|
| 1 | Full stator copper rewinding of ceiling fan (condenser type) of 1200 mm sweep including cleaning and insulating the stator slots, sleeving, soldering, wrapping of cotton tape, reassembling, varnishing and testing etc. complete. |
| 2 | Full stator copper rewinding of air circulatory fan (condenser type) of 600 mm sweep including cleaning and insulating the stator slots, sleeving, soldering, wrapping of cotton tape, reassembling, varnishing and testing etc. complete. |
| 3 | Full stator copper rewinding of air circulatory fan (condenser type) of 450 mm sweep including cleaning and insulating the stator slots, sleeving, soldering, wrapping of cotton tape, reassembling, varnishing and testing etc. complete. |
| 4 | Full stator copper rewinding of ceiling fan (condenser type) of 1400 mm sweep including cleaning and insulating the stator slots, sleeving, soldering, wrapping of cotton tape, reassembling, varnishing and testing etc. complete. |
| 5 | Full stator copper rewinding of an Exhaust fan (condenser type) of following rating 900/1400 RPM including cleaning and insulating the stator slots, sleeving soldering wrapping of cotton tape, varnishing re-assembling and testing etc. complete. |
| 6 | 12\\" Sweep |
| 7 | 15\\" Sweep |
| 8 | 18\\" Sweep |
| 9 | Replacement of ball bearing of ceiling fan including greasing, re-assembling and testing etc. |
| 10 | Fabrication of shaft after removing the shaft from the stator body safely and then labour works for welding and turning of the same to give the original shape from workshop and other petty material required. to complete the job to the entire satisfaction of Engineer-in-charge. |
| 11 | Supply and erection of rubber reel after dismantling the defective real including connection and testing etc. |
| 12 | Providing split pin, check nuts, hanger nuts and bolts etc. including hanger if required to be replaced after removing the old. The rates includes of ceiling fan re-reaction after repair and other petty material such a screws pin, bolts nuts etc. as per requirement at site. |
| 13 | Repair / Replacement of BLDC PCP for 48\\"/56\\" Ceiling Fan, re-assembling and testing etc. to complete the job to the entire satisfaction of Engineer-in-charge. |
| 14 | Supply and erection of fan condenser (paper condenser) for ceiling fan of following rating. The condenser is to be installed in existing ceiling fan after dismantling the defective condenser including connection and testing etc. |
| 15 | Condenser 3.15 µ fd. |
| 16 | Condenser 2.15 µ fd. |
| 17 | Condenser 4 µ fd. |
| 18 | Supply and Erection of 1200/ 1400 mm ceiling fan’s/ 12”/15”/18” Exhaust Fan aluminium blades set of matching colour of existing ceiling fan/ exhaust fan make. The job includes the cost of fixing of new blade set after dismantling the existing defective blade. The ceiling fan/ exhaust fan blades should be of same make of the existing ceiling fan/ exhaust fan make only. (Blades 3 Nos. in one set). |
| 19 | Spray/ painting of steel shutter and other out door type pedestal etc. The steel shutter/ rusted outer cover of switchgear etc. in pedestal shall be given anti-rust/ grease treatment and then spray painted with one coat of primer & two coats of superior quality of grey paint as approved by the Engineer-in-Charge. |
| 20 | Painting of junction box and outer side cover with superior quality of red paint removing existing rusted paint/ rust etc. properly. The cement collar shall be repaired first with cement/ sand plastering compound etc. with water up to two days painted with 2 coats of white snowcem of superior quality to make even surface and finished properly. Please Enable Macros to View BoQ information |