|
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 2 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres. All kinds of soil : |
| 3 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil : |
| 4 | Supply and filling of dry stone soling in foundation trenches/under floors tightly hand packed with hand ramming, dressing ,watering incld. carriage of material from source to site of work complete |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m |
| 6 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil. |
| 7 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as10 sqm on plan including disposal of excavated earth, leadupto50meterand lift upto 1.5m, as directed by Engineer-in-Charge. All kinds of soil |
| 8 | Removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive |
| 9 | Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete. |
| 10 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering. All work up to plinth level 1:4:8 (1 Cement: 4 coarse sand: 8 grade stone aggregate 40mm nominal size) |
| 11 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering. All work up to plinth level 1:2:4 (1Cement: 2 coarse sand: 4 grade stone aggregate 20mm nominal size) |
| 12 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominalsize) |
| 13 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering all work upto plinth level in 1:3:6 (1 cement : 3 coarse sand : 6 stone aggregate 20mm nominal size) including curing complete. |
| 14 | Providing and laying cement concrete in retaining walls,return walls,walls(any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,butteressses,string or laces,courses,parapets,coping,bed blocks,anchor blocks,plain window sills,sunken floors fillets etc.upto floor five level,excluding the cost of centring,shuttering and finishing in 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20 mm nominal size crushed |
| 15 | Providing and laying cement concrete in retaining walls,return walls,walls(any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,butteressses,string or laces,courses,parapets,coping,bed blocks,anchor blocks,plain window sills,sunken floors fillets etc.upto floor five level,excluding the cost of centring,shuttering and finishing in 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) |
| 16 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with. 1 : 1.5 : 3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) |
| 17 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with. 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) including all carriages. |
| 18 | Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete |
| 19 | Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete |
| 20 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete |
| 21 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 22 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 23 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 24 | Centering and shuttering including strutting propping etc. and removal of form for foundation, footings basses of columns etc . For mass concrete |
| 25 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams,plinth beams, girders, bressumers and cantilevers |
| 26 | Centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platforms. |
| 27 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 28 | Centering and shuttering including strutting, propping etc. and removal of form for stairs (excluding landings) except spiral staircases. |
| 29 | Centering and shuttering including strutting, propping etc. and removal of form for columns,pillars,piers,abburtments,posts and struts |
| 30 | Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls |
| 31 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all levels, Thermo-Mechanically Treated bars of grade Fe-500D or more, including all carriages. |
| 32 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. All works upto plinth level |
| 33 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. All works above plinth level upto floor V level |
| 34 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) with Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 35 | Random rubble masonry with hard stone from quarry in foundation and plinth in cement mortar 1:6 (1cement : 6 course sand), including leveling up with cement concrete 1:6:12 (1cement: 6 course sand: 12 graded stone aggregate 20mm nominal size) at plinth level with all leads lifts cost & carriages of materials involved upto site of work complete |
| 36 | Dry Random Rubble masonry in foundation and plinth using quarry stones with bond stones all leads lifts cost & carriages of materials involved upto site of work complete. |
| 37 | Random Rubble masonry with hard stone in foundation and plinth using Quarry Stone including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) and curing complete with Cement mortar 1:6 (1 Cement : 6 coarse sand) (labour only) |
| 38 | Dry random rubble masonry with hard stone in foundation and plinth using quarry stone with bond stone (labour only) |
| 39 | Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing. One face dressed Rough chisel dressed |
| 40 | Providing and laying rough chisel dressed Devri Stone in kerbs, of size 200x200 mm face with chamfer in cement mortar 1: 6 (1 cement : 6 coarse sand) including curing. |
| 41 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab over 0.5 sqm) |
| 42 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge, |
| 43 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work |
| 44 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 45 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalization or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanized with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bimetallic contacts all complete required to perform as per specification and drawing The item includes cost of all material &labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. |
| 46 | Providing wood work in frames of doors, windows, clesrestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners of Imported KD Wood complete job |
| 47 | Providing and fixing of 40X5mm flat iron hold fast 40 cm long including fixing to frame with 10mm dia bolts, nuts and wooden plugs and embeddings in cement concrete block 30X10X15 cm 1:3:6 mix ( 1 Cement : 3 Coarse sand :6 graded stone aggregate 20 mm nominal size) |
| 48 | Providing wood work in frames of false ceiling , Partitions etc. Sawn and fixed in poisition in budloo wood |
| 49 | Providing hoisting and fixing trusses/purlins/ rafters/posts/post- plates, false ceiling , Partitions etc. Sawn and fixed in poisition or like components including cost of screws etc. complete First class Poplar wood. |
| 50 | Providing and fixing 35 mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. First class KD wood |
| 51 | Providing and fixing 35 mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge First class KD wood. |
| 52 | Providing and fixing of 4 mm thick float glass panes to door, window, and ventillator frames(fixed portion) embeded in putty and fixed with painted beadings including cost of nails etc |
| 53 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors,windows and clerestory windows(Area of opening for panelled inserts excluding portion inside grroves or rebates to be measured) .Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Pre-laminated particle board with decorative lamination on both sides.Grade I,Type II IS:12823 marked. |
| 54 | Providing and fixing 35 mm thick ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. |
| 55 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, |
| 56 | Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 57 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles,including applying a priming coat of approved steel primer, |
| 58 | Providing and fixing 1mm thick M.S. sheet sliding-shutters with frame and diagonals braces of 40x40x6mm angle iron, 3mm M.S. gusset plates at the junction and corners, 25mm dia pulley, 40x40x6mm angle and T-iron guide at the top and bottom respectively including applying a priming coat of approved steel primer, |
| 59 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angles 40x40x6mm for diagonal braces. |
| 60 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters,80x0.90 mm M.S. laths with 0.90 mm thick top cover, including providing and fixing ball bearing. |
| 61 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc.,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two or more coats of synrhetic enemal paint , including welding and bolted with special shaped washers etc.complete Hot finished welded type tubes. |
| 62 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two or more coats of synrhetic enemal paint using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, grills,brackets, gates and similar works, |
| 63 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube. |
| 64 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. G.I.pipes |
| 65 | Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S Flat 15x3 mm and nuts and bolts complete. Galvanized M.S wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides. |
| 66 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 67 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 25mm thick with 12.5 mm nominal size stone aggregate. |
| 68 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20 mm nominal size stone aggregate. |
| 69 | Providing and fixing strips in joints of terrazzo/ cement concrete floors. Glass strips 40 mm wide and 4 mm thick. |
| 70 | Providing and fixing strips in joints of terrazzo/ cement concrete floors. Glass strips 40 mm wide and 6 mm thick. |
| 71 | Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Light shade using white cement |
| 72 | Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand), Ordinary cement without any pigment, |
| 73 | Flooring with marble stone of 18 mm thick as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including rubbing, polishing and curing complete with:Makrana White Second quality. |
| 74 | Flooring with marble stone of 18 mm thick as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including rubbing, polishing and curing complete with:Black zebra. |
| 75 | Flooring with marble stone of 18 mm thick as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including rubbing, polishing and curing complete with:Udaipur green marble. |
| 76 | Providing & fixing coloured rubber moulded Interlock Floor Paver Tiles 50 mm thick of M20 grade and of approved quality and make jointed with neat cement slurry mixed with pigment to match the shade of tiles incld. rubbing, cleaning and curing complete on 20 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand), Light shade using white cement. |
| 77 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown. |
| 78 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. In all colours, shades, except White, Ivory, Fume Red Brown. |
| 79 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. including all carriages. |
| 80 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete, Size of tile 600x600 mm |
| 81 | Size of tile 800x800 mm |
| 82 | Size of tile 1000x1000 mm |
| 83 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building or at required places all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 84 | Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required: 0.63 mm thick with zinc coating not less than 275 gram/m2, |
| 85 | Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required: 0.50 mm thick with zinc coating not less than 275 gram/m2, |
| 86 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gram/m2. |
| 87 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.50 mm thick with zinc coating not less than 275 gram/m2. . |
| 88 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 1.00 mm thick with zinc coating not less than 275 gram/m2, |
| 89 | Providing & fixing colour coated (Hi-Rib) G.I sheet roofing 0.50mm thick incl. vertical/curved surface fixed with polymer coated J or L hooks bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I limpet washer and over lapping of sheets complete in horizontal vertical trusses incl. cutting to size and shape wherever required including Ridges or Hips of 60 cm overall width colour coated sheets 0.50mm thick and valleys of 90 cm width colour coated sheets 0.50mm thick etc complete as per the directions of Incharge Engineer. |
| 90 | Providing and fixing of plain eaves boarding 300mm x 40 mm (nominal size) 2nd class kail wood incl cost of nails. |
| 91 | Providing and fixing 20mm thick wooden planks ceiling (frame work for base to be paid for separately) with M.S. screws Budloo/fir wood |
| 92 | Providing and fixing of KHATAM BANDI ceiling of first class budloo/fir wood incld.12 mm thick ply under layer and 1 m x 1 m mesh frame work of 50 mm x 50 mm budloo wood battens incld fixing the meshed frame properly with sufficent no of gutties and sprit polishing two or more coats, Chaar Gul. |
| 93 | 12mm Cement plaster of mix in 1 : 4 ( 1 cement : 4 coarse sand) |
| 94 | 12mm Cement plaster of mix in 1 : 6 ( 1 cement : 6 coarse sand) |
| 95 | 15 mm Cement plaster on the rough side of single or half brick wall of mix: 1:6 (1 cement:6 coarse sand) |
| 96 | 15 mm Cement plaster on the rough side of single or half brick wall of mix: 1:4 (1 cement:4 coarse sand), |
| 97 | 6mm cement plaster to ceiling of mix 1 : 3 (1 cement: 3coarse sand) |
| 98 | Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surfaceeven and smooth complete |
| 99 | Pointing on stone work with cement mortar 1 : 3 (1 cement : 3 fine sand) :Flush/Ruled Pointing, |
| 100 | Distempering with dry distemper of approved brand andmanufacture (two or more coats) and of required shade on new work, over and including water thinnable priming coat to give an even shade |
| 101 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and inluding priming coat with water thinnable cement primer. |
| 102 | Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm), |
| 103 | Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm |
| 104 | Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm), |
| 105 | Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/10sqm over and including priming coat of water exterior paint applied @ 2.20kg/10sqm), |
| 106 | Applying priming coat With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 107 | Applying priming coat With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works . |
| 108 | Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 109 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work |
| 110 | Varnishing with varnish of approved brand and manufacture:Two or more coats of glue sizing with copal varnish over and under coat of flatting varnish. |
| 111 | Providing and applying white cement based putty 2 mm thick of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 112 | Distempering with 1st quality acrylic distemper (ready mixed)having VOC content less than 50 gms/litre,two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer’s specifications , |
| 113 | Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface |
| 114 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 115 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 116 | Painting on steel work with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade on old work (two or more coats) . |
| 117 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work |
| 118 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work. |
| 119 | Distempering with 1st quality Acrylic/oil bound washable distemper (ready-made) having VOC content less than 50 grams/litre of approved manufacturer and of required shade and colour complete as per manufacturers’ specifications, one or more coats on old work |
| 120 | Finishing walls with water proofing cement paint of required shade:Old work (one or more coats applied @ 2.20 kg/10sqm) complete |
| 121 | Finishing walls with textured exterior paint of required shade:Old work (one or more coats) applied @1.82 ltr/10sqm |
| 122 | Varnishing with varnish of approved brand and manufacture: One or more coats with copal varnish |
| 123 | Melamine polishing on wood work (one or more coats) |
| 124 | Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead, With cement mortar 1:4 (1 cement : 4 coarse sand), |
| 125 | Providing and fixing brass curtain rods of wall thickness 1.25 mmwith two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete.25 mm diameter. |
| 126 | Providing & fixing White vitreous china water closet squatting pan(Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. Long pattern W.C Pan of size 580x440 mm including all carriages. |
| 127 | Providing & fixing White vitreous china water closet squatting pan(Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.Orissa pattern W.C Pan of size 580x440 mm including all carriages. |
| 128 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. including all carriages. |
| 129 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix), |
| 130 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1 :4:8 or richer mix (i/c equivalent design mix), |
| 131 | Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge. |
| 132 | Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: in cement mortar |
| 133 | Demolishing stone rubble masonry manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar |
| 134 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead |
| 135 | Dismantling steel work in single sections including dismembering and stacking within 50 meters lead in :Channels, angles, tees and flats |
| 136 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 meters lead |
| 137 | Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead. |
| 138 | Dismentalling of damaged CGI sheets fencing including stcking of serviceable materials dismantelled materials to be handed over to college authorities complete |
| 139 | Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of : G.S. Sheet |
| 140 | Dismantling aluminum / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material within 50 meters lead as directed by Engineer-in-charge |
| 141 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. |
| 142 | Supplying and filling of good earth including digging earth carrying by lorry, placing, watering, dressing and ramming in layers not over 200mm thick and consolidation with PRR of 8-10 ton capacity including carriage of earth from approved source of supply to site of work complete including Royalty and all carriages. |
| 143 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid |
| 144 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 145 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. including Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings, |
| 146 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 147 | Providing and fixing kitchen sink including making all connections excluding cost of fittings : White glazed fire clay sink of size 600x450x250 mm including all carriages |
| 148 | Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittingsand fixtures complete: 10 liter capacity -White |
| 149 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia |
| 150 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete:Flexible pipe 32 mm dia |
| 151 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm |
| 152 | Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete |
| 153 | Providing and fixing toilet paper holder C.P. brass |
| 154 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.External work including trenching, refilling ,carriages etc..PN-16 pipe , 40mm OD(SDR-7.4) |
| 155 | PN-16 pipe , 32mm OD(SDR-7.4) |
| 156 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall,carriages etc.PN-16 pipe , 25mm OD(SDR-7.4) |
| 157 | PN-16 pipe , 32mm OD(SDR-7.4) |
| 158 | PN-16 pipe , 20 mm OD(SDR-7.4) |
| 159 | Providing and fixing PPR Unions PPR Union 20mm |
| 160 | PPR Union 25mm |
| 161 | PPR Union 32mm |
| 162 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall: 15 mm dia. nominal bore |
| 163 | 20 mm dia. nominal bore |
| 164 | Providing and fixing G.I. pipes complete with G.I. fittings(Medium grade) excluding trenching and refilling etc. (external work) 15 mm dia. nominal bore |
| 165 | 20 mm dia. nominal bore |
| 166 | 25 mm dia. nominal bore |
| 167 | Providing and fixing brass bib cock/stop cock of approved quality. 15 mm nominal bore |
| 168 | 20 mm nominal bore |
| 169 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm nominal bore |
| 170 | 20 mm nominal bore |
| 171 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 15 mm nominal bore |
| 172 | 20 mm nominal bore |
| 173 | 25 mm dia. nominal bore |
| 174 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete 15 mm nominal bore |
| 175 | 20 mm nominal bore |
| 176 | 24 mm nominal bore |
| 177 | Providing and placing on terrrace (at all floor levels) polyethene water storage tank ISI:12701 marked triple layer indicating the BIS License No with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fittings and base support for tank (Sintex, Electroplat, Star, Lotus or equivalent having valid ISI license) |
| 178 | Construction brick massionary manhole with 7.5 class designation bricks in cement mortar 1:4 (1 cement; 4 fine sand ) CI cover with frame , foundation concrete 1:3:6 (1cement : 3 fine sand :6 graded stone aggregrate 20 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand ) finished smooth with a floating coat of neat cement on walls and bed concrete etc complete as per standard design: as per the directions of site engineer Inside dimensions 300x300 x450 mm deep |
| 179 | Inside dimensions 600x600 x750 mm deep |
| 180 | Inside dimensions 450x450 x600 mm deep |
| 181 | Inside dimensions 900x900 x1050 mm deep |
| 182 | Providing and fixing of CP brass fittings of approved quality and manufacture (Hindware, Cera, Jaguar or Equivalent Quality) with all fittings and fixtures complete Bibcock |
| 183 | Angle Valve |
| 184 | Soap case |
| 185 | Grating |
| 186 | wall mixer/Basin mixer |
| 187 | Pillar cock |
| 188 | Towel rod |
| 189 | Towel ring |
| 190 | Health faucet with cp flush pipe,nozzel and hook. |
| 191 | CP Extension Niples 20mm, 25mm, 40mm long |
| 192 | Toilet paper holder with toilet paper |
| 193 | Sink mixer |
| 194 | Supply of PVC / Foam insulation for external G.I pipes of different dia meter 15mm dia |
| 195 | 20 mm dia |
| 196 | 25 mm dia |
| 197 | Supply of polythene sheet for insulation (2'-6'' wide) |
| 198 | Supply of PVC connection of required size of approved /Superior Quality |
| 199 | Providing and Fixing of PVC pipes with fittings like P-bend,D-bend,P/F-Trap, collar, junction, Door Tee,Reducer etc (B-Type) of approved brand and manufacture (Prince/ Supreme or Equivalent brand) 100 mm dia |
| 200 | Providing and Fixing of PVC pipes with fittings like P-bend,D-bend,P/F-Trap, collar, junction, Door Tee,Reducer etc (B-Type) of approved brand and manufacture (Prince/ Supreme or Equivalent brand) 75 mm dia |
| 201 | Providing and Fixing of PVC pipes with fittings like P-bend,D-bend,P/F-Trap, collar, junction, Door Tee,Reducer etc (B-Type) of approved brand and manufacture (Prince/ Supreme or Equivalent brand) 50 mm dia |
| 202 | Providing and fixing of water heating geysers of approved brand & quality (Venus/ Jaguar/ Racold or eqviuallent) with all necessary fittings and fixtures complete Job. 50 Ltr capacity complete |
| 203 | Providing and fixing of water heating geysers of approved brand & quality (Venus/ Jaguar/ Racold or eqviuallent) with all necessary fittings and fixtures complete Job. 25 Ltr capacity complete |
| 204 | Providing and fixing of 6 mm thick plywood(kit ply,Greenply,Century,Sarda,Mayur or equivalent) in ceiling/ partition of walls or equivalent work fixed over 2''x2'' frame work of imported wood with cost of Nails, cornice, etc all inclusive |
| 205 | Providing and fixing of 12 mm thick plywood/board(kitply,Greenply,Century,Sarda,Mayur or equivalent) in ceiling/partition of walls or equivalent work fixed over 2''x2'' frame work of imported wood with cost of Nails, cornice, etc all inclusive including cost and carriage of all material involved complete. |
| 206 | Providing & fixing of 12 mm thick imported wooden panelling over 12mm thick plyboard (kit ply, Greenply, Century,Sarda,Mayur or equivalent) including cost of ply board, cornice 75 mm wide,beading polishing two or more coats of malamine / MDF polish , cornice, nails etc and carriages all inclusive complete job. as per the directions of incharge engineer at site |
| 207 | Providing & fixing of laminated wooden flooring 12mm thick AC/ 4-5 Non Scratching type of approved quality laid over 06mm thick thermocol with 50mm wide skirting/ door profile of approved quality Green Panel/ Action Tesa including cost & cariages of materials involved complete job. |
| 208 | Providing & fixing of 6mm thick PVC board panelling of approved quality (Green panel/ Action Tesa) with all necessary fittings including 12mm plyboard base under panelling fixed over 2''x2'' frame work of imported wood with cost of Nails, cornice etc of approved quality all inclusive with cost of labour, materials and carriages of all involved materials complete. |
| 209 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge incld.glazing of float glass panes 5mm thick for windows,ventilators etc and Aluminium sheets(ACP)as per size required for panelling of doors/partitions and dash fasteners,Powder coated aluminum (minimum thickness of powder coated 50 microns) all complete frame work,shutters ,float glass,ACP etc complete job. |
| 210 | Providing/ Fixing of acrylic board 5mm thick including letter writing with logo of approved shape , size & design duly approved by engineer incharge. including plywood sheet base of (3'x2'-0'') and acrylic board of (3'x2') with all accessories like ribbon, sessor, curtain, decoration as per requirement. All inclusive with cost of labour, material & carriages of all involved materials upto site of work complete job (Work to be carried out as per directions of Engineer incharge) for inaugration purpose |
| 211 | Providing/ Fixing of granite stone board 18mm thick including letter writing with logo of approved shape , size & design of size (3'x2') duly approved by engineer incharge with all accessories like ribbon, sessor, curtain, decoration as per requirement. All inclusive with cost of labour, material & carriages of all involved materials upto site of work complete job (Work to be carried out as per directions of Engineer incharge) for inaugration purpose |
| 212 | Supply & fixing of Curtains of approved cloth, size (7'x4'), colour, quality make including all carriages involved.(sample to be got approved from competent authority) |
| 213 | Supply & fixing of Curtains with full crewel work of approved cloth, size (7'x4'), colour, quality make including all carriages involved.(sample to be got approved from competent authority) |
| 214 | Providing and fixing nickle plated M.S. pipe curtain rods with nickle plated brackets and ornamental type M.S Nickle plated steel holders 20 mm dia pipe (Heavy type) incl. cost & carriage of materials involved complete job |
| 215 | Supply of Uniform for cooks , chefs & helpers (Unifrom shall include upper/ Shirt/ Apran Lower/ Trouser / Pent, White Tennis fleet, socks, cap, gloves) |
| 216 | Providing & laying of furnishing of approved quality 1st grade carpet (Kohinoor, Crown) including P/L of Thermocol of superior quality (10mm thickness) with cost/ labour/ carriage and other charges complete job (Sample to be got approved from competent authority before laying of furnishing) |
| 217 | Providing & laying of furnishing of approved quality 1st grade carpet (Khalifa) including P/L of Thermocol of superior quality (10mm thickness) with cost/ labour/ carriage and other charges complete job (Sample to be got approved from competent authority before laying of furnishing) |
| 218 | Providing & fixing of furnishing of approved quality (Iranian wall to wall) including sewing, Stiching sides and fixing with SR solution including cost of 12mm Thermocol complete job. Including all carriages upto site of work (Sample to be approved by competent authority) |
| 219 | Providing and fixing of Excel matting fixed with SR solutions/ adhesive of superior quality including cost of SR as per directions of Engineer incharge at site (sample to be got approved by competent authority) Grade 1st |
| 220 | Providing and fixing of Excel matting fixed with SR solutions/ adhesive of superior quality including cost of SR as per directions of Engineer incharge at site (sample to be got approved by competent authority) Grade 2nd |
| 221 | Providing and fixing of Excel matting fixed with SR solutions/ adhesive of superior quality including cost of SR as per directions of Engineer incharge at site (sample to be got approved by competent authority) Grade 3rd |
| 222 | Supply of leather covered 5 seater Sofa set of approved colour, design, size and make with central and side tables including all carriages upto site of work ( sample to be got approved from competent authority) complete job |
| 223 | Renovation / Repair of 5 seat Sofa set (3 seater 1 No, single seater 02 No) including providing springs ,cloth covers/ cushions etc with all carriages upto site of work complete job |
| 224 | Repairs to existing chairs by way of providing necessary screws, nails, foam and leather etc complete |
| 225 | Hire charges for Supply of tables of required size (For 2 days) including all carriages to & fro |
| 226 | Providing & Fixing of 1.0 HP water Motor with all fittings like inlet and outlet connections , electric controlled setup with service line including making of Plateform as per requirement covered with CGI Sheet fixed over angle iron frame work with all fittings as per the directions of Engineer In-Charge Complete job including carriages upto site of work ( Kirlosker, Usha, Cromptom Greaves, Havelles or equivalent) |
| 227 | Repairing of AC's of all capacities 1.00 Ton, 1.5 Ton, 2.00 Ton including replacing of damaged spare parts as per the directions of site engineer |
| 228 | Providing and fixing of water heating geysers of approved brand & quality ( Classic, Sharp,Usha)or eqviuallent) with all necessary fittings and fixtures complete Job. 50 Ltr capacity including all costs and cariages complete |
| 229 | Providing and fixing of water heating geysers of approved brand & quality ( Classic, Sharp,Usha)or eqviuallent) with all necessary fittings and fixtures complete Job. 25 Ltr capacity including all costs and cariages complete |
| 230 | Supply and fixing of geyser elements with thermostate including all necessary fittings and fixtures complete |
| 231 | Supply and filling of Gas for AC's of all capacities including all charges. |
| 232 | Supply of indoor PCB/ controlling unit for AC (Daikhan, Hitachi or equivalent) 5 star rating |
| 233 | Supply of insulated copper pipes for AC's of approved quality. |
| 234 | Construcition of Notice Board fabricate with wooden frame work with lockable arrangements of required size and shape with rabbit mesh including handles & hinges etc complete job as per requirement (sample to be got approved from competent authority) |
| 235 | Supply & installation of roll of hohour board with walnut hand carving cornice over prelimenated board 12mm thick including writing of letters as per the requirement & directions (sample to be got approved from competent authority) |
| 236 | Providing & fixing of Wall paper of superior quality having plastic coating and of approved design & shade to be fixed on walls with adhesive / chemical based material. All inclusive with cost of wall paper, chemical / adhesive & labour complete. (Sample to be got approved from competent authority) |
| 237 | Supplying Instalation & Commisioning of Luminious AMAZE 3875 / 36 Volt 3500 VA sinewave Inverter or equivalent make for Home, Offices and Shops incl 200 AH Battries (03) No's incl all leads lifts cost & Carriages complete Job |
| 238 | Providing & fixing of 12mm thick imported wooden Tiles over plywood base including cost of Nails, Cornice etc of approved quality, applying malamine / MDF polish of approved quality. All inclusive with cost of material, labour and carriage of all involved materials upto site of work complete. Work to be executed as per the directions of Engineer incharge at site of work.(Excluding cost of plyboard) |
| 239 | Providing & Supplying of Gas Room Heater of approved quality with electric pulse ignition lighter gas heater with kit - LPG Gas Room Heater incl all carriages with all leads and lifts as per directions of site incharge complete job |
| 240 | Providing and fixing of Warmex 1000/2000 Watts Electric PTC Wall Mount Heater Superb WM incl all carriages with all leads and lifts as per directions of site incharge complete job |
| 241 | Providing and Supplying of Heating Pillars of Standard Quaility incl all carriages with all leads and lifts as per directions of site incharge complete job |
| 242 | Providing and fixing Room Heater with Adjustable Thermostat (ISI certified, White colour, Ideal for small to medium room/area) incl all carriages with all leads and lifts as per directions of site incharge complete job |
| 243 | Providing and fixing Micro Automatic Air Conditioners (A.C.) Voltage Stabilizer Upto 1.5 Ton Working Power 170V-270V(Metalic Grey) incl all carriages with all leads and lifts as per directions of site incharge complete job |
| 244 | Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 meters lead :Thickness above 10 mm upto 25 mm |
| 245 | Labor Charges for fixing of CGI sheets by way of cutting, hoisting, fixing in position for walling over structural steel work incl carriage of avilable material from divisinal store to site of work as directed by engineer inchrage |
| 246 | Providing & Fixing of Cocealed warm Lights incl maintenance / replacement period 18 months (10 Watt) |
| 247 | 15 (watt ) |
| 248 | Providing and fixing of 18\\" deep Ward Robes/ Almirah of required size and pattern with 19mm thick Water proof Ply Board fitted with Dalmica including frame Work & fixing of ornamental hinges, Handles, Catchers, adhesive, cornice , beeding & necessary locking arrangements as per the directions of site engineer with all leads,lifts, costs & carriages of all materials involvedupto site of work complete job |
| 249 | Providing /installation of 1.5 ton Hot and cold (Air Conditioner) of approved quality (Blue star /Hitachi/ SAMSUNG/Daiken or equivalent) including providing 5KVA servo stablizer of approved quality with 4 square mm supply line with 32 Amp MCB complete job incld all necassary fixtures as per the directions of Engg. Incharge at site. With all cariages upto site of work all inclusive with cost of material & fitting charges. |
| 250 | Providing and fixing of 18\\" deep Ward Robes/ Almirah of required size and pattern with 19mm thick Water proof Ply Board open rack type and 12 mm thick plyboard on back side incld D type beading fitted with Dalmica on exposed surface including frame Work,all hardware fittings & fixing of adhesive,cornice ,beeding & with all leads, lifts, costs & carriages of all materials involved upto site of work complete job |
| 251 | Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) Including all carriages. |
| 252 | Clearance of Choaked Sewage line/drains by hydraulic high pressure by way of cleaning manholes by mannual/mechanical means including diaposal of rubish,unhygenic material by mannual/mechanical means as per the directions of site engineer. |
| 253 | Engagement of manual Skilled/Un-Skilled labous along with equipment like cutters,axe etc complete Labour/Helper |
| 254 | Carpenter/Mason/Electrician/Welder/Plumber |
| 255 | Providing and commisioning lighting points incld wiring for lighting points in 1.5 Sq.mm PVC insulated copper wire and 2.5 Sqmm PVC insulated multi-strand copper wire for lighting sub mains,6 amp 1 way switch,2 mm thick PVC conduit/Channel with bends,junction boxes etc ,6 amp S Pole MCB ,10 amp DP MCB,2 way DB for housing MCB and hylem sheet of ISI mark and approved make with wooden box recessed in wallls with acessories incld all carriages (concelead type 12 watt) |
| 256 | Providing and commissioning heating point incld wiring for heating points in 2 .5 sq.mm PVC insulated multi-strand copper wire and 4 sq.mm PVC insulated multi-strand copper wire for heating sub-mains, 16 AMP switch socket combine,,2 mm thick PVC conduit/Channel with bends, Junction boxes etc , 10 Amp S pole MCB ,2 way DB for housing MCB and hylem sheet of ISI mark and approved make with wooden box recessed in /over wallls with acessories complete incld all carriages |
| 257 | Providing and commissioning of fan point incld wiring for lighting points in 1.5 sqmm PVC insulated multi strand copper wire,1200 mm ceiling fan /225 mm exhaust fan with ceiling roses and PVC square block ,350 watt electronic fan dimmer, 2 mm thick PVC conduit/Channel with bends, Junction boxes etc, 6 mm S pole MCB ,10 amp DP MCB , 2 way DB for housing MCB for lighting circuits and hylam sheet of ISI mark and approved make with wooden box recessed in wallls with acessories complete incld all carriage and costs of Fan and all other material involved. |
| 258 | Providing and fixing of PVC pipe, fittings(B-Class) of Prince/Phenolex or equivalent make of following size to soil/waste/ventellating pipes as directed by the site Engineer including all carriages. Door bend /Door Junction/Door Tee 100mm |
| 259 | Plain Bend 100mm |
| 260 | PVC Collar100mm |
| 261 | PVC Collar 75mm |
| 262 | Plain Bend 75mm |
| 263 | Floor Trap 100 mm |
| 264 | Door bend /Door Junction/Door Tee 75 mm |
| 265 | Reducer 100x75mm |
| 266 | P or S Trap 100 mm |
| 267 | Door bend /Door Junction/Door Tee 150mm |
| 268 | Providing and fixing of Anodised Alumunium Hardware fittings of approved quality and manufacture with all fittings and fixtures incld.carriages complete (Handles 150 mm) |
| 269 | Tower Bolts 150 mm |
| 270 | Tower Bolts 100 mm |
| 271 | Handles 100 mm |
| 272 | Air hooks |
| 273 | Hire charges for decoration of VIP Lounges/ Buildings on eve of celebration of National days by way of illumination with neon lighting. (All inclusive with hire charges & labour complete job) |
| 274 | Supply of artifical composit marbal/ granite board (16mm thk) as foundation stone of appropriate size, colour and of standard quality with necessary engraving and lettering including fixing in wooden pedestal, finishing, etc. Complete job |
| 275 | P/F of Plastic ready made speed Breaker with heavy duty load capacity black & yellow colors with 50 mm thick 350 mm wide as directed by Engineer incharge including incl cost of cement concrete 1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size) with all carriage etc (complete job). |
| 276 | Instant road patches repairing by way of ready mix pot hole patching premix incl. trench work making proper surface for use (Rectangular & Square patches) incl. compaction complete Job.(cold mix asphalt) road bond or equivalent. As directed by EIC |
| 277 | Hire charges of total station incl Siteplan L-section, x-section, contour,earth work table (Cuttingc& Filling) & other related items complete job |
| 278 | Hire and labours charges for errection of kanth for side pavilion of superior quality/size of superior colour to be erecting prior to function as per requirement on the designated site all complete upto required height upto 8 Ft erected with bamoo posts and tied with ropes including General watch and ward all leads lifts and carriages both sides complete job. Including removal of the same after concluding of function. |
| 279 | Hire and labours charges for errecting of Shamiyana including providing of Crewal on walls and ceiling of required quality with Kanth for VIP stage and fixing with ceiling and pillers including General watch and ward and removal of same after clebration incl. supporting members of bemboo/ pipes tied with ropes and other tools required with hire and labour charge of carpets of superior quality and all carriages to and for all leads and lifts complete required size as directed by Engineer in charge complete job. |
| 280 | Hire and labours charges for errecting of water proof Shamiyanal with bamboo/ pipe posts and tied with ropes and other tools required including lining for sides/ ceiling including with kanath and finished with dragget sheets including general watch and removal of same complete as directed by Engineer in charge complete job. |
| 281 | Hire and laying charges of Tripal including carriages complete as directed by Engineer in charge complete job. |
| 282 | Hire charges for Sofa incl. tables,etc for VIP to be supplied before 24 hours of parade at required site including all carriages to fro complete as directed by Engineer in charge complete job. |
| 283 | Hire charges of PVC chairs with arms (single use) to be supplied before 24 hours of parade at required site including all carriages to fro complete as directed by Engineer in charge complete job. |
| 284 | Supply and installation of Tube lights of aproved make Philips, Havelles, Anchor or equivalent 10 watt |
| 285 | Supply and installation of Tube lights of aproved make Philips, Havelles, Anchor or equivalent 20 watt |
| 286 | Repairing of existing electric fitting points by way of replacing of damaged parts i.e Three pin tops/ Three pin sockets/Switches including replacing of damaged wire Complete. As per the directions of Engg. Incharge at site. Lighting points |
| 287 | Repairing of existing electric fitting points by way of replacing of damaged parts i.e Three pin tops/ Three pin sockets/Switches including replacing of damaged wire Complete. As per the directions of Engg. Incharge at site. Heating Points |
| 288 | Repairing of existing electric fitting points by way of replacing of damaged parts i.e Three pin tops/ Three pin sockets/Switches including replacing of damaged wire Complete. As per the directions of Engg. Incharge at site. Fan Point without fan |
| 289 | Replacing of old Tubular Battery with New Inva Tubular Battery of 200/ 180 AH Ah Capacity Exide, Luminious or equivalent |
| 290 | Supply of Epochem Distilled water for batteries |
| 291 | Supply of PVC insulated wire (copper) of Philips, Alba, Havelles or equivalent 1.50 sqm |
| 292 | 1.00 sqm |
| 293 | 2.50 sqm |
| 294 | Supply of LED Lamps . 7watt, 9 watt of Philips, Alba, Havelles or equivalent |
| 295 | Supply of various electrical accessories of make philips, Alba, Havelles or equivalent S. S Combine 6 AMP |
| 296 | S. S Combine 15 AMP |
| 297 | Switch 6 Amp |
| 298 | Socket 6 Amp |
| 299 | Insulation tape rolls of approved quality |
| 300 | MCB's Philips, Havelles, Anchor or equivalent 6 Amp |
| 301 | MCB's Philips, Havelles, Anchor or equivalent 16 Amp |
| 302 | MCB's Philips, Havelles, Anchor or equivalent 32 Amp D/P |
| 303 | MCB's Philips, Havelles, Anchor or equivalent 40 Amp D/P |
| 304 | MCB's Philips, Havelles, Anchor or equivalent 63 Amp D/P |
| 305 | Supply of PVC Channels (25mm thick) |
| 306 | Repairs and overhauling of Lawn mover HRU-196 complete job including all carriages to and fro. |
| 307 | Supply and installation of LED Flood lights of aproved make Philips, Havelles, Anchor or equivalent 30 watt including maintenance / replacement period 18 months |
| 308 | Supply and installation of LED Flood lights of aproved make Philips, Havelles, Anchor or equivalent 50 watt including maintenance / replacement period 18 months |
| 309 | Suply of Almunium make Folding/ collapsible Ladder of approved quality and make (3 Mtr) height |
| 310 | Suply of Almunium make Folding Ladder of approved quality and make (1.75 Mtr) height |
| 311 | Providing/ Fixing of granite stone slab (18mm thick) of approved quality ( jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent) to be laid over 20mm thick base cement mortar 1:4 (1cement: 4 coarse sand) with joints grouted with white cement mixed with matching pigments, epoxy touchups including rubbing, cutting, moulding and polishing of edges to give high glass finish including providing Reinforced Cement Concrete ( 50-75mm thick) for Slab/ Counter in 1:2:4 mix with cost of reinforcement, half Brick masonary for pillars / partition walls in 1:4 mix including granite skirting for face of pillars and counter and shuttering for RCC counter with cement plaster on brick work in 1:4 mix (1 cement : 4 sand) complete job with cost & carriage of all involved material (work to be executed as per directions of engineer incharge at site. (For payments only top surface area of counter to be measured and paid for ) |
| 312 | Providing and fixing Anodized aluminum grill (Anodized transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved Anodized aluminum standard section around the opening, all complete as epr requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment) |
| 313 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, including Door handle, lock and stopper etc.all complete as per direction of Engineer-in-charge. |
| 314 | Providing and fixing of Exaust fan 350x300 mm of approved quality and make like Bajaj,Havells or equivalent incld. necassary fittings complete job incld. Carriages |
| 315 | Supply ,stacking, filling,laying and spreading of khak bajree in 15 cm layers incld sorting ,spreading to templete ,watering ,dresssing ,ramming and consolidation to the required gradient and camber with 8-10 tonne capacity Power road roller incld. all carriages complete |
| 316 | Clearance of Septic tank by Mechanical/Mannual means including disposal of all un-hygenic material as per the directions of site engineer complete job. |
| 317 | Providing and fixing tiled False Ceiling of specified materials of size 595x595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms/sqm both side inclusive ) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200 x 600mm and secondary cross “T” of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.30mm and laying false ceiling tiles of approved texture in the grid including, wherever, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center to center along size 85x30x0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. (The rate is excluding the cost of tiles which will be paid for separately). including all carriages GI Metal Ceiling Lay in plain Tegular edge Global white colour tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 318 | GI Metal Ceiling Lay in perforated Tegular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece |
| 319 | 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard manufactured from natural gypsum as per IS 2095 part-I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 320 | 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fiber conforming to IS: 2095 part-I, of size 595x595 mm, having perforation of9.7x9.7 mm at 19.4 mm c/c with center borders of 48mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing. |
| 321 | 8 mm thick fully perforated Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/cm2 , bending strength 100 kg/cm2 , of size 595x595 mm, having perforation of dia. 10mm with minimum perforated area 18% with non-woven tissue on the back side, having an NRC (Noise Reduction Certificate) of 0.85, with 50 mm thick rock wool of 48 kg/cum backing. |
| 322 | Labour charges for fixing/ errecting of baracading posts including digging the trenches, refilling and removal of the same after closure of cermony with all carriages to & fro complete. |
| 323 | Labour charges for errecting/ fixing of GI Pipes to barracading posts/ flag pipe including painting of pipes & cost of binding wire, nails etc and removal of the same after closure of cermony with all carriages to & fro complete |
| 324 | Providing & Fixing of flags of different colours (1.00m x 1.00 m size) including return of the same to Divisional store after completion of function. |
| 325 | Providing and spreading of 2nd class sand/silt/Dust in the prade ground to dry up the wet surface of the ground including all carriages upto site of work complete. |
| 326 | Hire charges for supplying and fixing of cultural stage including base, carpet, waterproof pandal with crewel ceiling and sides incl wood flooring with all carriage to and fro complete job (for 02 days) |
| 327 | Hire Charges for Providing & fixing of Pandals with water proof top with crewel ceiling & side curtains of net, Sun shades including all carriages to & fro complete job for 2 days. |
| 328 | Hire charges for supply of Coolers including and controlls complete including all carriages to & fro complete (for 02 days) |
| 329 | Hire charges for Providing of Carpet for stage & VIP Tent 12'x10' including all carriages to & fro |
| 330 | Hire charges for Supply of Red Excel Mating including all carriages to & fro |
| 331 | Providing & Fixing of flex banner (1.00m x 3.25 m size) including writing and monogram & return of the same to Divisional store after completion of function. |
| 332 | Supply of Tricolour cotton Cloth for making banners etc (3x10Mtr) |
| 333 | Providing refreshment to Labours/ Helpers and paticipants for practice (Packed Lunch) at venue site and at Venues . |
| 334 | Refreshment at Venue to the guests & VIP's |
| 335 | Dry fruits & mineral water for VIP's ( Bowls) |
| 336 | Tea with Biscuits/ Kulchas |
| 337 | Roti /Nan/ Cake/ Cocunat/ Bakery Biscuit |
| 338 | Biryani Chicken |
| 339 | Providing and Serving of Tea With snacks |
| 340 | providing and supplying of cotton Towel of approved brand of required size as per the directions of Engineer in charge |
| 341 | Providing & Serving of kehwa with Kulche for VIP’s District officers including hire charges ofCups & accessories |
| 342 | Carriage of material by Mechanical transport from nearest approved source to site of Work |
| 343 | Sand avg.lead-15 kms |
| 344 | Aggregate avg.lead-15 kms |
| 345 | Stones avg.lead-15 kms |
| 346 | Bricks for an avg lead of 65 KMs Please Enable Macros to View BoQ information |