|
| 1 | Providing one Coil Earth using No.8 GI-earth wire (50mm dia, 115 turns)including digging separate pit (0.45x0.45x1.5m) at standard distanceaway from the pole/structure in ordinary soil & backfilling. |
| 2 | Providing Stay for LT poles including digging & back filling pit inordinary soil |
| 3 | Renewal of existing damaged/broken old LT stay in existing stay rod. |
| 4 | Dismantling (without damage) one km LT three phase 4 wire OH lineconductor by dismantling cross arms, insulators and stacking theconductors in rolls properly. |
| 5 | Dismantling (without damage) one km LT additional conductor line bydismantling cross arms, insulators and stacking the conductors in rollsproperly. |
| 6 | Erecting one LT PSC Pole in position including digging & back filling pitin ordinary soil. |
| 7 | Labour charges for loading LT PSC pole from the stacking place andunloading the same at work site (transportation by any vehicle). |
| 8 | Providing Strut using LT PSC pole including digging and back filling pitin ordinary soil. |
| 9 | Dismantling (without damage) one LT PSC/RCC pole after disconnectingstays, strut etc. attached thereon and stacking the same. |
| 10 | Dismantling one damaged LT PSC/RCC pole after disconnecting stays,strut etc. attached thereon and stacking the same. |
| 11 | Transporting poles by hired vehicle to a distance upto 5km and carryingupto 4 numbers of poles excluding loading& unloading charges. |
| 12 | Transporting LT ABC by hired vehicle to a distance up to 5 km andcarring up to 2 drum including loading and un loading using crane |
| 13 | Stringing of 1.1 kV Aerial bunched cable of size 3 x 70 + 1 x 16+1x 50sqmm with bare/insulated Messenger through existing poles |
| 14 | Erection of suspension clamp for LT ABC of any size |
| 15 | Erection of Anchor clamp / dead end clamp for LT ABC of any size |
| 16 | Providing End Caps |
| 17 | Providing Cable Tie |
| 18 | Installation of Pre-insulated lugs for 16sqmm |
| 19 | Installation of Pre-insulated lugs for 50sqmm |
| 20 | Installation of Pre-insulated lugs for 70sqmm |
| 21 | Fitting one No. Section fuse on LT line with dropping cables, crimpingsockets, connecting with bolt & nut etc. |
| 22 | Installing One No. Insulation piercing connector of size Main :16 to 95,Tap:1.5 to 16 Sq.mm |
| 23 | Installation of Insulation piercing connector for main to service line main:16-95 sqmm, Tap : 4-35 sqmm |
| 24 | Installation of Insulation piercing connector for main to service line main:16-95 sqmm, Tap 16-95 sqmm |
| 25 | Installing One No. 4 way Satellite Connector of size Main :16 to 95,Tap:4 to 35 Sq.mm to the LT AB cable of Standard size |
| 26 | Disconnecting and lowering down the single phase WP serviceconnection with guy wire from the OH line and reconnecting the sameafter completing the line work. |
| 27 | Disconnecting and lowering down the three phase WP service connectionwith guy wire from the OH line and reconnecting the same aftercompleting the line work. |
| 28 | Dismantling one ordinary street light/CFL/LED fitting from existing poleand refitting the same on newly erected pole including disconnecting andreconnecting wires. |
| 29 | Dismantling (without damage) one km LT single phase 2 wire OH lineconductor by dismantling cross arms, insulators and stacking theconductors in rolls properly |
| 30 | Stringing of 1.1 kV Aerial bunched cable of size 1 x 25 + 1 x 25 sqmmwith bare/insulated Messenger through existing poles Please Enable Macros to View BoQ information |