|
| 1 | Part A - Providing and Laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonne per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 percent of mix and filter, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tande, rollers to achieve the desired compaction as per MoRT&H Specifications Clause 509 complete in all respect. |
| 2 | Providing laying, spreading and compactong stone aggregates of specific sizes to water bound uniform thickness, hand packing, rolling with smooth wheel roller 80-100 KN in stages to proper grade and camber applying and brooming, crushable screening to full up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. (page No 4-14) |
| 3 | Providing and applying primer coat with bitumen VG10 on prepared surface of granular Base including of road surface and spraying primer at the rate of 0.70-1.00 Kg/Sqm using mechanical means as per technical specification clause 502 |
| 4 | Providing and applying tack coat with bitumen VG-10 using emulsion pressure distributor at the rate of 0.20 Kg per sqm on the prepated bitumenous/ Granular/ surface cleaned with machanical broom |
| 5 | Providing and laying dense graded bitumenious macadam with 100-120 TPH batch type HMP producing and average output of 75 tonne per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5 percent by weight of total mix and filler, transeporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rolllers to achieve the desired compaction as per MoRT&H Specification Clause 507 Complete in all respects. MORT&H Page no 132 |
| 6 | Road Marking with Hot Applied Thermoplastic Comound with reflectorising glass beads on bituminous surface. Providing and laying of hot app;oed thermoplastic compound 2.5mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35-2015 The finished surface to be level, uniform and free from streaks and holes |
| 7 | Part B - Providing and Laying in position specified grade of reinforced cement concrete, including the cost of centering, shuttering, finishing and excluding reinforcement all work up to plinth level : (a) 1:1.5:3 (1 Cement : 1.5 Coarse sand : 3 graded stone aggregate 20mm nominal size) DSR 5.1.2 |
| 8 | Dismantling reinforced cement conrete or reinforced brick work including stacking of dismantled materials as directed by Engineer-in-Charge within a distance of 60 meters ( 200 feet). Si. 694 part B |
| 9 | Providing and filling in position bitumen mixfiller of proportion 80kg of hot bitumen, 1 Kg of cement and 0.25 cu.M. of coarse sand in expansion joints in width upto 2.5 cm, depth upto 15cm excluding cost of materials but including cost of fuel. Part B |
| 10 | Maintainance of First Year (@0.00% of Total Work Amount of Part A |
| 11 | Maintainance of Second Year (@ 0.25% of Total Work Amount of Part A |
| 12 | Maintainance of Third Year(@ 0.50% of Total Work Amount of Part A |
| 13 | Maintainance of Fourth Year (@ 0.75% of Total Work Amount of Part A |
| 14 | Maintainance of Fifth Year @1.00% of Total Work Amount of Part A Please Enable Macros to View BoQ information |