|
| 1 | Dismantling brick work tile, masonry or tile lining |
| 2 | Dismantling concrete Cement concrete plain 1:4:8 or 1:5:10 |
| 3 | Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled. |
| 4 | Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm. layers with compaction including disposal of all surplus soil as directed within a lead of 30 metres. |
| 5 | Cement Concrete 1:8:16 with 40mm guage stone aggregate using concrete mixing volumetric type |
| 6 | First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth. |
| 7 | First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. |
| 8 | Scraping of Cement Plaster |
| 9 | 12.5mm thick cement plaster 1:4. |
| 10 | 20mm thick cement plaster 1:4. |
| 11 | Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering) |
| 12 | Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc |
| 13 | Reinforced cement concrete M-25 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth |
| 14 | Reinforced cement concrete M-25 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure |
| 15 | Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 550 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including binding, bending and placing in position complete |
| 16 | Tile terracing laid dry over roof consisitng of one layer of tiles 22.86x11.43x3.83 including grouting with cement sand mortar 1:4 top surface to be left clean after wire brushing |
| 17 | Cement concrete 1:2:4 gola 10 cm x 10cm quardrant along junction of roof with parapet wall finished smooth, where specially specified |
| 18 | Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16. |
| 19 | Bottom Khurra on ground 1.2m x 0.6m Mtr. Consisting of brick on edge laid in cement mortar 1:3 over 75mm cement concrete 1:8:16 including 12.5mm thick cement plaster 1:3. |
| 20 | Dismantling cement conglomerate floors 25mm to 50mm thick including concrete base. |
| 21 | Providingand applying Anti Termite Treatment using pre constructional chemical treatment measures as per IS- 6313- 2001(Part 2 )& using Chemical containg chloropyrifos systemic insecticide diluted to manufacturer's specifications (i) In foundationpits, by treating the bottom& sides upto height of 300mmby uniform lyspraying solution@ 5Litre/Sqm (ii) In there fill earth on both sides of all built up walls @ 7.5Litre/Running meter (width-300mm,depth- 450mm ) (iii) Before laying the floor, by uniformly sprinkling the top surface of the consolidated earth with in the outer perimeter @5 Litre solution per Sqm. |
| 22 | Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% taking outside the premises in 15 cm layers including ramming, watering and consolidated lead upto 1000 metres |
| 23 | Cement Concrete 1:4:8 with stone ballast of size. 40 mm guage. using concretemixing volumetric type |
| 24 | Providing and laying vitrified floor tiles in different size in light colour shades made using Full Body Technology (thickness to specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 fine sand ), complete. (Full body vitirified tiles have pigment in entire body/ thickness of which make chips and scratches less noticeable and na ideal choice for high traffic zones) Size 600x600 mm |
| 25 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 26 | Supplying and fixing of Japani sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard design latest), including iron lugs (hold fasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower bolts and finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-chargeDoors and windows frame of size 151mm x 60mm with 35 mm wide double rebate weighing 3.95 kg per meter |
| 27 | Door and window frame of size 113 mm x 60 mm x with 35mm wide single rebate |
| 28 | Factory manufactured solid flush door fixed in position excluding chowkats iron hold fast. Corner straps iron hinges clears and stops etc. (Exculding the cost of any fitting other than specified above but including labour for fixing the same in position). 35mm thick |
| 29 | Hollock wood doors shutter windows shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position. |
| 30 | Wire gauge Hollock wood door shutter without springs housed in chowkhat |
| 31 | Cost of aluminum fittings complete for doors, windows such as tower bolts, handles, Stopper sand screw etc. for these fittings |
| 32 | Wrought iron & Mild steel ladders, framed grills,gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position |
| 33 | Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete. |
| 34 | Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc. |
| 35 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 36 | Preparation of plastered or concrete surface for painting (including sand papering the surface) using Acryllic Wall Putty by applying two or more coats to get required finish including priming coat to make an even surface before applying Acrylic wall putty on new plastered surface. Complete as per specifications |
| 37 | Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface |
| 38 | Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats on old distempered work when shade is changed |
| 39 | Finishing walls with acrylic smooth exterior paintof required shade with two or more coats applied @ 1.67 litre/10Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm |
| 40 | Supplying and fixing glass panes including special metal sash putty of approved make. Glass panes 4mm thick exceeding 0.40sqm area. |
| 41 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In Charge. (Glazing and paneling to be paid for separately) |
| 42 | Providing Polyester Powder coating 50 micron any coloured specified to alumnum section of various sizes including carriage of material from market to workshop & workshop to site of work. |
| 43 | Providing and fixing mineral fibre false ceiling tiles at al heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflection > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mmouter diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6) size 595x595 mm |
| 44 | Providingandfixing 110mmdia.U.P.V.Crain water pipe of 4kgf./sqm as per IS:4985 including jointing during masonary complete as per specifications and to the entire satisfaction of Engineer-in- charge. |
| 45 | Providing and fixing 110 mm dia. U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge |
| 46 | Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete I.S.I Designation No. III (size of door 851mm to 1000mm) |
| 47 | Precast Chequered tiles of 20mm thickness in ordinary grey cement without chips on 20mm thick bed of cement mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps on landings. |
| 48 | Black Granite stone tiles15mm to 20mm thick in skirting, risers of steps,dado walls and pillars laid in12.5mmthickcementmortar1:3(1cement 3 coarsesand)and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour for fixing dowel pins and cramps |
| 49 | Providing & Fixing of Wall panneling |
| 50 | Disposal of malba |
| 51 | Waiting Area |
| 52 | Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm. layers with compaction including disposal of all surplus soil as directed within a lead of 30 metres. |
| 53 | Cement Concrete 1:4:8 with stone ballast of size. 40 mm guage. using concretemixing volumetric type |
| 54 | First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth. |
| 55 | First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. |
| 56 | Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering) |
| 57 | Reinforced cement concrete M-25 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth |
| 58 | Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 550 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including binding, bending and placing in position complete |
| 59 | Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% taking outside the premises in 15 cm layers incluidng ramming, watering and consolidated all lead . |
| 60 | Cement Concrete 1:4:8 with stone ballast of size. 40 mm guage. using concretemixing volumetric type |
| 61 | Providing and laying vitrified floor tiles in different size in light colour shades made using Full Body Technology (thickness to specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 fine sand ), complete. (Full body vitirified tiles have pigment in entire body/ thickness of which make chips and scratches less noticeable and na ideal choice for high traffic zones) Size 600x600 mm |
| 62 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 63 | Providing & Fixing of 40/70 mm Roof PUF(polyurethane foam ) insulated thick Panel with Prepainted Galvanised Ironsheet both sides in 40±2 Kg Density The PU panel shall be CFC( Chlorofluorocarbon)free and Zero Ozone depleting panel using N Pantane blowing agent & made out of continuous line running on uninterrupted power supply. Panel shall have pre coated GI sheet of 0.5mm thickness on both side of Polyurethane Foam confirming to IS 12436:1988. The pre coated sheet shall be of minimum 240 mpa steel grade confirming to IS 14246:1995 and shall have zinc coating of minimum 120 gsm as per IS : 277 : 1992, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 micron. The PPGI sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. The panels shall be vertically joined together by tongue and groove joints. The PU Foam shall be self-extinguishing, fire retardant type having minimum density of 40 Kg/Cu.mt (+, -2 Kgs).The centre to centre pitch of crest profile on top sheet should be between 250mm- 270mm to ensure proper water flow. The roof shall have a projection of minimum 300mm on all sides. Metallic facing sheets are plain with intermediate small ribbed finish on inner skin & Hi Rib sheet as outer skin.(Make: Kingspan Jindal, Sintex, Mectecno,LLoyd insulation) |
| 64 | Providing & Fixing of 80mm Wall PUF(polyurethane foam ) insulated thick Panel with Prepainted Galvanised Ironsheet both sides in 40±2 Kg Density The PU panel shall be CFC( Chlorofluorocarbon)free and Zero Ozone depleting panel using N Pantane blowing agent & made out of continuous line running on uninterrupted power supply. Panel shall have pre coated GI sheet on both side of Polyurethane Foam confirming to IS 12436:1988. The pre coated sheet shall be of minimum 240 mpa steel grade confirming to IS 14246:1995 and shall have zinc coating of minimum 120 gsm as per IS : 277 : 1992, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 micron. The PPGI sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. The panels shall be vertically joined together by tongue and groove joints. The PU Foam shall be self-extinguishing, fire retardant type having minimum density of 40 Kg/Cu.mt (+, -2 Kgs). Surface of steel sheets has plain & light grooves to enhance their strength & aesthetic appearance complete with corner panels as required. (Make: Kingspan Jindal, Sintex, Mectecno) |
| 65 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In Charge. (Glazing and paneling to be paid for separately) |
| 66 | Providing Polyester Powder coating 50 micron any coloured specified to alumnum section of various sizes including carriage of material from market to workshop & workshop to site of work. |
| 67 | Providing and Fixing Single Glazing with 6mm thick glass with high performance coating as per relevent codal provisions as per satisfaction of Engineer-in-Charge. |
| 68 | Providing and fixing mineral fibre false ceiling tiles at al heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflection > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mmouter diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6) size 595x595 mm |
| 69 | 20mm thick cement plaster 1:4. |
| 70 | Preparation of plastered or concrete surface for painting (including sand papering the surface) using Acryllic Wall Putty by applying two or more coats to get required finish including priming coat to make an even surface before applying Acrylic wall putty on new plastered surface. Complete as per specifications |
| 71 | Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface |
| 72 | Finishing walls with acrylic smooth exterior paintof required shade with two or more coats applied @ 1.67 litre/10Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm |
| 73 | Barricading |
| 74 | Wrought iron & Mild steel ladders, framed grills,gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position |
| 75 | Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc. |
| 76 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 77 | Sub Work 1 |
| 78 | Sub Head-1 Internal Sewerage System |
| 79 | Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing.Single Socket Type B110mm o/d SWR UPVC pipe lines laid complete |
| 80 | Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. |
| 81 | For 110mm i/d pipes |
| 82 | Elbow 90 Degree (All side socketed) |
| 83 | Vent Cowls |
| 84 | Coupler |
| 85 | Single Tee With Door |
| 86 | P Trap/floor Trap 110mmx 110mm |
| 87 | Cement Concrete 1:2:4 with stone ballast or shingle mixing by mannual means |
| 88 | Providing PVC solvent cement joints to SWR Pipes and specials including cost of PVC solvent cement and tools etc of approved make (to the approval of Engineer-in-charge)110mm o/d |
| 89 | Providing & Fixing in position M.S or heavy flat iron clamps made out of M.S flat iron not less than 5 mm of the approved design for fixing C.I. soil waste, vent or antisyhonage pipes to walls complete in all respects including cutting and making good the walls and floors etc. and painting. M.S. Holder bats clamps for 100mm i/d |
| 90 | Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm.100mm internal Diametre S.W. gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm |
| 91 | Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, C.C.1:4:8 ( 150mm thick) in foundation, cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside R.C.C. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design. 450mm x 450mm inside with 455mm x 455mm cover and frame light duty double seal |
| 92 | Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Type A, Lines as per ISI 4985-2021, including specials such as tees, bends, sockets, elbow etc., cutting, testing (including cost of specials) in the ground complete in all respects.uPVC Pipe 6 Kgf/cm250mm i/d |
| 93 | Sub Head-2 Internal Water Supply System |
| 94 | CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in- Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge. |
| 95 | SDR 11 CPVC pipes & fittings 20mm o/d |
| 96 | CPVC SDR 11 Pipe & fitting 25mm o/d |
| 97 | Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes lines and making good the same to its original condition. Size 75mm x 75mm |
| 98 | Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required. |
| 99 | Through wall 11.43 cm thick |
| 100 | Through wall 22.86 cm thick |
| 101 | Providing, fixing and jointing Upvc Union Couplings with Upvc Pipes complete in all respect.25mm i/d Union |
| 102 | Providing, fixing and jointing CPVC Ball valves screwed with CPVC ball & spindle & Teflon seats, on CPVC Pipe lines including all carriages complete. |
| 103 | 20mm i/d CPVC Ball valves |
| 104 | 25mm i/d CPVC Ball valves |
| 105 | Sub Head - 3 Sanitary Installation |
| 106 | Providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 107 | Providing and fixing in position stainless steel sinks of approved make (to the approval of Engineer-in-charge) 1mm thick,grade-304 (18/8) with waste coupling complete in all respect.Double bowl Sink without drain board Overall size 1114 x 490 mm with bowl size 460x385x200mm including waste coupling |
| 108 | Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect. PVC tube connection of size 15 mm x 375 mm with PTMT nut |
| 109 | Providing and fixing P.V.C Waste Pipe Collapsible 32mm complete in all respect. |
| 110 | Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge ) complete in all respect.C.P. Brass Fittings: |
| 111 | C.P.brass 15mm Angular stop cock withWall flange |
| 112 | C.P brass Sink mixer with swingingspout.(wall mounted) |
| 113 | Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect. |
| 114 | Providing & Fixing in position C.P. Brass extension piece 25mm long to 100mm long of approved make (to the approval of Engineer-incharge )with various fixtures complete in all respect.C.P. Brass extension piece, 25mm long to 50mm long |
| 115 | Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. Tripple Layer Tanks |
| 116 | Providing and fixing in position CPVC Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect.CPVC Tank nipple 25 mm i/d |
| 117 | Construction of Plateform complete as per specification & as desired by Enginer-in-chargeFor 500 ltr Water Tank |
| 118 | Providing and fixing in postion storage type automatic electric water heater pressure type thermostatically controlled, single phase wall mounted of approved make (to the approval ofEngineer-in-charge) with thermostats, inner container of stainless steel, Inner glass liningwith B-Rating minimum 3 stars complete with 1 Mtr. three core flexible cord with plug, non returnvalve and pressure release valve complete including fixing and testing complete in allrespect. 15 litre capacity water heater Vetical Type 15 litre capacity water heater |
| 119 | Sub Head -4 Drinking Water Coller |
| 120 | Providing & fixing in position Water Cooler without Stablizer of approved make (to the approval of Engineer-in-charge ) including carriage complete in all respect. |
| 121 | Water Cooler Semi Steel Body 80/120 ltrCapacity without StablizerDetail as per Table-3 |
| 122 | Providing & fixing in position Commercial RO without reservoir with four no cartridge/membrane having flow rate 50 ltr/hr with 6 stage purification process of approved make(to the approval of Engineer-in-charge ) including carriage and fixing in positioncomplete in all respect. |
| 123 | Providing & fixing in position Water Dispenser Top Loading (with refrigration capacity 15 ltr)of approved make (to the approval of Engineerin- charge ) dispensing hot/cold/ambient waterincluding cost of two no. 20 ltrs packaged drinking water bottles and carriage complete inall respect. |
| 124 | Sub Work - 2 |
| 125 | Estate Sewerage |
| 126 | Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked make Supreme, Finolex, Kissan, Jain, Prince or equivalent good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects.110 mm o/d pipes |
| 127 | Excavation in trenches with straight or open cutting in streets, lanes or in open area with 3D/JCB or excavator including manually dressing bed, trimming sides and side slopes for sewers and manholes to full depths as shown in drawings,including, dressing to correct sections and dewatering, provision for diversion for traffic, protection of existing services i.e. telephone cables, electric lines, water supply lines and gas lines etc. night signals, profiles, pegs, sight rails, boning rods, watching, etc., fixing and maintenance of caution boards, fencing, refilling trenches, watering, ramming and restoration of surface to original level and removal of surplus spoil from the site of works, upto one chain (15m) complete in all respects.For depth exceeding 3.00 m but not exceeding 4.5 B.G.L.All kinds of soil except rocky |
| 128 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:2 (1 cement : 2 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete. For pipes 100 to 250 mm Diametre |
| 129 | Air Conditioning |
| 130 | Providing & Installing & Erection split type wall mounted inverter type air conditioner capacity 1.5 tonne 5 Star 5000 W cooling capacity of reputed Make with 4.00 KVA voltage stablizer, MCB arrangement for installing OD units on terrace including inlet and outlet copper tubes with proper insulation drainage arrangement cable link between ID unit and OD units stand for OD unit and connection of 3 mtr concealing Copper pipes within building and installing charges complete in all respects |
| 131 | Providing, laying, jointing & fixing drain pipe required at site as per site condition.For 1.50 tonne split AC |
| 132 | Electrical Services:- RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: |
| 133 | Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½\\" deep for walls and CI 3\\" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- |
| 134 | Wiring fan point (Without fan box) |
| 135 | Wiring light point |
| 136 | Wiring call-bell point |
| 137 | Wiring 6Amp. wall socket point |
| 138 | Wiring 6Amp. Plug control comprising wall socket point |
| 139 | Wiring 16/20Amp. power plug control point |
| 140 | Wiring light point with double control switches. |
| 141 | RECESSED AIR CONDITIONER SUPPLY TERMINAL POINT (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): |
| 142 | Wiring air conditioner supply terminal point recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 25Amp. combined/ universal Socket (shuttered) and modular motor starter 25Amp. (2Module), covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):-Wiring AC supply terminal point having 1No. 25Amp. universal Socket (shuttered) erected at AC height and 1No. Motor starter 25Amp. erected at switchboard height. |
| 143 | RECESSED COMPUTER SUPPLY TERMINAL POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): |
| 144 | Wiring Computer supply terminal points recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10/16/20Amp. Switches and blanking plate etc., and covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):-Wiring Computer terminal point having 3 Nos. 6Amp. 2/3 universal socket (shuttered), 1No. 16 Amp. switch with indicator and 1No. blanking plate (Modular accessories). |
| 145 | RECESSED TV, TELEPHONE & NETWORKING SOCKETS OUTLET POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): |
| 146 | Supply and erection of TV socket, Telephone socket and Networking socket points in powder coated/anodized concealed metal boxes recessed in wall required for suitable number of modules (Modular accessories) for having TV sockets, Telephone sockets RJ11 & Networking socket RJ45 (one module), covered with Frame Plate and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- |
| 147 | Wiring Telephone socket point RJ11 (one module) |
| 148 | Wiring Networking socket point RJ45 (one module) |
| 149 | SURFACE AIR CONDITIONER SUPPLY TERMINAL POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): |
| 150 | Supply and erection of air conditioner supply terminal point on surface on wall etc., complete with PVC boxes (Plastic on surface boxes) required for suitable number of modules (Modular accessories) for having 25Amp. combined/ universal Socket (shuttered) and modular motor starter 25Amp. (2 Module), covered with Frame Plate etc., & including the cost of above material and other petty material with necessary connections etc.:-Wiring AC supply terminal point having 1No. 25Amp. universal Socket (shuttered) erected at AC height and 1No. Motor starter 25Amp. erected at switchboard height. |
| 151 | SURFACE COMPUTER SUPPLY TERMINAL POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): |
| 152 | Wiring Computer supply terminal points on surface on wall etc., complete with PVC boxes (Plastic on surface boxes) required for suitable number of modules (Modular accessories) for having 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10/16/20Amp. Switches and blanking plate, covered with Frame Plate etc., & including the cost of above material and other petty material with necessary connections etc.:-Wiring Computer terminal point having 3 Nos. 6Amp. 2/3 universal socket (shuttered), 1No. 16 Amp. switch with indiicator and 1No. blanking plate |
| 153 | PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE: |
| 154 | Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- |
| 155 | Overall size 1.5sq.mm (Un-sheathed) |
| 156 | Overall size 2.5sq.mm (Un-sheathed) |
| 157 | Overall size 4sq.mm (Un-sheathed) |
| 158 | Overall size 6sq.mm (Un-sheathed) |
| 159 | Overall size 10 sq.mm (Un-sheathed) |
| 160 | Overall size 16 sq.mm (Un-sheathed) |
| 161 | COPPER CONDUCTOR CABLES FOR SPECIAL ELECTRICAL SERVICES: |
| 162 | Supply and erection of CAT 6 with 23AWG solid bare copper conductor, special grade PE insulation with star separator, 4pair Unshielded Twisted Pair (UTP) industrial cable, FR PVC sheathed, Class-E, 250 MHz of bandwidth, supporting data transfer speeds of up to 10 Gbps (10GBASE-T) for distances up to approximately 180 feet, cables are manufactured and tested to meet the ANSI/TIA 568-C.2 and ISO/IEC 11801 Class E standards left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-CAT 6 LAN cable |
| 163 | XLPE INSULATED UN-ARMOURED CABLES (ON SURFACE): |
| 164 | Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:-Overall size 25sq.mm (3½ Core) Un-armoured (On-Surface) |
| 165 | HEAVY GAUGE WELDED CONDUIT PIPES: |
| 166 | Supply & erection of Heavy guage welded conduit pipe (ISI marked) as per IS:9537:Part-II for wiring purposes including bends, junction boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications:-Supply & erection of 19/20mm dia. M.S. conduit pipe (1.6mm thick), White painted suspension rod for ceiling fan. |
| 167 | PVC, HDPE PIPES & PVC FLEXIBLE PIPES: |
| 168 | Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- |
| 169 | Heavy Gauge PVC Conduit Pipe 25mm dia. (Flushed) |
| 170 | Heavy Gauge PVC Conduit Pipe 32mm dia. (Flushed) |
| 171 | Heavy Gauge PVC Conduit Pipe 25mm dia. (On Surface) |
| 172 | Heavy Gauge PVC Conduit Pipe 32mm dia.(On Surface) |
| 173 | COPPER EARTHING: |
| 174 | 8 SWG COPPER EARTHING : |
| 175 | Earthing with 8 SWG (4mm dia.) electrolytic copper wire thimbled (1No. copper thimble with suitable size steel bolt, washers & double nut) with 30cm x 60cm x 2mm thick copper plate (made cylindrical) burried below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) recessed in wall and in floor etc., up to suitable Length in metre (including bore Length). G.I. pipe 20mm dia. (A-class) of suitable Length should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:- |
| 176 | Earthing with 8 SWG (4mm dia.) copper wire thimbled with 30cm x 60cm x 2mm thick copper plate burried 4.50 metre (14.76 feet) below ground level (up to 8metre in Length) with G.I. pipe 20mm dia. (A-class), 3metre long |
| 177 | Fixing additional Length of earthing with 8 S.W.G. (4mm dia.) copper wire in G.I. pipe with sockets, elbows, steel hooks and GI saddle clamps including painting etc.:-Additional Length copper wire 8 S.W.G. (4mm dia.) in 20mm dia. G.I. pipe (Flushed) |
| 178 | SUPPLY AND ERECTION OF WIRING ACCESSORIES: |
| 179 | Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.:- |
| 180 | Bakelite Batten Holder (Large size) |
| 181 | Ceiling Rose (Flush Piano type) |
| 182 | Call Bell 220/230 volts AC Ding Dong |
| 183 | MINIATURE CIRCUIT BREAKERS: |
| 184 | Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- |
| 185 | MCB Single Pole 6-32amp. (10kA, Curve-C) |
| 186 | MCB Double Pole 40amp. (10kA, Curve-C) |
| 187 | MCB Triple Pole 40amp. (10kA, Curve-C) |
| 188 | MCB Triple Pole 50, 63amp. (10kA, Curve-C) |
| 189 | MCB Four Pole 50, 63amp. (10kA, Curve-C) |
| 190 | SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB's/ RCBO's/ RCCB's: |
| 191 | Supply and erection of sheet metal Double Door Distribution Boards IP 43-IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, color-coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:- |
| 192 | SP&N Double Door Distribution Board 8 way each |
| 193 | TP&N Horizontal Double Door Distribution Board 6 way each |
| 194 | Supply and erection of sheet metal double door vertical distribution boards IP 43-IK09 metal door (dust protected) as per IS:8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars for each phase, 2 Nos. shrouded neutral bars, 2Nos. earth bars, cement spill protector, color-coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting MCCB's as incomer and outgoings SP/TP miniature circuit breakers in the distribution board as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc.:-TP&N Double Door Vertical DB's 4 way each (With provision of FP MCCB upto 125amp) |
| 195 | SHEET METAL IRON CLAD SWITCHES: |
| 196 | Supply and erection of sheet metal Iron Clad Switches on existing surface with G.I. bolts & nuts/ rag bolts and nuts etc., according to the size of holes in the body of the enclosure including connections with suitable size of thimbles and bonding to the existing earth as Per PWD General Specifications:-ICTPN Switch 100amp., 415volts |
| 197 | SHEET METAL BUS BAR CHAMBERS (COPPER STRIPS): |
| 198 | Supply and erection of sheet metal bus-bar chamber (factory fabricated) duly powder coated on existing surface with required 4Nos. of tin plated copper bus-bar strips of suitable length and cross-sectional area mounted on DMC/ SMC moulds at sufficient distance, enclosure made of M.S. sheet 1.6mm thick with hinged cover and lock, fitted with dust excluding gaskets and secured with sufficient no. of cadmium plated iron screws and of given overall dimensions and to be fixed with G.I. bolts and nuts/ rag bolts and nuts etc. complete with all accessories including connections with suitable size of thimbles, bonding to the existing earth and painting etc. as desired by the Engineer-in-charge at site:-Bus Bar Chamber 100amp., 415volts Overall Dimensions (350mm x 450mm x 150mm) nominal |
| 199 | ON LOAD CHANGEOVER SWITCH (With Sheet Enclosure): |
| 200 | Supply and erection of On Load Change over Switch with advance neutral UNIT in sheet enclosure on the existing surface. (Confirms to IS 13947 (Part-3). complete with G.I. Bolts, Nuts etc. according to the size of holes in the body of the enclosure & Connections on both sides of switch with suitable size of thimbles as per PWD General Specifications:-On Load Change Over Switch Four Pole 100amp., 415volts (With Sheet Enclosure) |
| 201 | MCCB's (MOULDED CASE CIRCUIT BREAKER): |
| 202 | Supply and erection of Moulded Case Circuit Breaker (Panel mounting Cubical type) in the existing Cubical Panel (confirm to IEC:60947-2) having Ics=100% Icu, 100% neutral with spreader links and relevant PWD general specifications complete with G.I. Bolts, Nuts & Connection on both sides of MCCB with suitable size of thimbles etc:-MCCB Four Pole 125amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting |
| 203 | MS SHEET ENCLOSURE FOR MCCB's: |
| 204 | Supply & Erection of indoor type MCCB enclosure of suitable size having provision for MCCB with extended rotary handle. The Enclosure shall be made from 14/16 SWG CRCA sheet, confirming to IS 8623/1977-82. The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The Enclosure door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. The Enclosure will be wall mounting type having provision for cable entry from bottom/top with cable glands etc. The sheet metal is sprayed with corrosion resistant etch primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work:- MS Sheet Enclosure having provision for MCCB 40-160Amp.with extended rotary handle (Approx. Size 500mm x 300mm x 200mm) |
| 205 | Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1/2mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-Double Walled Corrugated HDPE Pipe 63/ 51mm (Outer/ Inner dia.) |
| 206 | Supply and erection of LED batten 20 Watt LED (including constant LED driver) with High quality extruded aluminium with efficacy of LED fixture minimunm 100 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection IP20 (as per latest BIS standards) surge protection - 2.5 KV and above (as per IS/IEC standards) wattage of each low power LED less than 1 watt input AC frequency 50 Hz ± 3 % with 5 year warranty including there drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site. LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter ION No: AT/2021/GL/1410-1422, Dated: 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited laboratory. |
| 207 | Supply and erection of LED batten 40 Watt LED (including constant LED driver) with High quality extruded aluminium with efficacy of LED fixture minimunm 100 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection IP20 (as per latest BIS standards) surge protection - 2.5 KV and above (as per IS/IEC standards) wattage of each low power LED less than 1 watt input AC frequency 50 Hz ± 3 % with 5 year warranty including there drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site. LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter ION No: AT/2021/GL/1410-1422, Dated: 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited laboratory. |
| 208 | Supply and erection of Recessed mounted 36watt LED 2x2 panel, Supply Voltage 140-270Volts AC supply, 50Hz ± 3% (including BIS Certified potted single diver with screen or laser printing logo LED driver) with CRCA sheet with control gear (IP 20 protection), THD<10%, CRI minimum 70, Low power LED with wattage Less 1 Watt, Surge Protection 2.5KV and above as per IS/ IEC Standards, efficacy of LED fixture minimum 100 lumens per watt, 5 year warranty including their drivers complete in all respects as approved and desired by the Engineer in-charge at site. LED Fittings as per specifications approved by Hon'ble Technical Advisor to Punjab Govt. vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufacturers should have in house NABL accredited lab |
| 209 | Supply and erection of Ceiling Fans 1200 mm Sweep (48\\") 3 Star having two ball bearing including flexible wire & petty material etc.complete in all respects as appd. and desired by the Engineer in-charge at site. |
| 210 | Supply and erection of Wall Fan Plastic Body 400MM, 16\\" including flexible wire & petty material etc. for connections and testing complete in all respect as approved and desired by the Engineer in-charges at site. |
| 211 | Supply and erection of Heavy duty Exhaust Fan 300mm, 900RPM with aluminium louver shutter, double ball bearing longer life including flexible wire & petty material etc. for connections and testing complete in all respect as approved and desired by the Engineer in-charges at site. |
| 212 | Providing Conference sytem |
| 213 | Supply and erection of AHUJA CMC 5100 CHAIRMAN MIC COMPLETE. |
| 214 | Supply and erection of AHUJA CMD 5200 DELEGARE MIC COMPLETE. |
| 215 | Supply and erection of AHUJA CMA 5400 PA SYSTEM COMPLETE. |
| 216 | Supply and erection AHUJA WIRELESS MIC QWM495V2 COMPLETE. |
| 217 | Supply and erection AHUJA SPEAKER SCM 15 T COMPLETE. |
| 218 | Supply and erection Cable WireCOMPLETE. |
| 219 | Service Charges |
| 220 | Providing Additional CCTV Cameras and LED TV to Existing 16 Channel NVR |
| 221 | Supply, Installation, Testing & Commissioning of STQC Approved 5MP IP WDR IR Rugged Mini Dome Camera. Operational Video Standard NTSC/PAL, Scanning System: Progressive, Image Sensor: 1/2.7\\" Progressive CMOS, Number Of Pixels (H x V): 2560(H) x 1920(V), Minimum Illumination: 0.03 lux color @ F2.0, 0 lux B/W with IR LEDs on @ F2.0, S/N Ratio > 55 dB, Electronic Shutter Speed 1/5 ~1/32.000, IR Distance: Distance up to 30m (98ft), IR Light Control: Smart IR (Auto/Manual)/OFF, IR Light Number 2, Day/Night: Auto/Day/Night/Schedule, Backlight Compensation WDR, HLC, White Balance: Auto/Fixed Current/Manual, Gain Control: 0-100%, Wide Dynamic Range: 120dB, Noise Reduction 3D DNR, Privacy Masking: Off / On (5 Areas). Motion Detection Motion/Intrusion/People detection, Tampering Detection: Tampering Detection/Image too dark detection/Image too bright detection/Image too blurry detection, Region Of Interest Support, Lens 2.8mm, Fixed, F2.0, Angle Of View H:103\\", V:76 @5M, Video Compression H.265/H.264/Smart Codec/MJPEG, Resolution (5MP): 2560x1920/2048x1536/ 1600x1200/1280x960/800x600/640×480; Frame Rate Main Stream: 5M/4M (1 ~ 25/30fps): \\"Up to 30fps @SM under H.265 onlySub Stream: 800x600 (1 ~25/30fps); Third Stream: VGA (1- 25/30fps). Bit Rate Control: Constrained bit rate/Fixed quality, Bit Rate 20K ~ 40Mbps, NETWORK: Ethernet 10 Base-T/100 Base-TX Ethernet (RJ-45), Supported Web Browsers Chrome 71+, Internet Explorer 11.0+ Supported OS Microsoft windows 7/10, Protocols IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP, TSP/RTP/RTCP, IGMP, SMTP, DHCP, NTP, DNS, DDNS, CoS, QoS, SNMP, 802.1X, UDP, ICMP, ARP, TLS, Interoperability ONVIF Profile G/S, Maximum Users Access 10 Users, approved make should have honeywell, axis, bosch Security User account and password protection, HTTPS, IP Filter, Digest authentication, TLS1.2 only, Stream encryption, AES-128/256, SSH/Telnet closed, PCIDSS NDAA compliance, Event: Event notification using HTTP, SMTP, NAS server and MicroSD cardFile upload via HTTP, SMTP, NAS server and MicroSD card, Micro SD/SDHC/SDXC card slot (256GB): ELECTRICAL Power Supply DC12V, PoE (IEEE 802.3af) (Class 2), Power Consumption MAX 6.49W, MECHANICAL: Dimensions 117.11mm x 69.51mm (Ø4.61\\" x3.52\\"), Product Weight 0.54kg, Package Weight 0.88kg, Material Die-casting aluminum housing with coating, Construction Color RAL 120-1 (Lyric White), ENVIRONMENTAL: Operating Temperature Starting: -10°C ~ 60°C (14°F ~ 140°F)Working -30°C ~ 60°C (-22°F ~ 140°F). Relative Humidity Less than 90%, non- condensing, Ingress Protection IP66, Vandal Resistance IK10, REGULATORY: Emissions FCC PART 15B, EN 55032, EN61000-6-3, Immunity EN 50130-4, Safety UL 62368-1, EN 62368-1 ROHS, EN 50581 Complete in all respect to the entire satisfaction of the engineer-in-charge. complete in all respect as approved and desired by Engineer in-charge at Site. |
| 222 | Supply, Installation, Testing & Commissioning of 43 \\" 4k UHD TV Resolution 3840 x 2160 ,,Built-in Speaker (10W + 10W) complete in all respects as approved and desired by the Engineer-in-charge at site. |
| 223 | Supply, Installation, Testing & Commissioning of HDMI Splitter Cum Extender 4 Port .The HDMI Splitter cum Extender is a device that splits the Hdmi input signals into 4 Hdmi outputs and also extends the 4 Hdmi signals at thr same time. The Marx HDMI Splitter cum Extender has 1 tansmitter and 4 receivers,which splits and extends the Hdmi signals Complete in all respect to the entire satisfaction of the engineer-in-charge. |
| 224 | Supply, Installation, Testing & Commissioning of STQC Approved 5 MP IP WDR IR Bullet Camera OPERATIONAL Video Standard NTSC/PAL Scanning System: Progressive, Image Sensor. 1/2.7\\" Progressive CMOS, Number Of Pixels (H x V): 2560(H) x 1920(V), Minimum Illumination: 0.03 lux color @ F2.0, 0 lux B/W with IR LEDs on @ F2.0, S/N Ratio: > 55 dB, Electronic Shutter Speed: 1/5 - 1/32.000, IR Distance: Distance up to 50m (165ft), IR Light Control: Smart IR (Auto/Manual/OFF. IR Light Number 2, Day/Night: Auto/Day/Night/Schedule, Backlight Compensation WDR, HLC, White Balance: Auto/Fixed Current/Manual, Gain Control 0-100%, Wide Dynamic Range 120dB, Noise Reduction 3D DNR, Privacy Masking Off On (5 Areas), Motion Detection: Motion/Intrusion/People detection, Tampering Detection: Tampering Detection/Image too dark detection/Image too bright detection/ Image too blurry detection, Region Of Interest Support, Lens: 4 0mm, Fixed, F2.0 Angle Of View: H:78\\", V:59 @5M, Video Compression H.265/H.264/Smart Codec/MJPEG, Resolution 2560x1920/2048x1536/ 1600x1200/1280x960/800x- 600/640x480: Frame Rate: Main Stream: 5M/4M (1~25/30fps); 'Up to 30fps @5M under H.265 only Sub Stream: 800x600 (1~25/30fps): Third Stream: VGA (1~25/30fps), Bit Rate Control: Constrained bit rate/Fixed quality, Bit Rate 20K-40Mbps Ethernet 10 Base-T/100 Base-TX Ethernet (RJ-45). Supported Web Browsers Chrome 71+, Internet Explorer 11.0+, Supported OS Microsoft Windows 7/10, Protocols IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP, RTSP/RTP/RTCP, IGMP, SMTP, DHCP, NTP, DNS, DDNS, COS, QoS, SNMP, 802.1X, UDP, ICMP, ARP, TLS. Interoperability ONVIF Profile G/S, Maximum Users Access: 10 Users, approved make should have honeywell, axis, bosch Security User account and password protection, HTTPS, IP Filter, Digest authentication, TLS1.2 only, Stream encryption, AES- 128/256, SSH/ Telnet closed. PCIDSS, NDAA compliance, Event notification using HTTP, SMTP, NAS server and MicroSD card File upload via HTTP, SMTP, NAS server and MicroSD card Micro SD: Micro SD/SDHC/SDXC card slot (256GB Power Supply DC12V, POE (IEEE 802.3af) (Class 2) Power Consumption MAX 6.49W. Dimensions 091.1mm x 177mm (ø3.59\\" x 6.97\\"), Product Weight 0.53kg, Package Weight 0.74kg. Material Die-casting aluminum housing with coating, Construction Color RAL 120- 1 (Lyric White), Operating Temperature Starting: -10°C~60°C (14°F-140°F) Working: -30°C- 60°C (-22°F 140°F). Relative Humidity Less than 90%, non-condensing, Ingress Protection IP66, Emissions FCC PART 15B, EN 55032, EN61000-6-3, Immunity EN 50130-4, Safety UL 62368-1, EN 62368-1, ROHS EN 50581 Complete in all respect to the entire satisfaction of the engineer-in-charge. complete in all respects as approved and desired by the Engineer-in-charge at site |
| 225 | Supply & Erection of 2KVA 24V pure Sine Wave Invertor with 2 No. 150 Ah Batteries along with erection of the same with connections, including warrenty and service for one years complete in all respect as desired by the engineer in charge at site.Complete in all respect as desired by the Engineer In Charge. |
| 226 | Supply, Installation, Testing & Commissioning of HDMI CABLE 40 MTR | 4K Fiber, HDMI to HDMI Cable | 40M, Active Optical Cable, Ultra HD 2160P 18Gbps HDMI 2.0 Cord Supports 4K@60Hz, 10 HDR for TV, Laptop, PC, Projector (Black) 40Mtr. Complete in all respect to the entire satisfaction of the engineer-in-charge. |
| 227 | Supply, Erection, Testing & Oil filled Room Heater 9 fins 230 v with 1 year warranty etc. Complete in all respect as desired by the Engineer In Charge Please Enable Macros to View BoQ information |