|
| 1 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. a) In ground floor including roof . |
| 2 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm . |
| 3 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes(b) River bazree. |
| 4 | Ordinary cement concrete ( mix 1:1.5:3) with graded stone chips with (20 mm normal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes(ii) River Bazree. |
| 5 | Brick work with 1st class bricks in cement mortar (1:4) (b) In superstructure, ground floor. |
| 6 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars ,stirrups, binders etc. initial straightening and removal of loose rust ( if necessary), cutting to requisite length hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction.(a) For works in foundation,basement and upto roof of ground floor/upto 4m) (i)Tor steel/Mild steel III. Others manufacturers not specified. |
| 7 | Hire and labour charges for shuttering with centering and necessary staging upto 4.0m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs,beams and columns,lintels curved or straight including fitting, fixing and striking out after completion of work (upto roof of ground floor) (a) 25 mm to 30mm thick wooden shuttering as per decision and direction of the EIC. |
| 8 | Plaster (to wall ,floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course scaffolding/staging where necessary (Ground floor) (c) 10 mm thick with 1:4 cement mortar. |
| 9 | Supplying,fitting & fixing 1st quality Ceramic tiles in wall and floors to match with the existing work and 4nos of key stone(10mm)fixed with aralidiet at the back of each tile and finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includuing roughining of concrete surface if nececcary or by synthetic adhesive and grout material etc (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(b) Area of each tile above 0.09 Sq.m(ii) Other than Coloured decorative including white . |
| 10 | Supplying,fitting & fixing 1st quality Ceramic tiles in wall and floors to match with the existing work and 4nos of key stone(10mm)fixed with aralidiet at the back of each tile and finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includuing roughining of concrete surface if nececcary or by synthetic adhesive and grout material etc(B)WALL with sand cement mortar(1:3) 15mm thick and 2mm thick cement slurry at back side of tiles using [email protected]/sqm and joint filling using white cement slurry @0.20kg/sq m (b) Area of each tile above 0.09 Sq.m (ii) Other than Coloured decorative including white . |
| 11 | Synthetic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats. |
| 12 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification In Ground floor: (iii) Two coats. |
| 13 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made) ii) 40mm thick shutters with 19mm thick panel of size 30 to 45 cm (c) Other Local Wood. |
| 14 | Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts) , reassembling and refitting and rehanging same with old fittings but with new screws as necessary. (Where different parts of same shutter are renewed under different item, payment under item 73 will be made once only). |
| 15 | M.S. structural works in roof trusses with tubular sections conforming to IS: 806-1968 & IS: 1161- 1998 cnnected to one another with bracket, gusset cleats as per design, direction of Engineer-in-charge complete including cutting to requisite size, fabrication with necessary metal arc welding conforming to IS: 816- 1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour reqired for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural tubular memebrs as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a height of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof. |
| 16 | b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 17 | A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary (a) On timber or plastered surface With other than hi-gloss of approved quality-(iv) Two coats (with any shade except white). Please Enable Macros to View BoQ information |
