|
| 1 | MAIN BUILDING & DORMITORY |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil 0-1.5m |
| 3 | b) 1.5-3.0m |
| 4 | Disposal of surplus excavated material for the following leads beyond the initial lead of 100 m including loading/ unloading, dressing etc complete as per specificationsa) Lead up to 500m |
| 5 | b) Lead beyond 500m but up to 1km |
| 6 | Backfilling around foundations, pipes, trenches, sumps, pits, plinths, etc. shall be carried outwith approved material in layers not exceeding 300 mm compacted thickness (higherthickness of layers upto 500mm with heavy mechanical compacting equipment) and eachlayer shall be compacted to 90% of standard proctor density for cohesive soils and to 80% ofrelative density for non-cohesive soils. |
| 7 | a) With selected excavated earth |
| 8 | b) With selected earth brought from outside including its supply and transport |
| 9 | Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. |
| 10 | ANTI TERMITE TREATMENTProviding and injecting chemical emulsion (Chlorophyriphos manufactured by Montari Ind or equivalent EC 20% with 1% concentration) for pre-construction anti termite treatment as per BIS 6313 and creating a continuous chemical barrier to a depth of 500mm from ground level and all around the column pits, surroundings of pipes and conduits and along the external perimeter of the building, top surface of plinth filling, junction of wall & floor, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surrounding of pipes and conduits etc. complete as per specification (ONLY PLINTH AREA OF THE BUILDINGS AT GROUND FLOOR SHALL BE MEASURED AND PAID FOR).With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. Note: The work must be executed by approved specialised Agency who is the member of IPCA. The Contractor shall give a 10 years guarantee as per instruction of Project Manager. |
| 11 | 300mm wide chemical barrier along external periphery of retaining wall of basement |
| 12 | PLAIN AND REINFORCED CONCRETE WORKProviding and laying plain cement concrete in all kinds of work below plinth upto all depths complete but excluding form work using 20/40 mm nominal size aggregate and coarse sanda) 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 13 | b) 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 14 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources). |
| 15 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/ Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. foundation is above plinth level)Concrete of M20 grade with minimum cement content of 270 kg /cum. |
| 16 | DESIGN MIX CONCRETE 5.33 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 17 | Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 18 | All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 19 | Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 20 | FORMWORK: Providing erecting and removing straight formwork in shuttering plywood for concrete items including forming chamfers, drip moulds, pockets etc., and including scaffolding and centring upto propping height of 5 m, finishing concrete surface after striking the formwork etc.complete (Net area of concrete formed shall be measured):Foundations, footings, bases of columns, etc. for mass concrete |
| 21 | Suspended floors, roofs, landings, balconies and access platform |
| 22 | REINFORCEMENT STEEL :Supplying, cleaning, cutting, bending, binding with 16 SWG soft annealed wire and placing in position on/at all levels and locations as per drawings, including handling and transport complete for all R.C.C works at all height:a) High yield strength deformed reinforcement bars conforming to IS: 1786 |
| 23 | DAMP PROOF COURSEProviding and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-lIl) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) |
| 24 | BRICKWORK IN FOUNDATIONBrick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement Mortar 1:6 (1 cement : 6 coarse sand). BRICK WORK IN SUPER STRUCTURE230 THICK BRICK WORK |
| 25 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) 115 THICK BRICK WORKHalf brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. |
| 26 | Cement mortar 1:4 (1 cement :4 coarse sand) |
| 27 | PLASTERING12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 28 | 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) |
| 29 | 20 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 30 | WATER PROOFINGTERRACE/ PODIUM SLAB WATER PROOFINGWMembrane aterproofingProviding and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd layer of roofing membrane APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). |
| 31 | FLOOR FINISHES AND ALLIED WORKSCement concrete flooing 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate |
| 32 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Size of Tile 1200x600 mm |
| 33 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 34 | Providing and fixing glazed screen printed border tile 75mm wide having thickness 5mm, of approved quality & make, in all shades, design and prints, in dado, over 12mm thick bed of cement mortar1:3 (1 Cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3 kg/sqm including pointing with white cement mixed with pigment of matching shade, all complete as approved by Engineer - in - Charge. |
| 35 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent |
| 36 | Kota stone slabs exposed face dressed and rubbed. 25 mm thick |
| 37 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.(i)Single socketed pipes. 75 mm diameter |
| 38 | 110 mm diameter |
| 39 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks) |
| 40 | PAINTING ,WHITE WASHING ETC.Finishing walls with water proofing cement paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 41 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats. |
| 42 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 43 | New work (two or more coats) with a base coat of white washing with lime |
| 44 | Supplying, Installation, Testing & Commissioning of followingcapacity passenger Machine room less (MRL) lift with regenerative drive as per CPWD General Specification for Electrical Works (PartIII Lift & Escalator) 2003, BIS Codes, NBC 2016 as amended upto date having provision for barrier free access as per Harmonised Guidelines & Standards for Universal Accessibility in India - 2021 of MoHUA, serving different floors in the lift shaft as per detailed specifications enclosed and as under including all other equipment and accessories complete as required:-(i) Speed-1 MPS(ii) Floors-5 (G+4)(iii) Travel -17 Meters (approx.)(iv) Stops & opening- 5 stops and 5 openings(v) Controller: A.C. variable voltage & variable frequency(vi) Automatic rescue device (ARD) complete with dry maintenance free batteries as required.vii) Operation: Microprocessor based single automatic push button/simplex selective collective/duplex collective selective with/without attendant.(viii) Power-415 Volts+10%, 3 phase, 50 Hz, 4 wires system(ix) Car Enclosure: Stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish) on all sides and stainless steel decorative ceiling with fans (indirect throw) and LED fitting.(x) The car flooring should be smooth and antiskid as approved by engineer-in-charge.(xi) Type of doors(a) Car: Power operated, centre opening horizontal sliding stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish).(b) Landing doors: stainless steel scratch proof.(xii) A hand rail not less that 600mm long at 900mm above floor level to be fixed adjacent to control panel in the lift car.(xiii) Voice announcement system in the car to announce the position of the elevator in the hoist way as the car passes or stops at floor served by the elevator.(xiv) Closed loop Control System, protection against power fluctuation, self diagnostic control, Landing doors 2 hours Fire rated, Overload detection and protection, Over speed Governor, Dot Matrix LED D & P Indicators In Car & Landings, BMS Compatibility, tamper proof infrared curtain covering almost the entire height of the lift car door, Alarm horn, Anti Nuisance Operation, CCTV camera system with 4 MP IP camera, suitable NVR and HDD for 30 days storage backup , Firemen switch, 2/3 way intercom, Emergency Stop Switch with battery backup for fan and light fitting for 1 hour, pit ladder.(xv) The lift doors shall have a vision panel to enable persons with 219 DELHI ANALYSIS OF RATES (E&M) 2025 hearing impairment to signal for help or assistance in the event of an emergency.(xvi) An appropriate technological support be provided (Through emergency messaging |services or alarms etc.) to respond to the emergency requirements of person with hearing impairment or deafness.(xvii) In case of failure of ARD or other electronic devices, a provision of manual rescue be provided |
| 45 | Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. |
| 46 | INTERLOCK PATHWAYSEarthwork in excavation in ordinary soil for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, for depth up to 1.5m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. |
| 47 | Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 3000 m as per Technical Specification Clause 301.5 |
| 48 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with Tractor Mount grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheeled roller to achieve the desired density, complete as per clause 401. |
| 49 | Providing, laying, spreading and compacting stone aggregates of specific sizes 22.4-53mm to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming, crushable screening to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification Clause 405. |
| 50 | Brick masonry work in cement mortar in foundation complete excluding pointing and plastering as per drawing and technical specifications Clauses 600, 1202 & 1203 |
| 51 | Plastering with cement mortar (1:4), 12 mm thick on brick work in substructure as per technical specification Clauses 613.4 & 1204 |
| 52 | Providing concrete for plain concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 |
| 53 | Providing and Laying of Interlocking Concrete Block Pavements having thickness 80 mm as per drawings and Technical Specification Clause 1504. |
| 54 | SEPTIC TANK WITH SOAK PIT Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.From 0.00 mt to 1.50 mt |
| 55 | 1.50mt to 3.0 mt |
| 56 | Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) and curing complete, including cost of form- work, in foundation and floors. |
| 57 | Reinforced cement concrete work in beams, suspended floors, roof having slope upto 15 degree, landings, balconies, shelves, chajjas, lintels, bands, staircases and spiral staircases etc. above plinth level up to floor V level, excluding the cost of centering, shuttering, finishing and reinforcement : in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)-Slab |
| 58 | Brick work with common burnt clay (non modular) bricks of class -150 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand). |
| 59 | Steel reinforcement for R.C.C. work ready to use \\"cut and bend\\" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500D or more. As per SI. No.- 5.22 B.1 |
| 60 | 15 mm cement plaster in single coat on rough side of single or half brick wall finished with a floating coat of neat cement. (1) 1 cement : 4 Coarse sand |
| 61 | Cement concrete flooring 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement (40 mm thick floor). |
| 62 | Supply & Laying of 40 mm gauge over burnt brick ballast including all materials, labour and T&P etc. for proper completion of the work. |
| 63 | Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:(With 20x20mm square bar) |
| 64 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved qualityCircular shape 500 mm internal diameter |
| 65 | Centering & shuttering including strutting, propping etc. and removal of form for slab |
| 66 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries equired for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.Drilling of 300mm dia bore hole manually. |
| 67 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia |
| 68 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
| 69 | DRAINAGE NETWORK Excavating trenches in all kinds of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m.Pipes 80 mm to 300 mm diameter |
| 70 | Providing and laying Non pressure NP2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand) including testing of joints etc. complete.150 mm. dia. RCC Pipes |
| 71 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design150 mm. dia. |
| 72 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of .class designation 7.5 |
| 73 | SUBMERSIBLE PUMP(A) Boring 150 dia bore hole including labuar, T & P etc. required for proper compelete of the work. |
| 74 | (B) Lowring 110 dia mm PVC pipe in bore hole including labuar, T & P etc. rquire for proper compelete ofthe work. |
| 75 | (C) Providing and fixing 110 mm dia PVC pipe 6KG/cm2 |
| 76 | (D) Shrounding and packing graded coarse sand in between bore wall & the Strainer including supply of coarse sand, labour, T&P ete required for proper compeletion of work. |
| 77 | (E) Providing and fixing G.I. pipe 32mm dia Nominal bore compelete with GI Fitting |
| 78 | (F) Submersible pump Kirlosker / Crompton or equivalent 1.0 HP I.S.I. marked. |
| 79 | (I) Single fase stater for submersible of I.S.I marked. |
| 80 | (J) 2.5 mm Sq cable for submersible moter pump. |
| 81 | (K) 4 Inch dia MS clamp made with 32*5 mm flate iron with nut & bolt |
| 82 | (L) 100 mm dia & P.V.C endcap. |
| 83 | (M) Solution for jointing P.V.C pipe. 250 gram |
| 84 | (N) 32 mm C.P.V.C pipe |
| 85 | (O) Developing of bore well by over pumping and back washing till the discharge is free from turbidity not greater then 20 p.p.m. after 20 minutes of starting of pump including hiring charges of pump set, labours, T&P complete required of completion of work. |
| 86 | (P) Nylon cloth for strainer including plastic rope, cutting holes in PVC pipe etc complete. |
| 87 | ELECTRICAL & ELV POINT WIRINGWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductorsingle core cable etc. as required.Group-C |
| 88 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as requiredGroup-C |
| 89 | Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc .asrequired. |
| 90 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required2 x 1.5 Sq.mm. + 1 x 1.5 Sq.mm earth wire |
| 91 | 4 X 1.5 sq. mm + 2 X 1.5 sq. mm earth wire |
| 92 | Wiring for light/ power plug with 2X4 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required |
| 93 | Wiring for light/ power plug with 4X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 2 Nos. 4 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required |
| 94 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). |
| 95 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 96 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 97 | Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 98 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 99 | Supply and fixing of popup boxes for perfect integration into the office furniture or on table top complete as required but not limited to, which generally includes following. 8(2X4) Module box complete (mat aluminium finish) |
| 100 | Installation kit for table top 8 (2X4) modules equipped with cable retainer for power cables, compatible with cat 6 data cabling, Audio/ video cabling. |
| 101 | SUB MAIN CABLESWiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 102 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 103 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 104 | Supply of following size of 1.1KV grade multicore aluminium / Copper conductor XLPE insulated & PVC sheathed armoured power cable as per IS: 7098 (Part-1) 1988 complete as required.3.5 core, 185 Sq.mm. Aluminium (Final Quantity as per Site Requirement) |
| 105 | 3.5 core, 70 Sq.mm. Aluminium |
| 106 | 3.5 core, 35 Sq.mm. Aluminium |
| 107 | 3 core, 10 Sq.mm. Aluminium |
| 108 | 4 core, 16 Sq.mm. Copper |
| 109 | 4 core, 10 Sq.mm. Copper |
| 110 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 111 | Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) |
| 112 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm |
| 113 | Suppling and making indoor end termination with brass compression gland and aluminium / Copper lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3.5 core, 185 Sq.mm. Aluminium |
| 114 | 3.5 core, 70 Sq.mm. Aluminium |
| 115 | 3.5 core, 35 Sq.mm. Aluminium |
| 116 | 3 core, 10 Sq.mm. Aluminium |
| 117 | 4 core, 16 Sq.mm. Copper |
| 118 | 4 core, 10 Sq.mm. Copper |
| 119 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness |
| 120 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 121 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required150 mm width X 50 mm depth X 1.6 mm thickness |
| 122 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 123 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness |
| 124 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 125 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.200 mm dia (OD-200 mm & ID-175 mm nominal) |
| 126 | MAIN DISTRIBUTION BOARDS , SUB DISTRIBUTION BOARDS & DISTRIBUTION BOARDSMAIN DISTRIBUTION BOARDS Supplying, installation, testing and commissioning of indoor floor/wall mounted modular,sectionalised, compartmentalized, extendable type MV cubicle panel with short circuit with stand capacity 31 MVA for one second, fabricated in compertmentised design from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland plates with stiffeners wherever required, having vibration free structure chemically treated with seven tank process before painting for surface treatment and powder coated, with extensible type TPN Aluminium alloy Busbars of high Conductivity DMC/SMC busbar supports, suitable for 3 phase 415 V 50 HZ AC supply i/c providing and fixing the following switchgear mounted thereon complete with gaskets and interconnections, connections as per specifications complete as required. Entire Panel shall have a common earth bar of full length at the rear with 2No earth stud. (The board shall be dust & vermin proof with degree of protection of IP 55 as per IS : 12063, free standing type, mounted on base channel of MS Section not less than 100 mm X 50 mm X 5 mm)1) All MCCBs shall be provided with microprocessor based releases, communication capable & compatible with BMS. 2) All MCCBs shall be having Ics = 100% Icu3) All MCCBs shall be provided with front rotary handle and spreader links.MDB-EXTERNAL (TOTAL OF A TO D) |
| 127 | INCOMER BREAKERS1 No. 250 Amp FP Moulded Case Circuit Breaker of 35KA (Ics=Icu upto 433 Volt) breaking capacity with microprocessor release for O/L, S/C & E/F Protection complete as required.INSTRUMENTS1 No. 0 to 500 Volt digital voltmeter 96mm x 96mm with selector switch.1 No. 0 to 250 Amp digital ammeter 96mm x 96mm with selector switch & CT's.1 Set of Phase indicating lamps with Single Pole MCB.1 Set of ON / OFF indicating lamps with Single Pole MCB.1 Set of multifuction meter with basic parameters like frequency, KW, KVA, KVAR, Power Factor, harmonics analyser etc. shall be suitable for BMS function with RS485 port for communication, MODBUS output protocol1 No. SPD -36KA (Type-B+C)BUSBARSTPN Copper busbars of minimum of 200 Amps capacity with heat shrinkable coloured sleeves and i/c DMC / SMC busbars supports at required. (Bus-Section-1) TPN Aluminium busbars of minimum of 300 Amps capacity with heat shrinkable coloured sleeves and i/c DMC / SMC busbars supports at required. (Bus-Section-2)OUTGOING2 Nos. 125 Amp TP Moulded Case Circuit Breaker of 35KA (Ics=Icu upto 433 volt) breaking capacity with Thermal Magnetic release for O/L & S/C Protection with Neutral link.2 Nos. 100 Amp TP Moulded Case Circuit Breaker of 25KA (Ics=Icu upto 433 volt) breaking capacity with Thermal Magnetic release for O/L & S/C Protection with Neutral link.9 Nos. 32 Amp DP Miniature Circuit Breaker (10KA).4 Nos. 40 Amp FP Miniature Circuit Breaker (10KA).SDB-1F (L&P) TYPICAL FOR SDB-2F (L&P) (TOTAL OF A TO D) |
| 128 | INCOMER BREAKERS1 No. 100 Amp FP Moulded Case Circuit Breaker of 25KA (Ics=Icu upto 433 Volt) breaking capacity with microprocessor release for O/L, S/C & E/F Protection complete as required.INSTRUMENTS1 No. 0 to 500 Volt digital voltmeter 96mm x 96mm with selector switch.1 No. 0 to 100 Amp digital ammeter 96mm x 96mm with selector switch & CT's.1 Set of Phase indicating lamps with Single Pole MCB.1 Set of ON / OFF indicating lamps with Single Pole MCB.1 Set of multifuction meter with basic parameters like frequency, KW, KVA, KVAR, Power Factor, harmonics analyser etc. shall be suitable for BMS function with RS485 port for communication, MODBUS output protocol1 No. SPD -36KA (Type-B+C)BUSBARSTPN Copper busbars of minimum of 200 Amps capacity with heat shrinkable coloured sleeves and i/c DMC / SMC busbars supports at required.OUTGOING12 Nos. 32 Amp DP Miniature Circuit Breaker (10KA).2 Nos. 40 Amp FP Miniature Circuit Breaker (10KA). |
| 129 | METER BOX Supply, installation, testing and commissioning of Meter Board in a 400mm x 600mm x 250mm cubicle type M.S. box made out of 2.0 mm sheet steel complete with 250Amp four pole moulded case circuit breaker (35 KA Ics Value) & Dual Source Energy meter complete with internally wired and suitable for termination of incoming cable & outgoing cables. Meter box shall be powder coated & provided with cutout in Meter Box cover for Meter reading complete as required & complying with the requirement of local supply authority meter box design. |
| 130 | DISTRIBUTION BOARDS Supplying and fixing following way, horizontal type TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with tinned copper bus bar, neutral link, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)8 way (4 + 24), Double door |
| 131 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door |
| 132 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)6 way (4 + 18), Double door - IP-54 Type |
| 133 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 Amps |
| 134 | 40 Amps |
| 135 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 Amps |
| 136 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 Amps |
| 137 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole |
| 138 | Supplying and fixing following amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole - 40Amp |
| 139 | Triple pole - 63Amp |
| 140 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 141 | RCCB BREAKER IN METAL ENCLOSURE Supply, installation, testing and commissioning of following RCCB in Metal Enclosures, Single Door, IP 65 - (Metal Enclosures Approved Make - LEGRAND / SCHNEIDER / HAGER /ABB/SIEMENS). 63A 4P RCCB Type-A- Metal Type with RCCB (300mA) |
| 142 | 40A 4P RCCB Type-A- Metal Type with RCCB (300mA) |
| 143 | MINIATURE CIRCUIT BREAKER IN SS ENCLOSURESupply, installation, testing and commissioning of Miniature Circuit Breaker in sheet steel enclosure made out of 2mm thick, suitable for 3 phase 4 wire 50 Hz AC supply complete with incoming/outgoing terminations, internal connections/ links etc as required. 32 Amp DP MCB |
| 144 | Providing and fixing following rating and breaking capacity and pole MCCB with Microprocessor release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 125 Amp (35KA) FP Moulded Case Circuit Breaker (Thermal Magnetic Release) |
| 145 | LIGHT FIXTURES & FANSSupply of wall/ceiling mounted 18-22W LED linear batten fixture (1100mm+/- 100mm length approx complete with all standard accessories for proper installation etc complete as required. Havells Cat ref. LUMILINE OR APPROVED EQUIVALENT |
| 146 | Supply of wall/ceiling mounted 9-11W LED ultraslim linear batten fixture (600mm length approx) complete with all standard accessories for proper installation etc complete as required. Havells Cat ref. LUMILINE OR APPROVED EQUIVALENT |
| 147 | Supply of surface mounted circular 14-16W LED downlighter complete with all standard accessories for proper installation etc complete as required. Havells Cat ref. INTEGRA NEO SURFACE OR APPROVED EQUIVALENT |
| 148 | Supply of 33-36W LED 600mm x 600mm recess Mounted LED fixture complete with all standard accessories for proper installation etc complete as required. Havells Cata Ref. PLUTO 2 X 2 OR APPROVED EQUIVALENT |
| 149 | Supply of wall Mounted 8-10W LED bulkhead fixture complete with all standard accessories for proper installation etc complete as required. Havells Cat Ref. ENDURA RUGBY OR APPROVED EQUIVALENT |
| 150 | Supply of 9-12W Recess Mounted circular LED downlighter complete with all standard accessories for proper installation etc complete as required. Havells cat ref. INTEGRA OR APPROVED EQUIVALENT |
| 151 | Supply of 15-18W Recess Mounted circular LED downlighter complete with all standard accessories for proper installation etc complete as required. Havells cat ref. INTEGRA OR APPROVED EQUIVALENT |
| 152 | Supply of decorative wall mounting bracket diffuser, E -27/ B-22D Lamp holder, complete with 20 watt Spiral Retrofit CFL ( complete with all accessories for proper installation as required of Havells Cat. Ref. Voila or Approved Equivalent |
| 153 | Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body.Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion)less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperaturerise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/cexternal connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required1200 mm Sweep. |
| 154 | Supply of following sizes of single phase 240 volt, 50HZ AC supply heavy duty exhaust fan complete with all accessories such as motor, blades, louvers frame, bracket, capacitor etc. including all accessories as required.300 mm dia (900 RPM) |
| 155 | Supplying and fixing Two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 156 | Providing and fixing circular/ hexagonal GI Box for Ceiling fan clamp, of internal dia 140 mm, 73 mm Height, top lid of 1.5 mm thick GI. Sheet with its top Surface hacked for proper bonding, top lid shall be Screwed into the GI Box by means of 3.3 mm dia round Headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S Bar bent to shape as per standard drawing. |
| 157 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required300 mm dia (900 RPM) |
| 158 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. |
| 159 | Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting/ LED light fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, sing core cable and earthting etc. as required. |
| 160 | WIRING & TAG BLOCKS FOR TELEPHONE & DATA SYSTEM Supplying and fixing of following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet |
| 161 | Supply, installation, testing & commissioning of following RJ-45 connectivity.Simplex Faceplate with RJ-45, information outlet with shutter compliant to TIA 568A/B with colour coding. |
| 162 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.1 or 2 Module (75 mmX75 mm) |
| 163 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair |
| 164 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, armored telephone cable in the existing surface/ recessed steel/ PVC conduit as required..20 Pair |
| 165 | Supply installation and testing and commissioning of follwing size of Telephone distribution board in a M.S. box with hinged cover/ door complete with krone type tag block with double jumpering facility mounted on a bakelite sheet etc. including terminations of cable as required. 50 Pair telephone distribution board |
| 166 | 20 Pair telephone distribution board |
| 167 | Supply, installation, testing & commissioning of wall mounting cabinets (19 inch depth) equipped with one door made of tinted glass, top and bottom cable entry plates, ventilation grills at sides, color white RAL 9002 to be supplied with earthing kit of following sizes :-6U capacity cabinet |
| 168 | Supply, installation, testing & commissioning of following Jack Panel.24 Port Jack Panel. |
| 169 | Supply, Installation, testing and commissioning of IP PBX consisting of 01 ISDN PRI Line card 10 Digital extensions 50 Analog extensions , 10 IP users License VoIP Sever Card, system should be TEC complied . Approved make- Matrix/Alcatel/Avaya/NEC |
| 170 | Supply, Installation, testing and commissioning of Analog Phone Approved make- Matrix/Beetel/Avaya/NEC |
| 171 | Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG Twisted Pair Cable in existing conduit/ on surface, Category 6Unshielded Twisted Pair, 4 pair should be complied as per UL/ETL verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in the range of 6.1mm nominal with Operating Temperature Range : -5° to +60°C, Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg etc. complete as required1 run of cable |
| 172 | 2 run of cable |
| 173 | 3 run of cable |
| 174 | Supply and fixing of following sizes of steel conduit alongwith the accessories in surface/recess including painting in case of surface conduit or cutting the wall and making good the same incase of recessed conduit as required.32mm dia |
| 175 | 25mm dia |
| 176 | 20mm dia |
| 177 | EARTHING SYSTEM:- Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 178 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. |
| 179 | Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 180 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 181 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 182 | Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. |
| 183 | Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 184 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 185 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing cable laid in pipe as required. |
| 186 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling required. |
| 187 | Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required. |
| 188 | Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 189 | SITC of Earth link -Terminal bus of 1 Nos 50 x 6 mm X 300 mm GI Stripwith 10 Nos 8mm dia holes with 8mm x 25mm dia brass nut bolt with double washer installed in insulators |
| 190 | IP CCTV SYSTEMIP CAMERASSupply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Rugged Dome Camera, 1/2.8\\" CMOS, 2 MP @ 25fps or better, triple stream, Min. Illumination required 0.01 lux @ F1.4(color), 120dB True WDR, Min. pixels : 1920 × 1080, triple stream, 2.7–12 mm motorized focus & zoom lens, BLC, HLC, 3DNR, Privacy Mask, 3 IR LEDs Smart IR with upto 50m IR distance, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 2 In/ 1out, PoE, H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, IP 67, IK 10 vandal proof, Having Operating temp range : 0°C to 60° C. Certifications: ONVIF Profile S & Profile G compliant, UL, CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant. |
| 191 | Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Bullet Camera, 1/2.8\\" CMOS, 2 MP @ 25fps or better, triple stream, Min. Illumination required 0.01 lux @ F1.4 (color), 120dB True WDR, Min. Pixels 1920 × 1080, triple stream, 2.7 – 12 mm motorized focus & zoom lens, BLC, HLC, 3DNR, Privacy Mask, 4 IR LEDs Smart IR with upto 60m IR distance, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 2 In/ 1out, PoE, H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, IP 67, IK 10 vandal proof, Having Operating temp range : 0°C to 60° C. Certifications: ONVIF Profile S & Profile G compliant, UL, CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant. |
| 192 | SYSTEM AND DATABASE MANAGERSupply, Installation, Testing & Commissioning of Central Monitoring Software to view and manage all the cameras and NVR's from a single location or PC having the following minimum specification CPU - Intel® Core™ i5 750 2.66 GHzMemory – 8GB RAMOptical Drive – DVD-RHDD – 500GBGraphics Adapter - NVIDIA® 9200 or above, 1GB independent graphic card OS - Windows® 10 Professional 64-bit / Windows 10 Ultimate 64-bit / Windows 10 Enterprise 64-bit / Windows 10 Enterprise 64-bit |
| 193 | NETWORK VIDEO RECORDER - NVRSupply, Installation, Testing & Commissioning of 24 channel NVR to view and record 18 IP cameras at Full HD(1080p Resolution) at Suitable FPS. The NVR shall have suitable HDD slots.HDD of 48 TB to be provided to enable motion based recording for 30 days |
| 194 | CCTV COLOR MONITORSupply, installation, testing & commissioning of 40\\" Flat LED Color TV's.(1no.each for NVR and 1no for PC) |
| 195 | Patch Cords. Supply, installation & testing of CAT-6 Patch Cord 1 mtr. |
| 196 | Supply, installation & testing of CAT-6 Patch Cord 2 mtr. |
| 197 | ETHERNET SWITCHESSupply, installation & testing of Layer II Managed Ethernet switch: 24 port RJ45 10 base 1000 T With 2-Fibre Ports. Ports.Suitable for CCTV Network |
| 198 | Miscellaneous Items. Connector, Jacks and connecting cables |
| 199 | Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG Twisted Pair Cable in existing conduit/ on surface, Category 6Unshielded Twisted Pair, 4 pair should be complied as per UL/ETL verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in the range of 6.1mm nominal with Operating Temperature Range : -5° to +60°C, Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg etc. complete as required1 run of cable |
| 200 | 2 run of cable |
| 201 | 3 run of cable |
| 202 | Supply and fixing of following sizes of steel conduit alongwith the accessories in surface/recess including painting in case of surface conduit or cutting the wall and making good the same incase of recessed conduit as required.32mm dia |
| 203 | 25mm dia |
| 204 | 20mm dia |
| 205 | DG SET Supply, installation, Testing & Commissioning of 'Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements Complete as per CPWD specifications, should have QR code which should contain drawing, test report OEM manual,Geo-Tag of manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings:Diesel Engine: Turbocharged Diesel engine 4 stroke water cooled, multi cylinder,dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50% RH & at 1000 Meter MSL , capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be with Electronic governor, Dry type Air filter with service indicator, first filling of engine fuel (after commissioning) lubricating Oil, Coolant and other consumables complete with all the required accessories, the Electronic governor shall be as per ISO 8528.The engine shall comply to the latest CPCB norms (CPCB IV + or better) and Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as per CPWD specificationsB: Engine mounted Instrument Panel fitted with and having digital display for following:i) Start-stop switch with key. ii) Water temperature indication.iii) Lubrication oil pressure indication.iv) Lubrication oil temperature indication.v) Battery charging indication and Voltage indicationvi) RPM indication.vii) Over speed indication.viii) Low lubricantion Oil trip indicationix) Engine Running Hours indicationix) Fuel LevelC) Alternator: Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1000 Meter MSL. The alternator shall be having Screen Protected Drip Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically balanced rotor, capable of taking 10% over loading for one hour after 12 hours of continuous operation, self cooled,self-excited and self-regulated through AVR conforming to IS13364(Part 2)/IS: 4722/BS 2613 suitable for tropical conditions and with class- H insulationD. :- Base Frame & Foundation: Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer.E) : Fuel Tank: Daily service fuel tank of 990 litres capacity fabricated out of 3 mm thick M.S. Sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class 'C' pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications.F). Exhaust System: Dry exhaust mainfold with hospital exhaust silencer and catalytic convertor.G). Starting System: 12V/24V DC starting system comprising of starter motors: voltageregulator and arrangement for initial excitation complete with suitable numbers of batteries (180 AH capacity lead acid SMF type) as required as per specifications. The battery shall be housed inside the acoustic enclosure of DG Set.Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere and the temperature rise inside the enclosure, noise level outside enclosure. The acoustic enclosure should be suitable for cable connection/connection through bus-trunking. Such arrangements on acoustic enclosure should be water proof & dust-proof conforming to IP-65 protection. The enclosure shall be as per CPCB IV + or better norms etc. and as per CPWD specifications.I). AMF Panel: Free standing floor mounted IP 42 automatic mains failure control panel including auto by-pass, suitable for KVA as below for silent type DG set complete with relays, timers, set of CTs for metering & protection and energy analyser to indicate currents, phase and line voltages, frequency, power factor, KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA (Phase & Total), KW & provision for overload, short circuit, restricted earth fault, under frequency, power (aluminum) and control (copper ) cabling of suitable size upto 15 meter between AMF panel, LT Panel and DG Set including connection interconnection etc. as required, all complete and inter locking and communication/ Ethernet /RS485/SNMP port open protocol for BMS integration including suitable software, the panel shall be of DG Set OEM make etc. as per approved by Engineering in charge and including the following:1. Suitable numbers and appropriate capacity 4 pole motorised electrically operated draw out with cradle type 3 position ACB/ MCCB with electronic release for O/C & E/F and shunt trip2. Auto/Manual/Test/Off selector switch3. Protection for under and over voltage phase reversal (2 nos Overvoltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage relay).4. 3 Sets of current transformers 15 P 10 accuracy for protection and 15 VA class-I for metering5. Energy analyser unit to indicate current, Voltage( L-N & L-L), kW, kVA (Phase & Total), Frequency, KWH, PF.6. LED Indicating lamps for load on mains and load on set7. Fuse/ MCB for instruments8. Battery charger, complete with transformer/ rectifier, D.C. voltmeter and ammeter, selector switch for trickle, off and boost and current adjustment.9. Main supply failure monitor10. Supply failure timer11. Restoration timer12. Control unit with three impulse automatic engine start/stop and failure to start lockout13. Impulse counter with locking and reset facility14. ON/OFF/Control circuit switch with indicator15. Audio/Video annunciation fori) High water temperatureii) Low lubricating oil pressureiii) Engine over speediv) Engine fails to startv) Full load/maximum load warning16. Protection for over/under Frequency, Loss of AC sensing, OverCurrent, Unbalancing load with suitable number of relays andaccessories17. Maintenance notification based on Engine Run Hour & due dateLoad Management through PLC to achieve auto opening and closing of incomer breakers, bus coupler switching of essential panel , interlocking providing signal to AMF Panel for load status and AMF shall give command to DG Set to auto start / auto stop depending upon load status and requirement etc. and necessary hardware and software required to perform the operation shall be provided by the contractor including all control wiring. |
| 206 | 125KVA |
| 207 | EXHAUST PIPING Supply and fixing Exhuast piping for DG Set's with following sizes of MS pipes conforming to IS-3589 with bends, tees, reducers, fleixble connection etc. providing & fixing suitable self supporting arrangement duly painted at suitable intervals, supplying & fixing of 75 mm thick Rock wool insulation of density 96Kg per cubic metre on all sides of Exhaust pipe with chicken mesh wrapping and 24SWG aluminium sheet cladding , suitable for outdoor installation complete as required and as per specification. 125 mm dia MS pipe (5 mm thick). |
| 208 | STRUCTURE Supply and fixing Exhuast piping for DG Set's with following sizes of MS pipes conforming to IS -3589 with bends, tees, reducers, fleixble connection etc. providing & fixing suitable self supporting arrangement duly painted at suitable intervals, supplying & fixing of 75 mm thick Rock wool insulation of density 96 Kg per cubic metre on all sides of Exhaust pipe with chicken mesh wrapping and 22 SWG aluminium sheet cladding, suitable for outdoor installation, guide support, expansion joint, SS bellows complete as required and as per specification |
| 209 | UNINTERRUPTED POWER SUPPLY (UPS) 3 KVAOnline UPS - Input supply: Single Phase, Output Supply: Single Phase.Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) ON LINE Uninterrupted Power Supply (UPS) system suitable for Single Phase input, Single Phase output AC Supply. The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual bypass, suitableisolation transformer for additional protection against neutral faults etc. The UPS systems shall be Microprocessor based Digital Control, using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter with PWM (Pulse Width Modulation) Technology. The quality of design, manufacturing and inspection process should confirm to the relevant Inter-national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >95% at 100% non-linear loads. Current total harmonic distortion(ITHD)/ total demand distortion (TDD) on the input grid shall be < 5% at 100 %load. (The required LC filters shall be included in UPS cost), extreme power factor kit to be include to limit the input pf to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ) however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC single phase 160-270V 50 Hz and delivering output AC supply true sine wave single phase 220/230/240 Volt, 50 Hz +/- 0.2Hz, Overloadcapacity of 120% for 10 mins and 150% for 1 minute. Operating temperature 0 to 40 0C, Relative humidity 0-95% non condensing, noise level lessthan 60db at 1 meter distance, Protection for Under voltage, over voltage, abnormal output voltage, battery over charging, output over current, short circuit, battery deep discharge , 10 KV surge. Display for watt/VA,Amp and Voltage power parameters etc. UPS shall comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI) type UPS (as per standard IEC 62040-1, 2 & 3) . The UPS should be with IGBT Based Inverter Technology,Communication RS232/ RS485/ SNMP port open protocol for BMS integration as per approved by Engineering in charge. Required battery racks, DC breaker of suitable rating and interconnecting copper conductor cable of suitable size andconnectors and all required accessories are inclusive in the cost. The UPS should have QR code which should contain drawing, test report OEM manual, Geo- Tag of manufacturing location etc |
| 210 | LIGHTNING PROTECTION SYSTEMProviding and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. |
| 211 | Jointing copper / G.I. tape (with another copper / G I tape, base of the finial or any other metallic object) by riveting / nut bolting / sweating and soldering etc as required. |
| 212 | Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run) |
| 213 | Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run) |
| 214 | Providing and fixing testing joint made of 20mm x 3mm thick GI strip 125mm long with 4No. G.I. bolts, nuts, chuck nuts, spring washer etc. complete as required. |
| 215 | Providing and laying G.I. Tape 32mm x 6mm from earth electrode directly in ground as required. |
| 216 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 217 | Providing, laying and fixing 80mm dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc. as required |
| 218 | AC EQUIPMENTSVRF/VRV Out Door Unit Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 ARefrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperaturewithout tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . ( 52 HP + 2#24 HP+ 2#24HP ) |
| 219 | Supplying, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 °C DB and 19 °C WB temperature. (Make will be same as of Outdoor)1.2 TR |
| 220 | Supplying, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm- (6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation) |
| 221 | 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm - (9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation) |
| 222 | 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm - (12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation) |
| 223 | 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm - (15.86 mm dia (OD) (Soft drawn) with tubethickness 1.2 mm with 19 mm thick insulation) |
| 224 | 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm - (19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation) |
| 225 | 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm - (22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation) |
| 226 | 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm - ( 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation ) |
| 227 | 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm - (28.58 mm dia (OD) (Hard drawn) with tubethickness 1.2 mm with 19 mm thick insulation) |
| 228 | Supplying, Installation, Testing and Commissioning of following minimum capacity 4 way VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 °C DB and 19 °C WB temperature. (Make will be same as of Outdoor)2.5 TR |
| 229 | Drain Piping Providing & fixing of PVC Pipe complete with fittings, supports as per specifications and duly insulated with 6/9 mm thickness of closed cell nitrile rubber as per direction of Engineer-in-charge & specifications enclosed as reqd. 40 mm dia with 9 mm thick insulation |
| 230 | 32 mm dia with 6 mm thick insulation |
| 231 | 25 mm dia with 6 mm thick insulation |
| 232 | 20 mm dia with 6 mm thick insulation |
| 233 | Propellar Fan: Of the following cfm, Supply to be rust proof body and blades,noiseless, fitted with wire guard and bird screen. Fan to be supplied as complete assembly with high efficiency continuous running motor IP54 class protection, gaurds, fittings, connecting wires and ON/OFF switches, etc and other necessity for safe installation. MAKE: CROMPTON 300 Dia |
| 234 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 235 | Supply of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make asof ODUs and IDUsIBasic Price for Y/T/Multi Joints i/c accessories,fittings,supports etc for Indoor Unit. |
| 236 | Basic Price for Y/T/Multi Joints i/c accessories,fittings,supports etc for Outdoor Unit. |
| 237 | Refrigerant Filling after installation testing. |
| 238 | SUB HEAD-1.0 SANITARY INSTALLATIONSProviding and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot restsProviding and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 239 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 240 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink of approved make as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board510x1040 mm bowl depth 250 mm |
| 241 | Providing and fixing approved make hand shower (Health faucet) of 1.2mtr long with 8mm dia Easy Flex Tube with wall hook and flow restrictor with flow rate 6 litre per minute at 3 bar in chrome finish and wall hook. |
| 242 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 243 | Providing and fixing Differecially abled toilets including Wash basin, Water closet,Cistern, grab bars & hand rails etc. The rate include cost of all material & labour involved in the item complete and all as per direction of engineer incharge.For physically handicap person consisting of;Wall Hung WC with PP soft close seat cover, HingesWall with built in Jet Concealed Cistern Cistern-01 no. Flush Plate -01 no Wall hung Wash Basin -01 no Spatula Single leverWall mounted Grab bar 600 mm long - 2 nos Wall mounted Hinged hand rail 750 x 100-01 no Bottle Trap Waste Coupling Stainless soap dish Tissue paper holderProviding & fixing heavy quality PVC waste pipe for sink including PVC waste fitting Complete Flexible Pipe 40mm Dia |
| 244 | Providing and fixing approved make, size and quality looking mirror of superior glass complete with 6 mm thick back ply/hard board ground fixed to wooden cleats on walls, allround polished 2nd class teak wood beading of size 40x20mm etc complete. |
| 245 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.Providing & fixing toilet paper holderC.P. brass |
| 246 | Providing & fixing Nickel Chromium Plated liquid soap dispenser with metallic bottle of approved brand & make 112 mm distance from wall of standard shape with bracket (Nickel chromium plating should pass Salt Spray Test for 200 hours) of the same materials with snap fittings of approved quality and colour, complete as per direction of Engineer in Charge. |
| 247 | Providing, Fixing of CP brass Towel Ring with CP brass wall brackets and providing & fixing CP brass screws complete as required. |
| 248 | Providing, Fixing of CP brass Towel Rail 600mm long without hanger with 3 hooks and CP brass screws complete as required. |
| 249 | Providing and fixing CP brass single lever low flow wall mounted Sink mixer with 15 mm CP brass single lever swivel spout with waste complete with flow rate 2.5 litre per minute at 3 bar including cutting and making good the walls where required. |
| 250 | Providing and fixing of approved make following-a) Concelaed type CP Brass diverter(for hot and cold water), overhead shower with arm with rubit cleaning system with flow rate 6 litre per minute at 3 bar complete with all accessories as required and spout with flow rate 3.8 litre per minute at 3 bar, wall flange complete with all accessories as required and making good the walls wherever required. |
| 251 | Providing,Fixing wall mounted of approved make Double Coat hook on door complete. |
| 252 | Providing and fixing CP brass 2 Way Bib cock with wall flange with flow restrictor with flow rate 2.5 litre per minute at 3 bar. |
| 253 | Providibng and fixing straight type approved make single body push fit type WC pan connector with factory supplied spring loaded seal guard of approved make with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with C.I. Pipe as supplied with the pan connector. |
| 254 | Providing, fixing, testing & commissioning of Floor drain made of PP reducing elbow (110x63 mm) with horizontal drain outlet of 63 mm OD, round top of 110 mm OD. (Floor Drain) |
| 255 | Providing, fixing and testing of PP inlet fittings with two or three saddle inlets of 40, 50 or 63 mm size, fabricated from 110 mm outer dia PP pipes and fixed to PP traps with joint complete in all respect. |
| 256 | Providing and fixing SS Grating of 125 mm dia of approved quality and colour complete as per direction of engineer in charge. Circular Type 125 mm nominal dia with 25 mm waste hole |
| 257 | Providing, Installing & fixing storage type water heater of approved make (vertical/horizontal type ) with copper container, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 8 kg/sqcm complete as required.Capacity 25 litres |
| 258 | Capacity 06 Litres |
| 259 | SUB HEAD-2.0-WATER SUPPLY Providing and fixing PE-X/A plastic pipe system, Certified complete with Red Brass / PPSU fittings with SC-Contur such as sockets, bends, elbows, tees, reducers, unions, flanges, clamps / structural steel supports,hangers, etc. necessary adapters for PB / copper to CP fittings, jointing, sundries, cutting holes in walls / floors / slabs and making good including wraping with ploythene sheet tape etc. complete for the following nominal bore(NB) (for domestic water supply inside the shafts and ceiling floor)15 mm dia |
| 260 | 20 mm dia |
| 261 | 25 mm dia |
| 262 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.15 mm nominal outer dia Pipes |
| 263 | 20 mm nominal outer dia Pipes |
| 264 | 25 mm nominal outer dia Pipes |
| 265 | 32 mm nominal outer dia Pipes |
| 266 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on Wall15 mm nominal outer dia Pipes |
| 267 | 20 mm nominal outer dia Pipes |
| 268 | 25 mm nominal outer dia Pipes |
| 269 | 32 mm nominal outer dia Pipes |
| 270 | 40 mm nominal outer dia Pipes |
| 271 | 50 mm nominal outer dia Pipes |
| 272 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External Work25 mm nominal outer dia Pipes |
| 273 | 32 mm nominal outer dia Pipes |
| 274 | 40 mm nominal outer dia Pipes |
| 275 | 50 mm nominal outer dia Pipes |
| 276 | 65 mm nominal inner dia Pipes |
| 277 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall32 mm dia nominal bore |
| 278 | 40 mm dia nominal bore |
| 279 | 50 mm dia nominal bore |
| 280 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20mm nominal bore |
| 281 | 25mm nominal bore |
| 282 | 32mm nominal bore |
| 283 | 40mm nominal bore |
| 284 | 50mm nominal bore |
| 285 | 65mm nominal bore |
| 286 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore |
| 287 | 25mm nominal bore |
| 288 | Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore |
| 289 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S (non modular) bricks of class designation 7.5 |
| 290 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S (non modular) bricks of class designation 7.5 |
| 291 | Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S (non modular) bricks of class designation 7.5 |
| 292 | Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : 25mm diameter pipe |
| 293 | 32mm diameter pipe |
| 294 | 40mm diameter pipe |
| 295 | 50 mm diameter pipe |
| 296 | 65 mm diameter pipe |
| 297 | 80 mm diameter pipe |
| 298 | 100 mm diameter pipe |
| 299 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 300 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15mm nominal bore |
| 301 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15mm nominal bore |
| 302 | Providing and fixing C.P. brass angle valve for basin mixture and geyser points of approved quality confirming to IS: 8931. |
| 303 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :50 mm dia |
| 304 | Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :100 mm dia nominal bore |
| 305 | Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and the cost of rubber gasket :100 mm dia pipes |
| 306 | 150 mm dia pipes |
| 307 | Providing and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K - 9 conforming to IS : 8329 :100 mm dia Ductile Iron Double Flanged |
| 308 | 150 mm dia Ductile Iron Double Flanged |
| 309 | Disinfecting C.I. water mains by flushing with water containing bleaching powder @ 0.5 gms per litre of water and cleaning the same with fresh water, operation to be repeated three times including getting the sample of water from the disinfected main tested in the municipal laboratory. 100 mm diameter C.I. pipe |
| 310 | 150 mm diameter C.I. pipe |
| 311 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on Wall65 mm nominal inner dia Pipes |
| 312 | 80 mm nominal inner dia Pipes |
| 313 | 100 mm nominal inner dia Pipes |
| 314 | 150 mm nominal inner dia Pipes |
| 315 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end).15mm nominal bore |
| 316 | Providing, fixing, testing & commissioning of level operated water type butterfly valve conforming to IS : 13095/BS 5155 having CI iron body , ss 316 grade dick, EPDM / nitride complete with 2 Nos. matching flanges, rubber insertion, nuts, bolts and washer etc. of following sizes with locking arrangement.Pressure Rating PN 25 :80 mm dia. |
| 317 | Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 25 rating as specified.65mm dia. |
| 318 | Providing & fixing CI `Y' Strainer (screwed/ flanged) with stainless steel fine wire mesh perforated sheet basket with necessary flange/ unions nuts, bolts and washers complete as required.65mm nominal bore |
| 319 | Providing and fixing M.S fabricated hot dipped galvanized coating puddle flange comprising of 600 mm dia long M.S class 'B' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: Underground / Overhead Tanks.)25mm dia pipe, 600mm long with size of 250x250x6 mm MS plate |
| 320 | 32mm dia pipe, 600mm long with size of 250x250x6 mm MS plate |
| 321 | 40mm dia pipe, 600mm long with size of 300x300x6 mm MS plate |
| 322 | 50mm dia pipe, 600mm long with size of 350x350x6 mm MS plate |
| 323 | 65mm dia pipe, 600mm long with size of 350x350x6 mm MS plate |
| 324 | 100mm dia pipe, 600mm long with size of 400x400x6 mm MS plate |
| 325 | Supply, installation, testing and commissioning built with Drinking Water R.O. unit with micron filtration pre-treatment unit, skid mounted R.O. module with pressure pump and pressure tank, drinking water cooler (High quality SS Tank for Storage 80 lts) , complete in all respects. |
| 326 | Providing and fixing, testing and commissioning of fully automatic \\"NO TOUCH\\" die cast aluminium, epoxy coated hand drier suitable to operate on 220 volts, single phase 50 Hz motor rating 100W, 2850 RPM automatic infrared sensing device, 1600W heating element approximate 275 cum/hr air flow wind velocity 15.5 m/sec AC power supply. |
| 327 | Providing and fixing G.I. pipes Class 'C' complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 65 mm diameter pipe |
| 328 | 80 mm diameter pipe |
| 329 | 100 mm diameter pipe |
| 330 | 150 mm diameter pipe |
| 331 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work.65 mm diameter pipe |
| 332 | 80 mm diameter pipe |
| 333 | 100 mm diameter pipe |
| 334 | 150 mm diameter pipe |
| 335 | Providing and fixing thermal insulation tubing for hot water pipes (exposed/chases/burried locations), and elastomeric flexible material having hermetic blister closed cell structure of expanded nitrile rubber having density of 60-90 Kg/m3 over pipes and it from UV protection (Black) over pipes of following nominal bores and thickness including all required accessories, protection as per manufacturer's recommendations, complete in al respect.15mm dia (6 mm thick insulation) |
| 336 | 20mm dia (6 mm thick insulation) |
| 337 | SUB HEAD : 3.0- DRAINAGEProviding, laying and joining in position HDPE DWC (Double Wall Corrugated) and conforming to I.S. 16098 of required grade SN-4/SN-8 and suitable for the respective working pressures with all fittings and specials, e.g. couplings, tees, bends, reducers, screwed adapters, flanged tail pieces, etc., jointing as per manufacturers recommendations, all complete including trenching, backfilling & pressure testing etc. (For Sewer & Storm water line). 150 mm dia (SN-4) |
| 338 | 200 mm dia (SN-4) |
| 339 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round HDPE pipes/ RCC pies/S.W. pipes including bed concrete as per standard design:150 mm diameter HDPE pipe/ RCC pipe / S. W. pipe |
| 340 | 200 mm diameter HDPE pipe/ RCC pipe / S. W. pipe |
| 341 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of HDPE pipes/ RCC pies/S.W. pipes including bed concrete as per standard design :150 mm diameter HDPE pipe/ RCC pipe / S. W. pipe |
| 342 | 200 mm diameter HDPE pipe/ RCC pipe / S. W. pipe |
| 343 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :180 x 150mm size P-type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 344 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150mm dia RCC pipe |
| 345 | MISCELLANEOUSGround Floor ReceptionProviding, supplying and placing in position reception table made of BWR plywood / MDF board with laminate finish including drawers, storage units, edge banding, hardware fittings, polishing and finishing complete as per approved design and direction of Engineer-in-Charge. |
| 346 | Providing and supplying ergonomic office / visitor chairs with cushioned seat and back, metal / wooden frame and fabric or leatherette upholstery complete in all respects. |
| 347 | Providing and fixing decorative wall back panel made of MDF / plywood with laminate / veneer finish including necessary framework, grooves, mouldings and finishing complete. |
| 348 | Providing and fixing Government emblem / building logo with individual cut letters made of stainless steel / acrylic including LED backlit arrangement, mounting system and wiring complete. |
| 349 | Providing and fixing decorative chandelier of approved make and design including suspension arrangement, wiring and LED lamps complete in all respects. Size - minimum 5ft wide |
| 350 | VIP LoungeProviding and supplying three seater sofa made of wooden frame with high density foam cushioning and premium upholstery fabric / leatherette complete. |
| 351 | Providing and supplying two seater sofa made of wooden frame with foam cushioning and upholstery fabric / leatherette complete. |
| 352 | Providing and supplying centre table made of wood / engineered wood with laminate / veneer / glass top finish complete. |
| 353 | Providing and supplying bedside table made of wood / MDF with laminate finish complete. |
| 354 | Providing and placing decorative showpieces / vases of approved design and quality complete. |
| 355 | Providing and fixing framed paintings / artworks including frame, protective glass and mounting arrangement complete. |
| 356 | Providing, supplying and installing LED television of approved make and size including mounting bracket, wiring and installation complete. |
| 357 | Providing and fixing carpet flooring of approved make, colour and pattern including underlay and fixing complete. |
| 358 | Providing and fixing decorative fancy light fixtures including LED lamps, wiring and installation complete. |
| 359 | Providing and fixing decorative chandelier of approved make and design including suspension arrangement, wiring and LED lamps complete in all respects. Size - minimum 2ft wide |
| 360 | Providing and fixing decorative wallpaper of approved design and texture including surface preparation and adhesive complete. |
| 361 | Providing and supplying decorative cushions with upholstery fabric complete. |
| 362 | Providing and supplying coat hanger / coat stand made of stainless steel / wood complete. |
| 363 | Providing and placing decorative indoor planter pots with plants complete. |
| 364 | VIP RoomProviding and supplying king size bed made of wood / engineered wood including headboard, polishing and finishing complete. |
| 365 | Providing and supplying bedside table made of wood / MDF with laminate finish complete. |
| 366 | Providing and supplying study table with chair made of wood / MDF including drawers, laminate finish and fittings complete. |
| 367 | Providing and supplying television cabinet made of wood / MDF with laminate finish including storage complete. |
| 368 | Providing and placing decorative showpieces / vases of approved design and quality complete. |
| 369 | Providing and fixing framed paintings / artworks including frame, protective glass and mounting arrangement complete. |
| 370 | Providing and fixing wardrobe made of plywood / MDF including shutters, laminate finish, shelves, hanging rods and hardware complete. |
| 371 | Providing, supplying and installing LED television of approved make and size including mounting bracket, wiring and installation complete. |
| 372 | Providing and fixing decorative fancy light fixtures including LED lamps, wiring and installation complete. |
| 373 | Providing and fixing decorative wallpaper of approved design and texture including surface preparation and adhesive complete. |
| 374 | Providing and fixing two layered curtains including sheer curtain and blackout curtain with curtain rods / tracks complete. |
| 375 | Providing and supplying mattress of approved make and size complete. |
| 376 | Providing and supplying decorative cushions with upholstery fabric complete. |
| 377 | Providing and placing decorative indoor planter pots with plants complete. |
| 378 | Providing and fixing WPC louver panel wall cladding including framework and finishing complete. |
| 379 | Caretaker RoomProviding and supplying single bed made of wood / engineered wood including headboard, polishing and finishing complete. |
| 380 | Providing, supplying and installing LED television of approved make and size including mounting bracket, wiring and installation complete. |
| 381 | Providing and supplying mattress of approved make and size complete. |
| 382 | Providing and supplying decorative cushions with upholstery fabric complete. |
| 383 | Store RoomProviding and supplying storage racks for store room made of steel / MS sections including shelves and painting complete. |
| 384 | First FloorGuest Rooms 1-6King Size Bed - Providing and supplying king size bed made of wood / engineered wood including headboard, polishing and finishing complete. |
| 385 | Providing and supplying bedside table made of wood / MDF with laminate finish complete. |
| 386 | Study Table with chair - Providing and supplying study table with chair made of wood / MDF including drawers, laminate finish and fittings complete. |
| 387 | TV Cabinet - Providing and supplying television cabinet made of wood / MDF with laminate finish including storage complete. |
| 388 | Painting - Providing and fixing framed paintings / artworks including frame, protective glass and mounting arrangement complete. |
| 389 | Wardrobe - Providing and fixing wardrobe made of plywood / MDF including shutters, laminate finish, shelves, hanging rods and hardware complete. |
| 390 | Strip Light - Providing and fixing strip lighting including LED strip, driver and aluminium profile complete. |
| 391 | TV - Providing, supplying and installing LED television of approved make and size including mounting bracket, wiring and installation complete. |
| 392 | Fancy Light - Providing and fixing decorative fancy light fixtures including LED lamps, wiring and installation complete. |
| 393 | Wallpaper - Providing and fixing decorative wallpaper of approved design and texture including surface preparation and adhesive complete. |
| 394 | Mattress - Providing and supplying mattress of approved make and size complete. |
| 395 | Cushions - Providing and supplying decorative cushions with upholstery fabric complete. |
| 396 | Two Layered Curtains - Providing and fixing two layered curtains including sheer curtain and blackout curtain with curtain rods / tracks complete. |
| 397 | Planter - Providing and placing decorative indoor planter pots with plants complete. |
| 398 | KitchenModular Kitchen Cabinets - Providing and installing modular kitchen cabinets made of BWR plywood / HDMR with laminate finish including shutters, shelves, hardware and fittings complete. |
| 399 | Dining RoomDining Table - Providing and supplying dining table made of wood / engineered wood including finishing complete. |
| 400 | Chairs - Providing and supplying dining chairs with cushioned seating complete. |
| 401 | Fancy Lights for Dining Room - Providing and fixing decorative lighting fixtures for dining area including wiring and LED lamps complete. |
| 402 | Glass Partition - Providing and fixing glass partition using toughened glass panels including aluminium / SS framing and fittings complete. |
| 403 | Wallpaper - Providing and fixing decorative wallpaper of approved design and texture including surface preparation and adhesive complete. |
| 404 | General RequirementsGlass Railing - Providing and fixing glass railing using toughened glass panels with stainless steel supports and handrail complete. |
| 405 | Main Building Logo with Letters |
| 406 | Automatic Sliding Doors - Providing and fixing automatic sliding glass doors including motorized mechanism, sensors and safety fittings complete. |
| 407 | Name Plate for all Doors - Providing and fixing name plates for doors made of acrylic / SS including mounting complete. |
| 408 | Artistic Sculpture/Planter for Courtyard - Providing and placing artistic sculpture / decorative planter for courtyard area complete. |
| 409 | SS Dustbins - Providing and supplying stainless steel dustbins of approved capacity complete. |
| 410 | Aluminium Window - Providing, supplying and fixing powder coated aluminium sliding windows of Fenesta or equivalent approved make, consisting of aluminium extruded sections with minimum 1.2–1.5 mm thick profiles, double track / triple track sliding shutters, including 5–6 mm thick toughened / float glass panels, EPDM rubber gaskets, rollers, locking system, handles, weather seals, silicon sealing, necessary fittings, accessories and installation complete in all respects as per approved design and direction of Engineer-in-Charge. |
| 411 | Door - Providing and fixing pre-engineered factory made door system consisting of solid core flush door shutter finished with laminate / veneer on both sides, complete with factory finished frame, architrave, stainless steel hinges, mortise lock, handles, door closer, stopper, rubber seals and all accessories, including fixing in position complete as per manufacturer specification and direction of Engineer-in-Charge. |
| 412 | Providing, supplying and installing decorative multi-tier ornamental fountain made of carved stone / artificial stone / FRP including circular fountain basin, fountain pedestal with multiple water tiers, water circulation pump of suitable capacity, GI/UPVC piping, nozzles, valves, filtration arrangement, waterproofing of basin, electrical wiring, LED underwater fountain lights, control panel and all necessary civil works including PCC base, plastering, finishing, testing and commissioning complete in all respects as per approved design and direction of Engineer-in-Charge. |
| 413 | Providing, supplying and fixing dormitory bed unit with integrated side table and storage, made of BWR plywood / engineered wood structure with laminate finish, consisting of single bed platform with inbuilt sliding storage compartments, one attached side table, headboard panel and integrated side reading lamp with wiring and switch, including mattress support, telescopic channels for sliding storage, edge banding, hardware fittings, polishing / finishing and installation complete in all respects as per approved design and direction of Engineer-in-Charge. |
| 414 | Mattress - Providing and supplying mattress of approved make and size complete. |
| 415 | Cushions - Providing and supplying decorative cushions with upholstery fabric complete. |
| 416 | Convention CentreVideo Wall - Supply , Installation Testing and Comissioning of Active LED with Pixel pitch 2.5mm with Die-cast cabinet size (640 x 480), Screen size: 14ft x 8ft , Resolution of screen:1790x960=1718400, LED Type: SMD2121, module resolutions (W x H) :128X64=8192 Pixels, Brightness: 600 nits or higher,color temperature:6500K (1000K～9500K Adjustable ), view angle:160°/160°, contrast ratio:5000 : 1, Frequency: 60Hz, Refresh rate: 3840 Hz, Processing depth: 14bit, video support: 2K HD, 4K UHD, life span 100000hrs, Indoor application, working temperature/ Humidity:-10℃–50℃ / 10%-90%RH (No Condensation), It should include the videwall controller with Input:- 2xHDMI 1.3, 1xHDMI 2.0, 1x3g SDI, 1xUSB 3.0, Outputs:- 6x Ethernet ouputs, 2x fiber Outputs, Audio in-out, 1x HDMI 1.3 Monitor output. The controller should be of same OEM. |
| 417 | Providing and fixing wall-to-wall carpet flooring of approved make (nylon / PP / wool blend) with printed / tufted pattern, thickness 8–12 mm, laid over prepared surface including underlay, adhesive fixing, cutting, edge binding, finishing and complete installation as per approved design and direction of Engineer-in-Charge. |
| 418 | Providing and fixing designer false ceiling made of gypsum board / calcium silicate board / stretch ceiling system on GI framework, including multi-level design, coves, grooves, cut-outs, provision for lighting fixtures, finishing with putty and paint / PVC membrane (in case of stretch ceiling), including suspension system, framing, cutting, jointing and installation complete as per approved design and direction of Engineer-in-Charge. |
| 419 | Providing and fixing decorative acoustic wall paneling consisting of GI/wooden framework, backing with mineral wool / glass wool insulation (minimum density 48 kg/m³), finished with fabric wrapped panels / perforated MDF / acoustic boards, including necessary supports, adhesive, edge finishing, fabric finish, fixing arrangement and installation complete in all respects as per approved design and direction of Engineer-in-Charge. |
| 420 | Providing and fixing decorative stage backdrop with multi-layer paneling consisting of MS / wooden framework, MDF / plywood panels, finished with laminate / fabric / veneer / paint, including grooves, mouldings, LED strip lighting provision, logo / signage area, necessary supports, wiring provision, finishing and installation complete as per approved design and direction of Engineer-in-Charge. |
| 421 | Providing and supplying round banquet table of 1800 mm diameter (6 ft) with laminated top surface, aluminium / MS frame structure, foldable self-locking legs, edge protection with aluminium / PVC beading, complete in all respects including placement as per approved design and direction of Engineer-in-Charge. |
| 422 | Providing and supplying designer Tulip chair of approved make with stainless steel / MS powder coated frame, cushioned seat and back with high density foam, upholstered in premium fabric / leatherette, including finishing, base protection and placement complete as per approved design and direction of Engineer-in-Charge. |
| 423 | Providing and supplying premium decorative sofa (couple sofa type) with solid wood / MS frame, carved or moulded antique finish, minimum 40 density foam cushioning, upholstered in premium fabric / velvet, including base protection, finishing and placement complete in all respects. |
| 424 | Providing and supplying premium foldable dustbin with stainless steel frame (SS 304, minimum 1–1.2 mm thickness) with removable inner bin, foldable stand mechanism, anti-skid base, polished / PVD finish, suitable for banquet / hospitality use, complete in all respects. |
| 425 | Providing, fabricating and fixing decorative main gate made of MS structure with laser cut / CNC design panels, including frame of MS hollow sections, infill panels, welding, grinding, finishing with PU paint / powder coating, hinges, locking system, necessary fittings and fixing complete in all respects. |
| 426 | Providing and fixing recessed LED downlights / panel lights of approved make, wattage 12W–24W, including driver, housing and installation complete (excluding wiring) as per direction of Engineer-in-Charge. |
| 427 | Providing and fixing decorative chandelier / pendant light fixture of approved design including suspension system, LED lamps and installation complete (excluding wiring). |
| 428 | Providing and fixing LED strip lighting in ceiling coves / grooves including LED strip (IP20/IP65), aluminium profile, diffuser, driver and installation complete (excluding wiring). |
| 429 | Providing and fixing wall mounted decorative lights / wall washers suitable for highlighting walls and panels, complete with driver and installation (excluding wiring). |
| 430 | Providing and fixing LED spot lights / adjustable focus lights for highlighting feature areas, including housing, driver and installation complete (excluding wiring). |
| 431 | Providing and fixing large format glazed vitrified / porcelain tiles (size 800×1600 mm / 1200×600 mm or above) of approved make, double charged / full body / PGVT finish, laid using high strength tile adhesive, including spacers, epoxy grouting, edge finishing and complete installation in all respects. |
| 432 | Providing and fixing stainless steel T-profile decorative patti of approved make and finish (natural / PVD coated), size approx. 6–10 mm width and 1200 mm length, fixed in grooves in flooring / wall / cladding using adhesive, including cutting, alignment, finishing and installation complete as per approved design and direction of Engineer-in-Charge. |
| 433 | HORTICULTUREChapter 3 – Foliage Plants (DSR 2025)Providing and stacking of Aglaonema dove variety having ht. 30 cm to 45 cm with 8 to 10 leaves well developed fresh and healthy in 25 cm size Earthen pot / Plastic pot. |
| 434 | Providing and stacking of Aglaonema Snow White hybrid plant having ht. 30 cm & above well developed fresh and healthy in 25 cm size Earthen pot / Plastic pot. |
| 435 | Providing and stacking of Areca palm having ht. 1.20 m to 1.50 m well developed fresh and healthy in 25 cm size Earthen pot / Plastic pot. |
| 436 | Providing and stacking of Areca palm having ht. 2.40 m to 2.70 m well developed fresh and healthy in 35 cm size pot. |
| 437 | Providing and stacking of Brassia variegated having ht. 30 cm to 45 cm well developed fresh and healthy in 25 cm size Earthen pot / Plastic pot. |
| 438 | Providing and stacking of Croton baby golden variety having ht. 30 cm and above well developed fresh and healthy in 20 cm size Earthen pot / Plastic pot. |
| 439 | Providing and stacking of Croton Baby Golden Punctatumaureum having ht. 23 cm to 30 cm well developed fresh and healthy in 15 cm size Earthen pot / Plastic pot. |
| 440 | Providing and stacking of Croton Golden having ht. 45 cm to 60 cm well developed fresh and healthy in 25 cm size Earthen pot / Plastic pot. |
| 441 | Providing and stacking of Croton Petra Bangalore variety having ht 45 cm and above well developed fresh and healthy in 20 cm size Earthen pot / Plastic pot. |
| 442 | Providing and stacking of Croton Petra Bangalore variety having ht 60 cm to 75 cm well developed fresh and healthy in 25 cm size Earthen pot / Plastic pot. |
| 443 | Providing and stacking of Dracaena Song of India variegated having ht 30 cm to 45 cm well developed fresh and healthy in 20 cm size pot. |
| 444 | Providing and stacking of Dracaena Kedarnath having ht 30 cm and above well developed fresh and healthy in 20 cm size pot. |
| 445 | Providing and stacking of Dracaena Mahatma having ht 30 cm to 45 cm well developed fresh and healthy in 20 cm size pot. |
| 446 | Providing and stacking of Dracaena Victoria having ht 30 cm and above well developed fresh and healthy in 25 cm size pot. |
| 447 | Providing and stacking of Ficus benjamina dwarf having ht 30 cm to 45 cm well developed fresh and healthy in 20 cm size pot. |
| 448 | Providing and stacking of Ficus benjamina having ht 45 cm to 60 cm well developed fresh and healthy in 25 cm size pot. |
| 449 | Providing and stacking of Ficus panda having ht 30 cm to 45 cm well developed fresh and healthy in 25 cm size pot. |
| 450 | Providing and stacking of Ficus religiosa dwarf having ht 30 cm to 45 cm well developed fresh and healthy in 25 cm size pot. |
| 451 | Providing and stacking of Monstera deliciosa having ht 45 cm and above well developed fresh and healthy in 25 cm size pot. |
| 452 | Providing and stacking of Monstera deliciosa having ht 60 cm and above well developed fresh and healthy in 30 cm size pot. |
| 453 | Providing and stacking of Philodendron selloum having ht 45 cm and above well developed fresh and healthy in 25 cm size pot. |
| 454 | Providing and stacking of Schefflera variegated having ht 45 cm and above well developed fresh and healthy in 25 cm size pot. |
| 455 | Providing and stacking of Yucca elephantipes having ht 60 cm and above well developed fresh and healthy in 30 cm size pot. |
| 456 | Chapter 6 – Ground Cover (DSR 2025)Providing and planting of Alternanthera (red/green) ground cover plants in prepared beds complete with good earth, manure and watering as required. |
| 457 | Providing and planting of Chlorophytum (Spider plant) ground cover plants in prepared beds complete with good earth, manure and watering as required. |
| 458 | Providing and planting of Duranta Golden ground cover plants in prepared beds complete with good earth, manure and watering as required. |
| 459 | Providing and planting of Iresine herbstii ground cover plants in prepared beds complete with good earth, manure and watering as required. |
| 460 | Providing and planting of Wedelia trilobata ground cover plants in prepared beds complete with good earth, manure and watering as required. |
| 461 | Providing and planting of Vinca sadabahar ground cover plants in prepared beds complete with good earth, manure and watering as required. |
| 462 | Providing and planting of Ophiopogon japonicus ground cover plants in prepared beds complete with good earth, manure and watering as required. |
| 463 | Providing and planting of Rhoeo discolor ground cover plants in prepared beds complete with good earth, manure and watering as required. |
| 464 | Chapter 7 – Tree Plants (DSR 2025)Providing and stacking of Albizia lebbeck height 150-165 cm. in bag size 25 cm as per direction of the officer-in-charge. |
| 465 | Providing and stacking of Alstonia scholaris height 150-165 cm. in bag size 25 cm as per direction of the officer-in-charge. |
| 466 | Providing and stacking of Azadirachta indica ( Neem ) height 120-130 cm in polybag size 25 cm as per direction of the officer-in-charge. |
| 467 | Providing and stacking of Bassia latifolia (Mahua) height 90-105 cm. in polybag size 25 cm as per direction of the officer-in-charge. |
| 468 | Providing and stacking of Bauhinia purpurea (Kachnar) height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 469 | Providing and stacking of Bombax ceiba height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 470 | Providing and stacking of Bottle palm ht. 150-180 cm bottom girth 20-25 cm well developed in poly bag size 25 cm as per direction of the officer-in-charge. |
| 471 | Providing and stacking of Cassia javanica height 120-150 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 472 | Providing and stacking of Ceiba pentandra height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 473 | Providing and stacking of Dalbergia sissoo (Seasam) height 120-135 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 474 | Providing and stacking of Erythrina indica height 150-165 cm. in polybag size 25 cm as per direction of the officer-in-charge. |
| 475 | Providing and stacking of Ficus benjamina (green) height 120-135 cm. with 6-8 branches and lush green foliage in gunny bag size 25 cm as per direction of the officer-in-charge. |
| 476 | Providing and stacking of Ficus bengalensis (variegated) height 75-90 cm., multibranched in earthen pot size 30 cm as per direction of the officer-in-charge. |
| 477 | Providing and stacking of Ficus bengalensis krishna height 75-90 cm., multibranched in earthen pot size 30 cm as per direction of the officer-in-charge. |
| 478 | Providing and stacking of Ficus elastica Decora (Rubber plant) height 45-60 cm. in earthen pot size 25 cm as per direction of the officer-in-charge. |
| 479 | Providing and stacking of Ficus infectoria (Pilkhan) height 150-165 cm. in polybag size 25 cm as per direction of the officer-in-charge. |
| 480 | Providing and stacking of Ficus lyrata height 45-60 cm. in earthen pot size 25 cm as per direction of the officer-in-charge. |
| 481 | Providing and stacking of Ficus nuda height 120-135 cm. with 6-8 branches and lush green foliage in gunny bag size 25 cm as per direction of the officer-in-charge. |
| 482 | Providing and stacking of Ficus nuda height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bag as per direction of the officer-in-charge. |
| 483 | Providing and stacking of Ficus retusa well branched height 120-135 cm. in poly bag size 30 cm as per direction of the officer-in-charge. |
| 484 | Providing and stacking of Fishtail palm ht. 150-180 cm bottom girth 15-20 cm well developed in poly bag size 25 cm as per direction of the officer-in-charge. |
| 485 | Providing and stacking of Fishtail palm ht. 210-240 cm bottom girth 25-30 cm well developed in big size HDPE bag as per direction of the officer-in-charge. |
| 486 | Providing and stacking of Foxtail palm ht. 120-150 cm bottom girth 15-20 cm well developed in poly bag size 25 cm as per direction of the officer-in-charge. |
| 487 | Providing and stacking of Lagerstroemia thorelli height 150-165 cm.in poly bag size 25 cm as per direction of the officer-in-charge. |
| 488 | Providing and stacking of Melia azedarach height 120-135 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 489 | Providing and stacking of Michelia champa (Golden Champa) height 90-105 cm. in earthen pot size 25 cm as per direction of the officer-in-charge. |
| 490 | Providing and stacking of Millingtonia hortensis height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 491 | Providing and stacking of Nauclea cadamba (Kadam) height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 492 | Providing and stacking of Peltophorum species height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 493 | Providing and stacking of Phoenix sylvestris Roxb. (Wild date palm/ khajur) height 150-165 cm. in big HDPE Bag as per direction of the officer-in-charge. |
| 494 | Providing and stacking of Phyllanthus emblica (Amla) height 150-165 cm. in big HDPE Bag as per direction of the officer-in-charge. |
| 495 | Providing and stacking of Plumeria acutifolia height 120-135 cm. with 2-3 branches in HDPE bag size 30 cm as per direction of the officer-in-charge. |
| 496 | Providing and stacking of Plumeria acutifolia height 150-165 cm. with 3-4 branches in big size HDPE bag as per direction of the officer-in-charge. |
| 497 | Providing and stacking of Plumeria alba height 120-135 cm. with 2-3 branches in bag size 30 cm as per direction of the officer-in-charge. |
| 498 | Providing and stacking of Pongamia glabra (Papri) height 120-135 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 499 | Providing and stacking of Putranjiva roxburghii height 90-105 cm. in polybag size 25 cm as per direction of the officer-in-charge. |
| 500 | Providing and stacking of Saraca indica (Sita Ashok) height 105-120 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 501 | Providing and stacking of Schleichera trijuga (Kusum) height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 502 | Providing and stacking of Spathodea campanulata height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 503 | Providing and stacking of Eugenia jambolana (Jamun) height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge. |
| 504 | Providing and stacking of Terminalia arjuna height 150-165 cm. in polybag size 25 cm as per direction of the officer-in-charge. |
| 505 | Providing and stacking of Washingtonia filifera palm stem ht. 120-135 cm with 8-10 healthy lush green leaves well developed in big size HDPE bag as per direction of the officer-in-charge. |
| 506 | Providing and stacking of Conocarpus erectus of ht. 240-270 cm, healthy, well developed in big Poly/Gunny Bag as per direction of the officer-in-charge. |
| 507 | Providing and stacking of Ficus krishna of ht. 120-135 cm, healthy, well developed in big Poly/Gunny Bag as per direction of the officer-in-charge. |
| 508 | Providing and stacking of Salix babylonica of ht. 150-165 cm, healthy, well developed in big Poly/Gunny Bag as per direction of the officer-in-charge. |
| 509 | Providing and stacking of Terminalia mentaly of ht. 180-210 cm, healthy, well developed in big Poly/Gunny Bag as per direction of the officer-in-charge. |
| 510 | Chapter 8 – Hedges & Edging (DSR 2025)Providing and planting of Bougainvillea hedge plants including preparation of bed, manure, watering and maintenance as directed by the officer-in-charge. |
| 511 | Chapter 9 – Lawns & Miscellaneous (DSR 2025)Preparation of ground for lawn including dressing, digging, removing weeds, stones and rubbish and fine levelling complete as per direction of the officer-in-charge. |
| 512 | Supplying and stacking of good earth for lawns including royalty and carriage complete as per direction of the officer-in-charge. |
| 513 | Providing and laying of doob grass turf with earth including watering and maintenance complete as per direction of the officer-in-charge. |
| 514 | Providing and spreading of farm yard manure or sludge manure in lawn areas complete as per direction of the officer-in-charge. |
| 515 | Providing and spreading of chemical fertilizer in lawn areas complete as per direction of the officer-in-charge. |
| 516 | Maintenance of lawn including watering, mowing, trimming and dressing complete as per direction of the officer-in-charge. Please Enable Macros to View BoQ information |