Testing and commissioning complete all as directed by Engr-in-Charge.Note:1) The rate quoted by the tenderer includes all cost of necessary nut bots washers and alike if not included in Sch A2) All new parts required will be measured and paid separately as supply only items.3) The rate quoted by the tenderer also includes cost for taking out pump from the well 20m depth from GL and again lowering the same in its original level and alignment complete.4)The size of wiring to be incorporated in the work shall be as per existing one hence contractor is requested to visit the site and to get acquanted with site conditions complete. 5)T&P , Transport etc incl in quated rate . 6) Location :Keniya Pump House and A-I Pump House |
| 2 | Supply for repair suction case bearing for 30 HP VT Pump set of Capacity 30 HP.Make: Jyoti |
| 3 | Supply for repair suction case bearing for 50 HP VT Pump set of Capacity 50 HP.Make:Jyoti |
| 4 | Supply for repair Impeller seal ring of Capacity 30 HP.Make:Jyoti |
| 5 | Supply for repair Impeller seal ring of Capacity 50 HP.Make:Jyoti |
| 6 | Supply for repair bowl bearing of Capacity 30 HP.Make:Jyoti |
| 7 | Supply for repair Bowl Bearing of Capacity 50 HP.Make:Jyoti |
| 8 | Supply for repair Bowl studs (SS) of Capacity 30 HP.Make:Jyoti |
| 9 | Supply for repair Bowl studs (SS) of Capacity 50 HP.Make:Jyoti |
| 10 | Supply for repair Line shaft coupling (SS) of Capacity 30 HP.Make:Jyoti |
| 11 | Supply for repair Line shaft coupling (SS) of Capacity 50 HP.Make:Jyoti |
| 12 | Suppy for repair Bearing holder assembly of Capacity 30 HP.Make:Jyoti |
| 13 | Supply for repair Bearing holder assembly of Capacity 50 HP.Make:Jyoti |
| 14 | Supply for repair Line shaft Bearing (Throdan type) of Capacity 30 HP.Make:Jyoti |
| 15 | Supply for repair Line shaft Bearing (Throdan type) of Capacity 50 HP.Make:Jyoti |
| 16 | Supply for repair Column studs /nut bolts (50 Nos) of Capacity 30/50 HP.Make:Jyoti |
| 17 | Supply for repair Stuffing box bush of Capacity 30 HP.Make:Jyoti |
| 18 | Supply for repair Stuffing box bush of Capacity 50 HP.Make:Jyoti |
| 19 | Supply for repair Latern Ring of Capacity 30/50 HP.Make:Jyoti |
| 20 | Supply for repair Water deflector of Capacity 30/50 HP.Make:Jyoti |
| 21 | Supply for repair Head shaft coupling of Capacity 30 HP.Make:Jyoti |
| 22 | Supply for repair Head shaft coupling of Capacity 50 HP.Make:Jyoti |
| 23 | Supply for repair Column pipe 150 mm of Capacity 30/50 HP.Make:Jyoti |
| 24 | Supply for repair Impeller adjusting nut with screw of Capacity 30/50 HP.Make:Jyoti |
| 25 | Supply for repair Impeller made out of MS with impeller key 30/50 HP complete all as directed |
| 26 | Supply for repair Strainer Assembly of Capacity 30/50 HP.Make:Jyoti |
| 27 | Supply for repair Bowl of Capacity 30 HP.Make:Jyoti |
| 28 | Supply for repair Bowl of Capacity 50 HP.Make:Jyoti |
| 29 | Supply for repair Impeller shaft of Capacity 30 HP.Make:Jyoti |
| 30 | Supply for repair Impeller shaft of Capacity 50 HP.Make:Jyoti |
| 31 | Supply for repair Impeller collect assemly of Capacity 30/50 HP.Make:Jyoti |
| 32 | Supply for repair Line shaft up to 1.5 mtr and replacement of the Line shaft coupling complete all as directed |
| 33 | Supply for repair NDE Bearing No 6307/C3 suitable for 30/50 HP Make SKF OR equivalent |
| 34 | Supply for repair electric connection box of ebonite materials with Insulators, lugs , protection cover suitable for 30/50 HP. |
| 35 | Disconnections suction and discharge line connection,Diconnection coupling motor of centrifugal pump of discharge capacity 120 LPS with head 100 mtr, motor capacity150 HP . Lifting and removing pump form its existing foundation. Dismantling the pump carefully checking, segregating serviceable,repairable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like shaft, key,Impellior,bearing upper casing etc) including replacement of unserviceable parts as required (The same will be measured and paid separately in respectable items mention bellow). Reassembling the pump including painting with two coats of synthetic enamel paint after necessary surface preparation , marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed . Pump Make=Kirloskar.Model No DSM 150/46. Location: Keniya Pump House. Note:(i) Spare parts for repair/replace will measured in respective items as per site required |
| 36 | Repair the Impeller with metaling, grinding,polishing,balancing with true shape Suitable for pump set Model no DSM 150/46 ,Kirloskar. |
| 37 | Repair the Pump shaft with metaling, grinding,polishing,balancing with true shape Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 38 | Supply Coupling Key Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 39 | Supply Key for Impeller SSuitable for pump set Model no DSM 150/46 ,Kirloskar |
| 40 | Supply Key for Sleeve Nut Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 41 | Supply Bolt for upper and lower half casing Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 42 | Supply Taper pin with washers and nuts for lower and upper half casingCoupling Key suitable for DSM 150/46 ,Kirloskar |
| 43 | Supply Drain plug for casing suitablefor 150 HP pump . Suitable for DSM 150/46 ,Kirloskar |
| 44 | Supply Paper packing between lower and upper casing Key Suitable for pump set Model no DSM 150/46 |
| 45 | Supply O ring for shast sleev Suitable for pump set suitable for Model no DSM 150/46 ,Kirloskar |
| 46 | Supply Wear Ring suitable for Pump set Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 47 | Supply Shoulder Ring in CI Suitable for pump set Model no DSM 150/46 150 HP |
| 48 | Supply Interstage Ring Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 49 | Supply Lantern Ring Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 50 | Supply DE ball bearing Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 51 | Supply DE Bearing Cover Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 52 | Supply Cartridge for bearing, DE Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 53 | Supply NDE Bearing Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 54 | Supply Cartridge for bearing, NDE Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 55 | Supply Bearing cover, NDE Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 56 | Supply Bearing Cap Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 57 | Supply Bearing nut,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 58 | Supply Shaft sleeve, DE/NDE,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 59 | Supply stuffing box bush,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 60 | Supply Water Deflector DE/NDE,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 61 | Supply Air vent,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 62 | Supply Hex screw for bearing cover,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 63 | Supply Cylindrical pin,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 64 | Supply Round Lock nut ,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 65 | Supply Gland Packing,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 66 | Supply Vent Valve,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 67 | Supply Flexible ST Hose Pipe,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 68 | Supply Gland stuffing box suitable for nut and bolts Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 69 | Disconnections suction and discharge line connection,Diconnection coupling motor of centrifugal pump of discharge capacity 100 LPS with head 100 mtr, motor capacity120 HP . Lifting and removing pump form its existing foundation. Dismantling the pump carefully checking, segregating serviceable,repairable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like shaft, key,Impellior,bearing upper casing etc) including replacement of unserviceable parts as required (The same will be measured and paid separately in respectable items mention bellow). Reassembling the pump including painting with two coats of synthetic enamel paint after necessary surface preparation , marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed . Pump Make=Kirloskar.Model No DSM 150/46. Note:(i) Spare parts for repair/replace will measured in respective items as per site required centrifugal pump of discharge capacity 100 LPS with head 100 mtr, motor capacity120 HP Pump Make=Kirloskar.Model No RKB-100/23E35. Location: Keniya Pump House |
| 70 | Repair the Impeller 1st stage with metaling, grinding,polishing,balancing with true shape Suitable for pump set Model no RKB-100/23E35Make-Kirloskar. |
| 71 | Repair the Impeller 2nd stage with metaling, grinding,polishing,balancing with true shape Suitable for pump set Model no RKB-100/23E35Make-Kirloskar. |
| 72 | Repair the Pump shaft with metaling, grinding,polishing,balancing with true shape Suitable for pump set Model no- RKB-100/23E35Make-Kirloskar. |
| 73 | Supply Coupling Key Suitable for pump set Model no- RKB-100/23E35,Make-Kirloskar. |
| 74 | Supply Key for Impeller Suitable for pump set Model no- RKB-100/23E35,Make-Kirloskar. |
| 75 | Supply Key for Sleeve Nut Suitable for pump set Model no- RKB-100/23E35,Make-Kirloskar. |
| 76 | Supply Bolt for upper and lower half casing Suitable for pump set.Model no- RKB-100/23E35,Make-Kirloskar. |
| 77 | Supply Taper pin with washers and nuts for lower and upper half casingCoupling Key suitablefor Model no- RKB-100/23E35,Make-Kirloskar. |
| 78 | Supply Draing plug for casing suitablefor 15 HP pump .Model no- RKB-100/23E35,Make-Kirloskar. |
| 79 | Supply Paper packing between lower and upper casing Key Suitable for pump setModel no- RKB-100/23E35,Make-Kirloskar. |
| 80 | Supply O ring for shast sleev Suitable for pump set.Model no- RKB-100/23E35,Make-Kirloskar. |
| 81 | Supply Wear Ring suitable for Pump set Suitable for pump set .Model no- RKB-100/23E35,Make-Kirloskar. |
| 82 | Supply Shoulder Ring in CI Suitable for pump set .Model no- RKB-100/23E35,Make-Kirloskar. |
| 83 | Supply Interstage Ring Suitable for pump set. Model no- RKB-100/23E35,Make-Kirloskar. |
| 84 | Supply Lantern Ring Suitable for pump set .Model no- RKB-100/23E35,Make-Kirloskar. |
| 85 | Supply DE ball bearing Suitable for pump set. Model no- RKB-100/23E35,Make-Kirloskar. |
| 86 | Supply DE Bearing Cover Suitable for pump set. Model no- RKB-100/23E35,Make-Kirloskar. |
| 87 | Supply Cartridge for bearing, DE Suitable for pump set. Model no- RKB-100/23E35,Make-Kirloskar. |
| 88 | Supply NDE Bearing Suitable for pump set .Model no- RKB-100/23E35,Make-Kirloskar. |
| 89 | Supply Cartridge for bearing, NDE Suitable for pump set .Model no- RKB-100/23E35,Make-Kirloskar. |
| 90 | Supply Bearing cover, NDE Suitable for pump set. Model no- RKB-100/23E35,Make-Kirloskar. |
| 91 | Supply Bearing Cap Suitable for pump set. Model no- RKB-100/23E35,Make-Kirloskar. |
| 92 | Supply Bearing nut,Suitable for pump set. Model no- RKB-100/23E35,Make-Kirloskar. |
| 93 | Supply Shaft sleeve, DE/NDE,Suitable for pump set .Model no- RKB-100/23E35,Make-Kirloskar. |
| 94 | Supply stuffing box bush,Suitable for pump set. Model no- RKB-100/23E35,Make-Kirloskar. |
| 95 | Supply Water Deflector DE/NDE,Suitable for pump set Model no DSM 150/46 ,Kirloskar |
| 96 | Supply Air vent,Suitable for pump set .Model no- RKB-100/23E35,Make-Kirloskar. |
| 97 | Supply Hex screw for bearing cover,Suitable for pump set.Model no- RKB-100/23E35,Make-Kirloskar. |
| 98 | Supply Cylindrical pin,Suitable for pump set .Model no- RKB-100/23E35,Make-Kirloskar. |
| 99 | Supply Round Lock nut ,Suitable for pump set .Model no- RKB-100/23E35,Make-Kirloskar. |
| 100 | Supply Gland Packing,Suitable for pump set. Model no- RKB-100/23E35,Make-Kirloskar. |
| 101 | Supply Vent Valve,Suitable for pump set Model no- RKB-100/23E35,Make-Kirloskar. |
| 102 | Supply Flexible ST Hose Pipe,Suitable for pump set Model no- RKB-100/23E35,Make-Kirloskar. |
| 103 | Supply Gland stuffing box suitable for nut and bolts Suitable for pump set Model no- RKB-100/23E35,Make-Kirloskar. |
| 104 | Disconnections suction and discharge line connection,Diconnection coupling motor of centrifugal pump of discharge capacity 130 LPS with head 105 mtr, motor capacity75 HP . Lifting and removing pump form its existing foundation. Dismantling the pump carefully checking, segregating serviceable,repairable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like shaft, key,Impellior,bearing upper casing etc) including replacement of unserviceable parts as required (The same will be measured and paid separately in respectable items mention bellow). Reassembling the pump including painting with two coats of synthetic enamel paint after necessary surface preparation , marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed . Pump Make=Kirloskar.Model No DSM 150/46. Note:(i) Spare parts for repair/replace will measured in respective items as per site required centrifugal pump of discharge capacity 130 LPS with head 105 mtr, motor capacity75 HP Pump Make=GRUNDFOS .Location :- Keniya Pump House. |
| 105 | Kit Chamber stack CRN155-4A,suitable for 75 HP centrifugal Pump,Make : Grand Force. |
| 106 | Mechanical Seal.uitable for 75 HP centrifugal Pump,Make : Grand Force. |
| 107 | Bulk Impeller 99262569,uitable for 75 HP centrifugal Pump,Make : Grand Force. |
| 108 | Shaft 99196563,uitable for 75 HP centrifugal Pump,Make : Grand Force. |
| 109 | Kit wear part,uitable for 75 HP centrifugal Pump,Make : Grand Force. |
| 110 | Kit Bearing,uitable for 75 HP centrifugal Pump,Make : Grand Force. |
| 111 | AIR &AF Charges,uitable for 75 HP centrifugal Pump,Make : Grand Force. |
| 112 | Disconnections suction and discharge line connection,Diconnection coupling motor of centrifugal pump of discharge capacity 34 LPS with head 60/75 mtr, motor capacity 60 HP . Lifting and removing pump form its existing foundation. Dismantling the pump carefully checking, segregating serviceable,repairable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like shaft, key,Impellior,bearing upper casing etc) including replacement of unserviceable parts as required (The same will be measured and paid separately in respectable items mention bellow). Reassembling the pump including painting with two coats of synthetic enamel paint after necessary surface preparation , marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed . Pump Make=Kirloskar.Model No DSM 80/36. Note:(i) Spare parts for repair/replace will measured in respective items as per site required centrifugal pump of discharge capacity 130 LPS with head 75 mtr, motor capacity 60 HP Pump Make=Kirloskar .Location :- MIDC Pump House. |
| 113 | Repair the Impeller with metaling, grinding,polishing,balancing with true shape Suitable for pump set Model no DSM/80/36,Kirloskar |
| 114 | Repair the Pump shaft with metaling, grinding,polishing,balancing with true shape Suitable for pump set Model no DSM/80/36 ,Kirloskar |
| 115 | Supply Wear Ring suitable for Pump set,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 116 | Supply Shoulder Ring in CI suitable for PUMP set,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 117 | Supply Interstage Ring suitable for Pump set,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 118 | Supply Lantern Ring suitable for Pump set,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 119 | Supply Gland suitable for Pump set,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 120 | Supply DE Bearing s,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 121 | Supply NDE Bearing ,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 122 | Supply Deep Groove Ball bearing suitable for 60 HP,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 123 | Supply ANG Contact Ball bearing,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 124 | Supply Bearing Cover,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 125 | Supply Cover NDE,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 126 | Supply Shaft Sleeve,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 127 | Supply Key for Impeller,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 128 | Supply Key for Coupling,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 129 | Supply Key for Sleeve Nut,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 130 | Supply Shaft Sleeve Nut ,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 131 | Supply Round Lock nut ,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 132 | Supply Gland Packing,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 133 | Supply Vent Valve,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 134 | Supply Set of O Ring ,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 135 | Supply Flexible ST Hose Pipe,,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 136 | Supply Ms stud and including replacement of CI gland ,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 137 | Supply stuffing box suitable for nut and bolts,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 138 | Supply Cooling PVC flexible of ,suitable for Model No DSM/80/36,Make: Kirloskar. |
| 139 | Disconnections suction and discharge line connection,Diconnection coupling motor of centrifugal pump of discharge capacity 36000 GPS with head 122 mtr, motor capacity 100 HP . Lifting and removing pump form its existing foundation. Dismantling the pump carefully checking, segregating serviceable,repairable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like shaft, key,Impellior,bearing upper casing etc) including replacement of unserviceable parts as required (The same will be measured and paid separately in respectable items mention bellow). Reassembling the pump including painting with two coats of synthetic enamel paint after necessary surface preparation , marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed . Pump Make=Kirloskar.Model No Model No K1225 Note:(i) Spare parts for repair/replace will measured in respective items as per site required centrifugal pump of discharge capacity 36000 GPS with head 122 mtr, motor capacity 100 HP Pump Make=Kirloskar .Location :- A-2 Pump House. |
| 140 | Repair the Impeller with metaling, grinding,polishing,balancing with true shape Suitable for pump set Model No K1225 Make : Kirloskar |
| 141 | Repair the Pump shaft with metaling, grinding,polishing,balancing with true shape Suitable for pump set Model No K1225 Make : Kirloskar |
| 142 | Supply Wear Ring suitable for Pump set,suitable for Model No K1225 Make : Kirloskar |
| 143 | Supply Shoulder Ring in CI suitable for PUMP set,suitable for Model No K1225 Make : Kirloskar |
| 144 | Supply Interstage Ring suitable for Pump set,suitable for Model No K1225 Make : Kirloskar |
| 145 | Supply Lantern Ring suitable for Pump set,suitable for Model No K1225 Make : Kirloskar |
| 146 | Supply Gland suitable for Pump set,suitable for Model No K1225 Make : Kirloskar |
| 147 | Supply DE Bearing suitable for Model No K1225 Make : Kirloskar |
| 148 | Supply NDE Bearing suitable for Model No K1225 Make : Kirloskar |
| 149 | Supply Deep Groove Ball bearing suitable for Model No K1225 Make : Kirloskar |
| 150 | Supply ANG Contact Ball bearing,suitable for Model No K1225 Make : Kirloskar |
| 151 | Supply Bearing Cover,suitable for Model No K1225 Make : Kirloskar |
| 152 | Supply Bearing Cover NDE,suitable for Model No K1225 Make : Kirloskar |
| 153 | Supply Shaft Sleeve suitable for Model No K1225 Make : Kirloskar |
| 154 | Supply Key for Impeller,suitable for Model No K1225 Make : Kirloskar |
| 155 | Supply Key for Sleeve Nut,suitable for Model No K1225 Make : Kirloskar |
| 156 | Supply Shaft Sleeve Nut ,suitable for Model No K1225 Make : Kirloskar |
| 157 | Supply Round Lock nut,suitable for Model No K1225 Make : Kirloskar |
| 158 | Supply Gland Packing,suitable for Model No K1225 Make : Kirloskar |
| 159 | Supply Vent Valve,suitable for Model No K1225 Make : Kirloskar |
| 160 | Supply Set of O Ring ,suitable for Model No K1225 Make : Kirloskar |
| 161 | Supply Gland stuffing box suitable for nut and bolts suitable for Model No K1225 Make : Kirloskar |
| 162 | Disconnections suction and discharge line connection,Diconnection coupling motor of centrifugal pump of discharge capacity 10000 GPS with head 26 Mtr, motor capacity 15/20 HP . Lifting and removing pump form its existing foundation. Dismantling the pump carefully checking, segregating serviceable,repairable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like shaft, key,Impellior,bearing upper casing etc) including replacement of unserviceable parts as required (The same will be measured and paid separately in respectable items mention bellow). Reassembling the pump including painting with two coats of synthetic enamel paint after necessary surface preparation , marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed . Make : Kirloskar OR Equivalent Note:(i) Spare parts for repair/replace will measured in respective items as per site required centrifugal pump of discharge capacity 10000 GPS with head 26 Mtr, motor capacity 15/20 HP Pump Make=Kirloskaror equivalent.Location :- C-1 and C-2 Pump House,COD Depot,FAD Depot. |
| 163 | Repair the Impeller with metaling, grinding,polishing,balancing with true shape Suitable for pump15/20 HP set Make : Kirloskar OR Equivalent |
| 164 | Repair the Pump shaft with metaling, grinding,polishing,balancing with true shape Suitable for pump set 15/20 HPMake : Kirloskar OR Equivalent |
| 165 | Supply Wear Ring suitable for Pump set,suitable for Pump 15/20 HP Make : Kirloskar OR Equivalent |
| 166 | Supply Shoulder Ring in CI suitable for PUMP set 15/20 HP,suitable for Make : Kirloskar OR Equivalent |
| 167 | Supply Interstage Ring suitable for Pump set 15/20 HP,suitable for Make : Kirloskar OR Equivalent |
| 168 | Pump shaft Suitable for pump set 15/20 HP for Make : Kirloskar OR Equivalent |
| 169 | DE/NDE Bearing No 6306 suitable for Make : Kirloskar OR Equivalent |
| 170 | Shaft bush for 15/20 HP Pump including removal from the pumps,Make : Kirloskar OR Equivalent |
| 171 | Shaft coupling flexible type KC 276 FOR 15/20 HP Cappacity in repair and removal from pumps Make : Kirloskar OR Equivalent |
| 172 | Star Nuts for 15/20 HP Centrifugal pump Make : Kirloskar OR Equivalent |
| 173 | Impeller for 15/20 HP Centrifugal pump Make : Kirloskar OR Equivalent |
| 174 | Impeller wear ring Model no KDS 15/20 HPMake : Kirloskar OR Equivalent |
| 175 | Bearing housing.Model no KDS 15/20 HP Make : Kirloskar OR Equivalent |
| 176 | Disconnections suction and discharge line connection,Diconnection coupling motor of centrifugal pump of discharge capacity 25LPS with head 25 Mtr, motor capacity 10 HP . Lifting and removing pump form its existing foundation. Dismantling the pump carefully checking, segregating serviceable,repairable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like shaft, key,Impellior,bearing upper casing etc) including replacement of unserviceable parts as required (The same will be measured and paid separately in respectable items mention bellow). Reassembling the pump including painting with two coats of synthetic enamel paint after necessary surface preparation , marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed . Make : Kirloskar OR Equivalent Note:(i) Spare parts for repair/replace will measured in respective items as per site required centrifugal pump of discharge capacity 25LPS with head 25 Mtr, motor capacity 10 HP Pump Make=Kirloskaror equivalent.Location :- COD Depot,FAD Depot.STP |
| 177 | Repair the Impeller with metaling, grinding,polishing,balancing with true shape Suitable for pump15/20 HP set Make : Kirloskar OR Equivalent |
| 178 | Repair the Pump shaft with metaling, grinding,polishing,balancing with true shape Suitable for pump set 15/20 HPMake : Kirloskar OR Equivalent |
| 179 | Pump shaft Suitable for pump set 10 HP.Make : Kirloskar |
| 180 | DE/NDE Bearing of capacity 10 HP.Make : Kirloskar |
| 181 | Shaft bush for 10 HP Pump including removal from the pumps.Make : Kirloskar |
| 182 | Shaft coupling flexible type 10 HP Cappacity in repair and removal from pumps.Make : Kirloskar |
| 183 | Star Nuts for 10 HP Centrifugal pump Make : Kirloskar |
| 184 | Impeller for 10 HP Centrifugal pump.Make : Kirloskar |
| 185 | Disconnection the electric and pum connection and transportation to work shop for repair and back,taking out burnt winding coils from stator body cleaning of slots with soft wire brush and rewinding by using super enameled copper wire of existing size & gauge, heat and varnishing complete and M&L winding with super enamal copper wire of existing gauge including greasing, varnishing and alike testing and painting with two cote of synthetic eanamel paint,complete suitable for Squirrel cage electric motor of capacity 150 HP 3 phase 415 Volt AC supply. (make : kirlosker ) |
| 186 | All as item no 9 here in before but Squirrel cage electric motor of capacity120 HP 3 phase 415 Volt AC supply. ( make : kirlosker ) |
| 187 | All as item no 9 here in before but Squirrel cage electric motor of capacity 75/60 HP 3 phase 415 Volt AC supply. (make : kirlosker ) |
| 188 | All as item no 9 here in before but Squirrel cage electric motor of capacity 30 HP 3 phase 415 Volt AC supply. (make : kirlosker ) |
| 189 | All as item no 9 here in before but Squirrel cage electric motor of capacity 15/20 HP 3 phase 415 Volt AC supply ( make : kirlosker ) |
| 190 | All as item no 9 here in before but Squirrel cage electric motor of capacity 10 HP 3 phase 415 Volt AC supply ( make : kirlosker ) |
| 191 | All as item no 9 here in before but Squirrel cage electric motor of capacity 5 HP/3 HP 3 phase 415 Volt AC supply ( make : kirlosker ) |
| 192 | Disconnection the electric and lifting the submersible pump from river bed,well and transportation to work shop for repair and back,taking out burnt winding coils from stator body cleaning of slots with soft wire brush and rewinding by using super enameled copper wire of existing size & gauge, heat and varnishing complete and M&L winding with super enamal copper wire of existing gauge including greasing, varnishing and alike testing complete suitable for Submersible motor with pump of capacity 15 HP 3 phase 415 Volt AC supply. |
| 193 | All as item no-16 here in before but capacity of submersible pump 10 HP |
| 194 | Taking down the Slip ring assy complete with studs made out of copper suitable for 150 HP Capacity Motor and supply and fixing the same all as directed. |
| 195 | Taking down the Slip ring assy complete with studs made out of copper suitable for 120 HP Capacity Motor and supply and fixing the same all as directed. |
| 196 | Taking down the Slip ring assy complete with studs made out of copper suitable for 60 HP Capacity Motor and supply and fixing the same all as directed. |
| 197 | Taking down the Carbon bush holder made of bronze suitable for 150 HP Capacity Motor and supply and fixing the same all as directed |
| 198 | Carbon brushes holder made of bronze as per existing sizes per sample suitable for 120 HP Capacity Motor |
| 199 | Carbon brushes holder made of bronze as per existing sizes per sample suitable for 60 HP Capacity Motor |
| 200 | Taking down the unserviceable Fan Blade upto 20 HP Motor and supply fixing the same. |
| 201 | Taking down the unserviceable Fan Blade upto 30 HP Motor and supply fixing the same. |
| 202 | Taking down the unserviceable Fan Blade upto 60 HP Motor and supply fixing the same. |
| 203 | Taking down the unserviceable Fan Blade upto 100-150 HP Motor and supply fixing the same. |
| 204 | S&F in repair electric connection box of ebonite materials with Insulators, lugs , protection cover suitable for 30 HP. |
| 205 | Supply and Fixing Pressure gauge (100 mm dial) with gunmetal/brass connection suitable range 0-10 Kg/Cm2 complete with isolation cock, fittings,fixing and testing and commissioning on pump delivery line as directed by Engineer In charge |
| 206 | Supply and Fixing Panel type analog ammeter (96 x 96 mm) suitable for pump motor current measurement , CT operated (0-100/5 A or suitable range) complete with current transformer , wiring , fixing ,testing and commissioning in pump control panel as directed by Engineer In charge |
| 207 | Supplying and Fixing Panel type analog voltmeter (96 x 96 mm) suitable for 0-500 V AC range complete with volt selector switch , wiring , fixing , testing and commissioning in pump control panel as directed by Engineer In Charge |
| 208 | Supply and Fixing Panel type analog ammeter (96 x 96 mm) suitable for pump motor current measurement , CT operated (0-200/5 A or suitable range) complete with current transformer , wiring , fixing ,testing and commissioning in pump control panel as directed by Engineer In charge |
| 209 | Supply and Fixing flexible coupling suitable for connecting pump (30-50 HP Pump) and Motor shaft complete with coupling hubs, rubber bushes/ spider nuts, bolts and key , properly aligned and installed for smooth trnasmission of between pump and motor , including all necessary accessories as required |
| 210 | Supply and Fixing flexible coupling suitable for connecting pump (100-150 HP Pump) and Motor shaft complete with coupling hubs, rubber bushes/ spider nuts, bolts and key , properly aligned and installed for smooth trnasmission of between pump and motor , including all necessary accessories as required |
| 211 | Supply and Fixing star delta starter of 415 V 3 Phase induction motor AC 3 duty complete with coil auxilary contacts terminals and mounting arrangement , suitable for 15 HP pump motor control panel including fixing on exisitng panel of same make and same rating as specified and directed |
| 212 | Supply and Fixing star delta starter of 415 V 3 Phase induction motor AC 3 duty complete with coil auxilary contacts terminals and mounting arrangement , suitable for 60 HP pump motor control panel including fixing on exisitng panel of same make and same rating as specified and directed |
| 213 | Supply and Fixing star delta starter of 415 V 3 Phase induction motor AC 3 duty complete with coil auxilary contacts terminals and mounting arrangement , suitable for 100 HP pump motor control panel including fixing on exisitng panel of same make and same rating as specified and directed |
| 214 | Supply and Fixing star delta starter of 415 V 3 Phase induction motor AC 3 duty complete with coil auxilary contacts terminals and mounting arrangement , suitable for 120 HP pump motor control panel including fixing on exisitng panel of same make and same rating as specified and directed |
| 215 | Supply and Fixing star delta starter of 415 V 3 Phase induction motor AC 3 duty complete with coil auxilary contacts terminals and mounting arrangement , suitable for 150 HP pump motor control panel including fixing on exisitng panel of same make and same rating as specified and directed |
| 216 | Supply and Fixing MCCB (Moulded Case Circuit Breaker) 100 A 4 Pole 415 V 50 HZ thermal magnetic release with adjustable overload and short circuit protection breaking minimum 25 KA suitable for installation in pump control panel / MCC panel including and fixing same make as specified and directed |
| 217 | Supply and Fixing MCCB (Moulded Case Circuit Breaker) 160 A 4 Pole 415 V 50 HZ thermal magnetic release with adjustable overload and short circuit protection breaking minimum 25-36 KA suitable for installation in pump control panel / MCC panel including and fixing same make as specified and directed |
| 218 | Supply and Fixing MCCB (Moulded Case Circuit Breaker) 250 A 4 Pole 415 V 50 HZ thermal magnetic release with adjustable overload and short circuit protection breaking minimum 25-36 KA suitable for installation in pump control panel / MCC panel including and fixing same make as specified and directed |
| 219 | Supply and Fixing MCCB (Moulded Case Circuit Breaker) 400 A 4 Pole 415 V 50 HZ thermal magnetic release with adjustable overload and short circuit protection breaking minimum 36 KA suitable for installation in pump control panel / MCC panel including and fixing same make as specified and directed |
| 220 | Supply and Fixing MCCB (Moulded Case Circuit Breaker) 630 A 4 Pole 415 V 50 HZ thermal magnetic release with adjustable overload and short circuit protection breaking minimum 36-50 KA suitable for installation in pump control panel / MCC panel including and fixing same make as specified and directed |
| 221 | Supply and Fixing Rotary selector switch 2/3 Position (Auto-Off- Manua/On-Off))suitable for 415 V control panel operation complete with contact blocks, knob and mounting arrangement including wiring and fixing as required Make : L&T/Schneider/Seimens/ABB or Equivalent |
| 222 | Supply and Fixning CT suitable for ammeter connection ratio required 100/ 5A,200/5A and 400 /5 A accuracy class 1.0 resin cast type complete with mounting and terminal connections for electric control panel as specified and directed |
| 223 | Supply and Fixing Electronic Timer suitable for star delta motor starter adjustable time range 0-30 Sec coil voltage 230 V AC complete with base and connections for pump motor starter panel as specified and directed |
| 224 | Taking up the unserviceable cable of any type,and supply , laying testing and commissioining of PVC Insulated and PVC Round Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Flexible Cables for Voltage Grade 1100 Volts conforming to 1C x 50 sqmm include all accessories glands,copper lugs ,ferruling , dressing,clamping and termination as required Make : Polycab,Finolex,Havells |
| 225 | Taking up the unserviceable cable of any type,and Supplying , laying testing and commissioining of PVC Insulated and PVC Round Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Flexible Cables for Voltage Grade 1100 Volts conforming to 1C x 70 sqmm include all accessories glands,copper lugs ,ferruling , dressing,clamping and termination as required Make : Polycab,Finolex,Havells |
| 226 | Taking up the unserviceable cable of any type,and Supplying , laying testing and commissioining of PVC Insulated and PVC Round Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Flexible Cables for Voltage Grade 1100 Volts conforming to 1C x 25 sqmm include all accessories glands,copper lugs ,ferruling , dressing,clamping and termination as required Make : Polycab,Finolex,Havells |
| 227 | Taking down the unserviceable Starter from the existing panel and MU-G 15 DOL Star-Delta Starter for 10 HP squrrel cage induction motor Make L&TCat no CS94901, C&S, Havells or equivalent |
| 228 | Taking down the unserviceable Starter from the existing panel and MN 16 DOL Starter for 3/ 5 HP Motor L&TCat no SS94351, C&S, Havells or equivalent |
| 229 | 4 Pole Power Contactors - Type MCX 4 Pole Power Contactors [8536] l Range from 16A contactor Make: L & T/C&S/Havells or equivalent |
| 230 | 4 Pole Power Contactors - Type MCX 4 Pole Power Contactors [8536] l Range from 160A contactor Make: L & T/C&S/Havells or equivalent |
| 231 | 4 Pole Power Contactors - Type MCX 4 Pole Power Contactors [8536] l Range from 100A contactor Make: L & T/C&S/Havells or equivalent |
| 232 | S&F in repair Single phase preventor as reqd on site fpr protection of starter complete all as specified and directed Make: L & T/C&S/Havells or equivalent Please Enable Macros to View BoQ information |
| 233 | S&F in repair Single phase preventor as reqd on site fpr protection of starter complete all as specified and directed Make: L & T/C&S/Havells or equivalent Please Enable Macros to View BoQ information |