|
| 1 | Earth work in cutting or in embankment in ordinary soil, excavation to be in the form of regular pits not not exceding 0.50 mt. in depth and work in embankmet to be n 20 cm. layers includding ramming and dressing the surface to required level and slope and also including 1.5 mt. lift and 30 mt. lead as per SL. No.253 detailed specification & direction of E/I. for Embankment work. |
| 2 | Construction of subgrade and Earthern shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. |
| 3 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. |
| 4 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405. |
| 5 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. |
| 6 | Brick edging on both side of road with S.O.B. Brick 8 cm wide and 12 cm deep laid with mud mortor all labour finished to the required template and in proper alignment and also including dressing and ramming the excavated earth including all labour T&P sundries required for proper completion of the work. SI No. 765 |
| 7 | Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 |
| 8 | Providing and applying tack coat with RS-1 using distributor at the rate of 0.275 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. |
| 9 | Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. |
| 10 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 |
| 11 | Construction of subgrade and Earthern shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. |
| 12 | Construction of un-reinforced dowel joints at expansion and construction joint only, plain cement concrete pavement,thickness as per design,over a peroared sub base with 43 grade cement or any other type as per clause 1501.2.2 M 30 (Grade) coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25mm,mixed in a concrete mixer of not less than 0.20 cum capacity and approprite weight batcher using approved mix design,laid in approved fixed side formwork ( steel channel,laying and fixing of 1.25 micron thick polythene film, wedges steel plates including leveling the formwork as per drawing) spreading the concrete with shovels rakes compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer sealant,dowel,near approaches to bridge/culvert and construction joints, curring compound (where specified) and water finishing to lines and grade as per drawing and technical specification 1501 |
| 13 | S/F Inaugration black granite (Polished) 20mm thick stone size 0.90x0.75 m including lettering, printing, border etc. will be painted of superior quality is required shade and colour including fixing excavation of foundation (1.40x0.50x0.40 m), P.C.C. 1:6:12 (1.40x0.50x0.15m), brick work 1:3 cement coarse sand foundation(1.40x0.345 x0.30m) , upto (1.40x0.23x1.35m),12mm thick plaster 1:3 cement coarse sand and finishing walls with water proffing white cement paint of approved make and quality such as super snowcem paint etc. all complete. |
| 14 | Side Drain 0.30m wide and 0.30m deep |
| 15 | supply Of 350 mm dia NP3 Hume pipe Please Enable Macros to View BoQ information |