|
| 1 | CIVIL WORK |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 3 | All kinds of soil. |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 5 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level |
| 7 | 1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 8 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) |
| 9 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 10 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6graded stone aggregate 20mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth |
| 11 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. And above PL LVL. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 12 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per 1S: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. |
| 13 | All works above plinth level upto floor V level |
| 14 | Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 16 | Foundations, footings, bases of columns, etc. for mass concrete. |
| 17 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 18 | Suspended floors, roofs, landings, balconies and access platform. |
| 19 | Shelves (Cast in situ) |
| 20 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 21 | Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 22 | Weather shade, Chajjas, corbels etc., including edges |
| 23 | Edges of slabs and breaks in floors and walls |
| 24 | Under 20 cm wide |
| 25 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 26 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 27 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 28 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 29 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of V class designation 7.5 in superstructure above plinth level up to floor level. |
| 30 | Cement mortar 1:4 (1 cement :4 coarse sand) |
| 31 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 32 | Providing and fixing 18mm thick gang saw cut ( premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. |
| 33 | Granite of any colour and shade |
| 34 | Area of slab over 0.50 Sqm.( For Counter) |
| 35 | Extra for fixing marble / granite stone over and above corresponding basic item, in facia and drops of width upto 150mm with epoxy resin baesd adhesive including cleaning etc. complete. |
| 36 | Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/Stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edge etc. complete. |
| 37 | Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 38 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 39 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 40 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 41 | 300x16 mm |
| 42 | 250x16 mm |
| 43 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 44 | 250x10 mm |
| 45 | 150x10 mm |
| 46 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 47 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 48 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings,glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). |
| 49 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 50 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 51 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 52 | 125 mm |
| 53 | 100 mm |
| 54 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 55 | Single rubber stopper |
| 56 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 57 | Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 58 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows, Doors and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.With 12 mm mild steel U beading |
| 59 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : |
| 60 | Float glass panes |
| 61 | 4 mm thick glass pane (weight not less than 10kg/sqm). |
| 62 | 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). |
| 63 | Steel work welded in built up section / frame work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 64 | In grating, frames, guard bar, ladder, railing, brackets, gates and Similar work. |
| 65 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1: 4 (1 cement : 4 coarse sand) : |
| 66 | Providing and laying 25 mm. thick kotah stone tile in risers of steps, skirting and pillars of approved size, texure and colour laid over 12 mm. thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to matched the shade of the slab including rubbing to granolithic finish with approved quality. |
| 67 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 68 | Extra for Kota stone/ sand stone in treads of steps and risers using single length above normal size up to 2.00 metre. |
| 69 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sgm including pointing the joints with white cement and matching pigments etc., complete. |
| 70 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to 1S: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 71 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to 1S:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 72 | Glazed vitrified floor tiles polished finish of size |
| 73 | Size of Tile 600x600 mm |
| 74 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 75 | Size of Tile 600x600 mm |
| 76 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 77 | 12 mm cement plaster of mix : |
| 78 | 1:6 (1 cement: 6 coarse sand) |
| 79 | 15 mm cement plaster on rough side of single or half brick wall of mix: |
| 80 | 1:6 (1 cement: 6 coarse sand) |
| 81 | 6 mm cement plaster of mix: |
| 82 | 1:3 (1 Cement : 3 Fine Sand) |
| 83 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 84 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/liter, of approved manufacturer and of required shade and colour all complete to achive even shade and colour : |
| 85 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 86 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: |
| 87 | New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 88 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : (On steel work) |
| 89 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 90 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: |
| 91 | (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). |
| 92 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality |
| 93 | H D - 20 |
| 94 | Circular shape 560 mm internal diameter |
| 95 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 96 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 97 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : |
| 98 | With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 99 | Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : |
| 100 | With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 101 | SANITARYWORK |
| 102 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. |
| 103 | 20 mm nominal dia Pipes |
| 104 | 25 mm nominal dia Pipes |
| 105 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. |
| 106 | 25 mm nominal dia Pipes |
| 107 | 32 mm nominal dia Pipes |
| 108 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 109 | 15 mm nominal bore |
| 110 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 111 | 15 mm nominal bore |
| 112 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 113 | 15 mm nominal bore |
| 114 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Flexible pipe. |
| 115 | 32 mm dia |
| 116 | Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length |
| 117 | 15 mm nominal bore |
| 118 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 119 | 20 mm nominal bore |
| 120 | Providing and fixing brass stop cock of approved quality |
| 121 | 20 mm nominal bore |
| 122 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 123 | 25 mm nominal bore |
| 124 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required |
| 125 | W.C. pan with ISI marked white solid plastic seat and lid |
| 126 | Providing and fixing toilet paper holder |
| 127 | C.P. brass |
| 128 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 129 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 130 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 131 | 150 mm diameter |
| 132 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : |
| 133 | Rectangular shape 453x357 mm |
| 134 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 135 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 136 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : |
| 137 | For 100 mm dia pipe |
| 138 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 139 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 140 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 141 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour |
| 142 | 20 mm nominal bore, weighing not less than 40 gms |
| 143 | Providing and fixing PTMT grating of approved quality and colour circular type. |
| 144 | 100 mm nominal dia |
| 145 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 146 | Coupler 110 mm |
| 147 | Shoe (Plain) 110 mm Shoe |
| 148 | Bend 87.5° (110 mm bend) |
| 149 | Single tee with door (110x110x110 mm) |
| 150 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 151 | 110 mm diameter |
| 152 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required |
| 153 | Kitchen sink with drain board (510x1040 mm bowl depth 250 mm) |
| 154 | ELECTRICAL WORK |
| 155 | Wiring for light point / fan point /exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC Conduit, with modular switch,modular plate ,suitable GI Box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 156 | a) Group B |
| 157 | Wiring for group controlled (looped) light poinVfan poinVexhaust fan poinV call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required |
| 158 | a) Group B |
| 159 | Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor single core cable in surface/recessed PVC Conduit as required. |
| 160 | 2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 161 | 2x2.5 sq.mm + 1 x 2.5 sq.mm earth wire |
| 162 | 2x6 sq.mm + 1x6 sq.mm earth wire for A.C |
| 163 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 amps modular switch, connection etc. as required |
| 164 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required |
| 165 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). |
| 166 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, Painting etc. as required |
| 167 | Wiring for lighV power plug plug with 2 X 4 sq. mm FRLC PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FRLC PVC insulated copper conductor single core cable for loop earthing as required |
| 168 | Supplying and fi xing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required |
| 169 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excludina modular plate as reauired |
| 170 | Supplying; drawing, connecting and testing of 0.5 mm dia annealed opper conductor PVC insulated PVC sheathed telephone wire in existing onduiVwire way duct etc. as required of followin,i sizes: |
| 171 | 2 Pair (4 core) |
| 172 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making aood the same in case of recessed conduit as reauired. |
| 173 | 20mm dia PVC conduit |
| 174 | 25mm dia PVC conduit |
| 175 | Supplying and fixing of following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required. |
| 176 | 1 or 2 Module (75mmX75mm) |
| 177 | Supplying and fixing modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. |
| 178 | 5/6 amps switch |
| 179 | 3 pin 5/6 amps socket outlet |
| 180 | Telephone socket outlet |
| 181 | TV antenna socket outlet |
| 182 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/wooden block includina connections etc. as reauired. |
| 183 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioni ng etc. as required |
| 184 | Upto 450 mm sweep |
| 185 | Extra for fixing the Louvers/ shutters complete with frame for exhaust fan of all sizes. |
| 186 | Supply of LED 4ft Batten with a nominal system lumen output of 2000 lumens and a minimum system etticacy of 100 lm/W. The luminaire shall have a rated system lifetime of 25,000 burning hours at L70. The luminaire should have a color temperature of 4000K and CRl>80. The luminaire shall meet IP20 rating with THO < 10% and PF > 0.9. The luminaire housing should made of extrusion Al with a PC dittuser. The total power consumption should not exceed 21W (including driver}.l ncluding connection with 1.5 sqmm FRLS PVC insulated copper conductor. |
| 187 | Supplying of 10 Watt LED Wall Tube Lightcomplete in all respect. |
| 188 | Supplying of 300 mm 900 RPM exhaust fan complete with louver and bird guard screen with 3 core flexible wire as required. |
| 189 | Supplying of ceiling fan/bracket fans, complete with blades with suitable length of down rods shackle insulator earthing point including connection etc . as required. |
| 190 | a) 1200 mm sweep |
| 191 | Supplying and fi xing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/l solator) |
| 192 | 8 way Double door |
| 193 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required |
| 194 | 63 amps |
| 195 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB OB complete with connections, testing and commissioning etc. as required. |
| 196 | Single pole |
| 197 | Supplying and fixing single pole blanking plate in the existing MCB OB complete etc. as reauired. |
| 198 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required Details of cost for one each |
| 199 | Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick including accessories , and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but with charcoal or coke and salt) as required. |
| 200 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by ove(lapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 201 | Laying of one number PVC insulated and PVC sheathed / XLPE power40 DSR 7.3 cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushionina and orotective coverina |
| 202 | Up to 35 sq.mm. |
| 203 | Laying of one number PVC insulated and PVC sheathed I XLPE power41 DSR 7.5 cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required |
| 204 | Up to 35 sq.mm. |
| 205 | Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size on wall surface as required |
| 206 | Upto 35 sq. mm (clamped with 1mm thick saddle |
| 207 | Supply of following siz of 1.1KV grade multicore aluminium conductor XLPE insulated and PVC shethed armoured cable as per IS 7098:1988 with up to date amendment |
| 208 | 4 x 16 sq. mm |
| 209 | Supplying and making cable end terminations with brass compression44 9.1 gland and aluminium lugs for following size of PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as reauired. |
| 210 | 3½ X 25 sq. mm (28mm) |
| 211 | Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in 45 14.14 ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement: 2 fine sand) including trenching (75 cm deep) and refilling etc as required. |
| 212 | 100mm dia Please Enable Macros to View BoQ information |