|
| 1 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, of area 3 sqm and below architrave, holdfasts etc. complete and stacking within 50 metres lead. |
| 2 | Providing and fixing factory made PVC door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm MS square tube, the vertical door frame profiles to be reinforced with 19x19 mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using MS screws of 65/ 100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge. |
| 3 | Providing and fixing 30 mm thick factory made plain panel PVC door shutter consisting of frame made out of MS tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. MS frame shall have a coat of steel primers of approved make and manufacture. MS frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the MS frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. |
| 4 | Providing and fixing float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). |
| 5 | Providing and fixing powder coated minimum thickness 50 micron aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge. |
| 6 | Providing and fixing 200x10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. |
| 7 | Providing and fixing 150x10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. |
| 8 | Providing and fixing 300x16 mm aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete. |
| 9 | Providing and fixing 100x63x3.2 mm ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. |
| 10 | Providing and fixing 125 mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. |
| 11 | Providing and fixing 100 mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. |
| 12 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete :20 mm dia |
| 13 | M&L for Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete,including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq.m, blinded with grit or pea size gravel @0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area). |
| 14 | M&L for Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources). |
| 15 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. |
| 16 | M&L for Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 17 | Dismantling tile work of thickness of tiles 10 mm to 25 mm in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 18 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 19 | M&L for Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 : 3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 20 | M&L for Non - skid joint free ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6. |
| 21 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 22 | M&L for Providing and fixing 18 mm thick Granite stone slab colour black, Cherry/Ruby red upto 0.50 sqm, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 : 4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish complete at all levels. |
| 23 | M&L for 12 mm cement plaster on brick wall of mix 1 : 6 (1 cement : 6 fine sand). |
| 24 | M&L for 12 mm cement plaster on brick wall or concrete ceiling of mix 1 : 4 (1 cement : 4 fine sand). |
| 25 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 26 | Distempering two or more coats on new work with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/ litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. |
| 27 | Dismantling 15 to 40 mm dia GI pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge. |
| 28 | Disconnecting damaged overhead/ terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge. |
| 29 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 30 | Providing and fixing 15 mm dia nominal bore GI concealed pipe complete with GI fittings and clamps, making good the walls etc., including painting with anti corrosive bitumastic paint, cutting chases and making good the wall. |
| 31 | Providing and fixing 15 mm dia nominal bore GI pipes exposed on wall complete with GI fittings and clamps, including cutting and making good the walls etc. |
| 32 | Providing and fixing 20 mm dia nominal bore GI pipes exposed on wall complete with GI fittings and clamps, including cutting and making good the walls etc. |
| 33 | Providing and fixing 25 mm dia nominal bore GI pipes exposed on wall complete with GI fittings and clamps, including cutting and making good the walls etc. |
| 34 | Providing and fixing 15 mm nominal bore CP brass long nose bib cock of approved quality conforming to IS : 8931 standards and weighing not less than 810 gms. |
| 35 | Providing and fixing 20 mm nominal bore brass stop cock of approved quality. |
| 36 | Providing and fixing 15mm nominal bore CP brass angle valve of approved quality conforming to IS : 8931. |
| 37 | Providing and fixing 15 mm nominal bore CP brass stop cock (concealed) of standard design and of approved make conforming to IS : 8931. |
| 38 | Providing and fixing PTMT Ball cock 20 mm nominal bore, 120 mm long, weighing not less than 198 gms; of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. |
| 39 | Providing and fixing white vitreous China flat back wash basin size 550x400 mm with single 15 mm CP brass pillar tap with CI brackets, 32 mm CP brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. |
| 40 | Providing and fixing 15 mm nominal bore with 45 cm length unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. |
| 41 | Providing and fixing 100 mm diameter CP brass shower rose with 15 or 20 mm inlet. |
| 42 | Providing and fixing in PTMT towel rail 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gmscomplete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 43 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with 5 litre white P.V.C. automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. |
| 44 | Dismantling 75 to 80 mm dia CI, PVC or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead. |
| 45 | Dismantling 100 mm dia CI, PVC or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead. |
| 46 | Providing and fixing on wall face unplasticised - PVC moulded 87.5° Bend 75 mm for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 47 | Providing and fixing on wall face unplasticised - PVC moulded 87.5° Bend 110 mm for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 48 | Providing and fixing white vitreous China Orissa pattern WC pan of size 580x440 mm with integral type foot rests with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls fixed in repairs. |
| 49 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete. |
| 50 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 51 | Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required Centering complete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources) |
| 52 | Thermo-mechanically treated steel reinforcement bars of grade Fe-500D or more for RCC work including straightening, cutting, bending, placing in position and binding all complete upto or above plinth level. |
| 53 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 54 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of four urinal basins with 10 litre white P.V.C.automatic flushing cistern |
| 55 | Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend. |
| 56 | Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe.Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes) |
| 57 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 58 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed. |
| 59 | Taking down Submain wiring of any size all as directed by Engineer-in-Charge. |
| 60 | Taking down TPN/SPN DBs with MCBs all as directed by Engineer-in-Charge. |
| 61 | M&L for point wiring with 1.5 sqmm multi stranded PVC insulated unseathed copper conductor cable (FRLS) in and including PVC concealed conduit 20 mm dia for one light point or fan point or bell point controlled by one modular switch 5 Amp of suitable size module including PVC insulated unsheathed 1.5 sqmm copper conductor continuous earth wire and connecting with earth dolly including with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc including necessary cutting chasing for concealing of conduit and making good the distrubed surfaces matching with existing specifications complete all as specified and directed. |
| 62 | M&L for Sub main wiring with two single core PVC insulated cable (FRLS) 2x2.5 sqmm (Nominal dia) copper conductor multistrand and drawing in and including PVC concealed conduit ISI marked, 1x2.5 sqmm multistrand copper conductor PVC green unsheathed cable for earth continuity complete all as specified and directed. |
| 63 | Supply and fixing in replacement of LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed |
| 64 | Supply and fixing in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 65 | Taking down exhaust fan of any sweep, sealing cable end, dismantling blades and removing fan from building and re-fixing after repair complete all as specified and as directed. |
| 66 | M & L in repairs of strip opening Exhaust fan, AC 230 volts,200 to 300 mm sweep any make, shifting the material to workshop for Re-winding undertaking repairs/ greasing/ oiling, replacement of unserviceable capacitor, worn out nut and bolts (chromium plated heavy duty) and cutting and getting out old burnt winding with super enameled copper winding wire of existing size including , sleeve work, varnishing with E class insulation varnishing, threading, connections with three core copper flexible wire of size 40/ 0.0076 mm of length not more than one mtr. with each fan complete all as specified and as directed. |
| 67 | S&F in replacement of ceiling rose 65 x 50mm 3 terminal AC 230 volt complete all as specified and directed |
| 68 | S&F in replacement of sheet metal enclosures for DBs when MCB to used SPN 2 way powder coated factory made with IP 43 protection, IP-09, fixed on wall /metal board/wooden board including making all incoming and outgoing connections with suitable copper lugs complete all as specified and as directed. |
| 69 | S&F in replacement of MCB SPN, 230V, 20 Amps 10 KA, 'C' series all as specified and directed. Please Enable Macros to View BoQ information |