|
| 1 | Stripping off worn out plaster and raking out joints of walls celings etc upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 2 | Ordinary cement concrete ( mix 1:1.5:3) with graded stone chips with (20 mm normal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes(ii) River Bazree. |
| 3 | Brick work with 1st class bricks in cement mortar (1:4) (b) In superstructure, ground floor. |
| 4 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length hooking and bending to correct shape, placing in proper position and binding with 16-gauge black annealed wire at every inter-section, complete as per drawing and direction. (a) For works in foundation, basement and upto roof of ground floor/upto 4m) (i)Tor steel/Mild steel III. Others manufacturers not specified. |
| 5 | Hire and labour charges for shuttering with centering and necessary staging upto 4.0m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs,beams and 4columns,lintels curved or straight including fitting, fixing and striking out after completion of work (upto roof of ground floor) (a) 25 mm to 30mm thick wooden shuttering as per decision and direction of the EIC. |
| 6 | Plaster (to wall ,floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course scaffolding/staging where necessary (Ground floor) (c) 10 mm thick with 1:4 cement mortar. |
| 7 | Supplying,fitting & fixing 1st quality Ceramic tiles in wall and floors to match with the existing work and 4nos of key stone(10mm)fixed with aralidiet at the back of each tile and finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includuing roughining of concrete surface if nececcary or by synthetic adhesive and grout material etc (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(b) Area of each tile above 0.09 Sq.m(ii) Other than Coloured decorative including white. |
| 8 | Supplying,fitting & fixing 1st quality Ceramic tiles in wall and floors to match with the existing work and 4nos of key stone(10mm)fixed with aralidiet at the back of each tile and finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includuing roughining of concrete surface if nececcary or by synthetic adhesive and grout material etc(B)WALL with sand cement mortar(1:3) 15mm thick and 2mm thick cement slurry at back side of tiles using [email protected]/sqm and joint filling using white cement slurry @0.20kg/sq m (b) Area of each tile above 0.09 Sq.m (ii) Other than Coloured decorative including white. |
| 9 | Synthetic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats. |
| 10 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification In Ground floor: (iii) Two coats. |
| 11 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc.fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fitttings as required , jointing materials and two coats of painting with approved paint in any position above ground( Payment will be made on the centre line measurements of total pipe line including all specials. No seprate payment will be made for accessories, specials.Payment for painting will be made seperately) (ii) 25 mm dia. medium quality. |
| 12 | Supplying, fitting and fixing clear visioned, Insulated Double Glazed two track sliding Aluminium window (U-value < 3.2W/m 2 K) made up with 6 mm thick toughened glass (wt > 15kg/m 2 ) with 12 mm air gap in between, containing perforated Al/ structural foam spacer filled with moisture absorbant dessicant at all sides duly sealed with primary sealant (polyisobutylene) and affixed inside multi cellular/ multi chember profiles of required section made of Alluminium alloy extrusions conforming to IS:733-1983 and IS:1285 - 2002 annodised/powder coated with (required film thickness and specified colour /natural) matt finished conforming to IS: 1868-2006/ IS: 13871-2002 measured as per IS:6012-1992, and sealed appropriately with secondary (polysulphide/silicon) sealant all junctions complete in all respect as per direction and satisfaction of Engineer-in-Charge including all incidental charges. (Payment shall be made on finished size of Aluminium window including frame. |
| 13 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made) ii) 40mm thick shutters with 19mm thick panel of size 30 to 45 cm (c) Other Local Wood. |
| 14 | Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts), reassembling and refitting and rehanging same with old fittings but with new screws as necessary. (Where different parts of same shutter are renewed under different item, payment under item 73 will be made once only). |
| 15 | M.S. structural works in roof trusses with tubular sections conforming to IS: 806-1968 & IS: 1161- 1998 cnnected to one another with bracket, gusset cleats as per design, direction of Engineer-in-charge complete including cutting to requisite size, fabrication with necessary metal arc welding conforming to IS: 816- 1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour reqired for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural tubular memebrs as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a height of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof. |
| 16 | Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) (i) In Roof:-b) With 0.63 mm thick sheet. |
| 17 | Galvanised iron sheet ridging fitted with necessary bolts, screws, washers etc complete.(225mm end lapping) A) 300 mm lapping each way(b) With 0.63 mm sheet. Please Enable Macros to View BoQ information |