|
| 1 | Construction of Second Floor on A-Block of U.P. Transport Commissioner Office District- Lucknow (U.P.) |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. All kinds of soil. |
| 3 | 0.00 TO 1.50 MTR. |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M30 grade with minimum cement content of 350 kg /cum. (For R.C.C. Raft) |
| 7 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M30 grade with minimum cement content of 350 kg /cum. (For R.C.C. Raft) |
| 8 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. ln gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 9 | Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm thick with Grade-'l AAC blocks of density 551 to 650 kg/cum conforming to lS:2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. |
| 10 | Brick work withcommon brunt clayF.P.S. ( non modular ) bricks of class -designation 7.5 insuperstructure above plinth level up to floor V level in all shapes and sizes in cement mortor 1:6 ( 1 cement:6 coarse sand ) |
| 11 | Providing and laying 12 mm cement plaster of mix: 1:4 ( 1 cement:4 coarse sand ) |
| 12 | Providing and laying 12 mm cement plaster of mix: 1:4 ( 1 cement:4 coarse sand ) |
| 13 | Providing and laying 6 mm cement plaster 1:3 ( 1 cement:3 fine sand ) finished with a floating coat of neat cement of lime wash on top of walls when dry for bearing of R.C.C. slabs and beams: |
| 14 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm(For Outer surface) |
| 15 | ln gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 16 | Supply & Installation of Roof puff Panel with 50 mm |
| 17 | Providing ridges or hips of width 60 cm overall in plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with G.I. limpet and bitumen washers complete 0.80 mm thick with zinc coating not less than 275 gm/m² |
| 18 | (a) With ready mixed red oxide zink chromate primer of approved brand and manufacture on steel galvanised iron/steel works |
| 19 | (b) Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work. |
| 20 | Using R4 series with frame (115 mm & above) x (45 mm & above) & both glazed and flyscreen sash (44 mm & above) x (55 mm &above) with zinc alloy (zamak) powder coatedhandle on even/ glazed panel along with multipoint locking system. (Height above 1.8m) |
| 21 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. |
| 22 | Add for Mosquito jali (for uPVC Window) |
| 23 | Providing & Fixing Carpet Tiles Multi level loop 100% advance PP Fiber Gauge 1/12 Pile weight 680g/m pile heights 4mm/5mm Backing PVC with fiberglass Tile size 50cm by 50cm Usage commercial. |
| 24 | Skirting |
| 25 | Providing and laying Kota Stone slabs 20mm thick in risers of steps, skirting, laid on 12 mm Average thick cement mortar 1:3(1 Cement : 3Coarse sand) and jointed with Grey Cement slurry mixed with pigment to match the shade of this slab, including rubbing and polishing complete |
| 26 | Skirting |
| 27 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 1000x1000 mm |
| 28 | Skirting |
| 29 | Providing and laying vitrified wall tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, in skirting ,riser of steps, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 1000x1000 mm |
| 30 | Providing & Fixing of Laminated wooden flooring .All complete as per directions & instructions of Architect/Eng-In-Charge |
| 31 | Skirting |
| 32 | Profile |
| 33 | Quarter profile |
| 34 | Providing & Fixing of Engineered wooden flooring of multilayer eucalyptus hardwood core with having top layer thickness 1.5 mm and total thickness 14 mm. |
| 35 | Skirting |
| 36 | Profile |
| 37 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. (FLOORING) |
| 38 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 39 | Providing and fixing of Door Chaukhat made by 12 mm or 18 mm ply board with 4 mm veener and finished by PU Polish. All complete as per directions & instructions of Architect/Eng-In-Charge |
| 40 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces :Two coats. (For Internal wall surface & ceiling)(Asian Paint or equivalent) |
| 41 | Second Floor |
| 42 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 43 | Second Floor |
| 44 | Supply & Installation of Flush Door commercial quality conforming to I.S. 2202 part-1(1983) including fixing and adjustment of hinges,bolt locks with necessary screws to be supplied departmenly and 32 mm thickness. |
| 45 | Providing and fixing 150 mm bright finished floor door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. |
| 46 | Providing and fixing designer handles locks with with complete fittings as required |
| 47 | Providing and fixing Single or double leaf FRAMELESS GLASS DOOR - PIVOTED/Fix Glass Partition with 12mm thk toughened clear float glass of approved make. The rate to include cost for all necessary hardware, MS Work and floor springs along with holes / cutouts required for door patch fittings. All complete to the entire satisfaction of Engg in Charge/Architect. All Hardware INCLUSIVE as per design. |
| 48 | Providing and fixing of Exterior glass with Glazing(External Portion) with Aluminium Section 50X 50, Colour Coated Aluminium Section, Weather Proof Sillicon, Screw Pench, 5mm Thick Tinted Toughened Glass, Double Tape , Clamp Masking Tape etc . All complete to the entire satisfaction of Engg in Charge/Architect. All Hardware INCLUSIVE as per design. |
| 49 | Providing and fixing of Designer Metal ceiling. G.I /Aluminium open cell ceiling designed to lay onto 15 mm tee grid in size of 595x595 mm all system components ara made of roll formed hot dipped galvanized steel with zinc open cell ceiling tiles with color choice as specified All complete as per directions & instructions of Architect/Eng-In-Charge. |
| 50 | Providing and fixing of 12.5 mm thick tapered edge gypsum plain board conforming to IS:2095-(Part I):2011 (Board with BIS certification marks) |
| 51 | Grid Ceiling Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%, Thermal Conductivity k = 0.052 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizont al level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm |
| 52 | GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of GI sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 53 | Supply & Installation of Etching Film 6 mm Etching film developed by computer aided sign making system for decorative and functional graphics on class applied to glass with wet method. |
| 54 | Supply & Installation of Blinds with Translucent, blended double roller fabric with a Textile & subtle glass look. The Subte fold in the Closeal Stripes add a extra dimension of the fabric. |
| 55 | Providing and fixing of Panelling with 18 mm or 12 mm ply with ISI marked and finished with Designer laminate or leatherite Work on it. All complete as per directions & instructions of Architect/Eng-In-Charge |
| 56 | ELECTRICAL WORKS |
| 57 | POINT WIRING |
| 58 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc as required. |
| 59 | Group C |
| 60 | Wiring for group controlled(looped) light point/fan point/exhaust fan point/call bell point(without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper condutor single core cable in suface/recessed PVC conduit, and earthing the point with 1.5 sq. mm. FRLS PVC insulated copper conductor single core cable etc. as required. |
| 61 | Group C |
| 62 | Wiring for circuit/sub-main wiring along with earth wire with the following size of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 63 | 2X1.5 sqmm + 1x1.5 sqmm earth wire |
| 64 | 2X2.5 sqmm + 1x 2.5 sqmm earth wire |
| 65 | 2X4.0 sqmm + 1x 4.0 sqmm earth wire |
| 66 | 2X6.0 sqmm + 1x 6.0 sqmm earth wire |
| 67 | 4X6 sqmm + 2x 6.0 sqmm earth wire |
| 68 | 4X10 sqmm + 2x 6.0 sqmm earth wire |
| 69 | 4X16 sqmm + 2x 6.0 sqmm earth wire |
| 70 | Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in existing surface / recessed Steel/PVC conduit as required. |
| 71 | 3X2.5 sqmm |
| 72 | Supplying and drawing following pair 0.5 sqmm FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/recessed steel/PVC conduit as required. |
| 73 | 2 Pair |
| 74 | Supplying and drawing co-axial TV cable RG-6 graded, 0.7 mm solid copper conductor PE insulated,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 75 | Supply and fixing of following size of PVC conduit alongwith the accessories in recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required: |
| 76 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. |
| 77 | 5/6 A switch |
| 78 | 2 way 5/6 A switch |
| 79 | 15/16 A switch |
| 80 | 3 pin 5/6 A socket outlet |
| 81 | 6 pin 15/16 A socket outlet |
| 82 | Telephone socket outlet |
| 83 | TV antenna socket outlet |
| 84 | Bell Push |
| 85 | Supply and fixing of two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 86 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 87 | Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required. |
| 88 | 1 or 2 module(75mm X 75 mm ) |
| 89 | 3 module(100mm X 75 mm ) |
| 90 | 4 module(125mm X 75 mm ) |
| 91 | 6 module(200mm X 75 mm ) |
| 92 | 8 module(125mm X 125 mm ) |
| 93 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch,connection etc. as required. |
| 94 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,connection etc. as required. |
| 95 | Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box/wooden block including connectionetc. as required. |
| 96 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required. |
| 97 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. Including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 98 | Installation of exhaust fan in the existing opening, including making good the damage, connections, testing, commissioning etc. as required. |
| 99 | upto 450 mm sweep. |
| 100 | Extra for fixing the louvers / shutters complete with frame fro exhaust fans of all sizes. |
| 101 | Providing and fixing circular/Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/M.S. sheet box by means of 3.3 mm dia round headed screwed, one loc at the conrners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 102 | DISTRIBUTION BOARDS, MCB'S & ISOLATORS : |
| 103 | Providing & fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in in existing panel board including drilling holes in cubical panel, making connections, Ics=100% Icu and Operational Voltage 690V etc as required. |
| 104 | 100 A, 30 KA, FPMCCB |
| 105 | Supplying and fixing following way, Horizontal type three pole and neutral MCB distribution board, 415 volts on surface /recess complete with , tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators). |
| 106 | 6 way (4 + 18), Double door |
| 107 | 8 way (4 + 24), Double door |
| 108 | Supplying and fixing following way, surface/recess mounting,vertical type 415V, TPN MCB distribution board, on steel sheet, dust protected, duly power painted, inclusive of 200 A tinned copper busbar, common neutral link, earth bar, din bar, for mounting MCBs (But without MCBs and incomer) as required(Note:vertical type MCB TPDB is normally used where 3 phase outles are required.) |
| 109 | 8 way (4 + 24), Double door |
| 110 | Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' series, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 111 | Single Pole |
| 112 | Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required. |
| 113 | Supply and fixing following rating double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 114 | Providing and fixing M.V. danger notice plate of 200 mmx150 mm, made of mild steel, at least 2 mm thick, and viterous enameled white on both sides, and with incription in single red colour on front side as required. |
| 115 | Supplying and fixing Cable End Box(Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution borad, 415 Volts, on surface/recess, complete with testing and commissoning ect. as required. |
| 116 | For 6 way, Double Door TPNMCBDB |
| 117 | For 8 way, Double Door TPNMCBDB |
| 118 | Supply and installing of following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, jointed with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. |
| 119 | 150mm width x 50mm depth x 1.6mm thickness |
| 120 | 300mm width x 62.5mm depth x 2.0mm thickness |
| 121 | 450mm width x 62.5mm depth x 2.0mm thickness |
| 122 | Earthing with GI earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and salt as required. |
| 123 | Supplying and Laying of 25 mm X 3 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 124 | Providing & fixing 6 SWG dia G.I. on surface or in recess for loop earthing as required. |
| 125 | Brush Less Direct Current(BLDC) Motor with Remote |
| 126 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 127 | Supplying & making end termination with brass compression gland and aluminium lugs for the following size of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 128 | 4 X 16 sqmm. (28mm) |
| 129 | 3.5 X 300 sqmm. (70mm) |
| 130 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and refilling etc as required. |
| 131 | 100 mm Dia |
| 132 | 150 mm Dia |
| 133 | Supplying and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top as directed by Engineer-Incharge ,complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. |
| 134 | 16 sqmm 4 core |
| 135 | 300 sqmm 3.5 core |
| 136 | L.T. PANEL(LOC-SECOND FLOOR) |
| 137 | Supply, Installation, Testing and Commissioning of L.T. Panel vermin proof floor mounting, M.S. Channel Base with bottom and Fabricated out of 2.0/1.6 mm thik CRCA sheet steel painted with powder coated paint of shade as per the direction of Engineer In charge after proper sheet treatment peocess of sheet steel. The bus bar of panel shall be electrical grade high conductive alluminium alloy of appropriate cross section as per the rating. The main busbar shall be run throughout the panel of rating as main incomer rating. The Bus Bar shall be supported by non hygroscopic SMC/DMC Bus bar suports which shall be mounted on proper interval to ensure the bear the jerks of suport of short cuircuit of 50kA for panels having ACB as Incomer & 36 kA for panels having MCCB Incomers. Panel shall be constructed in fully Segregated Compartment Design for each Feeder as per 3b construction Format. The panel shall be completed in all respect as per IS 8623 Part 2 & 3. There shall be Seperated metering Component for Incomer metering and Outgoing metering. |
| 138 | All Incomer Feeders shall be provided with Multifunctional metering along with phase Indicating lights and other associated components such as CT control MCB Terminal Blocks etc. and all outgoing Feeders 100 A & above shall be provided with 3 phase Ammeter along with phase Indicating lights and other associates components such as CT control MCB Terminal Blocks etc. The feeder above shall be provided ac accommodated all measuring instrument shall be digital type & all indicating lights ahall be LED type. Wiring shall be done from 1100V Grade PVC Insulated copper flexible wire. All ACB shall be electricaly operated Draw out Type with microprosser based O/L, S/C & E/F Release off Breking/withstand capacity(ICU/ICs/Icw) 50 kA or more. All MCCB shall be thermal magnetics/microprossor with O/L & S/C protection along with required Spreders Extended rotary handle with pad locking facility of bracking capacity(ICU/ICS) 36 kA or more All MCB shall be Thermal 10kA 'C'Curve Cubical type switch board shall be Cat-A and B only. |
| 139 | Incoming : |
| 140 | 630 Amp. MCCB - 1No |
| 141 | Cat. B Panel Cubicale Type |
| 142 | Metering : |
| 143 | One (1) No. (0-500V) 96 x 96 Sqmm voltmeter with control fuse & selector switch. |
| 144 | One (1) No. (0-630A) 96 x 96 Sqmm CT operated Ammeter with selector switch, CTs etc. |
| 145 | One (1) Set of Phase Indication Lamp. |
| 146 | Bus Bar : |
| 147 | One (1) No.800 A, TPN aluminimum bus bar of suitable length. |
| 148 | Outgoing : |
| 149 | Phase indication lamps on each outgoing to be provided. |
| 150 | 400 Amp. 4P MCCB- 1 No. |
| 151 | 100 Amp. 4P MCCB- 2 No. |
| 152 | 63 Amp. 4P MCB- 5 No. |
| 153 | 40 Amp. 4P MCB- 2 No. |
| 154 | 125 Amp. 4P MCCB- 1 No. Spare |
| 155 | 63 Amp. 4P MCB- 1 No. Spare |
| 156 | 40 Amp. 4P MCB- 1 No. Spare |
| 157 | OR outgoing as per site requirment |
| 158 | With provision for meter space |
| 159 | A.C. PANEL- (LOC-TERRACE FLOOR) |
| 160 | Incoming : |
| 161 | 400 Amp. MCCB - 1No |
| 162 | Cat. B Panel Cubicale Type |
| 163 | Metering : |
| 164 | One (1) No. (0-500V) 96 x 96 Sqmm voltmeter with control fuse & selector switch. |
| 165 | One (1) No. (0-400A) 96 x 96 Sqmm CT operated Ammeter with selector switch, CTs etc. |
| 166 | One (1) Set of Phase Indication Lamp. |
| 167 | Bus Bar : |
| 168 | One (1) No.500 A, TPN aluminimum bus bar of suitable length. |
| 169 | Outgoing : |
| 170 | Phase indication lamps on each outgoing to be provided. |
| 171 | 160 Amp. 4P MCCB- 1 No. |
| 172 | 100 Amp. 4P MCCB- 2 No. |
| 173 | 63 Amp. 4P MCB- 4 No. |
| 174 | 63 Amp. 4P MCB- 1 No. Spare |
| 175 | 40 Amp. 4P MCB- 1 No. Spare |
| 176 | OR outgoing as per site requirment(AS/SLD)/VENDOR |
| 177 | Supply & Fixing of 1X17 W mirror light complete in all respects. Make-Philips or Eq |
| 178 | Supply of 15 W Deep Recessed Vito Panel complete in all respects. Make: Usha or Eq |
| 179 | Supply of 13 W Orrin LED COB Downlighters complete in all respects. Make: Usha or Eq |
| 180 | Supply of 1x36w Aster Pro above 4000K leumin indoor recess/Surface/Pendent mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing withextended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect.Make- Usha or Eq |
| 181 | Supply of 1x15w Aster Pro above 2000K leumin indoor recess/Surface/Pendent mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing withextended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect.Make- Usha or Eq |
| 182 | Supply of 6w Calalnto Pro Magnatic Light complete in all respects. Make: Usha or Eq |
| 183 | Supply of Calalnto Pro Accessories complete in all respects complete in all respects. Make: Usha or Eq |
| 184 | Supply of Decorative Light complete in all respects. Make: Usha or Eq |
| 185 | Supply of Decorative Bulb complete in all respects. Make: Usha or Eq |
| 186 | Supply of USB CHGR 1500mA 1M Type A MG AR complete in all respects. Make: Legrand or Eq |
| 187 | Supply of Arteor USB 1.5A Type C MG 1M complete in all respects. Make: Legrand or Eq |
| 188 | SITC of Flexible LED strip with wide viewing angle for good light distribution & IP 65,3000k, linkable and easy to install, complete with separate replaceable electronic driver complete in all respects(provide as option)Make: LedLum & eq. |
| 189 | Supply of Wall Fan AC 230/250 Volts, 50 Hz 50w 1350 rpm including nuts, bolts, mounting frame and other accessorieswith connections etc. complete as required.-Make: Havells-STANDARD -SUPER 5 LEAF-SW-12 & eq. |
| 190 | 300 mm sweep. |
| 191 | Supply of AC 230/250 Volts, 50 Hz 55w 1400 rpm exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required.Make: Havells-STANDARD -Refresh Air-SPS & eq. |
| 192 | 300mm sweep. |
| 193 | Supply and fixing following rateing four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 194 | 40 A,4P MCB-Bracking Capacity-10 kA, C-Curve-Make-Havells & eq. |
| 195 | 63 A,4P MCB-Bracking Capacity-10 kA, C-Curve-Make-Havells & eq. |
| 196 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 1 No. 16 A modular switch and 2 Nos. 6A modular socket & 1 No.6 pin 5/6 & 15/16 A modular socket outlet (recessed/ surface). ,connection etc. as required.-For Computer |
| 197 | S/f of 50 pair Junction Boxes for Floors and building with Krone connectors , with connection and punching of same |
| 198 | LIGHTING ARRESTER |
| 199 | Supply & fixing of level-I tested accordance with NFC-17-102 for advance triggering time 22 micro seconds, temperature with stand test of -40 to +120 degree centigrate, CE marked, short circuit test for 100KA etc. inculding the following: Make Liva/ESE(kalre)-50mtr.& eq. |
| 200 | SITC 5m GI mast with adaptor head and base plate for raising the lighting rod by 5 m above the surface to protected including insulator between lighting rod and GI mast. |
| 201 | SITC Copper cable 70 sqmm flexible copper single core multi-strand. |
| 202 | SITC 6 digits IP 67 lighting counter with hole for cable/strip LEC-D |
| 203 | SITC Eathing set(2 Nos.) consisting of copper bounded rod 17.2mm dia 10ft long 250 microns UL marked, 30kg earth enhancing chemical compound with resistivity of <0.1 Ohm-m NABL lab tested, clamp for connecting rod to cable/strip including civil work with pit cover complete. |
| 204 | SITC stay wire,lugs, U clam, base plate fastener, hook fasteners, Test link/clamp ect. As required complete. |
| 205 | FIRE PUMP HOUSE |
| 206 | POINT WIRING |
| 207 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc as required. |
| 208 | Group C |
| 209 | Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular type switch, modular plate, suitable G.I. box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc as required. |
| 210 | Wiring for circuit/sub-main wiring along with earth wire with the following size of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 211 | 2X1.5 sqmm + 1x1.5 sqmm earth wire |
| 212 | 2X4.0 sqmm + 1x 4.0 sqmm earth wire |
| 213 | 2X10.0 sqmm + 1x 6.0 sqmm earth wire |
| 214 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch,connection etc. as required. |
| 215 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,connection etc. as required. |
| 216 | Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box/wooden block including connectionetc. as required. |
| 217 | Installation of exhaust fan in the existing opening, including making good the damage, connections, testing, commissioning etc. as required. |
| 218 | upto 450 mm sweep. |
| 219 | Extra for fixing the louvers / shutters complete with frame fro exhaust fans of all sizes. |
| 220 | DISTRIBUTION BOARDS, MCB'S & ISOLATORS : |
| 221 | Supplying and fixing following way, single pole and neutral sheet steel, MCB distribution board, 240 V on surface /recess complete with , tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators). |
| 222 | 8 way, Double door |
| 223 | Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' series, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 224 | Single Pole |
| 225 | Double Pole |
| 226 | Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required. |
| 227 | Earthing with GI earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and salt as required. |
| 228 | Supplying and Laying of 25 mm X 3 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 229 | Providing & fixing 6 SWG dia G.I. on surface or in recess for loop earthing as required. |
| 230 | LED Batten light (System lumen efficancy >135 lm/Watt) |
| 231 | Supplying,installation, Testing & Commissioning of Batten light of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt,frequency 50/60 hz, Operating temp range-15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection, THD<10%, P.F. ≥0.95, IP20,CRI>80,UGR(Unified Glare Rating)<19,Flicker free(Flicker should be below 5%), life time(LED,Driver & electrical circuitary), of minimum 50000 Buring Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K/4000°K/5700°K/6000°K/6500°K(As per ANSI Bim.)SDCM(Standard Deviation Colour Matching)<3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards. |
| 232 | Manufactures Word Mark/Name Engraved/Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for testing facilities for LED fixtures. Complete in all respect i/c connection with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and earthing etc. as required with minimum 5 year OEM warranty. System lumen efficancy >135 lm/watt output. LM79 & LM 80 test report from NABL lab for all testing required for LED fictures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in Charge as per requirement.(Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). |
| 233 | Powder coated die cast/Extruded aluminum Body (Thickness ≥1.20mm) |
| 234 | 18-22 watt |
| 235 | Supply and fixing of water tight oblong 10 Watt LED Bulkhead luminaire having pressure die cast housing with driver set confirming to IP 65 and above Protection. IK 08, High purity/transmisivity UV stabilized Non yellowish diffuser/refelctor for uniform light distribution, detachable driver set, open and short circuit protection, suitable for 24 Hr Continious Operation, complete in all respects. |
| 236 | 1100 system lumens,>110 lm/W, PF>.95, THD<10%, CRI>70, with 3 years Warrantee.CAT. - AA |
| 237 | Supply of AC 230/250 Volts, 50 Hz 55w 1400 rpm exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required.Make: Havells-STANDARD -Refresh Air-SPS |
| 238 | 300mm sweep. |
| 239 | DG Set |
| 240 | Earthing with GI earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and salt as required. |
| 241 | Supplying and Laying of 25 mm X 3 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 242 | Supplying & making end termination with brass compression gland and aluminium lugs for the following size of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 243 | 3.5 X 300 sqmm. (70mm) |
| 244 | Supply, installation, Testing & Commissioning of 'Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements Complete as per CPWD specifications, should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings: (A) Diesel Engine:Turbocharged Diesel engine 4 stroke water cooled, multi cylinder, dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50% RH & at 1000 Meter MSL , capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be with Electronic governor, Dry type Air filter with service indicator, first filling of engine fuel (after commissioning) lubricating Oil, Coolant and other consumables complete with all the required accessories, |
| 245 | the Electronic governor shall be as per ISO 8528.The engine shall comply to the latest CPCB norms (CPCB IV + or better) and Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as perCPWD specifications.(B) Engine mounted Instrument Panel fitted with and having digital display for following:(i) Start-stop switch with key(ii) Water temperature indication(iii) Lubrication oil pressure indication(iv) Lubrication oil temperature indication(v) Battery charging indication and Voltage indication(vi) RPM indication(vii) Over speed indication(viii) Low lubricantion Oil trip indication(ix) Engine Running Hours indication(x) Fuel Level (C) Alternator:Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1000 Meter MSL. The alternator shall be having Screen Protected Drip Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically balanced rotor, capable of taking 10% over loading for one hour after 12 hours of continuous operation, self cooled,self-excited and self-regulated through AVR conforming to IS13364(Part 2)/IS: 4722/BS 2613 suitable for tropical conditions and with class- H insulation. |
| 246 | (D) Base Frame & Foundation:Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangementas per recommendations of manufacturer. (E) FUEL TANK:Daily service fuel tank of suitable liters capacity as per CPWD Specifications, fabricated out of 3 mm thick M.S. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class 'C' pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications.(F) Exhaust System:Dry exhaust manifold with hospital type exhaust silencer and catalytic convertor. |
| 247 | (G) Starting System:12V/24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable numbers of batteries (180 AH capacity lead acid SMF type) as required as per specifications. The battery shall be housed inside the acoustic enclosure of DG Set. (H) Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere and the temperature rise inside the enclosure, noise level outside enclosure. The acoustic enclosure should be suitable for cable connection/connection through bus-trunking. Such arrangements on acoustic enclosure should be water proof & dust-proof conforming to IP-65 protection. The enclosure shall be as per CPCB IV + or better norms etc. and as per CPWD specifications. |
| 248 | (I) AMF Panel:Free standing floor mounted IP 42 automatic mains failure control panel including auto by-pass, suitable for KVA as below for silent type DG set complete with relays, timers, set of CTs for metering & protection and energy analyser to indicate currents, phase and line voltages, frequency, power factor, KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA (Phase & Total), KW & provision for overload, short circuit, restricted earth fault, under frequency, power (aluminum) and control (copper ) cabling of suitable size upto 15 meter between AMF panel, LT Panel and DG Set including connection interconnection etc. as required, all complete and inter locking and communication/ Ethernet /RS485/SNMP port open protocol for BMS integration including suitable software, the panel shall be of DG Set OEM make etc. as per approved by Engineering in charge and including the following:1. Suitable numbers and appropriate capacity 4 pole motorised electrically operated draw out with cradle type 3 position ACB/ MCCB with electronic release for O/C & E/F and shunt trip.2. Auto/Manual/Test/Off selector switch3. Protection for under and over voltage phase reversal (2 nos Over voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage relay). 4. 3 Sets of current transformers 15 P 10 accuracy for protection and 15 VA class-I for metering5. Energy analyser unit to indicate current, Voltage( L-N & L-L), kW, kVA (Phase & Total), Frequency, KWH, PF. |
| 249 | 6. LED Indicating lamps for load on mains and load on set.7. Fuse/ MCB for instruments.8. Battery charger, complete with transformer/ rectifier, D.C. voltmeter and ammeter, selector switch for trickle, off and boost and current adjustment.9. Main supply failure monitor.10. Supply failure timer.11. Restoration timer12. Control unit with three impulse automatic engine start/stop and failure to start lockout.13. Impulse counter with locking and reset facility.14. ON/OFF/Control circuit switch with indicator |
| 250 | 15. Audio/Video annunciation for(i) High water temperature(ii) Low lubricating oil pressure(iii) Engine over speed(iv) Engine fails to start(v) Full load/maximum load warning16. Protection for over/under Frequency, Loss of AC sensing, Over Current, Unbalancing load with suitable number of relays and accessories17. Maintenance notification based on Engine Run Hour & due date.18. Load Management through PLC to achieve auto opening and closing of incomer breakers, bus coupler switching of essential panel , interlocking providing signal to AMF Panel for load status and AMF shall give command to DG Set to auto start / auto stop depending upon load status and requirement etc. and necessary hardware and software required to perform the operation shall be provided by the contractor including all control wiring. |
| 251 | 250 KVA |
| 252 | Supplying and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top as directed by Engineer-Incharge ,complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. |
| 253 | 300 sqmm 3.5 core |
| 254 | (U.P.S.) |
| 255 | Online UPS- Input supply: Three Phase, Output supply: Three Phase |
| 256 | Supplying, installation, Testing & Commissioning of of following capacity at full load (Unity Power Factor) at operating temperature 0 to 40 deg C, Relative humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot swappable (allow for the replacement or addition of battery modules without shutting down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of moduels requird for rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch alongwith provision for manual bypass, suitable isolation transformer for additional protection against neutral faults etc. |
| 257 | UPS shall have inbuilt phase sequence correction. The UPS systems offered are to be of the latest technology with Digital Control Microprocessor based for reliable operation using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The quality of design, manufacturing and inspection process should confirm to the relevant Inter- national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while operating on battery mode and delivering quality power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50 %load. (The required LC ( inductor (L) and a capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to be included to limit the input power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall bekva rating x 1 ), however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non condensing, noise level less than 60db at 1 meter distance, protections: Input Under voltage over voltage, abnormal out voltage, battery over charging, output over current, short circuit protection, battery deep discharge protection, 10KV surge. UPS must comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI)-type UPS. |
| 258 | Communication RS232/RS485/SNMP port open protocol for BMS integration, all hardware & software for iOT Communication as per approved by Engineering in charge. Required battery racks and interconnecting copper conductor cables of suitable size and connectors and all required accoseries are inclusive of the cost). This system must provide a means for logging and alarming of all monitored points plus email notification. Forced air-cooling with integral inbuilt fans with redundancy (if one fan fail UPS should be able to handle at least 80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in compliance IEC 62040- 1,2 & 3, IS: 16242 and CPWD Specification. |
| 259 | Display Panel (minimum) (In-build 5 inch or more LC Display / LED ) to display : a) Input: Voltage, current, Frequency. b) Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current. d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage. f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On LCD/LED): UPS should capture and display up to 3000 events like: Over temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit / Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data: No. of power failures / Transfers to Bypass / Total Running time, etc. i) Mains Mode of Operation /Battery Mode of Operation / Bypass feeding the load / UPS Fault /Battery charging and discharging, overload, battery voltage and battery capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS Overload, Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery Over, Under Voltage, Over Load and short circuit, Over Temperature. The UPS should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc. |
| 260 | 20 KVA (Each Power module shall be ≤10 KVA) |
| 261 | PLUMBING WORKS |
| 262 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 263 | Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth. |
| 264 | Granite Stone of approved shade |
| 265 | Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge. |
| 266 | 15mm nominal bore |
| 267 | Providing & fixing 32 # G.I. Pipes spout including cutting & making good the walls etc. |
| 268 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. |
| 269 | internal work -Exposed on wall |
| 270 | 25mm dia nominal outer dia pipes |
| 271 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. |
| 272 | Concealed work including cutting chases and making good the walls etc. |
| 273 | 15mm dia nominal outer dia pipes |
| 274 | 20mm dia nominal outer dia pipes |
| 275 | 25mm dia nominal outer dia pipes |
| 276 | Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 |
| 277 | 15mm nominal bore |
| 278 | Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. |
| 279 | 15mm nominal bore |
| 280 | Providing & fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 281 | Providing and fixing brass stop cock of approved quality. |
| 282 | 20 mm nominal bore |
| 283 | Providing and fixing gun metal gate valve with wheel of approved quality. |
| 284 | 25mm dia nominal bore |
| 285 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank. IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 286 | Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required, |
| 287 | in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. |
| 288 | Pipes, cables etc. exceeding 80mm dia. But not exceeding 300 mm dia. |
| 289 | Providing and laying Non pressure NP2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. |
| 290 | 150mm dia. R.C.C. pipe |
| 291 | 250mm dia. R.C.C. pipe |
| 292 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of S.W./R.C.C. pipes including bed concrete as per standard design |
| 293 | 150mm diameter R.C.C. Pipe |
| 294 | 250mm diameter R.C.C. Pipe |
| 295 | Providing and fixing square mouth S.W. Gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 Kg and frame to be not less than 2.70 Kg as per standard design: |
| 296 | 150 x 100 mm. size P type |
| 297 | With Sewer bricks conforming to IS : 4885 |
| 298 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design |
| 299 | Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). |
| 300 | With FPS bricks of class designation 75 |
| 301 | (i) For Sewer Line |
| 302 | Extra for depth of man hole size 90x80 cm |
| 303 | Inside size 90x120 cm & 90 cm deep including C.I. cover with frame (medium duty) total wt. of cover & frame to be not less than 116 Kg (wt. of cover 58 Kg & wt. of frame 58 Kg. |
| 304 | Extra for depth of man hole size 90x120 cm |
| 305 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm nominal size) as per standard design |
| 306 | With 20x20 mm square bar |
| 307 | Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before with supply and cost of other fIttlings such as elbow,bend,tee and y-tee,Cowel including supply of all marerial labour and T&P. Required for proper completion of work. |
| 308 | 90 mm O.D. |
| 309 | 110 mm O.D. |
| 310 | Supply and fixing of UPVC S.W.R. pipe nahni trap size 100x75,110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali. |
| 311 | Supply and fixing of UPVC S.W.R. Cowel confirming to IS-14735. |
| 312 | Size 110 mm |
| 313 | Providing and fixing rimless wall hung water closet including PP seat cover, Hinges, Accessories and c, nuts, bolts and gasket etc. complete. -Make Cera or Eq |
| 314 | Providing and fixing Cistern and cistern fitting, nuts, bolts and gasket etc. complete. -Make Cera or Eq |
| 315 | Providing and fixing Control plate, nuts, bolts and gasket etc. complete. -Make Cera or Eq |
| 316 | Providing and fixing wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including Pillar cock, painting of fittings and brackets, cutting and making good the walls wherever require:-Make cera .& eq. |
| 317 | Providing and fixing Basin Mixer with brackets, cutting and making good the walls wherever require:--Make Cera or Eq |
| 318 | Providing and fixing Single liver Waste Coupling :--Make Cera or Eq |
| 319 | Providing and fixing white vitreous china battery based infrared sensor operated urinal, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Make-Duravit & eq. |
| 320 | Providing & fixing C.P. brass HG angle valve E-E DN15xDN15-15mm-Make- Cera or Eq |
| 321 | Providing and fixing CP Brass 32 mm size Bottal Trap-Make- Cera or Eq |
| 322 | Providing & Fixing C.P.brass Towel ring-Make--Make Cera or Eq |
| 323 | Providing and fixing C.P. brass Toilet paper holder-Make--Make Cera or Eq |
| 324 | Providing & Fixing C.P. Brass Health Faucet -Make-Make Cera or Eq |
| 325 | Providing & fixing C.P. Soap Dispenser -Make--Make Cera or Eq |
| 326 | EXTERNAL WATER SUPPLY SYSTEM |
| 327 | Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required, |
| 328 | in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. |
| 329 | Pipes, cables etc. not exceeding 80mm dia. |
| 330 | Provding and fixing gun metal non return valve of approved quality (screwed end) |
| 331 | 80 mm nominal bore |
| 332 | Vertical |
| 333 | Providing & fixing G.I. pipes complete with G.I. fittings including tenching and refilling etc. |
| 334 | External work |
| 335 | 50mm nominal bore. |
| 336 | 80mm nominal bore. |
| 337 | Providing & fixing sand of grading zone V or coaser grade alround the G.I. Pipes in external work. |
| 338 | 50 mm diameter pipe |
| 339 | 80 mm diameter pipe |
| 340 | Providing and fixing gate valve (with cap complete with bolts, nuts, rubber insertion etc. |
| 341 | 50 mm nominal bore |
| 342 | 80 mm nominal bore |
| 343 | Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand ) for sluice valve, with C.I. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : |
| 344 | With F.P.S. bricks |
| 345 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : |
| 346 | 25 to 40 mm dia nominal bore |
| 347 | 50 to 80 mm dia nominal bore |
| 348 | PUMPS & EQUIPMENT |
| 349 | Supply, assembly, erection, testing and commissioning of SS / CI submersible non-clog pumps, suitable to handle Pump room drainage having the following capacities with vortex impeller / grinder type, complete with 3 phase squirrel cage submersible motor of required HP for 415 ± 10% volts, 3 phase, 50 Hz. A.C. supply cooled by surrounding liquid, submersible cable upto main panel within the plant room, dry running preventor, G.I. guide pulling chain, all the necessary piping and accessories, valves, delivery header etc. as required complete in all respects. The rate will include electrical panel with cyclic operation as supplied by the manufacturers).(For U G Tank Pump room drainage). |
| 350 | Flow Rate : 300 LPM |
| 351 | 1Set = 2 Nos. Pumps (1 Working + 1 standby ) with control panel. |
| 352 | Head in Mtrs. : 15-18 Mtr |
| 353 | Supply, Installation, testing & commissioning of package type skid mounted hydropneumatic system set(Horizontal / Vertical inline single/multistage centrifugal pumping set) complete. The rate shall include the cost of electrical panel and piping work complete. |
| 354 | Domestic Water Supply pumps : |
| 355 | Pump Capacity 15m3/h.(Each Pump) at 50m head (1 Working + 1 Stand-by) Domestic Water Supply |
| 356 | Supplying, assembly, erection, testing and commissioning of magnetic level sensors and controllers, CPVC probe tube, PP actuating float and all other equipment required for the performance of the system to the satisfaction of the engineer in charge complete including providing and fixing wiring from control junction box near the UG tank to probes of required length, interconnection wiring between level controller and the concerned contactor in the starter panel as required. The level controller will perform the following functions. |
| 357 | To switch on the pumps (including raw water pumps (Domestic Water Treatment, Softening Plant etc.) when the level of water in the supply water tank is low and to cut off the pump when the level in the receiving water tank is high and switch off the pumps when the level of water in the supply water tank is low. |
| 358 | To indicate 5 levels of water in all tanks through a control panel with LEDs |
| 359 | To start the pumps in a cyclic order. |
| 360 | The system shall be complete to ensure automatic quotation of pump in accordance to water level in respective tanks. |
| 361 | The Contractor will include all the under ground and over head tanks and all the pumps as required for level control in this item |
| 362 | Providing & fixing in position Vane Type mechanical water flow meter for following pipe size |
| 363 | 50 mm dia |
| 364 | Fabrication, Supplying, Installation, Testing & Commissioning of Electrical Plumbing Motor Control Panel of cubical construction, floor mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalized with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with solid aluminium strip / single core PVC insulated FRLS copper conductor cable, having suitable mountings for switchgears and accessories and internal control & power wiring with suitable rating PVC insulated FRLS copper conductor, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42 with 500 Amp aluminium bus bar etc complete as required with required incoming and out goings, cable, cable trays etc. |
| 365 | FIRE FIGHTING WORK |
| 366 | (A) Supplying, Installation, Testing & Commissioning of Electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required:(Terrace Pump) |
| 367 | (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal confirming to IS 1520. |
| 368 | (C) Suitable HP Squirrel cage indution motor, TEFC type suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, confirming to IS-325. |
| 369 | (D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. |
| 370 | (E) Suitable cement concrete foundation duly plastered with anti vibration pads. |
| 371 | 450 lpm at 35 m head |
| 372 | Providing, laying, testing & Commissioning of 'C' class heavy duty MS pipe confirming to IS 3589/IS1239 inculding welding, fittings like elbows,tees, langes,tapers,nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of syntetic enamel paint of required shade complete as required: |
| 373 | 25 mm dia |
| 374 | 100 mm dia |
| 375 | Supplying & fixing single headed internal yard hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel, ISI marked, confirming to IS 5290(type A) with blank Gunmetal/Stainless Steel cap and chain as required: |
| 376 | Single headed Gunmetal |
| 377 | Supplying, fixing, testing & commission of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confirming to IS 13095 of following sizes as required: |
| 378 | 100 mm dia |
| 379 | Supplying & fixing orifice plate made out of 6 mm thick stainless steel(grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required: |
| 380 | Providing, installation, testing and commission of non-return valve of following sizes confirming to IS: 5312 complete with rubber gaskets GI bolts, nuts, washers etc as required 100 mm dia: |
| 381 | Supplying & fixing 63 mm dia, 15m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. confirming to IS 636(type-A) as required: |
| 382 | Gun Metal |
| 383 | Supplying & fixing First-aid hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following as required. |
| 384 | 20 mm nominal internal dia water hose thermoplastic(Textile reinforced) type-2 as per IS:12585 |
| 385 | 20 mm nominal internal dia gun metal globe valve & nozzle. |
| 386 | Drum and brackets for fixing the equipments on wall. |
| 387 | Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. |
| 388 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle confirming to IS:903 suitable for instantaneous connection to interconnect hos pipe coupling as required. |
| 389 | Gun Metal |
| 390 | Providing & fixing of pressure switch in M.S. pipe line including connection etc as required. |
| 391 | Supplying & fixing air vessel made out of 250 mm dia,8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. |
| 392 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank. IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 393 | FIRE DETECTION & ALARM SYSTEM |
| 394 | Supplying, installation, testing & commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices(including detector) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memroy(EPROM), power supply(230+-5% V, 50hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall to have facility to connect printer to printout log and facikity to seamless integration with analog/digital voice evacuation system(which is part of the schedule of work under SH:PA system) and shall be complete with all accessories. The panel shall be compatible for IBMS system with open protocol BACnet/Modbus over IP complete as per specifications. |
| 395 | Two Loop Panel |
| 396 | Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required. |
| 397 | Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. |
| 398 | Supplying, installation, testing & commissioning responce indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required. |
| 399 | Supplying, installation, testing & commissioning of fault isolator complete with base as required. |
| 400 | Supplying, installation, testing & commissioning of addressable fire control moudle complete as required. |
| 401 | Supplying, installation, testing & commissioning of addressable phone control moudle complete as required. |
| 402 | Supplying, installation, testing & commissioning of addressable manual call point complete as required. |
| 403 | Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. |
| 404 | Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required. |
| 405 | Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. |
| 406 | Supplying & laying of 2X1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH ineer bedding,, steel wire armouring & LSZH outer sheath complete as required. |
| 407 | Supplying & laying 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required. |
| 408 | Supply and fixing of following sizes of steel conduit along with the accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required: |
| 409 | FIRE SPRINKLER SYSTEM |
| 410 | Providing, laying, testing & Commissioning of 'C' class heavy duty MS pipe confirming to IS 3589/IS1239 inculding welding, fittings like elbows,tees, langes,tapers,nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of syntetic enamel paint of required shade complete as required: |
| 411 | 25 mm dia |
| 412 | 32 mm dia |
| 413 | 40 mm dia |
| 414 | 50 mm dia |
| 415 | 80 mm dia |
| 416 | 100 mm dia |
| 417 | 150 mm dia |
| 418 | Supplying, fixing, testing & commission of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confirming to IS 13095 of following sizes as required: |
| 419 | 80 mm dia |
| 420 | 100 mm dia |
| 421 | Providing, fixing, testing and commission of 15 mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories: |
| 422 | Pendent Sprinkler |
| 423 | Providing & fixing of flow switch in following M.S. pipe including connection etc as required. |
| 424 | 100 mm dia |
| 425 | Supplying, installation, testing and commission of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI(Burst) with branch line(Inlet) 25mm NPT male thread to sprinkler head(Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required |
| 426 | 1200 mm |
| 427 | Providing, installation, testing and commission of adjustable rosette plate for 15mm dia in white finish UL listed or FM approved complete as required. |
| 428 | FIRE FIGHTING SYSTEM(EXTERNAL) |
| 429 | Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. Pipes, cables etc. not exceeding 80mm dia. |
| 430 | Pipes, cables etc. exceeding 80mm dia. But not exceeding 300 mm dia. |
| 431 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 432 | 150 mm dia |
| 433 | 100 mm dia |
| 434 | 80 mm dia |
| 435 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 436 | 80 mm dia |
| 437 | 100 mm dia |
| 438 | Supplying & fixing single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, confirming to IS 5290(type A) with blank Gunmetal/Stainless Steel cap and chain as required: Single headed Gunmetal |
| 439 | Supplying, fixing, testing & commission of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confirming to IS 13095 of following sizes as required: |
| 440 | 80 mm dia |
| 441 | 100 mm dia |
| 442 | Providing, installation, testing and commission of non-return valve of following sizes confirming to IS: 5312 complete with rubber gaskets GI bolts, nuts, washers etc as required: 100 mm dia |
| 443 | Supplying & fixing 63 mm dia, 15m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. confirming to IS 636(type-A) as required: Gun Metal |
| 444 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle confirming to IS:903 suitable for instantaneous connection to interconnect hos pipe coupling as required. Gun Metal |
| 445 | Supplying & fixing of Fire brigade connection of cast iron body with gun metal male instantaneous inlet coupling complete with cap and chain as required. for suitable dia MS pipe connection conforming to IS 904 as required: |
| 446 | 2 way-100 mm dia M.S. Pipe |
| 447 | 4 way-150 mm dia M.S. Pipe |
| 448 | Supply & fixing of fire extinguisher 6.00 kg. capacity(ISI Marked IS:15683 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 449 | Supply & fixing of CO2 type fire extinguisher, 4.5 kg. capacity(ISI Marked IS:2878 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 450 | Providing/Fixing of Fire Hose cabinet box made out of 18 gauge MS sheet including two coats of post office red paint over one coat of primer with 4 mm, thick glass door in front painted “FIRE” in red luminous paint. The size of the box should be 750 mm X 600 mm X 250 mm size capable of accommodating a pair of hose with coupling and nozzle. The box should be floor mounted type with railway coach lock arrangement and lever for opening the door after breaking the glass complete. Make : Standard/Lifeguard or EQ. |
| 451 | Providing & Fixing of 1.6 mm thick M.S / Door Frame, Door capable of accommodating fire Hose Reel, Landing Valve, Hose Pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering).(Liasioing with civil contractor for making Recessed type mansoary box (by civil contractor). |
| 452 | Supplying and fixing of Self Glow Exit signage for stairs and exits made out from not less than 4 mm of transparent acrylic sheet of 300 x 150 mm size with self illuminated plastic words of 100 mm height suspended from ceiling by means of M.S. chain or fixed of the walls as required and as directed at site..(MAKE : Agni Suraksha (ASES) / Securiton-aka /System Sensor) |
| 453 | Signage with the following text\\"IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTERWISE\\" of 1.25 cm height letters in red with white back ground. The size of the board shall be 25 cmx30 cm and shall be fixed at the height of 2 mtrs. From finished floor near manual call points. |
| 454 | Floor identification signage(ie, GROUND FLOOR, etc) at the each stair & LIft enclosure on every floor, indicating the floor number in words, lettering size shall be 7.5 cm with contrasting colour from back ground shall be 15 cmx60 cm. |
| 455 | Supplying and fixing in position of Fire Escape Route Plan A2 size. |
| 456 | Supplying and fixing of Fire man axe. Make :- Agni Suraksha (ASES) or EQ |
| 457 | Supply, Installation, Testing and Commissioning of electronic siren with suitable audible range of 1 k.m. approximately 4 watt.complete in all respects. Make :- Agni Suraksha (ASES) or EQ. |
| 458 | Providing/Fixing of cubical type floor mounted Fire pump control panel fabricated from 16 G M.S. sheet duly powder coated finish of approved shade and comprising of : Incomer:-a) 63 amp 4 Pole MCCB, 50Hz with breaking capacity 10KW.b)One Volt meter (0-500 V) with selector switch.c) Ammeter (0-63 Amps.) with selector switch & CTs. - 1 Setd) Set of 3 phase indication lamps - 1 Set e) Set of Al bus bar 200 Amp 4 strip - 1 Set f) Selector switch for local/remote, auto/manual/off operation ON/OFF indication lamp etc. - 1 Set |
| 459 | Outgoing:-1 x 63 Amps FP MCCB (25 KA) with Suitable HP fully automatic Star/Delta Starter with over load protection, current sensing type single phase preventor complete with all accessories and internal wiring required for automatic operation. |
| 460 | ANNUCIATION PANEL |
| 461 | Supply installation testing and commissoning of Annuciation Panel made out of not less than 1.6 mm thick CRCA powder coated sheet of approved colour with locking arrangement, audio and visual indication of fault and operation of sprinkler, system monitoring including providing and fixing the following connections and interconnections etc complete as required. The panel should be Microprocessor type.a. Monitoring 10 nos. of flow switchesb. Monitoring the open circuit, short circuit and earth fault in control cable between panel and floe switches.c. Battery charger tricle cum boost to take complete load of annunciation panel complete with indication of low battery voltage, mains failure and other accessories including providing and fixing of 2 nos 12V 24 AH each sealed maintenance free batteries.d. Audible Alarm |
| 462 | FIRE PUMP HOUSE |
| 463 | Supplying, Installation, Testing & Commissioning of Electric driven Main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required: |
| 464 | (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal confirming to IS 1520. |
| 465 | (b) Suitable HP Squirrel cage indution motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, confirming to IS-325. |
| 466 | (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. |
| 467 | (d) Suitable cement concrete foundation duly plastered with anti vibration pads. |
| 468 | 1620 lpm at 70 m head |
| 469 | Note: The head of the pump is selected in a manner so as to give a minimum 3.5kgf/cm2 pressure at the highest/farthest point. |
| 470 | Supplying, Installation, Testing & Commissioning of Diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required:(Diesel Driven Pump) |
| 471 | (a) Horizontal type, multistage, centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal confirming to IS 1520. |
| 472 | (b) Suitable HP 1500 RPM, water cooled with radiator, diesel engine confirming to relevant IS standard complete with auto starting mechanism,12/24 volts electric starting equipment, disel tank, exhaust pipe extended upto 10m outside pump house duly insulated with 50mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, pianted with post office red colour etc. as required. |
| 473 | (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. |
| 474 | (d) Suitable cement concrete foundation duly plastered with anti vibration pads. |
| 475 | 1620 lpm at 70 m head |
| 476 | Note: The head of the pump is selected in a manner so as to give a minimum 3.5kgf/cm2 pressure at the highest/farthest point. |
| 477 | Supplying, Installation, Testing & Commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required:(Jockey Pump) |
| 478 | (a) Horizontal type, multistage, centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal confirming to IS 1520. |
| 479 | (b) Suitable HP Squirrel cage indution motor, TEFC type suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 class protection for enclosure, horizontal foot mounted type with Class-'F' insulation, confirming to IS-325. |
| 480 | (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. |
| 481 | (d) Suitable cement concrete foundation duly plastered with anti vibration pads. |
| 482 | 180 lpm at 70 m head |
| 483 | Fabrication, supply, Installation, Testing & Commissioning of Electrical control panel of cubical construction. Floor mounted type, fabricated out of 2 mm thick CRCA sheet, compartmentalised with hinged locable doors,dust and vermin proof, powder coated of approved shade after tank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mounings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump,pressurisation pump & diesel pump set complete in coming and outgoings, suitable for operation on 415V, 3 phase, 50 Hz Ac Supply with enclosure protection class IP 42 as required: |
| 484 | INCOMING |
| 485 | 250A, 50kA 4 Pole MCCB, Ics=100% Icu rating |
| 486 | Digital Voltmeter 0-500V with seletor switch |
| 487 | Digital Ammeter 0-250 Awith seletor switch & CTs etc. |
| 488 | LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps |
| 489 | Set of Copper Bus Bar 300A |
| 490 | OUTGOING |
| 491 | (Note: All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps) |
| 492 | Main Fire Pump |
| 493 | 125A, 50KA 4 Pole MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 60 HP pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, seletor switch for local/remote, auto/manual/OFF operation. |
| 494 | Jockey Pump |
| 495 | 63A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, seletor switch for local/remote, auto/manual/OFF operation. |
| 496 | DIESEL ENGINE CONTROL |
| 497 | Control for diesel engine comprising- |
| 498 | Automatic/manual selector switch & 3 attempts staring device, timers and relay as required, push buttons, start/stop in manual mode. |
| 499 | Indicating lamp for high/Low Lub. Oil pressure, High water Temp and Engine on indication. |
| 500 | Battery charger suitable for 12V/24 V DC with boost and trickle seletor switch, 0-30 V DC coil meter, and 0-20 A DC Ammeter. |
| 501 | All standard relays and accessories for automatic operation of diesel engine. |
| 502 | System Controller |
| 503 | Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers, Sensors, annuciation window for fault indicaion, complete as per specification. |
| 504 | Providing, laying, testing & Commissioning of 'C' class heavy duty MS pipe confirming to IS 3589/IS1239 inculding welding, fittings like elbows,tees, langes,tapers,nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of syntetic enamel paint of required shade complete as required: |
| 505 | 80 mm dia |
| 506 | 100 mm dia |
| 507 | 150 mm dia |
| 508 | 200 mm dia(wall thickness 6.3 mm) |
| 509 | Supplying, fixing, testing & commission of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confirming to IS 13095 of following sizes as required: |
| 510 | 80 mm dia |
| 511 | 100 mm dia |
| 512 | 150 mm dia |
| 513 | 200 mm dia |
| 514 | Providing, installation, testing and commission of non-return valve of following sizes confirming to IS: 5312 complete with rubber gaskets GI bolts, nuts, washers etc as required: |
| 515 | 80 mm dia |
| 516 | 100 mm dia |
| 517 | 150 mm dia |
| 518 | 200 mm dia |
| 519 | Providing, installation, testing and commission of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel(grade 304) sheet with 3 mm dia holes with stainless steel flange. |
| 520 | 150 mm dia |
| 521 | 200 mm dia |
| 522 | Providing and fixing in position the industrial type Pressure Gauges with gun metal / brass valves complete as required |
| 523 | Supplying & fixing of Fire brigade connection of cast iron body with gun metal male instantaneous inlet coupling complete with cap and chain as required. for suitable dia MS pipe connection conforming to IS 904 as required: |
| 524 | 4 way-150 mm dia M.S. Pipe |
| 525 | Supplying & fixing air vessel made out of 250 mm dia,8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. |
| 526 | Providing & fixing of pressure switch in M.S. pipe line including connection etc as required. |
| 527 | Providing, fixing, testing and commission of installation control valve of cost iron body, brass/bronze working parts comprising of motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, stainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwoing sizes as required : |
| 528 | 150 mm dia |
| 529 | Earthing with GI earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and salt as required. |
| 530 | Supplying and Laying of 25 mm X 3 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 531 | Supply and installing of following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, jointed with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. |
| 532 | 300mm width x 62.5mm depth x 2.0mm thickness |
| 533 | 450mm width x 62.5mm depth x 2.0mm thickness |
| 534 | Supply & fixing of fire extinguisher, ABC Type 6.00 kg. capacity(ISI Marked IS:15683 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 535 | Supply & fixing of CO2 type fire extinguisher, 4.5 kg. capacity(ISI Marked IS:2878 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 536 | Supplying and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top as directed by Engineer-Incharge ,complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. |
| 537 | 16 sqmm 4 core |
| 538 | 185 sqmm 3.5 core |
| 539 | Providing & fixing gun-metal fire brigade suction hose coupling-150 mm (draw-out connection) with nut for female coupling as per IS: 902-1992 (Reconfirmed 2007) Complete.Make : Standard/Lifeguard or EQ. |
| 540 | Providing,fixing,testing & commissioning of M.S.class 'C' diesel pump exhaust pipe including all fittings like bends,tee,clamps/structural steel support of suitable dia for the engine.The insulation of the exhaust pipe shall be carried out with rock wool with specific gravity of 100kg/cm2 and cladded with 22 gauge aluminium sheet complete with all fittings & accessories.Make: Tata/Zindal. |
| 541 | 100 mm dia |
| 542 | Providing & fixing cast iron Air Release Valve of 25 mm dia including 25 mm dia Ball valve with fittings etc. as per the requirement. |
| 543 | [EPBAX SYSTEM] |
| 544 | Supply of Digital EPABX System 2 Trunk ; 2 Digita Port ; 40 Extensions Expandable Upto 80 Port |
| 545 | Supply of Digital Key Telephone |
| 546 | Supply of Telephone Set with Caller ID |
| 547 | Supply of 100 Pair MDF Box |
| 548 | KRONE 10 Pair |
| 549 | Telephone Cable 2 Pair |
| 550 | PVC Conduict / Pipe 25mm |
| 551 | Cabling Charges (In Running Meters) |
| 552 | Installation, Programming, Testing & Commissioning of EPABX Hardwares (Including EPABX Machine + Digital Key Phones + Telephone Sets) |
| 553 | [CC TV SYSTEM] |
| 554 | Supply of High Quality Image with 4 MP (2688x1520) 25/20 fps Ultra 265 WDRTechnology Enable Built In Microphone Smart IR Upto 30 Meters Dome Network Camera. |
| 555 | Supply of Network VIDEO Recorder (NVR) Upto 12 Megapixel 8 SATTA HDD Supported Upto 12TB For Each HDD 3 Incoming Bandwidth 320 Mbps Outgoing Bandwidth Same for 32 Channel. |
| 556 | Supply of 16 Power Over Ethernet Switch (POE) Switch Full Giga 100/1000 alongwith 2 Uplink. |
| 557 | Supply of Surveillance Hard Disc Drive 4 TB |
| 558 | Supply of 4U Metal Rack |
| 559 | CAT-6e Cable UL Cetrified / BIS Approved |
| 560 | Accessories For Cameras |
| 561 | Supply of 65\\" SMART LED TV 4K Series |
| 562 | PVC Conduict / Pipe 25mm |
| 563 | Cabling Charges In Running Meters |
| 564 | Installation, Testing & Commissioning of Cameras (Includin NVR Configuration. |
| 565 | Installation of PoE Switches & Racks Mounting. |
| 566 | [NETWORK SYSTEM] |
| 567 | Supply of 16 Power Over Ethernet Switch (POE) Switch Full Giga 100/1000 along with 2 Uplink. |
| 568 | Supply of WiFi 6 Long Range Access Point with Inbuilt PoE (3 Year Warranty) |
| 569 | Networking and Configuration |
| 570 | Supply of 4U Metal Rack |
| 571 | CAT-6e Cable UL Certified / BIS |
| 572 | PVC Conduict / Pipe 25mm |
| 573 | Cabling Charges In Running Meters |
| 574 | Supply of 24 Port Giga Byte Switches |
| 575 | IO BOX |
| 576 | Keystone |
| 577 | Networking and Configuration |
| 578 | Supply of 4U Metal Rack |
| 579 | CAT-6e Cable UL Certified / BIS |
| 580 | PVC Conduict / Pipe 25mm |
| 581 | Cabling Charges In Running Meters |
| 582 | Supply of 16 Port Giga Switches |
| 583 | AUDIO VIDEO |
| 584 | VIDEO |
| 585 | PTZ Camera Resolution: Full HD 1080p (1920×1080)Optical Zoom: 20× optical zoomDigital Zoom: 16× digital zoomInterfaces: USB 3.0, LAN, HDMI / DVIVideo Encoding: H.264 / H.265Control Protocols: VISCA, Pelco-D, Pelco-PUsage: Video conferencing, webinars, classroom recording, live streaming, meeting rooms |
| 586 | Optical zoom: 20× optical zoom for clear close-ups even from a distance.Resolution & Frame Rate: Supports Full HD — at high frame rate (Full HD@60 fps) for smooth, clear video output, which is useful for live streaming or conference video. Connectivity / Output: Has USB (likely USB 2.0 / 3.0) and HDMI outputs — so easy to connect to PCs, capture cards, monitors or codecs for video-conferencing or streaming. |
| 587 | Ceiling mount for Camera |
| 588 | Camera Switcher 4 X HDMI In, 1 X HDMI Out, 1 X USB Out, Picture in Picture, Picture by Picture |
| 589 | Confernce Digital Cable |
| 590 | Bezel less active LED AIO-C135 size 135’’ ,PP-1.56 mm Pixel Pitch, COB, Resolution Full HD 1920x1080, Aspect ratio 16:9,Brightness 600 nits, refresh rate 3840 Hz, w |
| 591 | Speaker type Broadband columnPeak power handling 480 W Program power handling 240 WContinuous power (AES) 120 W Impedance 12 ΩSensitivity (1W/1m) 92 dB Sound Pressure (Max. W/1m) 113 dBFrequency Range (-10 dB) 120 Hz - 20 kHLine Transformer Tappings 1 40 W - 125 Ω (70V) |
| 592 | Dual-channel Class-D amplifier 2 x 250WContinuous power (AES) @ 4 Ω Stereo 2 x 250 W@ 8 Ω Stereo 2 x 130 W@ 8 Ω Bridge 500 WFrequency Response (± 3 dB) 20 Hz - 20 kHzSpeakon compatible & terminal block output connections |
| 593 | Screen Size 65\\"Back Light Type DirectNative Resolution 3840 x 2160 (UHD)Brightness 400nit (Typ.)Viewing Angle(H x V) 178 x 178Response Time 8ms (G to G) |
| 594 | TV Ceiling Mount |
| 595 | Screen Size 55\\"Back Light Type DirectNative Resolution 3840 x 2160 (UHD)Brightness 400nit (Typ.)Viewing Angle(H x V) 178 x 178Response Time 8ms (G to G) |
| 596 | Confidence Monitor TV Trolly |
| 597 | AUDIO |
| 598 | Boundary Layer Retractable Chairman Unit Microphone |
| 599 | Boundary Layer Retractable Delegate Unit Microphone |
| 600 | Digital Controller for Integrated Processor with Look at me Built-in |
| 601 | Power Extenshion for Microphone |
| 602 | Echo Surpressor -Supressor is external whistling sound. |
| 603 | Combo- Wireless Handheld Microphone Variable Frequency. Polar pattern / directionality is cardioid — meaning it will pick up sound mainly from in front of the mic and reject some background noise |
| 604 | Ceiling SpeakerPower Handling, long-term continuous 20 WPower Handling, Peak 80 WNominal Impedance 16 Ω (transformer bypass)Transformer Taps, 100V 2.3, 4.5, 9 W, bypassTransformer Taps, 70V 1.2W, 2.3 W, 4.5 W, 9 W, bypass |
| 605 | Amplification Power: 2 × 160 W at 70/100VFrequency Response: 20 Hz – 20 kHz (+0/-3 dB)Dynamic Range: 88 dBBluetooth Version: 5.0Inputs: 2 balanced line, 2 unbalanced line, 1 mic/lineOutputs: 2 speaker, 1 aux line |
| 606 | Digital Signal Processor 8 X 8 ( Audio and Out,) USB Built in for VC, Built-in AEC |
| 607 | Pop-up Box design: It is a compact, pop-up box that can be installed into surfaces like conference tables to provide easy access to connectors without cluttering the workspace.Pop-up design: It is a compact, pop-up box that can be installed into surfaces like conference tables to provide easy access to connectors without cluttering the workspace. |
| 608 | high-performance video and audio modular matrix switcher supporting max 16 input signal sources and 16 output display synchronously. It supports different video signals with cross switching. Every video or audio signal is transmitted and switched independently to decrease signal attenuation. It supports various changeable cards including HMDI, VGA and HDBaseT etc. |
| 609 | 9 inputs multi format A/V presentation auto 4k Scaler Switcher that scales video signals to HDMI and HDBaseT outputs simultaneously. The HDBaseT output supports 48V PoH and can connect to a compatible HDBaseT Receiver up to a maximum of 100 meters (328ft). With 1 IR ALL IN and 1 IR ALL OUT, the IR control signals can be transmitted bi-directionally between the MP-SC-9T and compatible HDBaseT Receiver or HDBaseT Transmitter. It can be controlled either by front panel buttons, IR Remote, RS232 or GUI. |
| 610 | 4x4 USB 3.2 Matrix. It allows 4 x USB devices to be shared between 4 x host devices, supporting Plug-and-Play. The USB data transfer rate is up to 5Gbps. It provides advanced features including a web interface module for control and configuration of the Matrix, along with RS-232 for seamless control integration |
| 611 | HDMI 2.0 2x1 Presentation Switcher . It is designed to switch HDMI input or USB-C input to one HDMI output. It supports video resolution up to 4Kx2K@60Hz 4:4:4 8 bit , 1080P, and 3D In addition, there is smart built in EDID setting can be selected by the 4 pin DIP switch on the front panel. It supports stereo and multichannel audio on the HDMI inputs. In addition to the audio embedded in the HDMI output stream, the audio is simultaneously de-embedded to a balanced analog audio output. |
| 612 | 32–Port Master / Room ControllerINPUTS 1 built–in IR sensor (for learning)OUTPUTS 8 IR out and 8 relays on 2–pin terminal block connectors8 RS–232 serial on 3–pin terminal blocks, 8 GPI/O on 2–pin terminal blocks, 1 Ethernet on a RJ–45 connector, 1 micro–USB connector for sending P3K commands and performing a firmware upgrade |
| 613 | IR & TX Extender HDMI |
| 614 | Compact & Secure 4K Wireless Presentation DevicePorts 1 Ethernet: On an RJ–45 connector, 1 USB 3.0: On a female USB type–A connector, 1 USB 2.0: On a female USB type–A connectorOutputs 1 HDMI: On a female HDMI connectorVideo, Max Resolution: 4K@30Hz |
| 615 | 24× PoE+ 10/100 Mbps RJ45 ports, 2× Gigabit RJ45 Uplink ports, and 2× combo Gigabit SFP slot |
| 616 | Frequency Band Class Dual-Band Wireless Communication Standard 802.11nSecurity Protocol: 64/128/152-Bit Wep / Wpa / Wpa2-Enterprise,Wpa-Psk / Wpa2-Psk |
| 617 | Premium High Speed HDMI Cable with Ethernet, 1 m |
| 618 | Premium High Speed HDMI Cable with Ethernet, 3 m |
| 619 | Premium High Speed HDMI Cable with Ethernet, 5 m |
| 620 | 10\\" Touch Panel for control interface |
| 621 | DT i3/10th/8gb/128ssd/1tb win10pro |
| 622 | Rack 24U Material Stainless Steel Product Type Heavy Duty |
| 623 | Connector & Paich Cable |
| 624 | Twisted Shielded Cable 48Rs/Mtr as per requirment |
| 625 | Speaker Wire 2 X 1.5mm 130Rs./Mtr as per requirement |
| 626 | Microphone Wire 16AWG 100Rs./Mtr as per requirement |
| 627 | SUKRANTI- MR-C/ 6 Passenger Lift/ 408Kgs / 1.25 Speed / 3 Floors/ 3 Stops / Stainless Steel Car Cabin.All complete to the entire satisfaction of Engg in Charge/Architect. All Hardware INCLUSIVE as per design. |
| 628 | VRF AC Work |
| 629 | Variable Refrigerant Flow System |
| 630 | Supply & Installation of Outdoor Units |
| 631 | (Heat Pump Type) |
| 632 | Supply, Installation, Testing & commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating having all hermetically sealed single inverter type scroll 3 valve discharge type Compressor(s) at partial load condition, in fire protected chamber single compressors for above 14 HP modules,microprocessor based Controller, top discharge type condensing unit(s), with R410 A Refrigerant, vibration isolators with suitable foundation etc. complete as required. ODUs module should be based on auto By pass technology. The unit shall deliver the rated capacity at AHRI Conditions and Operating range should be above 52 degree ambient temperature and will be clearly mentioned in catalogue. The unit shall be suitable to work on 400V =/- 10%, 3 phase , 50 Hz AC power supply with inbuilt phase reversal protection and corrector technology.Low pressure shell type compressor will be accepted only. The unit shall be filled with firstcharge of the refrigerant and ready for use as required. |
| 633 | 50 HP |
| 634 | 54 HP |
| 635 | Connecting Kits |
| 636 | Supply & Installation of Indoor Units |
| 637 | Supply, installation, testing and commissioning of followingminimum capacity VRV/VRF Highwall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multi speed motor , coil section with DX copper coil electronic expansion valve, outer cabinet with smart coating of nano partical with supper hydophobic surface , cordless remote control, drain pan, necessary accessories etc., suitable for operation on 230V±10%,50Hz single phase AC supply with fire resistant metal box protection for indoor units PCB, complete as required. IDUs should be based on auto By pass technology. The unit shall have automatic force shutdown provision in case of fire on receiving signa from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27Degree C DB and 19 Degree C WB temperature. |
| 638 | VRF 4-WAY CASSETTE TYPE Type Units: 4.13 Tons |
| 639 | VRF 4-WAY CASSETTE TYPE Type Units: 3.33 Tons |
| 640 | VRF 4-WAY CASSETTE TYPE Type Units: 2.65 Tons |
| 641 | VRF 4-WAY CASSETTE TYPE Type Units: 1.65 Tons |
| 642 | VRF 4-WAY CASSETTE TYPE Type Units: 1.08 Tons |
| 643 | Supply & Installation of Individual Controllers |
| 644 | Corded Remote Controls |
| 645 | Supply & Installation of Imported Refrigerant Joints |
| 646 | Provision of fittings such as T- Type Refrigerant joints as required as per layout drawings & standard. |
| 647 | Supply & Topping of Additional Gas Charging |
| 648 | Pressure testing & charging of refrigerant R410 gas of above mentioned AC system complete as required at site. |
| 649 | Supply & Installation of Refrigerant Piping & Support |
| 650 | Supply, Installation, Testing & commissioning of Interconnecting copper refrigerant piping closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as perspecifications including MS slotted angle SWG support for refrigerant piping. Complete as per site requirement. |
| 651 | 41.3 mm O.D. (insulation : 19 mm) |
| 652 | 34.4 mm O.D. (insulation : 19 mm) |
| 653 | 28.6 mm O.D. (insulation : 19 mm) |
| 654 | 22.2 mm O.D. (insulation : 19 mm) |
| 655 | 19.1 mm O.D. (insulation : 13 mm) |
| 656 | 15.9 mm O.D. (insulation : 13 mm) |
| 657 | 12.7 mm O.D. (insulation : 13 mm) |
| 658 | 09.5 mm O.D. (insulation : 13 mm) |
| 659 | 06.4 mm O.D. (insulation : 13 mm) |
| 660 | Supply & installation of Cable Tray |
| 661 | Supply and laying of MS cable tray support for refrigerant piping & transmission wiring on roof top. |
| 662 | 300mm X 50 mm X 1.6 mm |
| 663 | Supply & installation of Drain Piping |
| 664 | Supply, Installation, Testing & commissioning of UPVC drain piping for indoor units complete with necessary elbow, tees, reducers etc. duly insulated with 6 mm thick closed cell elastomeric nitrile rubbertubing/sheet rapping as per following size:Complete as per site requirement |
| 665 | 32 mm dia. |
| 666 | 40 mm dia. |
| 667 | 50 mm dia. |
| 668 | Supply & installation of Transmission Wiring & Controller Wiring |
| 669 | Supply, Installation, Testing & commissioning of control cum transmission wiring of 2 core x 1.5 sqmm sheilded copper wire suitable between indoor and oudoor and indoor units, complete as required. |
| 670 | Civil Work |
| 671 | Chiselling and Hole Cutting Work |
| 672 | Scaffolding work for vertical copper pipe Work |
| 673 | Providing of Wall Clock which is made by metal & fiber with functional metallic machine etc |
| 674 | Providing of Decorative wall art and paintings which includes canvas , HD paper media , metal and fiber etc. |
| 675 | Providing of Metallic Logo made by 12mm or 18mm ply with finish by 4mm veneer with PU polish and CNC work with backlit |
| 676 | Providing of 3’ x 7’ Name Board made up with 12 mm white corrian and letters made by 3 mm brown acrylic with CNC work . |
| 677 | Providing of Artificial plants with planter made by synthetic materials such as polythene or polypropylene, which includes bamboo plants, palm, fiddle etc. |
| 678 | Providing of 2’-6” x 6’ Signage Board coverning with 1 mm acrylic sheet with translite UV printing with 195 micron and mounting with aluminium clips. |
| 679 | Providing of wooden ceiling with 18 mm or 12 mm ply with ISI marked and finished with 4 mm Veneer with PU polish and CNC Work |
| 680 | Providing of backdrop with 18 mm or 12 mm ply with ISI marked and finished with 4 mm Veneer, Designer laminates. Designer leatherite. |
| 681 | FURNITURE |
| 682 | TRANSPORT COMMISSIONER OFFICE |
| 683 | Table made by 12 mm and 18mm ply board with 4 mm Veneer and finished by PU Polish or PU coating with designer Top. All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE L3300xW900xH750) |
| 684 | Credenza made by 12 mm and 18mm ply board with 4 mm Veneer and finished by PU Polish or PU coating with designer Top. All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE L1650xW450xH600) |
| 685 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 686 | Medium Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 687 | 3 Seater Sofa made by pine wood and finished with designer fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 688 | Single Seater Sofa made by pine wood and finished with fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 689 | Center Table made by 12 mm and 18 mm ply with ISI marked and finished with designer laminate(SIZE L1500xW900xH400) |
| 690 | Low Height Storage made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . Storage inculdes Shelfs and drawers. All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L6300xW450xH750) |
| 691 | TOILET |
| 692 | Toilet Vanity made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1150X W530X H600) |
| 693 | PANTRY |
| 694 | Undercounter & overhead cabinet made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. |
| 695 | WAITING AREA |
| 696 | 3 Seater Sofa made by pine wood and finished with designer fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 697 | Single Seater Sofa made by pine wood and finished with fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 698 | Center Table made by 12 mm and 18 mm ply with ISI marked and finished with designer laminate. (SIZE L1500xW600xH400) |
| 699 | Console made by 12 mm and 18 mm ply with ISI marked and finished with designer laminate. |
| 700 | Designer chair made by pine wood and finished with fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 701 | Center Table made by 12 mm and 18 mm ply with ISI marked and finished with designer laminate. (SIZE D600xH400) |
| 702 | TRANSPORT COMMISSIONER CAMP OFFICE |
| 703 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L2100xW750xH750) |
| 704 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1500xW450xH600) |
| 705 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 706 | Medium Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 707 | Full Height Storage made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . Storage inculdes Shelfs and drawers. All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L7800xW450xH3100) |
| 708 | Low Height Storage made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . Storage inculdes Shelfs and drawers. All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L2100xW450xH2400) |
| 709 | RECEPTION |
| 710 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L2900xW830xH750) |
| 711 | Medium Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 712 | 3 Seater Sofa made by pine wood and finished with designer fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 713 | Center Table made by 12 mm and 18 mm ply with ISI marked and finished with designer laminate.(SIZE L1050xW750xH400) |
| 714 | Side Table made by 12 mm and 18 mm ply with ISI marked and finished with designer laminate.(SIZE L450xW450xH450) |
| 715 | PASSAGE WAITING |
| 716 | Center Table made by 12 mm and 18 mm ply with ISI marked and finished with designer laminate.(SIZE L1050xW750xH400) |
| 717 | CONFERENCE HALL |
| 718 | Conference Main Table made by 12 mm and 18mm ply board and finished with designer 1 mm laminate and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE-L13800xW4075xH750) |
| 719 | Conference Table made by 12 mm and 18mm ply board and finished with designer 1 mm laminate and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE-L12675xW600xH750) |
| 720 | Medium Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 721 | TOILET |
| 722 | Toilet Vanity made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L800xW500xH600) |
| 723 | OFFICER CABIN-1 |
| 724 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE 2100xW750xH750) |
| 725 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1500xW450xH600) |
| 726 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 727 | Medium Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 728 | 2 Seater Sofa made by pine wood and finished with designer fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 729 | PS CABIN-1 |
| 730 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE L1900xW675xH750) |
| 731 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1200xW450xH600) |
| 732 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 733 | Full Height Storage made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . Storage inculdes Shelfs and drawers. All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L3300xW450xH3150) |
| 734 | OFFICER CABIN-2 |
| 735 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE 2100xW750xH750) |
| 736 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1500xW450xH600) |
| 737 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 738 | Medium Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 739 | 2 Seater Sofa made by pine wood and finished with designer fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 740 | PS CABIN-2 |
| 741 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE L1900xW675xH750) |
| 742 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1200xW450xH600) |
| 743 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 744 | Full Height Storage made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . Storage inculdes Shelfs and drawers. All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L3300xW450xH3150) |
| 745 | OFFICER CABIN-3 |
| 746 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE 2100xW750xH750) |
| 747 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1500xW450xH600) |
| 748 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 749 | Medium Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 750 | 2 Seater Sofa made by pine wood and finished with designer fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 751 | PS CABIN-3 |
| 752 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE L1900xW675xH750) |
| 753 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1200xW450xH600) |
| 754 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 755 | Full Height Storage made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . Storage inculdes Shelfs and drawers. All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L3300xW450xH3150) |
| 756 | OFFICER CABIN-4 |
| 757 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE 2100xW750xH750) |
| 758 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1500xW450xH600) |
| 759 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 760 | Medium Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 761 | 2 Seater Sofa made by pine wood and finished with designer fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 762 | PS CABIN-4 |
| 763 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE L1900xW675xH750) |
| 764 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1200xW450xH600) |
| 765 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 766 | Full Height Storage made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . Storage inculdes Shelfs and drawers. All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L3300xW450xH3150) |
| 767 | OFFICER CABIN-5 |
| 768 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE 2100xW750xH750) |
| 769 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1500xW450xH600) |
| 770 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 771 | Medium Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 772 | 2 Seater Sofa made by pine wood and finished with designer fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 773 | PS CABIN-5 |
| 774 | Table made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge.(SIZE L1900xW675xH750) |
| 775 | Credenza made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1200xW450xH600) |
| 776 | High Back Chair, Chrome Plated Pipe Frame And Arm, Leatherette On Arm, Net Leatherette Tapestry, Gas Lift, Chrome Base |
| 777 | Full Height Storage made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . Storage inculdes Shelfs and drawers. All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L3300xW450xH3150) |
| 778 | REST ROOM -1-5 |
| 779 | Single Bed made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L1800xW1150xH450) |
| 780 | WAITING AREA |
| 781 | 3 Seater Sofa made by pine wood and finished with designer fabric or leathrite with legs teak wood or ms with pu polish or pu coating. |
| 782 | Center Table made by 12 mm and 18 mm ply with ISI marked and finished with designer laminate.(SIZE L1050xW750xH400) |
| 783 | SHE'S & HE'S TOILET |
| 784 | Toilet Vanity made with 12 mm and 18mm ply board and finished with designer 1 mm laminate with designer handles and other hardwares or accessories as per requirement . All complete as per directions & instructions of Architect/Eng-In-Charge. (SIZE L900xW530xH600) |
| 785 | GST Extra as applicable Please Enable Macros to View BoQ information |