|
| 1 | Construction of OHT:Design, Submission of vetted design from IIT/NIT, drawing and Supply of all materials, labour, T&P etc. required for construction of INTZ type RCC Overhead Tank with minimum freeboard of 15 cm including Ventilator and Water Level Indicator, Lightning Conductor, C.I. D/F Vertical Pipes (Inlet Pipe (2 Nos.), Outlet Pipe (2 Nos.), Overflow Pipe & Washout Pipe)(separate column pipes for the inlet for each rising main and a separate outlet for each DMA), Duck Foot Bend, Puddle Collars and Bell Mouths, DI/D/F Sluice Valves on Inlet, Outlet & Washout Pipes and Sluice Valve Chambers, Bypass Arrangement of OHT, Flooring with Apron & Drain (minimum 100 mm thick PCC of 1:2:4 & 100 mm thick RCC of 1:1.5:3 with nominal reinforcement), the construction of a 30x30 cm cement concrete (CC) drain with an internal wall thickness of 100 mm, over a 60 cm wide plain cement concrete (PCC) base of 100 mm thickness in 1:2:4 mix, for rain water disposal of campus, shall be carried out for a minimum length of 100 meters along the boundary wall of the campus up to the disposal point, Floor Level shall be 60 cm above the Finished Ground Level of Campus including supply of earth to fill the whole campus according to the formation level(floor) of OHT, Three Coats of Apex Painting over One Coat Primer of Approved Colour after Finishing of RCC Surface with Grinder, Repair of Pinholes, Unevenness, supply and fixing of two number 60 Watt solar light system (with dry battery) at the height of second brace of the OHT near stair case and main gate, Railings – G.I. Pipe Railing around Staircase (both sides), Balcony & Top Dome Periphery, S.S. Ladder from Opening of Top Dome to Bottom Dome, Staircase (Separate Two-Column Based RCC Staircase including Escape Channel of 20 m Length, Box-Type Enclosure at the Entrance of the Staircase having Locking Arrangements, and 1.20 m Wide Balcony), Food Grade Epoxy Coating of FOSROC / Ciba-Geigy on Inside Surface Area of Water Container after Successful Testing for Water Tightness of Following Capacity and Staging mentioned as per BOQ.For bidding purposes, the bearing capacity of soil shall be considered as 8 t/sq.m. Working design shall be based on the SBC determined (The depth of the bore hole shall be two times of proposed diameter raft foundation of OHT) after soil investigation / 8 tonne/sq.m. The depth of foundation is a minimum 2.50 m from the existing ground level on raft foundation or pile-cum-raft foundation or at a greater depth based on the design of the tank, for which no extra claim shall be entertained.Note: The bid price of Overhead Tanks is to be submitted considering net safe allowable bearing capacity as 8 t/m², keeping the minimum foundation depth to be 2.5 m below the existing ground level at the site of work. The successful bidder will be required to investigate the soil bearing capacity. If net safe allowable bearing capacity is found to be equivalent to or more than 8 t/m², the design of OHT will be based on 8 t/m² capacity. However, in case the net safe allowable bearing capacity is found to be below 8 t/m², then the design of OHT will be based on the actual bearing capacity, adopting raft foundation or raft-cum-pile foundation. |
| 2 | For Zone 6 -Capacity - 600 KL Staging -22 m a. C.I D/f pipe inlet - 2nos of 300 mm diab. C.I D/f pipe outlet - 2nos of 400mm diac. C.I D/f pipe overflow - 2nos of 400mm diad. C.I D/f pipe washout - 1nos of 200mm dia |
| 3 | For Zone -7Capacity - 1225 KL Staging -22m a. C.I D/f pipe inlet - 2nos of 300 mm diab. C.I D/f pipe outlet - 2nos of 400mm diac. C.I D/f pipe overflow - 2nos of 400mm diad. C.I D/f pipe washout - 1nos of 200mm dia |
| 4 | For Zone 9 -Capacity - 525 KL Staging -22m a. C.I D/f pipe inlet - 2nos of 300 mm diab. C.I D/f pipe outlet - 2nos of 400mm diac. C.I D/f pipe overflow - 2nos of 400mm diad. C.I D/f pipe washout - 1nos of 200mm dia |
| 5 | Construction of CWR:Supply of all materials, labour T&P and construction of a R.C.C. CWR of various sizes including free board, as per approved design and drawing ,including fixing of inlet and outlet pipes of suitable sizes, fixing of M.S. ladder inside and outside the tank, M.H. covers with locking arrangement and ventilators at top and suction level indicator, etc as per IS specification, including necessary excavation to achieve proper level of bed as per drawing and design and refilling of earth around CWR as per direction of Engineer-Incharge and also development and site clearence as per requirement and supply of all material, labour T&P etc., & construct drainage arrangement for empty CWR for cleaning, repairs and maintenance etc all complete. |
| 6 | For Zone 7Capacity- 425 KL |
| 7 | Construction of Pump Houses |
| 8 | Provide all materials, labour, T&P etc. complete for construction of Pump House size 3.6 x 3.0 x 3.0 m, Chlorinating Room size 1.8 x 2.5 x 3.0 m as per type design and specifications provided in the tender document including two coats of Apex Ultima exterior paint over one coat of primer. The structure will be RCC frame structure providing separate beams at plinth and lintel level. The reinforcement of RCC base slab of the by-pass chamber will be connected with the plinth beam to ensure its stability.The floor of the Pump House shall be constructed by providing 300 mm sand filling over compacted earth and thereafter 100 mm thick 1:2:4 PCC and 100 mm thick RCC with minimum reinforcement. The V-notch of 6 mm thick MS plate shall be fixed in RCC top beam of 230 mm thickness. The apron shall be constructed with a protection brick wall of 230 mm width & 600 mm thickness, including 100 mm thick RCC with minimum reinforcement over PCC.The top roof slab shall be treated with brick coba using appropriate waterproofing chemicals. The vertical rainwater pipes shall be fixed using minimum 100 mm dia PVC pipes of 8 kg/cm². All works shall be completed to the satisfaction of the Engineer-in-Charge |
| 9 | Provide all materials, labour, T&P etc. complete and construct Pump house size (3.6x3.0x3.0x3.0)m Chlorinating room size (1.80x2.50x3.0)m as per departmental type design for Tube Well. |
| 10 | Provide all materials, labour, T&P etc. complete and construct Pump house size (3.6x4.0x.5.5)m Chlorinating room size (1.80x2.50x3.0)m as per departmental type design for CWR. |
| 11 | RENOVATION OF EXISTING STRUCTURE (OHT, BOUNDARY WALL) |
| 12 | Scaffolding:Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven-storey height, made with 40 mm dia M.S. tubes at 1.5 m centre to centre, horizontal & vertical tubes joined with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps, and M.S. staircase system in the scaffolding for working platform etc., and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter.The scaffolding system shall be stiffened with bracings, runners, connections with the building etc., wherever required for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of the Engineer-in-Charge. The elevational area of the scaffolding shall be measured for payment purposes. The payment will be made once, irrespective of the duration of scaffolding.(Payment 10% of the total amount of OHT/Boundary renovation items)Note: This item is to be used for maintenance work judicially; necessary deduction for scaffolding in the existing item is to be done |
| 13 | Surface Preparation:Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual chisel and/or by standard power-driven percussion type tools of approved make, including tapering of all edges, making square shoulders of cavities, including cleaning the exposed concrete surface and reinforcement with wire brushes etc., and disposal of debris for all leads and lifts, all complete by using alkaline chemical rust remover of approved make applied with paint brush, and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-in-Charge. (Payment 10% of the total amount of OHT/Boundary renovation items) |
| 14 | Injection Grouting in Vertical Surface/Wall:Placing and fixing nozzles by drilling machine in tank wall having minimum diameter of nozzle 15 mm, and provided at regular intervals not exceeding 1.0 m (the center-to-center distance of nozzles shall not be more than 1.0 m), including construction joints. Injection of Pidicrete AM (polymer-based, high-strength, shrinkage-compensated grout) admixed with cement through nozzles under pressure by sump at the rate of 250 grams per bag of cement. Sealing the nozzles after grouting with polymer product mixed with cement(Payment 10% of the total amount of OHT/Boundary renovation items) |
| 15 | Repairing of Spalled and Loose Concrete:Where reinforcement is exposed, apply Fixit Rust Remover by means of brush to the reinforcement for cleaning bars and steel surface. Then apply a bonding coat of acrylic-based polymer with cement slurry in 1:1 ratio to the pre-wetted concrete by brush.Now apply the mixture of 1:1 cement and coarse sand to the prepared substrate when the primer becomes tacky. The repair shall be done using 50 mm thick M25 grade concrete.(Taking 20% of the total surface area of OHT)(Payment 15% of the total amount of OHT/Boundary renovation items) |
| 16 | Dismantling of all existing sluice valves of Inlet/Outlet/Washout and sluice valve chambers and replace all the valves with DI sluice valves including reconstruction of sluice valve chambers, repairing/replacement of vertical pipes/rubber packings, grouting of vertical pipes at cone wall of the OHT, replacement of existing M.S. ladder with S.S. ladder (The size of SS 304 rectangular tube shall be 50x100 mm with a minimum 3.0 mm wall thickness) inside the tank, replacement of M.H. cover with fixing of frame on the top dome, replacement of mosquito jali with a new one complete. Supply and fixing of 20 mm dia G.I. pipe railing around staircase (both sides), balcony & top dome periphery. Supply and installation of additional inlet/outlets column pipes if needed, as per revised design as seperate inlet and outlet column pipes should be provided for RM and DMAs respectively (Payment 15% of the total amount of OHT/Boundary renovation items).Supply and fixing of water level indicator, lightning conductor on the top dome and making earthing with required earthing wire from top to bottom of the tank, 100 mm thick 1:4:8 plain cement concrete and 100 mm thick RCC of M15 grade flooring with apron with 3 mm floating coat of neat cement, including protection brick wall (230x600 mm in 1:4 cement mortar including 12 mm thick plaster on the outer surface) on the outer edge of the floor shall be constructed. The fabricating/repairing of escape channel of 20 m length, box-type enclosure at the entrance of the staircase having locking arrangements, food grade epoxy coating of FOSROC / Ciba-Geigy on the inside surface area of the water container after successful testing for water tightness and three coats of Apex painting (Asian Apex Ultima exterior paint) over one coat primer of approved colour after finishing of RCC surface with grinder, repair of pinholes, unevenness, as per the direction of the Engineer-in-Charge.(Payment 10% of the total amount of OHT/Boundary renovation items) |
| 17 | Dismantling of damaged part of plaster, brick work, RCC work, floor, apran, other damaged part of Boundary Wall & Pump House of OHT campus/outside the campus including sorting and stacking of serviceable and disposal of unserviceable material within a distance of 8 km. For surface preparation, the cleaning of the exposed brick work/concrete surface shall be done with wire brushes. All brick work repairing in 1:4 cement and Coarse sand mortar and 12 mm thick plaster in 1:3 shall be done to repair the damaged structures. The floor and apran of the pump house shall be done with 100 mm PCC in 1:2:4 and 100 mm thick RCC with 1:1.5:3. The bye pass chamber of the pump house shall be repaired or reconstructed as per requirement of the site. All external surface of the pump house and boundary wall will be done in three coats of Apex Painting (Asian Apex Ultima exterior paint) over one coat primer of approved colour after finishing work. The painting work of internal surface of the pump house will be done with plastic paint. The roof top of the pump house shall be finished with new brick coba work including the replacement of rainwater pipes. All damaged doors and windows shall be replaced with new MS doors and windows. The MS Girder will be replaced if required. All works shall be done, including supply of all materials, labour, T&P etc. required for proper completion of the work as per the direction of the Engineer-in-Charge.(Payment 15% of the total amount of OHT/Boundary renovation items)Other miscellaneous works required for the proper functioning of water works as per the instructions of the engineer in charge(Payment 15% of the total amount of OHT/Boundary renovation items) |
| 18 | Renovation of existing 600 kl/20m staging OHT, boundary wall. At Zone -3 |
| 19 | Renovation of existing 150 kl/18m staging OHT, boundary wall. (04 nos OHTs at different locations, i.e. 4 Job @Rs. 952546.03 per each location ) |
| 20 | Renovation of existing 300 kl/18m staging OHT, boundary wall. At Zone -6 |
| 21 | Renovation of Pump house:Provide all materials, labour, T&P etc., complete and Renovate Pump house size (3.6x3.0x3.0)m, Chlorinating room size (1.80x2.50x3.0)m, as per departmental type design. This includes all necessary works/items its supply, installation/construction, etc., required to be done for the proper functioning of the scheme as per the design/ instruction of the engineer in charge |
| 22 | Distribution System & Rising Main:- |
| 23 | Supply of High-Density Polyethylene Pipes (HDPE):Supply of High-Density Polyethylene Pipes (HDPE) (PN-6) / PE-100, conforming to IS 4984 / 14151 / 12786 / 13488, in coils (90 mm & 100 mm) / standard lengths, with necessary jointing material like electro-fusion coupler, electro-fusion tee, electro-fusion band, electro-fusion reducer, flanged joint, including all statutory duties and taxes, pre-delivery third-party inspection charges (by M/s Crown Agents) and post-delivery testing, transit insurance, freight, transportation to store/site of work, unloading & stacking the same in covered shade duly protected from sun rays and rains, etc., complete as directed by the Engineer-in-Charge. |
| 24 | 110 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 25 | 140 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 26 | 160 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 27 | 180 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 28 | 200 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 29 | Supply of ISI mark DI K-7/K-9 S&S pipes (push on joints) (DI. K-9 for Rising main) of following class and diameters inclusive of jointing material (Rubber gasket of EPDM Quality, Bend, Tee etc.) including all statutary duties and taxes, third party inspection charges, transit insurance, freight, transportation to store/ site of work, unloading, stacking etc. complete as directed by Engineer –in-charge. |
| 30 | 125 mm dia D.I. Pipes (K-9) |
| 31 | 150 mm dia D.I. Pipes (K-9) |
| 32 | 300 mm dia D.I. Pipes (K-9) |
| 33 | 200 mm dia D.I. Pipes (K-7) |
| 34 | 250 mm dia D.I. Pipes (K-7) |
| 35 | 300 mm dia D.I. Pipes (K-7) |
| 36 | 350 mm dia D.I. Pipes (K-7) |
| 37 | Distribution System & Rising Main:- |
| 38 | Excavation of earth in ordinary soil (loam, clay or sand) for pipe line and rising main trenches including lift upto 1.50 m and lead upto 8 km and refilling watering, ramming of the excavated earth into the trench and also disposal of surplus earth upto 50m from the center of the trenches including supply of all material labour, T&P etc complete as per instructions of Engineer ‐in ‐charge. |
| 39 | Ordinary soil |
| 40 | Carting, Lowering, Laying & Testing |
| 41 | Carting, lowering, laying of following dia of HDPE Pipe (PN-6)/PE-100 of following dia and requisite specials to site of work, lowering them into trenches, laying true to alignment and gradient, in proper position, cutting of pipes, making of joints including cost of specials and fittings, crossing of all kind of Nala up to internal width upto 1.0 m (with 4 no of bends if required), labour, T&P, including hydraulic testing etc. complete as directed by Engineer-in-Charge.It includes provision for making of alignment on city roads, making trial pits to investigate location of various underground services like telephone cables, electric cables, existing pipe lines and sewer lines etc., arrangements for diversion of traffic and associated works etc. with supply of all necessary equipment, materials, labour and T&P etc. complete required for completion of work. The trenches shall be properly barricaded and fenced off wherever necessary. Red flags and caution boards during day and red lights during night shall be displayed so as to avoid any accidents.Note: Jointing between HDPE pipes and specials shall be done as per the latest IS:7634 Part II. Only bar-coded electro-fusion machine (automatically readable) that can read the bar code of the fittings automatically shall be used for jointing of HDPE Pipe/Fittings. |
| 42 | 110 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 43 | 140 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 44 | 160 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 45 | 180 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 46 | 200 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 47 | Carting, lowering, laying and jointing with SBR rubber gaskets D.I. K-7/K-9 pipes of following dia & pressure including all specials, to site of work, lowering them into trenches, laying true to alignment and gradient, in proper position, cutting of pipes, making of joints including cost of jointing materials and rubber rings, including crossing of Nala up to internal width upto 1.0 m (with 4 no. of bends if required), labour, T&P, including hydraulic testing etc. complete as directed by Engineer-in-Charge.It includes provision for making of alignment on city roads, making trial pits to investigate location of various underground services like telephone cables, electric cables, existing pipelines and sewer lines etc., arrangements for diversion of traffic and associated works etc. with supply of all necessary equipment, materials, labour and T&P etc. complete required for completion of work. The trenches shall be properly barricaded and fenced off wherever necessary. Red flags and caution boards during day and red lights during night shall be displayed so as to avoid any accidents.Note: Only SBR rubber gaskets to be used as per IS: 5382 and IS: 12820 |
| 48 | 125 mm dia D.I. Pipes (K-9) |
| 49 | 150 mm dia D.I. Pipes (K-9) |
| 50 | 300 mm dia D.I. Pipes (K-9) |
| 51 | 200 mm dia D.I. Pipes (K-7) |
| 52 | 250 mm dia D.I. Pipes (K-7) |
| 53 | 300 mm dia D.I. Pipes (K-7) |
| 54 | 350 mm dia D.I. Pipes (K-7) |
| 55 | Valves & Fittings |
| 56 | Supply and carting up to site of work of the following dia DI sluice valves (AVK/VAG), class I, working pressure 16 Kg/cm2 confirming to IS: 780/1969 or its latest amendments , including valve fittings & Dismantling Joints as per requirement F.O.R. destination, and lowering them into the already prepared trenches, fixing in position and jointing them with pipelines and testing etc. complete and also including supply of jointing materials etc. complete .including all taxes and insurance, as per instructions of Engineer -in -charge. |
| 57 | 350 mm dia |
| 58 | 300 mm dia |
| 59 | 250 mm dia |
| 60 | 200 mm dia |
| 61 | 150 mm dia |
| 62 | 125 mm dia |
| 63 | 100 mm dia |
| 64 | Scoure Valve |
| 65 | 80 mm dia to 90 mm dia |
| 66 | Kinetic Couble Air Valves |
| 67 | 25 mm dia |
| 68 | Fire Hydrant PN 1.6 (as per IS Code 908:1975) |
| 69 | 80 mm dia |
| 70 | Supply of all labour, materials, fittings and specials required for crossing of nala (with 4 no. of bends, if required) along the alignment of pipeline using the casing pipe more than 1.25 times the diameter of the carrier pipe, including making of necessary trench or bore hole below the bed of the nala for proper completion of the work.In case the nala crossing is required to be done above the top of the nala, 6 mm thick MS casing pipe shall be used.All kinds of dewatering and proper barricading works will be done as per instructions of the Engineer-in-Charge. |
| 71 | Road/Nala (big)/culvert crossing more than 3.5m width |
| 72 | Road/Nala crossing (small) upto 3.5m width |
| 73 | Supply of all materials, labour, T&P etc required for construction of brick masnory chambers for valves mentioned below. It includes excavation& Disposal of surplus earth, 100 mm thick PCC of 1:2:4 , brick work in 1:4, 12 mm thick plaster in 1:4 and precast RCC (M25 grade) Cover of thickness 150 mm as per the directions of Engineer-in- charge. |
| 74 | Sluice valve chamber (surface box Type) |
| 75 | Sluice valve chamber (masonry Type) - dia above 200 mm ‐ 1000 (L) x 1200 (W) x 1300 (H) mm |
| 76 | Fire Hydrant chamber (750 (L) X 450 (W) X 1000 (H) mm) |
| 77 | Air Valve Chamber 350 (L) x 350 (W) x 500 (H) mm |
| 78 | Road dismantling and restoration |
| 79 | Dismantling of the following type of road surface with old and new materials including supply of all materials, labour, T&P etc. required for proper completion of the work as per instructions of Engineer‐in‐Charge.Note:– The dismantling of bituminous/CC roads shall be done only using the bituminous/CC road cutters or breakers in the true alignment of the pipe line. In case of tiles, only manual dismantling will be permitted. If the road cutting is being done directly by the JCB resulting in unnecessary extra road surface damaging, the deduction for extra damaged surface area shall be done on the basis of rates provided for its reinstatement |
| 80 | Bituminous surface- |
| 81 | Interlocking Road |
| 82 | C.C. Road |
| 83 | BOE Road |
| 84 | Reinstatement of Road:Permanent re-instatement of following type of road surfaces after laying of pipe line including supply of all materials, labour, T&P etc. required for completion of work. It also includes necessary excavation required for preparation of trench for reinstatement of road, disposal of surplus unserviceable material, watering, ramming, cleaning of surface for proper completion of the work as per directions of Engineer-in-Charge.Note:– Before starting the reinstatement work, it will be ensured that the trench has been compacted to achieve the required limits using mechanical vibrator-based compactor (Electric/Petrol operated). If the trench is not compacted with the mechanical vibrator-based compactor, then 10% deduction will be applied for payment of reinstatement of the roads |
| 85 | Nagar Nigam/ Nagar Palika Bituminous Road |
| 86 | Construction of bitumen road including supply of all materials, labour, T&P etc. required for proper completion of work as per following specification:-GSB = 27.5 cmBM (One coat) = 7.5 cm (Min. Bit. content - 3.0 %) BC (One coat) = 3.0 cm (Min. Bit. content - 5.0 %) |
| 87 | PWD Bituminous Road |
| 88 | Construction of bitumen road as per UPPWD specification including supply of all materials, labour, T&P etc. required for proper completion of work as per following thickness:-Local sand filling = 69.0 cmGSB = 25.0 cmWMM = 20.0 cmBM (One coat) = 10.0 cm (Min. Bit. content - 3.0 %) BC (One coat) = 4.0 cm(Min. Bit. content - 5.0 %) |
| 89 | CC Road:supply of all materials, labour, T&P etc. required for Construction of Cement Concrete road spreading and mechanically compacting by using needle and surface vibrators, levelling to required slope / camber, finishing upto proper completion of work as per following thickness :-PCC = 100 mm,1:2:4 (cement, coarse sand & stone ballast of 20-40 mm) CC =100 mm, 1:1.5 :3 (cement, coarse sand & stone ballast of 16-20 mm) |
| 90 | Interlocking Tiles Road:Construction of C.C. Interlocking Tile road including supply of all materials, labour, T&P etc. required for proper completion of work as per following thickness:-PCC = 100 mm,1:2:4 (cement, coarse sand & stone ballast of 20-40 mm)Sand = 30mm to 50mm thick local sand lair for preparation of surfaceTiles = Serviceable Interlocking Tiles recived from dismantling + New Interlocking TilesNote : 80 mm thick rubber moulded interlocking tile of M-30 shall be used for construction of interlocking tile road. |
| 91 | BOE ROADSupply of all materials, labour, T&P etc required for reinstatment BOE road including Serviceable briks recived from dismantling and using of new bricks as per requirment of site as per the directions and satification of Engineer-in- charge. |
| 92 | Thrust Block:Providing and laying in position reinforced cement concrete (mix 1:2:4) for construction of thurst block at bends of feeder main, rising main & distribution system including providing & fixing of steel reinforcement as per design, batching, mixing, placing, vibrating, curing, formwork, finishing, including cost of all material and labor, tools and plants required with transportation, loading, unloading, etc., complete for all leads and lifts etc required for proper completion of the work. |
| 93 | HOUSE CONNECTION:Providing and making water supply house connection from distribution pipeline of following diameters using 20 mm dia pipe (HDPE pipe (PE 100 / PN 12.5) below ground and medium class GI pipe above ground), saddle (electro-fusion tapping saddle for making connection with HDPE distribution pipeline, DI strap saddle, ferrule for making connection with distribution pipeline other than HDPE), transition coupler fittings (PE 100 / SDR 11 / 16 bar FTA, MTA with one end electro-fusion), ball valve, specials, including supply of all materials, labour, T&P etc. required for proper completion of the work.It also includes excavation, refilling of pit required for making house connection in following type of pipeline |
| 94 | HDPE PIPE 110 mm to 180 mm dia |
| 95 | 200 mm- 450 mm DIA D.I. Pipes (K-7) |
| 96 | Shifting House Connection |
| 97 | Provision of new single Brass tap ferrule water house hold Connection with fixing of saddle (electrofusion tapping saddle) for making connection with HDPE distribution pipeline, DI strap saddle, ferrule for making connection with pipes other than HDPE, connection fittings, GM ferrule of 15mm dia including brass tape with welded, 20mm dia (OD) HDPE pipe (PE-100/ PN-12.5) and 20mm dia OD G.I pipe Class B upto house holder as per type design drawings and .including excavation, laying and jointing for proper completion of work as per instructions of Engineer-in-charge |
| 98 | HDPE PIPE 110 mm to 180 mm dia |
| 99 | 200 mm-450 mm DIA D.I. Pipes (K-7) |
| 100 | Provision of inter Connection |
| 101 | Provision of Interconnection in existing pipe network DI/AC/PVC/HDPE pipe including supply, carting of specials, lowering them into trenches, cutting, fixing in proper alignment including bailing out water etc all necessary works complete upto the satisfaction of Engineer-in-charge. |
| 102 | 80 mm dia - 350 mm dia |
| 103 | Aproach Road:Construction of C.C. Interlocking Tile approach road road including supply of all materials, labour, T&P etc. required for proper completion of work as per following thickness:-PCC = 100 mm,1:3:6 (cement, coarse sand & stone ballast of 20-40 mm)Sand = 30mm to 50mm thick local sand lair for preparation of surfaceTiles = 100% new Note : 80 mm thick rubber moulded interlocking tile of M-30 shall be used for construction of interlocking tile road. |
| 104 | Boundary Wall and MS Gate:Supply of all labour, materials and T&P etc. required for construction of boundary wall of OHT/TW campus including fabrication and fixing of 3.60 m wide MS main gate and 1.0 m wide wicket gate (four no. of gates will be required at different locations and average 85 m boundary wall at each location) as per departmental type design and drawing for boundary wall and MS gate.The height of MS gate and wicket gate shall not be less than 1.8 m. The depth of foundation may increase with the site conditions of the water works campus, and the plinth beam will be minimum 30 cm above the formation level of the campus for proper completion of work to the complete satisfaction of the Engineer-in-Charge. |
| 105 | Staff Quarter:Supply of all material, T&P etc. required for construction of Staff Quarter with RCC framed structure, adopting the depth of foundation not less than 1.20 m from the natural ground level, including all civil, electrical and plumbing/sanitary fittings, sanitary toilet with soak pit, MS doors & grill windows (minimum 12 Gauge). The windows will be facilitated with mosquito net, including two coats of Apex Ultima exterior paint over one coat of primer, and enamel paint on MS works.The flooring of the staff quarter will be done by using 8 mm vitrified tiles of Somany/Kajaria for proper completion of work as per departmental type design and drawing, to the complete satisfaction of the Engineer-in-ChargeZONE-6 and ZONE-9 |
| 106 | MCS RoomSupply of all material, T&P etc. required for construction of MCS room with RCC framed structure, adopting the depth of foundation not less than 1.20 m from the natural ground level, including all civil, electrical and plumbing/sanitary fittings, sanitary toilet with soak pit, UPVC doors & windows, including two coats of Apex Ultima exterior paint over one coat of primer.The flooring of the MCS room will be done by using 8 mm vitrified tiles of Somany/Kajaria for proper completion of work to the complete satisfaction of the Engineer-in-Charge |
| 107 | Rain Water Harvesting UnitDesign, submission of vetted design from IIT/NIT, drawing, and supply of all material, T&P etc. required for construction of rain water harvesting recharge pit, including 2 Nos. of bores up to the 1st strata of water table using minimum 160 mm PVC pipe of 8 kg/cm².It includes the construction of inlet and overflow chamber of minimum 0.6 m x 0.6 m (RCC M-20), 350 mm thick brick wall on appropriate foundation up to required depth as per design and drawing, with filling of media in required layers and thickness.A piezometer shall be installed for obtaining information regarding the water table, as per direction of the Engineer-in-Charge. |
| 108 | Earth filling in TW campus (other than OHT campus):Supply of all materials, tools and plants for filling of earth in the TW campus including site preparation, surface leveling, earth filling or lifting to achieve the required formation level, plantation, and all other associated activities. The work shall be carried out in accordance with the specifications and to the complete satisfaction of the Engineer-in-Charge. |
| 109 | Zone-01 |
| 110 | Pumping plant & Instrumentation for Exsting Tubewell |
| 111 | SITC of 800 LPM, 68 M head (Both Tentative) Submersible pump motor set with 24m 150/100 mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 no) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 112 | Submersible Pump Motor Set 800 LPM 68 M head (Both Tentative) as Spare for Scheme |
| 113 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 114 | 3M long heavy duty coloum pipe (spare) |
| 115 | Automatic chlorination System |
| 116 | CE/UL Certified Intelligent Smart Energy Meter |
| 117 | Motor Operated Actuator with 150/100 mm dia DI sluice valve |
| 118 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 119 | Digital Soft starter / VFD with RS485 Port- 400V Class, 22 KW or higher suitable Rating. |
| 120 | CE/UL Certified Pressure transmitter |
| 121 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 122 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 123 | CE/UL certified surge protector for control panel |
| 124 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 125 | Automation work for existing TW |
| 126 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 127 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in tender technical specification |
| 128 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 129 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 130 | Installation, Testing and Commissioning for one Tubewell |
| 131 | Successful trial run till hand over the scheme to concerning ULB |
| 132 | Proposed E&M Work at ESR For Zone-01 |
| 133 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 200 mm |
| 134 | Electro Magnetic Flowmeter (Outlet of ESR) Size 200 mm |
| 135 | Flow Control Valve suitable for drinking water Size 200 mm |
| 136 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 137 | Mannual Pressure Transmitter with display |
| 138 | Automatic Chlorination System |
| 139 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 140 | Smart pressure transmitter |
| 141 | Control panel with all other required equipment for scada |
| 142 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 143 | Automation Work at ESR |
| 144 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 145 | CE/UL Certified Radar type level transmitter for OHT |
| 146 | Zone-02 |
| 147 | Pumping plant & Instrumentation for Exsting Tubewell |
| 148 | SITC of 800 LPM, 68 M head (Both Tentative) Submersible pump motor set with 24m 150/100 mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 no) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 149 | Submersible Pump Motor Set 800 LPM 68 M head (Both Tentative) as Spare for Scheme |
| 150 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 151 | 3M long heavy duty coloum pipe (spare) |
| 152 | Automatic chlorination System |
| 153 | CE/UL Certified Intelligent Smart Energy Meter |
| 154 | Motor Operated Actuator with 150/100 mm dia DI sluice valve |
| 155 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 156 | Digital Soft starter / VFD with RS485 Port- 400V Class, 22 KW or higher suitable Rating. |
| 157 | CE/UL Certified Pressure transmitter |
| 158 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 159 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 160 | CE/UL certified surge protector for control panel |
| 161 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 162 | Automation work for existing TW |
| 163 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 164 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in tender technical specification |
| 165 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 166 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 167 | Installation, Testing and Commissioning for one Tubewell |
| 168 | Successful trial run till hand over the scheme to concerning ULB |
| 169 | Proposed E&M Work at ESR For Zone-02 |
| 170 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 200 mm |
| 171 | Electro Magnetic Flowmeter (Outlet of ESR) Size 200 mm |
| 172 | Flow Control Valve suitable for drinking water Size 200 mm |
| 173 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 174 | Mannual Pressure Transmitter with display |
| 175 | Automatic Chlorination System |
| 176 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 177 | Smart pressure transmitter |
| 178 | Control panel with all other required equipment for scada |
| 179 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 180 | Automation Work at ESR |
| 181 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 182 | CE/UL Certified Radar type level transmitter for OHT |
| 183 | Zone-03 |
| 184 | Construction of New Tubewell |
| 185 | Transportation, Erection & Dismantling of Rig Machine |
| 186 | Transportation of Tubewell Assembly |
| 187 | Transportation, Erection & Dismantling of 350 PSI Air Compressor |
| 188 | Transportation, Erection & Dismantling of 3 Cusec O.P Unit |
| 189 | DC Drilling upto 200 M |
| 190 | Drilling of 625 mm. dia bore from G.L. to 70 m BGL. |
| 191 | Drilling of 500 mm.dia bore from 70 M bgl to 100 m BGL. |
| 192 | Drilling of 500 mm.dia bore from 100 M bgl to 200 m BGL. |
| 193 | Bentonite Clay |
| 194 | Flushing of Bore |
| 195 | Electrical Logging of the Bore |
| 196 | M.S. Tubewell assembly with all required parts like plain pipe, slotted pipe (as required upto 50% of plain pipes) well cap, bail pliug, clamp, reducer, centre guide, support structure etc as required & as per typed design complete in all respect. |
| 197 | 300 mm.dia size |
| 198 | 200 mm.dia size |
| 199 | Supply of 1.6 mm to 4.8 mm size pea gravel duly screened and washed as per IS 4097 |
| 200 | Lowering of 300X200 mm.dia tube well assembly duly welded including welding electrode and shrouding of pea gravel complete in all respect. |
| 201 | 300mm dia MS ERW pipe from G.L. to 65 m BGL |
| 202 | 200 mm.dia M.S ERW plain/ slotted pipe from 65 m BGL to 100 m BGL |
| 203 | 200 mm.dia M.S ERW plain/ slotted pipe from 100 m BGL to 180 m BGL |
| 204 | Development of Tubewell |
| 205 | Development of Tube well by 350 PSI Air Compressor |
| 206 | Development of Tube well by 3 Cusec O.P. Unit |
| 207 | TEST : |
| 208 | Chemical and Bacteriological test of water sample from departmental approved lab |
| 209 | Watch & ward during construction of TW |
| 210 | Pumping Plant & Instrumentation For New Tubewell |
| 211 | SITC of 1200 LPM, 62 M head (Both Tentative) Submersible pump motor set with 24m 150mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 nos) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 212 | Submersible Pump Motor Set 1200 LPM 62 M head (Both Tentative) as Spare for Scheme |
| 213 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 214 | 3M long heavy duty coloum pipe (spare) |
| 215 | Automatic chlorination System |
| 216 | CE/UL Certified Intelligent Smart Energy Meter |
| 217 | Motor Operated Actuator with 150 mm dia DI sluice valve |
| 218 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 219 | Digital Soft starter / VFD with RS485 Port- 400V Class, 30 KW or higher suitable Rating. |
| 220 | CE/UL Certified Pressure transmitter |
| 221 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 222 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 223 | CE/UL certified surge protector for control panel |
| 224 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 225 | Pumping plant & Instrumentation for Exsting Tubewell |
| 226 | SITC of 800 LPM, 68 M head (Both Tentative) Submersible pump motor set with 24m 150/100 mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 no) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 227 | Submersible Pump Motor Set 800 LPM 68 M head (Both Tentative) as Spare for Scheme |
| 228 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 229 | 3M long heavy duty coloum pipe (spare) |
| 230 | Automatic chlorination System |
| 231 | CE/UL Certified Intelligent Smart Energy Meter |
| 232 | Motor Operated Actuator with 150/100 mm dia DI sluice valve |
| 233 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 234 | Digital Soft starter / VFD with RS485 Port- 400V Class, 22 KW or higher suitable Rating. |
| 235 | CE/UL Certified Pressure transmitter |
| 236 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 237 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 238 | CE/UL certified surge protector for control panel |
| 239 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 240 | Automation work for New & Existing TW |
| 241 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 242 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in tender technical specification |
| 243 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 244 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 245 | Installation, Testing and Commissioning for one Tubewell |
| 246 | Successful trial run till hand over the scheme to concerning ULB |
| 247 | Proposed E&M Work at ESR For Zone-03 |
| 248 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 250 mm |
| 249 | Electro Magnetic Flowmeter (Outlet of ESR) Size 250 mm |
| 250 | Flow Control Valve suitable for drinking water Size 250 mm |
| 251 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 252 | Mannual Pressure Transmitter with display |
| 253 | Automatic Chlorination System |
| 254 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 255 | Smart pressure transmitter |
| 256 | Control panel with all other required equipment for scada |
| 257 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 258 | Expenditure on trial run of all Tubewells including all operating / maintenance staff as per tender / DPR, chlorine and all other consumables with electricity charges till hand over the scheme to concerning ULB |
| 259 | Automation Work at ESR |
| 260 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 261 | CE/UL Certified Radar type level transmitter for OHT |
| 262 | Zone-04 |
| 263 | Pumping plant & Instrumentation for Existing Tubewell |
| 264 | SITC of 800 LPM, 68 M head (Both Tentative) Submersible pump motor set with 24m 150/100 mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 no) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 265 | Submersible Pump Motor Set 800 LPM 68 M head (Both Tentative) as Spare for Scheme |
| 266 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 267 | 3M long heavy duty coloum pipe (spare) |
| 268 | Automatic chlorination System |
| 269 | CE/UL Certified Intelligent Smart Energy Meter |
| 270 | Motor Operated Actuator with 150/100 mm dia DI sluice valve |
| 271 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 272 | Digital Soft starter / VFD with RS485 Port- 400V Class, 22 KW or higher suitable Rating. |
| 273 | CE/UL Certified Pressure transmitter |
| 274 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 275 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 276 | CE/UL certified surge protector for control panel |
| 277 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 278 | Automation work for existing TW |
| 279 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 280 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in tender technical specification |
| 281 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 282 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 283 | Installation, Testing and Commissioning for one Tubewell |
| 284 | Successful trial run till hand over the scheme to concerning ULB |
| 285 | Proposed E&M Work at ESR For Zone-04 |
| 286 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 350 mm |
| 287 | Electro Magnetic Flowmeter (Outlet of ESR) Size 350 mm |
| 288 | Flow Control Valve suitable for drinking water Size 350 mm |
| 289 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 290 | Mannual Pressure Transmitter with display |
| 291 | Automatic Chlorination System |
| 292 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 293 | Smart pressure transmitter |
| 294 | Control panel with all other required equipment for scada |
| 295 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 296 | Automation Work at ESR |
| 297 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 298 | CE/UL Certified Radar type level transmitter for OHT |
| 299 | Zone-05 |
| 300 | Pumping plant & Instrumentation for Exsting Tubewell |
| 301 | SITC of 800 LPM, 68 M head (Both Tentative) Submersible pump motor set with 24m 150/100 mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 no) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 302 | Submersible Pump Motor Set 800 LPM 68 M head (Both Tentative) as Spare for Scheme |
| 303 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 304 | 3M long heavy duty coloum pipe (spare) |
| 305 | Automatic chlorination System |
| 306 | CE/UL Certified Intelligent Smart Energy Meter |
| 307 | Motor Operated Actuator with 150/100 mm dia DI sluice valve |
| 308 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 309 | Digital Soft starter / VFD with RS485 Port- 400V Class, 22 KW or higher suitable Rating. |
| 310 | CE/UL Certified Pressure transmitter |
| 311 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 312 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 313 | CE/UL certified surge protector for control panel |
| 314 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 315 | Automation work for existing TW |
| 316 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 317 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in tender technical specification |
| 318 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 319 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 320 | Installation, Testing and Commissioning for one Tubewell |
| 321 | Successful trial run till hand over the scheme to concerning ULB |
| 322 | Proposed E&M Work at ESR For Zone-05 |
| 323 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 200 mm |
| 324 | Electro Magnetic Flowmeter (Outlet of ESR) Size 200 mm |
| 325 | Flow Control Valve suitable for drinking water Size 200 mm |
| 326 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 327 | Mannual Pressure Transmitter with display |
| 328 | Automatic Chlorination System |
| 329 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 330 | Smart pressure transmitter |
| 331 | Control panel with all other required equipment for scada |
| 332 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 333 | Automation Work at ESR |
| 334 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 335 | CE/UL Certified Radar type level transmitter for OHT |
| 336 | Zone-06 |
| 337 | Construction of New Tubewell |
| 338 | Transportation, Erection & Dismantling of Rig Machine |
| 339 | Transportation of Tubewell Assembly |
| 340 | Transportation, Erection & Dismantling of 350 PSI Air Compressor |
| 341 | Transportation, Erection & Dismantling of 3 Cusec O.P Unit |
| 342 | DC Drilling upto 200 M |
| 343 | Drilling of 625 mm. dia bore from G.L. to 70 m BGL. |
| 344 | Drilling of 500 mm.dia bore from 70 M bgl to 100 m BGL. |
| 345 | Drilling of 500 mm.dia bore from 100 M bgl to 200 m BGL. |
| 346 | Bentonite Clay |
| 347 | Flushing of Bore |
| 348 | Electrical Logging of the Bore |
| 349 | M.S. Tubewell assembly with all required parts like plain pipe, slotted pipe (as required upto 50% of plain pipes) well cap, bail pliug, clamp, reducer, centre guide, support structure etc as required & as per typed design complete in all respect. |
| 350 | 300 mm.dia size |
| 351 | 200 mm.dia size |
| 352 | Supply of 1.6 mm to 4.8 mm size pea gravel duly screened and washed as per IS 4097 |
| 353 | Lowering of 300X200 mm.dia tube well assembly duly welded including welding electrode and shrouding of pea gravel complete in all respect. |
| 354 | 300mm dia MS ERW pipe from G.L. to 65 m BGL |
| 355 | 200 mm.dia M.S ERW plain/ slotted pipe from 65 m BGL to 100 m BGL |
| 356 | 200 mm.dia M.S ERW plain/ slotted pipe from 100 m BGL to 180 m BGL |
| 357 | Development of Tubewell |
| 358 | Development of Tube well by 350 PSI Air Compressor |
| 359 | Development of Tube well by 3 Cusec O.P. Unit |
| 360 | TEST : |
| 361 | Chemical and Bacteriological test of water sample from departmental approved lab |
| 362 | Watch & ward during construction of TW |
| 363 | Pumping Plant & Instrumentation For New Tubewell |
| 364 | SITC of 1200 LPM, 62 M head (Both Tentative) Submersible pump motor set with 24m 150mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 nos) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 365 | Submersible Pump Motor Set 1200 LPM 62 M head (Both Tentative) as Spare for Scheme |
| 366 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 367 | 3M long heavy duty coloum pipe (spare) |
| 368 | Automatic chlorination System |
| 369 | CE/UL Certified Intelligent Smart Energy Meter |
| 370 | Motor Operated Actuator with 150 mm dia DI sluice valve |
| 371 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 372 | Digital Soft starter / VFD with RS485 Port- 400V Class, 30 KW or higher suitable Rating. |
| 373 | CE/UL Certified Pressure transmitter |
| 374 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 375 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 376 | CE/UL certified surge protector for control panel |
| 377 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 378 | Automation work for New TW |
| 379 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 380 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in tender technical specification |
| 381 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 382 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 383 | Installation, Testing and Commissioning for one Tubewell |
| 384 | Successful trial run till hand over the scheme to concerning ULB |
| 385 | Proposed E&M Work at ESR For Zone-06 |
| 386 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 300 mm |
| 387 | Electro Magnetic Flowmeter (Outlet of ESR) Size 300 mm |
| 388 | Flow Control Valve suitable for drinking water Size 300 mm |
| 389 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 390 | Mannual Pressure Transmitter with display |
| 391 | Automatic Chlorination System |
| 392 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 393 | Smart pressure transmitter |
| 394 | Control panel with all other required equipment for scada |
| 395 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 396 | Expenditure on trial run of all Tubewells including all operating / maintenance staff as per tender / DPR, chlorine and all other consumables with electricity charges till hand over the scheme to concerning ULB |
| 397 | Automation Work at ESR |
| 398 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 399 | CE/UL Certified Radar type level transmitter for OHT |
| 400 | Zone-07 |
| 401 | Construction of New Tubewell |
| 402 | Transportation, Erection & Dismantling of Rig Machine |
| 403 | Transportation of Tubewell Assembly |
| 404 | Transportation, Erection & Dismantling of 350 PSI Air Compressor |
| 405 | Transportation, Erection & Dismantling of 3 Cusec O.P Unit |
| 406 | DC Drilling upto 200 M |
| 407 | Drilling of 625 mm. dia bore from G.L. to 70 m BGL. |
| 408 | Drilling of 500 mm.dia bore from 70 M bgl to 100 m BGL. |
| 409 | Drilling of 500 mm.dia bore from 100 M bgl to 200 m BGL. |
| 410 | Bentonite Clay |
| 411 | Flushing of Bore |
| 412 | Electrical Logging of the Bore |
| 413 | M.S. Tubewell assembly with all required parts like plain pipe, slotted pipe (as required upto 50% of plain pipes) well cap, bail pliug, clamp, reducer, centre guide, support structure etc as required & as per typed design complete in all respect. |
| 414 | 300 mm.dia size |
| 415 | 200 mm.dia size |
| 416 | Supply of 1.6 mm to 4.8 mm size pea gravel duly screened and washed as per IS 4097 |
| 417 | Lowering of 300X200 mm.dia tube well assembly duly welded including welding electrode and shrouding of pea gravel complete in all respect. |
| 418 | 300mm dia MS ERW pipe from G.L. to 65 m BGL |
| 419 | 200 mm.dia M.S ERW plain/ slotted pipe from 65 m BGL to 100 m BGL |
| 420 | 200 mm.dia M.S ERW plain/ slotted pipe from 100 m BGL to 180 m BGL |
| 421 | Development of Tubewell |
| 422 | Development of Tube well by 350 PSI Air Compressor |
| 423 | Development of Tube well by 3 Cusec O.P. Unit |
| 424 | TEST : |
| 425 | Chemical and Bacteriological test of water sample from departmental approved lab |
| 426 | Watch & ward during construction of TW |
| 427 | Pumping Plant & Instrumentation For New Tubewell |
| 428 | SITC of 1200 LPM, 62 M head (Both Tentative) Submersible pump motor set with 24m 150mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 nos) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 429 | Submersible Pump Motor Set 1200 LPM 62 M head (Both Tentative) as Spare for Scheme |
| 430 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 431 | 3M long heavy duty coloum pipe (spare) |
| 432 | Automatic chlorination System |
| 433 | CE/UL Certified Intelligent Smart Energy Meter |
| 434 | Motor Operated Actuator with 150 mm dia DI sluice valve |
| 435 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 436 | Digital Soft starter / VFD with RS485 Port- 400V Class, 30 KW or higher suitable Rating. |
| 437 | CE/UL Certified Pressure transmitter |
| 438 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 439 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 440 | CE/UL certified surge protector for control panel |
| 441 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 442 | Pumping plant & Instrumentation for Exsting Tubewell |
| 443 | SITC of 800 LPM, 68 M head (Both Tentative) Submersible pump motor set with 24m 150/100 mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 no) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 444 | Submersible Pump Motor Set 800 LPM 68 M head (Both Tentative) as Spare for Scheme |
| 445 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 446 | 3M long heavy duty coloum pipe (spare) |
| 447 | Automatic chlorination System |
| 448 | CE/UL Certified Intelligent Smart Energy Meter |
| 449 | Motor Operated Actuator with 150/100 mm dia DI sluice valve |
| 450 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 451 | Digital Soft starter / VFD with RS485 Port- 400V Class, 22 KW or higher suitable Rating. |
| 452 | CE/UL Certified Pressure transmitter |
| 453 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 454 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 455 | CE/UL certified surge protector for control panel |
| 456 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 457 | Automation work for New TW |
| 458 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 459 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in tender technical specification |
| 460 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 461 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 462 | Installation, Testing and Commissioning for one Tubewell |
| 463 | Successful trial run till hand over the scheme to concerning ULB |
| 464 | Proposed E&M Work at ESR For DMA-01 (Zone-07) |
| 465 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 250 mm |
| 466 | Electro Magnetic Flowmeter (Outlet of ESR) Size 250 mm |
| 467 | Flow Control Valve suitable for drinking water Size 250 mm |
| 468 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 469 | Mannual Pressure Transmitter with display |
| 470 | Automatic Chlorination System |
| 471 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 472 | Smart pressure transmitter |
| 473 | Control panel with all other required equipment for scada |
| 474 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 475 | Proposed E&M Work at ESR For DMA-02 (Zone-07) |
| 476 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 300 mm |
| 477 | Electro Magnetic Flowmeter (Outlet of ESR) Size 300 mm |
| 478 | Flow Control Valve suitable for drinking water Size 300 mm |
| 479 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 480 | Mannual Pressure Transmitter with display |
| 481 | Automatic Chlorination System |
| 482 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 483 | Smart pressure transmitter |
| 484 | Control panel with all other required equipment for scada |
| 485 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 486 | Expenditure on trial run of all Tubewells including all operating / maintenance staff as per tender / DPR, chlorine and all other consumables with electricity charges till hand over the scheme to concerning ULB |
| 487 | Automation Work at ESR |
| 488 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 489 | CE/UL Certified Radar type level transmitter for OHT |
| 490 | Zone-08 |
| 491 | Pumping plant & Instrumentation for Exsting Tubewell |
| 492 | SITC of 800 LPM, 68 M head (Both Tentative) Submersible pump motor set with 24m 150/100 mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 no) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 493 | Submersible Pump Motor Set 800 LPM 68 M head (Both Tentative) as Spare for Scheme |
| 494 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 495 | 3M long heavy duty coloum pipe (spare) |
| 496 | Automatic chlorination System |
| 497 | CE/UL Certified Intelligent Smart Energy Meter |
| 498 | Motor Operated Actuator with 150/100 mm dia DI sluice valve |
| 499 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 500 | Digital Soft starter / VFD with RS485 Port- 400V Class, 22 KW or higher suitable Rating. |
| 501 | CE/UL Certified Pressure transmitter |
| 502 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 503 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 504 | CE/UL certified surge protector for control panel |
| 505 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 506 | Automation work for existing TW |
| 507 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 508 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in tender technical specification |
| 509 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 510 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 511 | Installation, Testing and Commissioning for one Tubewell |
| 512 | Successful trial run till hand over the scheme to concerning ULB |
| 513 | Proposed E&M Work at ESR For Zone-08 |
| 514 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 200 mm |
| 515 | Electro Magnetic Flowmeter (Outlet of ESR) Size 200 mm |
| 516 | Flow Control Valve suitable for drinking water Size 200 mm |
| 517 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 518 | Mannual Pressure Transmitter with display |
| 519 | Automatic Chlorination System |
| 520 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 521 | Smart pressure transmitter |
| 522 | Control panel with all other required equipment for scada |
| 523 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 524 | Automation Work at ESR |
| 525 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 526 | CE/UL Certified Radar type level transmitter for OHT |
| 527 | Zone-09 |
| 528 | Construction of New Tubewell |
| 529 | Transportation, Erection & Dismantling of Rig Machine |
| 530 | Transportation of Tubewell Assembly |
| 531 | Transportation, Erection & Dismantling of 350 PSI Air Compressor |
| 532 | Transportation, Erection & Dismantling of 3 Cusec O.P Unit |
| 533 | DC Drilling upto 200 M |
| 534 | Drilling of 625 mm. dia bore from G.L. to 70 m BGL. |
| 535 | Drilling of 500 mm.dia bore from 70 M bgl to 100 m BGL. |
| 536 | Drilling of 500 mm.dia bore from 100 M bgl to 200 m BGL. |
| 537 | Bentonite Clay |
| 538 | Flushing of Bore |
| 539 | Electrical Logging of the Bore |
| 540 | M.S. Tubewell assembly with all required parts like plain pipe, slotted pipe (as required upto 50% of plain pipes) well cap, bail pliug, clamp, reducer, centre guide, support structure etc as required & as per typed design complete in all respect. |
| 541 | 300 mm.dia size |
| 542 | 200 mm.dia size |
| 543 | Supply of 1.6 mm to 4.8 mm size pea gravel duly screened and washed as per IS 4097 |
| 544 | Lowering of 300X200 mm.dia tube well assembly duly welded including welding electrode and shrouding of pea gravel complete in all respect. |
| 545 | 300mm dia MS ERW pipe from G.L. to 65 m BGL |
| 546 | 200 mm.dia M.S ERW plain/ slotted pipe from 65 m BGL to 100 m BGL |
| 547 | 200 mm.dia M.S ERW plain/ slotted pipe from 100 m BGL to 180 m BGL |
| 548 | Development of Tubewell |
| 549 | Development of Tube well by 350 PSI Air Compressor |
| 550 | Development of Tube well by 3 Cusec O.P. Unit |
| 551 | TEST : |
| 552 | Chemical and Bacteriological test of water sample from departmental approved lab |
| 553 | Watch & ward during construction of TW |
| 554 | Pumping Plant & Instrumentation For New Tubewell |
| 555 | SITC of 1200 LPM, 62 M head (Both Tentative) Submersible pump motor set with 24m 150mm dia coloum pipe, NRV, CI D/F Bend 90º, CI A/F Tee, D/F Pipe (1.5 m long 02 nos & 1.0 m long 01 nos) Earthing, Painting, Tools sets, wiring of pump house internal & external, Chain pulley block & all Pumping Plant accessories with nut bolts and rubber packing etc. |
| 556 | Submersible Pump Motor Set 1200 LPM 62 M head (Both Tentative) as Spare for Scheme |
| 557 | SITC of Scada compatible Servo Voltage Stabilizer of suitable capacity with all required necessary accessories like SPP, TDR, HL cut off, RS 485 port for scada compatibility, overload protection, bypass arrangement and body earthing etc complete in all respect. |
| 558 | 3M long heavy duty coloum pipe (spare) |
| 559 | Automatic chlorination System |
| 560 | CE/UL Certified Intelligent Smart Energy Meter |
| 561 | Motor Operated Actuator with 150 mm dia DI sluice valve |
| 562 | CE/UL Certified Electromagnetic Flowmeter of size 150 mm |
| 563 | Digital Soft starter / VFD with RS485 Port- 400V Class, 30 KW or higher suitable Rating. |
| 564 | CE/UL Certified Pressure transmitter |
| 565 | CE/UL certified hydrostatic type sub soil water level transmitter for tubewells |
| 566 | Auto Phase Reversal Unit Suitble for above pumping plant with Inbuilt time delay and Enclosure (confirmation to IEC:60947-1 & IEC: 60947-b-1) 250 Amp |
| 567 | CE/UL certified surge protector for control panel |
| 568 | Complete cabling for Tubewell including all power & control cables of all equipments at pump house and OHT |
| 569 | Automation work for New TW |
| 570 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 571 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in tender technical specification |
| 572 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 573 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 574 | Installation, Testing and Commissioning for one Tubewell |
| 575 | Successful trial run till hand over the scheme to concerning ULB |
| 576 | Proposed E&M Work at ESR For Zone-09 |
| 577 | Isolation DI Sluice Valve with Actuator (Outlet of ESR) 250 mm |
| 578 | Electro Magnetic Flowmeter (Outlet of ESR) Size 250 mm |
| 579 | Flow Control Valve suitable for drinking water Size 250 mm |
| 580 | Isolation DI Sluice Valve with Actuator Spare for ESR |
| 581 | Mannual Pressure Transmitter with display |
| 582 | Automatic Chlorination System |
| 583 | Battery operated / electricity or both (as per engineer encharge) Chlorine Analyser |
| 584 | Smart pressure transmitter |
| 585 | Control panel with all other required equipment for scada |
| 586 | CE/UL certified Sutable capacity UPS with batteries at ESR for operation of actuators & other equipments if required |
| 587 | Expenditure on trial run of all Tubewells including all operating / maintenance staff as per tender / DPR, chlorine and all other consumables with electricity charges till hand over the scheme to concerning ULB |
| 588 | Automation Work at ESR |
| 589 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each Tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 590 | CE/UL Certified Radar type level transmitter for OHT |
| 591 | 5200 LPM CWR at Zone- 07 |
| 592 | VT Pumping Plant |
| 593 | Supply of 2800 LPM, 34 mtr Head, (Both Tantative) 1450 RPM, SS impeller & shaft Water Lubricated VT Pump set coupled with squirrel cage VHS TEFC induction motor (Operating Voltage 415 V + 10%, 3 ph, 50 cycle) with Bowl assembly discharge head, head shaft, strainer and 4.5 mts Column Assembly to feed. (2w+1s) |
| 594 | MOTOR CONTROL PANNEL |
| 595 | SITC OF control panel having 1 Nos. incoming having 400 amp ACB draw out type & outgoing Panels ( 3 No.) 400 amp MCCB, 01 Nos 63 Amp MCCB for aux light & suitable to operated on 400 ± 6 % volt , 3 Phase , 50 Hz, AC supply Panel C.Ts, P.T AVF Meter,KWH meter P.F Meter, Bus Bar chamber, Relays and other Protective Devices Complete in all Respects. |
| 596 | Digital Soft Starter / VFD Panel 30 KW or higher Suitable to operate 300 to 500 V input Voltage. |
| 597 | Auto Phase reversal unit / Automatic switch with inbuilt the delay & enclosure (Confirms to IEC: 60947-1 & IEC: 60947-6-1)160 Amp Rating |
| 598 | MAIN PIPING AND VALVES :- |
| 599 | 200 mm dia DI sluice valve with actuator for pump |
| 600 | 200 mm dia DI sluice valve actuator for spare |
| 601 | 200 mm dia DI reflux valve |
| 602 | 300 X 200 X 300 mm size DI A/F Tee |
| 603 | 300 mm DI D/F pipe 1 mt. long |
| 604 | 300 mm DI D/F pipe 2 mt. long |
| 605 | 300 mm DI D/F pipe 1.5 mt long |
| 606 | 300 mm dia DI D/F. Bend- 90 degree |
| 607 | 300 mm size M.S. blind flange |
| 608 | 300 mm size DI Sluice Valve with Actuator (Common Header) |
| 609 | DI Reflux Valve 300 mm Size for Common Header |
| 610 | 300 x 300 x 300 mm DI Tee |
| 611 | 300 mm dia DI Sluice Valve with Actuator (for Bye pass) |
| 612 | 300 mm DI D/F pipe 1 mt. long (for Bye pass) |
| 613 | Nut bolt and rubber packing for jointing as per requirement |
| 614 | Other material such as dismantling joints, reducer inlarger as required at the time of installation |
| 615 | CE/UL Certified 300mm Size Electromagnetic Flowmeters |
| 616 | CE/UL Certified Intelligent Smart Energy Meter |
| 617 | CE/UL Certified 7\\" HMI Touch screen suitable to communication with PLC/RTU for local display and control of process parameter |
| 618 | Control panel with IP-54 protection industrial grade for all equipments seprate for control 24V and power equipments |
| 619 | Power Wiring : |
| 620 | Supply of 16 Sqmm. 3 core copper conductor cable from Starter to Motor. |
| 621 | Installation, Testing, Commissioning of VT Pumps with Power Wiring Earthing, Cable Trey including all required material for Proper installation. |
| 622 | SITC of 02 Ton, 12 mtr. Lift chain pulley Block with four way motion HOT, Gantry I-section Girder, square rod with travelling trolley. |
| 623 | Electromegnatic chlorinatimg plant of suitable capacity SCADA compatible |
| 624 | CE/UL Certified Radar type Level Transmiter for OHT |
| 625 | CE/UL Certified Radar type Level Transmiter for SUMP |
| 626 | CE/UL Certified Pressure transmitter for each pump. |
| 627 | CE/UL Certified Surge protector for control panel. |
| 628 | Rubber mat for Electrical purpose as per IS 5424. |
| 629 | Fire extinguisher ISI mark confirming to IS 15683- 4.5 Kg. |
| 630 | Internal & External electrification of Pumping plant. |
| 631 | Special Tools & Sppanners set Complete. |
| 632 | Lighting Water works Campus with Solar Panel LED light |
| 633 | Sub Station at Zone-07 |
| 634 | Supply of indoor type floor mounted metal clad, 11 KV VCB panel with 1No. 630 Amp. incoming VCB & 2 Nos 630 Amp. outgoing VCB totally enclosed & fully interlocked, horizontal drawout, horizontal/ vertical isolation type breaker as per IS with all necessory protection and also should be compatible to SCADA operation |
| 635 | Supply of 160 KVA or hieher capaccity , 11/0.44 KV, 3 Phase, 50 Hz, Dyn 11, indoor ONAN type oil cooled, copper wound transformer with Off load tap changing arrangement on HV side in steps of +7.5% & -15%, LV side @ 2.5% stapping complete with all accessories i/c first filling of filtered dehydrated oil and confirming to IS 1180-2014 (Part 1 to Part 5) & as per specification complete in all respects as required at site. |
| 636 | Supply of LT Panel comprising of following details. 02 No. 400 Amp. Incoming ACB Panel shall be mechanically and electrically interlocked completely and 01 Nos 400 Amp ACB as Outgoing and 01 Nos 63 Amp Outgoing for Auxiliary Load with motorized and microprocessor based suitable for SCADA and all necessary protection equipments and metering equipment as per requirement. |
| 637 | Supply of 70 Sq mm size XLPE cable from 11 KV UPPCL metering panel to HT incoming panel, and HT panel to both transformers. |
| 638 | Supply of 95 sq mm 3.5 core PVC insulated armored aluminum cable from transformer to LT panel. |
| 639 | Supply of HT Cable end termination joint kit. |
| 640 | Earthing system shall executed as per IS : 3043 and I.E. rules Complete in all respect e. |
| 641 | Installation and commissioning of 11 KV / 0.44 KV substation, transformers including HT panel and LT panel with cable tray including all labor T&P complete in all respect. |
| 642 | Electrification of Sub-Station (HT Room, LT Room, Metering Room & Transformer Area) |
| 643 | Rubber mat for Electrical purpose as per IS 5424. |
| 644 | Electrification of water works with Solar Panel LED light |
| 645 | NOC for substation from electrical safety department |
| 646 | Heavy duty leak proof fire bucket as per IS 2546/1974 |
| 647 | Fire bucket stand for 6 bucket |
| 648 | Fire extinguisher ISI mark confirming to IS 15683- 4.5 Kg. |
| 649 | Successful trial run till hand over the scheme to concerning ULB |
| 650 | Scada Automation Work for ZPS |
| 651 | CE&UL Certified PLC/RTU in IP54 enclosure suitable to communicate with GSM based modem unit with CPU and Power supply with analog and digital parameter and features as specified, for each tubewell /OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations as specified in tender technical specification |
| 652 | GSM/GPRS based wireless communication with 4G modem for RTU/PLC caopabke to transfer and gather data from remote sites to control stations all accessories included with signal enhancer antenna made for pumping plant internet charges as specified in the tender technical specification |
| 653 | Complete cabling for ZPS including all power and control cables of all equipments |
| 654 | Security serveillance IP camera with recorder |
| 655 | Installation, Testing and Commng of above Equipments |
| 656 | Successful trial run till hand over the scheme to concerning ULB |
| 657 | Expenditure on Trial run of CWR including all operating and maintenance staff as per tender / DPR, Chlorine & all other cunsumables, electricity charges till hand over of scheme to concerning ULB |
| 658 | SCADA DISPLAY (MCS) |
| 659 | CE/UL & BIS certified industrial grade LED Monitor with latest configuration as per specification, 65\\" |
| 660 | Desktop PC with i7 processor with one TB SSD & UPS as per specification mentioned in technical bid document |
| 661 | CE/UL certified 5 KVA UPS with batteries as per specification mentioned in technical bid document |
| 662 | Full development version of required TAGS SCADA software with customization of software for MCS as per requirement as per specification mentioned in technical bid document |
| 663 | CE/UL certified master control room PLC with redundant CPU & power supply at MCS in IP 54 encloser as per specification mentioned in technical bid document |
| 664 | CE/UL certified Field gateway agent for transferring data from MCS to Central control room |
| 665 | Desktop PC including Monitor / Laptop with i7 12th generation processor including 01 TB SSD & UPS, wireless keyboard, mouse as per specification mentioned in technical bid document for scada execution & monitoring at Jal Nigam Office. |
| 666 | GSM based wireless/ Broadband/ Equipment communication system for PLC capable to transfer & received data & gather data from remote sites to control station. All accessories included signal enhancer antenna along with running expenses till DLP |
| 667 | CE/UL Certified Firewall for network protection |
| 668 | Surge protector for Ethernet communication protection |
| 669 | CE/UL Certified industrial grade Ethernet Switch |
| 670 | Mobile App Facility system architecture (industries internet based & viewed through apps for increased local & Remote Visibility |
| 671 | Canon/HP or equivalent Laser Printer 1108 plus 02 Nos (01 Nos for mcs room & other one nos for jal nigam office) or equivalent |
| 672 | Security Surveillance IP Camera with recorder |
| 673 | Installation, commissioning and testing including required furniture, A/C, etc. |
| 674 | Successful trial run till hand over the scheme to concerning ULB Please Enable Macros to View BoQ information |