|
| 1 | Repair to pot holes any depth, not exc 1.0 sqm each including sweeping free from dust and mud, or water, scouring sunken surfaces in roads , paths etc. cutting around edges to at least 25mm in depth making good by applying tack coat @ 5 kg per 10 sqm, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 kg per 10 sqm blinded with 0.09 cum of stone, chippings, 6.3 mm size and again rammed (including supply of premixed macadam, binder and chippings) depth of potholes exc 30 mm complete all as specified and directed. |
| 2 | M&L for laying premix bituminous macadam (consolidated thickness 75mm or less) with paving bitumen VG-30 @ binder content of 4% by weight of total mix (design mix), prepared in hot mix plaint, laid/rolled and compacted to required gradient and camber with 08 to 12 tonne power roller and vibratory roller etc complete all as specified and directed. |
| 3 | M&L for preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags or mechanical air compressor machine to remove all loose dirt etc and applying evenly a priming/tack coat with bituminous primer at 5 kg per 10 sqm using paving bitumen VG-10 complete all as specified and directed. |
| 4 | M&L for providing bituminous premixed asphaltic semi dense concrete (design mix) 30mm consolidated thickness using paving bitumen VG-30 @ 5.5% binder content by weight of total mix, laid/spread uniformly by means of mechanical pavers over primed black top surfaces rolled and compacted to required camber and gradient using 10 to 12 tonne power roller, complete all as specified and directed complete all as specified and as directed. |
| 5 | M & L for preparing bituminous surfaces of road and marking 2.5mm thick center or edge line, stop lines, dashes, arrows, etc and the like n exc 10 cm wide hot applied thermo plastic road marking paint (reflective type ) of uniform finishing with machine conforming to BS 3262 (Part-I) 1989 read with most specification of 803 clause 4.2.1 and 4.2.2 on bituminous surface in white / yellow/ red colour and super imposed with glass slam beats conforming to BS 6088 and most specification 803 clause 4.3.3 including cleaning of surface by removing all dust dirt oil grease etc including removing of existing marking with spirit / kerosene / gas burner or mechanically on bituminous surface complete all as specified and directed. |
| 6 | Surface dressing n. exc. 15 cm deep and averaging 10 cm deep and getting out in hard/dense soil complete all as specified and directed. |
| 7 | M&L for 100mm thick (spread thickness) moorum/red bajri brought from out side MD land, filling in layers not exceeding 10cm thick, spread watered , rolled and consolidated with 8 to 12 tonne power roller to required camber and gradient, complete all as specified and directed. |
| 8 | Supply and fix in repair solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. complete all as specified and directed. |
| 9 | Supply and fixing in repair cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and directed. |
| 10 | S&F road safety convex mirror 800 mm dia or over , SS supporting pipe of suitable dia , PVC canopy at top of mirror to prevent the mirror from rain water shower etc. including fixing and anchoring with PCC 1:2:4 grout complete all as specified and directed. Make- Oscar, Pioneer, Shakti or Equivalent |
| 11 | Supply and fixing in repair metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed |
| 12 | Demolition of cement concrete of any description and in any position not otherwise specifically not provided for complete all as specified and directed. |
| 13 | M & L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed. |
| 14 | Dismantling stone slabs and tiles of any description or thickness laid , bedded and pointed in any mortar as in floors, aprons etc. complete all as specified and directed. |
| 15 | Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed. |
| 16 | M&L for 75 mm thick cement concrete type D2 1:4:8 (using 40 mm graded stone agg) in sub base of flooring/ hard standing complete all as specified and directed by Engineer-in-Charge. |
| 17 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. |
| 18 | M&L for preparation of newly concrete wall surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of priming paint plaster coat complete all as specified and directed. |
| 19 | M&L for preparation of old painted surface of concrete wall of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of priming paint plaster coat complete all as specified and directed. |
| 20 | Manufacturing, supplying and fixing retro reflective Cautionary / warning sign boards of equilateral triangular or rectangular shape having one side of minimum 900 mm for triangle and 1200 mm for rectangle with support length of 3650 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message , symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge. |
| 21 | Manufacturing, supplying and fixing double legged informatory sign board fixed on single SS frame and meeting back to back on the SS round pipe. Name on sign should be on both side. The boards are of high intensity blue colour of retro-reflective grade having sheeting of AVERY DENNISON made out of 2 mm thick Alcobond/aluminium sheet conforming to IS 736 to be covered with high intensity grade retro-reflective sheeting (avery dennison) of blue colour as per user. The whole is fixed to sheet and fixed with suitable adhesive to alco bond/alluminium sheet painted with epoxy paint to standard make, fixed to structural frame work of SS pipe of size 35 mm OD with nuts, bolts/rivets ensuring safely against removal of plates. The lettering is computerised cut of high intensity grade white sheetig (Avery Dennison) and mechanically fixed on this board of blue colour . Then these two separate boards fixed back to back on single frame are fixed to two vertical stainless steel posts of 50mm dia, 2.60 m (2.00 AGL +0.60 BGL) mtr height. This boards on single frame are fixed in position using embedment in PCC 1:2:4 including excavation in post hole. The size of board is 1.20m x 1.20m. Please Enable Macros to View BoQ information |