Name of Work:- Replacement of cable and street light for restoration of street light on poles along the periphery of the godown at FSD Churachandpur under Manipur region. | Sl. No. | Item Description | |
| 1 | Supplying, Installation, Testing & Commissioning of Street light LED fixture (45 WATT) , powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC,frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical circuitary) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (Asper ANSI Bin), SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the pecified rating and Fixture shall be of relevant BIS standard complete in allrespect i/c external connections with 1.5 sq mmFRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixturesas per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge asper requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). | | 2 | Supplying and fixing of 32 mm dia X 1.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required | | 3 | Supply 2x10 sqmm PVC insulated and PVC sheathed/ XLPE POWER CABLE of 1.1 kV grade armoured Al. cable compulsory ISI mark conforming to IS:7098/ PART-I/ 88 e as required. | | 4 | Laying and fixing of one number PVC insulated andPVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle) | | 5 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sqmm | | 6 | Laying of one No. PVC insulated & PVC sheathed/XLPE POWER CABLE of 1.1 kv grade aof follwing size in existing masonry open duct as required. Upto 35 sqmm. | | 7 | P/F of cable termination of M.S. box of size 15cm X 15cm X 10 cm with compression termination arrangements, 6-10 Amp SP MCB and double natural link etc as required. | | 8 | Supplying and drawing following sizes of FRLS/HFFRPVC insulated copper conductor, single core cable inthe existing surface/ recessed steel/ PVC conduit as required.3x1.5 sqmm Please Enable Macros to View BoQ information |
|