|
| 1 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge. |
| 2 | Demolishing cement concrete manually / by mechanical means including disposal of material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge:- |
| 3 | (i) Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 4 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 5 | Float glass panes of thickness 4 mm |
| 6 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 7 | Clearing & uprooting of banian trees in/c roots from the roof & walls of different office buildings/qtrs in/c disposal of rubbish etc. Upto 50.00 mtr. as per directon of the Eng-in-Charge |
| 8 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. - All kinds of soil |
| 9 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - - All work upto plinth level : |
| 11 | (i) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) |
| 12 | ii)1:2:4 ( 1 Cement: 2 fine sand :4 graded well burnt brick aggregate 20 mm nominal size) |
| 13 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement--All work upto plinth level: |
| 14 | (i)1:2:4 ( 1 Cement: 2 fine sand : 4 graded brick aggregate 20 mm nominal size) |
| 15 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement- |
| 16 | (i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 17 | Centering shuttering including struttings, propping etc. and removal of form work for: |
| 18 | (i) Suspended floors, roofs, landings, balconies and access platform with timber planks |
| 19 | (ii) Weather shade, Chajjas, corbels etc., including edges. |
| 20 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 21 | (i) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 22 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 23 | (i) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 24 | First class brick work in foundation and plinth including cost of all materials as required complete:- |
| 25 | (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 26 | Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:- |
| 27 | (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 28 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- i)In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 29 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with : |
| 30 | Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 31 | Providing and applying Super Latex (SBR based) or equivalent water proofing coating over RCC slab with 3 components by mixing Super Latex or equivalent, water and cement at 1:4:7 ratio or as per manufactuerer recommendation including cleaning the roof surface with wire brushing and with clean water before applicaton and curing the chemicals by sprinkling water for 3 to 5 days after application of wate proofing compound complete as per direction of the Engineer-In-Charge and technical instruction of the manufacturer. |
| 32 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : |
| 33 | (i) Local Teak wood |
| 34 | Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20 × 12 mm for fixing panelling and or glazing as per direction of Engineer-In-Charge. |
| 35 | (i) Local Teak wood - 35mm thick shutters |
| 36 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters. |
| 37 | 35 mm thick including ISI marked stainless steel but hinges with necessary screws. |
| 38 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 39 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. i) Fixed to openings /wooden frames with rawl plugs screws etc. |
| 40 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:- |
| 41 | (i) In grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 42 | Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws. |
| 43 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter). |
| 44 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 45 | Providing and fixing IS : 1341 marked M.S. heavy weight butt hinges with necessary screws etc. complete : |
| 46 | (i)100 × 75 × 3.50 mm |
| 47 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : |
| 48 | (i) 250x10 mm |
| 49 | (ii) 150x10 mm |
| 50 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : |
| 51 | (i)125 mm |
| 52 | Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc. complete. (i)300 x 16 mm |
| 53 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. |
| 54 | (i) Single rubber stopper |
| 55 | Providing and laying cement concrete 1:2:4 (1 cement: 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips etc.complete. |
| 56 | (i) 25mm thick with 12.5 mm well burnt brick aggregate. |
| 57 | Providing and fixing 1st quality ceramic glazed wall tiles (minimum 200 x 300) conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in-charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. |
| 58 | Providing and laying ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete450 mm X 300 mm in all shades & design. |
| 59 | (A) Mat Finish Tiles/Anti Skid/Glossy Tiles(i) 300 x 300mm in all shades and designs |
| 60 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: |
| 61 | Single socketed pipe- 110 mm OD |
| 62 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type-A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: |
| 63 | (a) coupler(i) 110 mm |
| 64 | (b) single equal tee without door(i) 110 x110x110 mm |
| 65 | ( c) single equal tee with door(i) 110 x110x110 mm |
| 66 | (d) Bend 87.5`(i) 110 mm |
| 67 | (e) Plain shoe(i) 110 mm |
| 68 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. |
| 69 | 110 mm |
| 70 | Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. |
| 71 | 110 mm |
| 72 | 12 mm cement plaster of mix |
| 73 | Cement mortar 1:4 (1 cement : 4 fine sand) |
| 74 | 15 mm cement plaster on the rough side of single or half brick wall of mix: |
| 75 | Cement mortar 1:4 (1 cement : 4 fine sand) |
| 76 | 6 mm cement plaster of mix : |
| 77 | In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 78 | Neat cement punning. |
| 79 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 80 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture, of required shade and colour complete, as per manufacurer's specification. [Payment shall be made after submission of Test Certificate issued by the Manufacturer] |
| 81 | Two or more coats on new work. |
| 82 | Distempering with 1st quality acrylic washable distemper of approved brand and manufacture and of required shade on old work ( one or more coats ) to give an even shade as required complete as per direction of the Engineer in charge. |
| 83 | Providing and fixing wall mixture 3 in 1 system with provision of both Hand shower and Overhead Shower with 115 long bend pipe of Hindware make having company catalouge no. F390022 or equivalent as per direction of the Engineer in Charge. |
| 84 | Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS: 14842- 2000, in/c top cover of 6 mm coir veneer board, nickel plated M.S pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets in/c fixing with 25x3 mm M.S flat 10 cm long and rawl plugs 50 mm long (designation 10 no.) etc. all complete. |
| 85 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 86 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: |
| 87 | Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture |
| 88 | Painting with synthetic enamel paint ( one or more coats ) of required colour of approved brand and manufacture on old work to give an even shade including preparation of surface as required complete as per direction of the Engineer in charge. |
| 89 | Providing and fixing white vitreous china water closet squatting pan (Indian type) |
| 90 | Orissa pattern W.C. pan of size 580x440 mm |
| 91 | Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. |
| 92 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 93 | 10 litre capacity-White |
| 94 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : White solid plastic seat with lid |
| 95 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : |
| 96 | i) White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar taps. |
| 97 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: |
| 98 | Kitchen sink without drain board - 610x460 mm bowl depth 200 mm. |
| 99 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 100 | Flexible pipe - 32 mm dia |
| 101 | Providing and fixing PTMT Waste Coupling for washbasin and sink, of approved quality and colour. Waste coupling 38mm of 83mm length and 77mm breadth, weighing not less than 60gms. |
| 102 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : i) Rectangular shape 453 x 357 mm |
| 103 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 104 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. |
| 105 | (i)450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms. |
| 106 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 107 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: |
| 108 | 100 mm diameter |
| 109 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 110 | (a) 45 cm length(i) 20 mm nominal bore |
| 111 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : |
| 112 | (i) 15 mm nominal bore |
| 113 | (ii) 20 mm nominal bore |
| 114 | (iii) 25 mm nominal bore |
| 115 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 116 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): |
| 117 | (i) 32 mm nominal bore |
| 118 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 |
| 119 | 15 mm nominal bore |
| 120 | Providing and fixing PTMT bib cock approved quality and colour |
| 121 | (i) 15mm nominal bore, 86mm long , Weighing not less than 88 gms. |
| 122 | Providing and fixing PTMT stop cock of approved quality and colour (i)15 mm nominal bore, 86 mm long,weighing not less than 88gms. |
| 123 | Providing and fixing PTMT pillar cock of approved quality and colour . |
| 124 | (i) 15mm nominal bore, 125mm long foam flow, Weighing not less than 120 gms. |
| 125 | Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85gms. |
| 126 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall |
| 127 | (i) 15 mm nominal outer dia .Pipes. |
| 128 | (ii) 20 mm nominal outer dia .Pipes. |
| 129 | (iii) 25 mm nominal outer dia .Pipes. |
| 130 | (iv) 32 mm nominal outer dia .Pipes. |
| 131 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work |
| 132 | (i) 15 mm nominal outer dia .Pipes. |
| 133 | (ii) 20 mm nominal outer dia .Pipes. |
| 134 | (iii) 25 mm nominal outer dia .Pipes. |
| 135 | (iv) 32 mm nominal outer dia .Pipes. |
| 136 | (iv) 40 mm nominal outer dia .Pipes. |
| 137 | Providing and fixing brass bib cock of approved quality : |
| 138 | 15 mm nominal bore |
| 139 | Providing and fixing brass stop cock of approved quality : |
| 140 | 15 mm nominal bore |
| 141 | Providing and fixing gun metal non-return valve with C.I. wheel of approved quality (screwed end): |
| 142 | (i) 25 mm nominal bore(a) Horizontal |
| 143 | (ii) 25 mm nominal bore(b) Vertical |
| 144 | (iii) 32 mm nominal bore(a) Horizontal |
| 145 | (iv) 32 mm nominal bore(b) Vertical |
| 146 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : |
| 147 | (i) 15 mm nominal bore |
| 148 | (ii) 20 mm nominal bore |
| 149 | (ii) 25 mm nominal bore |
| 150 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 4 kg / cm²) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: |
| 151 | Single socketed pipe- 110 mm OD |
| 152 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: |
| 153 | (a) coupler(i) 110 mm |
| 154 | (b) single equal tee without door(i) 110 x110x110 mm |
| 155 | ( c) single equal tee with door(i) 110 x110x110 mm |
| 156 | (d) Bend 87.5`(i) 110 mm |
| 157 | (e) Plain shoe(i) 110 mm |
| 158 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC soil, waste & vent pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. |
| 159 | 110 mm |
| 160 | Providing and fixing to the inlet mouth of soil, waste & vent pipes pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. |
| 161 | 110 mm |
| 162 | Labour chages for dismantling and fitting fixing of GI pipe line after washing the internal bore including removal of iron deposited in the existing portion as per direction of the Engineer-in-charge. |
| 163 | Clearing of septik tanks, inspection chambers, etc. including removing of blockade in sewer connection pipeline and disposal of night soil with all lifts and upto a lead of 1000m complete as per direction of Engineer-in-Charge. Please Enable Macros to View BoQ information |