|
| 1 | Demolition of cement concrete ( unreinforced) in ground floors and pavings n exc 15 cm thickness below or above ground level complete all as specified and as directed. |
| 2 | M&L for cement concrete 100mm thick type C2 1:3:6 in sub base using 40mm graded aggregates complete all as specified and directed |
| 3 | M&L for cement concrete 40mm thick type B1 1:2:4 at top surface using 20mm graded aggregates, complete all as specified and directed |
| 4 | Demolition of Reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 5 | M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 6 | M&L for RCC (nominal mix) type B1, 1:2:4 (20 mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed |
| 7 | Material and labour for Plain Cement concrete 1:4:8 type D2 using 40mm aggregate as in foundations,filling and mass concrete complete all as specified and as directed. |
| 8 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in 1:4 cm, complete all as specified and as directed. |
| 9 | Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) |
| 10 | Taking down cement plaster on brick or concrete surface including racking out joints, hacking for key scrubbing down water etc and removing materials from site of work complete all as directed. |
| 11 | Taking down chowkats or frame with shutters (without taking off shutters from the frames ) n exc. 1.5 sqm each all as specified and directed. |
| 12 | M&L Powder coated aluminium sliding window shutters, aluminium section including necessary joining cleats, glazing clips, Aluminium grill (decogrill Design no 20) and F/h type frame, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 No.) or hinges type B-21 100 mm long (2 nos.), suitable handle or Star lock, (1 no.) gasket,Aluminium wire cloth 0.45mm dia of f wire and average width of aperture 1.40mm incl necessary channel frame work and 5mm thick float glass including fixing arrangement and clips complete all as specified and as shown on drawing NOTE : (i) Rates include all glass glazing/SS wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, etc (iii).comprising frames of section No : 20831 three track top, 20832 three track bottom, 20736 top and bottom shutter, 20738 inter lock, incl \\"C\\" channel and \\"L\\" angle, roller bearing, rubber beading, consealed lock,including solar control film 25 micron thick, reflective type, sticked to glass panes as per manufacturer’s instruction, complete all as specified and directed. |
| 13 | S&F for 5.50 mm thick sheet glass ordinary quality and glazing with oil putty/ wooden beading in square exc 0.5 Sqm in each pane including solar control film 25 micron thick, reflective type, sticked to glass panes as per manufacturer’s instruction (For Door) , complete all as specified and directed.Make : MODI/ SAINT GOBAIN/ ATUL/ TRIVENI |
| 14 | S&F framed work such as grills, gratings etc with end of bars, shouldered and/ or rivated, or forged into spikes; framed guard bars, framed work for door and windows, railing and similar work confirming to Fe 290 Gde-E-165, Complete all as specified and as directed. |
| 15 | Taking down chowkats or frame with shutters (without taking off shutters from the frames ) exc. 1.5 sqm each all as specified and directed. |
| 16 | S&F Anodised Aluminium frame work in partition/doors/windows with shutter all round and including aluminium beading,glazing cleats,neoprene rubber beading fixed in frames Make of aluminium section – JINDAL/ INDAL/ HINDALCO |
| 17 | M & L fixed in repair 12 mm thick particle board for insulation purposes, fixed with nails/ screws to aluminium framework all as specified and directed |
| 18 | S&F Alumunum powder coated, barrel tower bolt 200mm long complete all as specified and directed. |
| 19 | S&F in repairs mortice lock, brass, 4 levers type, size 100mm complete all as specified and as directed. |
| 20 | S&F in repair floor door stopper of aluminum alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor but of brass body and tongue with hard drawn steel spring (Overall length of cover plate 140mm) fixed in repairs etc complete all as specified and directed. |
| 21 | Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing |
| 22 | M & L for brick work with sub class 'B' old size bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as directed. |
| 23 | M&L for 15mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm and 5mm thick) mixed with water proofing compound in top layer @2% by the weight of cement or as per manufacturer's instructions finishing the surface even and smooth without using extra cement complete all as specified and as directed.Note : Integral water proofing compund shall be measured and paid separtely. |
| 24 | Supply only integral water proofing compound complete all as specified and as directed. |
| 25 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. ( Note :- Shade shall be approved by Engr-in-Charge) |
| 26 | M & L for 10 mm thick rendering in CM (1:6) finished even and smooth without using extra cement to wall complete all as directed. |
| 27 | M&L for preparing of new surfaces of walls and applying two coats of oil emulsion distemper on the same after Chalk whiting, on plastered surfaces, prepara-tory to distempering on internal wall surfaces , all complete as specified and directed. |
| 28 | M&L for preparing of old surfaces of walls and applying one coat of oil emulsion distemper on the same, all complete as specified and directed. |
| 29 | Dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings. |
| 30 | S&F pre- painted galvalume aluminum zinc coating GI Based corrugated steel sheeting 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, chajjas, fixed with self tapping screws complete all as specified & directed |
| 31 | S&F pre- painted galvalume aluminum zinc coating GI Based plain corrugated steel sheeting 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, chajjas, fixed with self tapping screws complete all as specified & directed |
| 32 | Dismantling boarding, any description, fixed in any position with screws as specified and directed. |
| 33 | M&L for 2nd class hardwood weather boarding, clean sawn, thickness 20 mm to 25 mm and rebated on thick edge to give 20mm laps and fixed all as specified and directed. |
| 34 | S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm and n exc 10cm, (dia of neck 11 to 15mm) all as specified and directed. |
| 35 | M&L for two coats of synthetic enamel paint over a coat of pink primer of new wooden surface of any description, not other wise described over 10 cm width or girth incl. preparation of surfaces. |
| 36 | Taking down roof trusses, coupled rafters or trussed beams of clear span upto 4 mtrs, complete all as specified and directed. |
| 37 | S&F in repair Roof trusses (framed), Fe- 290 (Gde E- 165) quality-A trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed. |
| 38 | M&L for two coats of synthetic enamel paint over a coat of red oxide zinc chrome of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described all as specified and directed. |
| 39 | M&L for painting on old Surfaces of any description including preparartion, over 10cm in width or girth,not otherwise described complete as specified and directed. |
| 40 | M&L for PCC type B1 using 20mm graded crushed stone agg as in benching, coping for drain, etc including necessary form work, complete all as specified and directed. |
| 41 | M&L for plain cement concrete (1:3:6) type C2 using 40mm graded crushed stone aggregate as in surface channel/drain, complerte all as specified and directed. |
| 42 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms moulds, mitred/stopped ends etc complete all as specified and directed. |
| 43 | M&L for 15mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement, complete all as complete all as specified and directed. |
| 44 | Taking down carefully/ aluminium point wiring (light, fan, socket or power) comp incl.(fitting such as switches, ceiling rose, pendants, regulators, socket, boards, DB, MCB, light fitting etc), removing materials to store for keeping in safe custody and making good disturbed surfaces of walls, floors etc, comp all as per specified and directed. |
| 45 | M&L for point wiring for one light point/ fan /bell point surface type controlled by one way switch with 1.5 sqmm PVC insulated unsheathed single core multi stranded copper conductor (FRLS) cable 1100 V grade in and including PVC capping and casing (double lock, ISI marked) of suitable size with all necessary fittings along with 1.5 sqmm continuous PVC insulated unsheathed stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including PVC rectangular switch board with plastic laminated sheet cover for mounting switches, socket, fan regulators etc including testing on completion after taking down the unsv one comp all as specified and as directed. |
| 46 | All as per item no 45 here-in-before but for one 5 pin 6/5 Amp socket outlet controlled by one switch on independent board all as specified and directed. |
| 47 | All as per item no 46 here-in-before but for one 5 pin socket outlet, 15 Amp independent with 4 sqmm single core multi stranded copper conductor (FRLS) cable along with 4 sqmm continuous PVC insulated unsheathed stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed. |
| 48 | Taking down sub main wiring of any size comp all as specified and directed. |
| 49 | M&L for sub main wiring with 2 run of single core 4.0 sqmm FRLS (ISI marked) PVC insulated unsheathed multistranded copper conductor cable drawn through and including PVCconduit concealed type of min size 25 mm along accessories on roof/ wall/ ceiling etc including one run of 4.0 sqmm FRLS (ISI marked) PVC insulated unsheathed multistranded copper conductor as earth wire, including taking down old one comp all as specified and directed. |
| 50 | Supply and fix switch piano flush button single pole, one way 5 amp, after taking down unsv one comp all as specified and directed. |
| 51 | Supply and fix socket outlet 5 pin, 5 Amp flush type after taking down old unsv one comp all as specified and directed. |
| 52 | Supply and fix switch socket combination 2 in 1, 5 pin , 5 Amps and 15 Amps (ISI marked) flush type , universal shutered, after taking down unsv one comp all as specified and directed. Make : |
| 53 | Supply and fix ceiling rose, surface bakelite, 65mmX50mm, two to three terminal , PVC/Polycarbonate, insulated body (ISI marked) after teking down unsv one comp all as specified and directed. |
| 54 | Supply and fix LED tube light fitting 1X20 Watts 220 V,AC basic all purpose surface and wall mounted decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose ,after taking down unsv one comp all as specified and as directed. |
| 55 | Supply and fixing LED flood light 70/80 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as per specified and directed. |
| 56 | Supply and fix LED adjustable light fitting with high diffuser 1X20 Watts 220 V,AC basic all purpose surface and wall mounted with driver, holder including adjustable light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose one comp all as specified and as directed. |
| 57 | Supply and fix wall mounted fan with 400 sweep dia, comp with three blade, 230V, and connection to ceiling rose comp all as specified and as directed. |
| 58 | Supply and fix sheet metal enclosure MCB Db 4 way SPN double door suitable for 240 V fixed flused on walls including cutting knitch and making good disturbed surface incl blanking plates as per requirment incl taking down unsv one comp all as specified and directed. |
| 59 | Supply & fix MCB, SPN, AC, 240V IP-43 of 16 to 32 Amps capacity \\"C\\" series and making connections incl taking down unsv one comp all as specified& directed. |
| 60 | Supply & fix MCB, SP, AC, 240V IP-43 of 05 to 32 Amps capacity \\"C\\" series, 10KA breaking capacity and making connections incl taking down unsv one comp all as specified& directed. |
| 61 | S&F test point terminal box made of gun metal or phosphorus bronze 75X75X25mm drilled and screwed including 3 Nos 8 mm hexagonal head screw comp all as specified and directed. |
| 62 | M&L for earthing complete with galvanized steel earth plate electrode 600X600X6 mm, burried directly and preferably vertically in ground (earth pit not less than 2,25 mtr deep below ground level) with top edge of plate not less than 1.5m below ground level connected to galvanized earth wire 4mm by means of bolt, nut and washer of GI or steel earthing lead to be procted by GI pipe of 40mm bore light grade and other end connected to earthing test point or main controlled switch as directed including providing funnel with 20 mm bore GI pipe medium grade for watering wire mess, charcoal oe coke and common salt in alternative layer of 15 cm (compacted thickness) all around the earth electrode , concrete earth pit in PCC (1:3:6) type CI, 50 mm thick precast RCC (1:2:4) type B1 cover slab reinforced with 8mm dia TMT bar @ 15 cm both ways and suitable handle made out of 10mm dia, including necessary excavation and earth work , returning filling and disposal of surplus soil to a distance n. exc 50m and testing on comp connection all as shown in electric plate no 3 SSR part-1 and as directed. Please Enable Macros to View BoQ information |