|
| 1 | Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified and directed. |
| 2 | Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed . |
| 3 | S & F 4 mm thick of size 600x600mm HSPC (High Pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed GI grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19x0.9 mm duly suspended with 2mm dia SS bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified and directed. |
| 4 | S&F 5mm thick PVC sheet fillets of width 35mm for wall panelling including of fixxing on to wall making PVC frame as per specification and drawing complete all as specified and directed. |
| 5 | M&L for solid PVC wall lining consisting of 5mm thick plain or coloured with wood grains printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed. |
| 6 | M&L for 25mm thick PCC 1:2:4 type B-0, using 12.5mm graded stone aggregate in floor to receive the surface of tiles complete all as specified and directed. |
| 7 | S&F light shade vitrified ceramic tiles 8 to 10mm thick area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, each in floors laid over and including 15mm thick screed bed or bedding layer of mortar in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 8 | S&F light shade vitrified ceramic tiles 8 to 10mm thick on vertical surfaces such as skirting, dado risers to steps fixed over and including 10 mm thick bedding layer in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 9 | S&F Non skid ceramic colour floor tiles of 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc laid over and including 15mm thick screed bed or bedding layer of mortar in CM (1:6), set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed. |
| 10 | S&F Non skid ceramic colour floor tiles of 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm in floors etc with 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6), set and jointed in neat cement slurry and pointed in coloured cement all as specified and directed. |
| 11 | M&L for coloured Glazed ceramic tiles in vertical surface such as dado etc 450mmX 300mmX 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles fixed over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed. |
| 12 | M&L for 20mm thick granite work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite fixed over including 15mm thick screed bed or bedding layer in cement mortar 1:6 etc complete all as specified and directed. |
| 13 | M&L for 100 mm thick PCC 1:3:6, type C-2, (using 40 mm graded stone aggregates) as in sub base completel all as specified and directed. |
| 14 | M&L for Chequered cement concrete tiles of size 30 cm X 30 cm X 25 mm thick, set jointed and pointed in neat cement slurry and with grey pigment cement and pigments in floors laid over and including 15 mm screed bed or bedding layer of mortar in CM 1:6 complete all as specified and directed. |
| 15 | M & L for machine pressed precast concrete interlocking paver block with grey cement and pigmnet any shape and size confirming to IS 15658-2006 of 100 mm thickness , M-50 Grade with coloured finishes on top laid over sand dust cushions complete all as specified and directed. Note - Sand for cusioning will be measured and paid seperatly |
| 16 | M & L for sand filling ( as cusioning under interlocking paver block) including watering and consolidation complete all as specified and directed. |
| 17 | M & L for PCC 1:2:4 type B-1 using 20mm graded aggregate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 18 | Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed. |
| 19 | Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed. |
| 20 | S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed. |
| 21 | S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed. |
| 22 | Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar and taking out of trenches, if required, internal dia of pipe in 75MM/100mm/150MM complete all as specified and directed. |
| 23 | S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. |
| 24 | S&F 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, laid in trenches or in floors and jointed complete all as specified and directed |
| 25 | M&L for PCC 1:3:6 type C-2 (using 40mm grade stone aggregate) as in bed to 110/100 mm dia SGSW /PVC pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 26 | S&F 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, fixed to wallscomplete all as specified and directed. |
| 27 | S & F PVC (SWR) bends/sockets any radius 110 mm dia complete all as specified and directed. |
| 28 | S & F stack clamp,110mm/75mm bore made out of 50mm by 5 mm flat iron/pvc and 16 mm dia round stays including bolts and nuts and securing ends of stay to wall or roof complete all as specified and directed. |
| 29 | Demolition of brick work or stone boulder masonry built in cement mortar or cement lime including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 30 | M&L for brick work with sub class 'B' bricks built in CM 1:6 straight or curved on plan & exc 6 m mean radius with old size bricks complete all as specified and directed. |
| 31 | Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar complete all as specified and directed. |
| 32 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and finished even and smooth (without using extra cement) complete all as specified and directed. |
| 33 | M&L for rendering 15mm thick in CM 1:4 other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 34 | M&L for preparation of new plastered or unplastered surface of walls including cornices, pilasters etc and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty including washing floors, cleaning glass, joinery, electric fittings,wiring etc of drops and splashes and leaving premise, clean and tidy etc complete all as specified and as directed. |
| 35 | M&L for preparation of new plastered or un plastered surface of walls including cornices, pilasters etc and applying two coats of weather proof exterior emulsion paint over a coat of primer complete all as specified and directed. |
| 36 | M&L for exterior acrylic emulsion on old decorated plastered or un-plastered surfaces of wall surfaces in disruptive / camouflaging pattern of six / four shades comporising the following activities complete all as specified and directed by Engr-in-Charge:- (i) Preparing old decorated plaster or un-plastered surfaces of wall by scraping the surfaces, brooming down or steel wire brushing down smoke soot, mould, moss and efflorescence salts and trading oil and greesy Spots etc.(ii) Preparation of old wall surfaces for height not exceeding 12.00 Mtr.(iii) Applying two coats of water based exterior acrylic emulsion as in base coat over a coat of primer.(IV) Applying two coats of exterior acrylic emulsion in disruptive / camouflaging pattern of six / four shades (Camouflage pattern shall be approved by Stn Auth Or Engr-In-Charge). |
| 37 | M&L for 75mm thick PCC 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection and paving, laid in slope finished even and smooth without using extra cement including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified and directed. |
| 38 | M&L for 100 mm thick PCC 1:2:4, type B-2, (using 40 mm graded stone aggregates) as in sub base complete all as specified and directed. |
| 39 | S & F Synthetic/Rubber (EPDM) mat Gym Flooring of minimum 25 mm thickness complete all as specified and approved by Engr -In-Charge. |
| 40 | Taking down carefully existing aluminum/copper surface/concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, lamp holder, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces in CM 1:3 of walls, floors, ceiling etc including painting if required to match up with existing surfaces complete all as specified and directed. Please Enable Macros to View BoQ information |
| 41 | Taking down carefully existing aluminum/copper surface/concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, lamp holder, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces in CM 1:3 of walls, floors, ceiling etc including painting if required to match up with existing surfaces complete all as specified and directed. Please Enable Macros to View BoQ information |