|
| 1 | CARRIAGEMechanical transportation, loading, unloading and handling of various items such as pump parts, motors, starters, voltage stabilizers, coil assemblies, welding tools & plant, etc. using appropriate means of transport as under: |
| 2 | Private car, auto-rickshaw or similar with 1.0 km lead |
| 3 | Extra per kilometer for lead >1.0 kms upto 5.0 kms |
| 4 | Extra per kilometer for lead >5.0 kms upto 10.0 kms |
| 5 | Extra per kilometer for lead >10.0 kms upto 20.0 kms |
| 6 | Extra per kilometer for lead >20.0 kms upto 30.0 kms |
| 7 | Load carrier auto, mini van or similar with 1.0 km lead |
| 8 | Extra per kilometer for lead >1.0 kms upto 5.0 kms |
| 9 | Extra per kilometer for lead >5.0 kms upto 10.0 kms |
| 10 | Extra per kilometer for lead >10.0 kms upto 20.0 kms |
| 11 | Extra per kilometer for lead >20.0 kms upto 30.0 kms |
| 12 | Mini truck like Tata mobile, Bolero Camper or similar with 1.0 km lead |
| 13 | Extra per kilometer for lead >1.0 kms upto 5.0 kms |
| 14 | Extra per kilometer for lead >5.0 kms upto 10.0 kms |
| 15 | Extra per kilometer for lead >10.0 kms upto 20.0 kms |
| 16 | Extra per kilometer for lead >20.0 kms upto 30.0 kms |
| 17 | Truck, tipper or similar with 1.0 km lead |
| 18 | Extra per kilometer for lead >1.0 kms upto 5.0 kms |
| 19 | Extra per kilometer for lead >5.0 kms upto 10.0 kms |
| 20 | Extra per kilometer for lead >10.0 kms upto 20.0 kms |
| 21 | Extra per kilometer for lead >20.0 kms upto 30.0 kms |
| 22 | Head load carriage of machinery/ equipment at locations inaccessible by vehicles on plain/ rough terrain |
| 23 | Upto 50 kgs load |
| 24 | Extra for every additional 50kgs load (Note: Fraction >=25kgs shall be taken as equivalent to next load of 50kgs) |
| 25 | Extra for uphill terrain (Ground Slope >= 07 deg) |
| 26 | DISMANTLING AND ASSEMBLING PUMPSComplete dismantling of VT pump by way of:Disconnecting all leads from the motor and marking the terminals, uncoupling of motor from the pump, dismounting of motor with stool. Disassembling, dismantling and segregation of various pump parts such as discharge and column pipes, shafts and couplings, bowl, suction bell, impeller, stuffing box, fasteners, etc. |
| 27 | Single stage pumps with single column pipe upto 300mm ND |
| 28 | Single stage pumps with single column pipe > 300mm upto 600mm ND |
| 29 | Single stage pumps with single column pipe > 600mm ND |
| 30 | Extra per additional stage over corresponding column pipe size rates above |
| 31 | Extra per additional column pipe over corresponding column pipe size rates above |
| 32 | Complete assembling of all VT pump parts after cleaning, coupling and alignment with motor, connecting of motor leads and testing on full load. |
| 33 | Single stage pumps with single column pipe upto 300mm ND |
| 34 | Single stage pumps with single column pipe > 300mm upto 600mm ND |
| 35 | Single stage pumps with single column pipe > 600mm ND |
| 36 | Extra per additional stage over corresponding column pipe size rates above |
| 37 | Extra per additional column pipe over corresponding column pipe size rates above |
| 38 | Complete dismantling of horizontal pump (all types) by way of:Disconnecting all leads from the motor and marking the terminals, uncoupling of motor from the pump. Disassembling, dismantling and segregation of various pump parts such as shaft and sleeves, impeller, gland, fasteners, etc. |
| 39 | Suction size upto 200mm |
| 40 | Suction size > 200mm upto 400mm |
| 41 | Suction size > 400mm |
| 42 | Extra per additional stage over corresponding suction sizes above |
| 43 | Complete assembling of horizontal pump (all types) after cleaning of all parts throughly with petrol, coupling and alignment with motor, connecting of motor leads and testing on full load. |
| 44 | Suction size upto 200mm |
| 45 | Suction size > 200mm upto 400mm |
| 46 | Suction size > 400mm |
| 47 | Extra per additional stage over corresponding suction sizes above |
| 48 | Partial dismantling of VT pump by way of:Disconnecting all leads from the motor and marking the terminals, uncoupling of motor from the pump, dismounting of motor with stool. Disassembling, dismantling and segregation of various pump parts including discharge and column pipe, head and line shafts and couplings but excluding bowl assembly. |
| 49 | Pumps with single column pipe upto 300mm ND |
| 50 | Pumps with single column pipe > 300mm upto 600mm ND |
| 51 | Pumps with single column pipe > 600mm ND |
| 52 | Extra per additional column pipe over corresponding column pipe size rates above |
| 53 | Assembling of dismantled VT pump parts (excluding bowl assembly) after cleaning, coupling and alignment with motor, connecting of motor leads and testing on full load. |
| 54 | Pumps with single column pipe upto 300mm ND |
| 55 | Pumps with single column pipe > 300mm upto 600mm ND |
| 56 | Pumps with single column pipe > 600mm ND |
| 57 | Extra per additional column pipe over corresponding column pipe size rates above |
| 58 | Extraction of only stuffing box from the pump. |
| 59 | Fitting of only stuffing box to the pump. |
| 60 | Replacement of Driving End (DE) bearing of horizontal/ vertical pump by way of:Uncoupling of motor from the pump, isolating of DE bearing. Carefully extracting the old damaged bearing from the housing with the help of bearing puller, etc and fitting of new bearing in its place. Refitting back of pump parts, coupling and alignment with the pump. The job includes load testing of pump. |
| 61 | Suction size upto 200mm |
| 62 | Suction size > 200mm upto 400mm |
| 63 | Suction size > 400mm |
| 64 | Replacement of Non-Driving End (NDE) bearing of horizontal pump by way of:Opening the end cover of NDE bearing housing. Carefully extracting the old damaged bearing from the housing with the help of bearing puller, etc and fitting of new bearing in its place. Refitting back of pump parts, coupling and alignment with the pump. The job includes load testing of pump. |
| 65 | Suction size upto 200mm |
| 66 | Suction size > 200mm upto 400mm |
| 67 | Suction size > 400mm |
| 68 | Extraction of submersible pump/motor set along with column pipes from the well by hoisting with tripod and chain pulley block and by using tools and tackles required for extraction of pump set and uncoupling the pump and motor |
| 69 | Column pipes upto 100mm NB and 50mtr depth |
| 70 | For depths exceeding 50m |
| 71 | Extra over corresponding depth level for pipes >100mm NB |
| 72 | Assembling of submersible pump/ motor set and lowering along with column pipes in the well by chain pulley block, tripod, tools and tackles and testing on full load at site. |
| 73 | Column pipes upto 100mm NB and 50mtr depth |
| 74 | For depths exceeding 50m |
| 75 | Extra over corresponding depth level for pipes >100mm ND |
| 76 | Cleaning of bowl assembly components of horizontal pumping unit throughly with K-oil & wire brush for inspection of damages if any. |
| 77 | VALVESRemoval from piping system and complete dismantling of various type of valves such as foot valves/ butterfly valves/ NRVs/ check valves/ sluice valves (without spur gear mechanism) by way of disassembling of parts, etc |
| 78 | < 100mm nominal size |
| 79 | >=100mm upto 200mm nominal size |
| 80 | > 200mm upto 350mm nominal size |
| 81 | >350mm upto 600mm nominal size |
| 82 | >600mm nominal size |
| 83 | Assembling of all parts of dismantled valve, fitting in the piping system and testing. |
| 84 | < 100mm nominal size |
| 85 | >=100mm upto 200mm nominal size |
| 86 | > 200mm upto 350mm nominal size |
| 87 | >350mm upto 600mm nominal size |
| 88 | >600mm nominal size |
| 89 | Disassembling of operating mechanism of large sized valves to isolate the thrust bearing and removing it, cleaning of housing, fitting of bearing and reassembling of all parts and testing. The job is inclusive of hoisting arrangements required for execution of work. |
| 90 | Partial dismantling of various types of valves such as NRVs, sluice valves, butterfly valves, flap valves, etc. for repairs or replacement of parts such as hinge pin/ seat ring/ disc face/ hinge repairs, etc. and reassembling of all parts of dismantled valve and testing. (excluding the cost of replacement parts) |
| 91 | <100mm nominal size |
| 92 | >=100mm upto 200mm nominal size |
| 93 | >200mm upto 350mm nominal size |
| 94 | >350mm upto 600mm nominal size |
| 95 | >600mm nominal size |
| 96 | Complete removal of foot valve (all sizes) from the pump suction system and refitting and testing after carrying out the requisite works but excluding the cost of repairs/ replacements carried out on the foot valve |
| 97 | ROPE DRUM HOIST |
| 98 | Dismantling of servicable parts of pulling machine with allied drum rope hoist, shafts, couplings and gear boxes using special tools and tackles with complete cleaning and segregation of parts. |
| 99 | Fitting of all the components of the pulling machine with allied manual operation rope-drum hoisting arrangement and testing by mechanical lifting and lowering of gates, etc. |
| 100 | Extraction of bearing from standalone bearing housings/ plummer blocks, cleaning of housings and fitting of new/ old bearing, etc. |
| 101 | PUMP PARTSFabrication, providing and fitting of GM bush to bell mouth/ bowl unit/ stuffing box/ sleeve, or similar as per sample having finished weight as under: |
| 102 | Bronze bush cylindrical shell net wt. upto 1.0 kg |
| 103 | Extra per kg >1.0 kg upto 2.5 kgs |
| 104 | Extra per kg >2.5kgs upto 5.0 kgs |
| 105 | Extra per kg > 5.0 kgs (calc. at 7.5kgs) |
| 106 | Fabrication, providing and fitting of GM bush with rubber insert (Cutlass bearing) to bowl housing/ bearing retainer, etc as per sample having finished weight as under: |
| 107 | Bronze bush cylindrical shell net wt. upto 1.0 kg |
| 108 | Extra per kg >1.0 kg upto 2.5 kgs |
| 109 | Extra per kg >2.5kgs upto 5.0 kgs |
| 110 | Extra per kg > 5.0 kgs (calc. at 7.5kgs) |
| 111 | Fabrication, providing and fitting of GM lantern (cooling) ring for stuffing box as per sample having finished weight as under: |
| 112 | upto 1.0 kg |
| 113 | >1.0kgs upto 2.0 kgs |
| 114 | > 2.0 kgs (CALC AT 3KGS) |
| 115 | Providing and fitting of GM split gland as per sample having finished weight as under: |
| 116 | upto 1.0 kg |
| 117 | Extra per kg >1.0 kg upto 2.5 kgs |
| 118 | Extra per kg >2.5kgs upto 5.0 kgs |
| 119 | Extra per kg > 5.0 kgs (calc. at 7.5kgs) |
| 120 | Fabrication, turning and finishing (on inside and outside) of Stainless steel (AISI-410 or IS 1030) muff coupling, etc. as per old sample having finished weight as under: |
| 121 | upto 0.5 kg |
| 122 | upto 0.5 kg to 1 kgs |
| 123 | >1.0kgs upto 2.0 kgs |
| 124 | > 2.0 kgs (CALC AT 3KGS) |
| 125 | Fabrication, turning and finishing of specified Stainless Steel-410 shaft of specified dimensions with end preparation (threaded, etc.), keyway as per old sample having finished weight as under: |
| 126 | upto 20.0 kg |
| 127 | Extra per kg >20.0 kg upto 40 kgs |
| 128 | >40kgs upto 60 kgs |
| 129 | > 60 kgs |
| 130 | Add extra for each end on shafts with special end construction like muff coupling adapter head |
| 131 | Fabrication, turning and finishing (on inside and outside) of Stainless steel (IS 1030) shaft coupling, etc. as per old sample having finished weight as under: |
| 132 | upto 1.0 kg |
| 133 | Change)> 1.0 kg upto 3 kgs |
| 134 | > 3 kgs upto 6 kgs |
| 135 | > 6 kgs (@9kgs) |
| 136 | Fabrication, turning, finishing and fitting of Stainless steel-410 shaft sleeve as per old sample, etc. having finished weight as under: |
| 137 | upto 1.0 kg |
| 138 | > 1.0 kg upto 2.0 kgs |
| 139 | > 2kgs upto 4.0 kgs |
| 140 | > 4 kgs @6kgs |
| 141 | Manufacturing, finishing, providing of SS -410 key/ impeller lock collet as per available sample and slot size. |
| 142 | In proportion to Maharashtra DSR 2019-20 rate |
| 143 | Fabrication, turning and threading of Stainless steel shaft stud as per old sample etc. |
| 144 | Manufacturing, providing and fitting of SS (IS 1030) check nut/ impeller adjusting nut with proper locking arrangement as per sample available. |
| 145 | upto 1.0 kg |
| 146 | >1.0 kg upto 3 kgs |
| 147 | >3 kgs upto 6 kgs |
| 148 | Providing and fitting of Cast Iron split gland as per sample: |
| 149 | upto 1.0 kg |
| 150 | Extra per kg >1.0 kg upto 2.5 kgs |
| 151 | Extra per kg >2.5kgs upto 5.0 kgs |
| 152 | Extra per kg > 5.0 kgs (calc. at 7.5kgs) |
| 153 | Fabrication, providing and fitting of bronze impeller wear ring/ seal ring/ sand collar |
| 154 | upto 1.0 kg |
| 155 | Extra per kg >1.0 kg upto 2.5 kgs |
| 156 | Extra per kg >2.5kgs upto 5.0 kgs |
| 157 | Extra per kg > 5.0 kgs |
| 158 | Fabrication, providing and fitting of CI Casing ring |
| 159 | upto 1.0 kg |
| 160 | Extra per kg >1.0 kg upto 2.5 kgs |
| 161 | Extra per kg >2.5kgs upto 5.0 kgs |
| 162 | Extra per kg > 5.0 kgs (calc. at 7.5kgs) |
| 163 | Fabrication, providing and fitting of MS strainer for suction bell, etc. The strainer shall be applied with one coat of approved metal primer and two coats of anticorrosive bituminous paint to give an even shade. |
| 164 | Rethreading of bolt hole |
| 165 | upto M12 size |
| 166 | > M12 size |
| 167 | Repairs to the existing damaged SS shaft by way of rebuilding of shaft using high quality SS electrodes (Preferably: Ador/ ESAB makes) and then turning the shaft on lathe machine to remove the excess material deposited and restore the original dimensions and profile of the shaft. |
| 168 | Shaft of less than 50mm diameter at one damaged spot on shaft length |
| 169 | Extra for each subsequent damaged spot over the corresponding diameter above |
| 170 | Shaft of more than 50mm diameter at one damaged spot on shaft length |
| 171 | Extra for each subsequent damaged spot over the corresponding diameter above |
| 172 | Repairs to damaged SS shaft end by way of rebuilding using high quality SS electrodes (Preferably: Ador/ ESAB makes) and then turning the shaft on lathe machine to remove the excess material deposited. The job includes threading or collar rebuilding and facing, etc. as per requirement and restore the original dimensions and profile of the shaft. |
| 173 | Shaft of less than 50mm diameter at one damaged spot on shaft end |
| 174 | Extra for each subsequent damaged end over the corresponding diameter above |
| 175 | Shaft of more than 50mm diameter at one damaged spot on shaft end |
| 176 | Extra for each subsequent damaged end over the corresponding diameter above |
| 177 | Fabrication, providing, fitting and testing of open type impeller ( SS 304) for 70-cusec, 35-cusec, 30 cusec vertical type pumping units including carriage etc. |
| 178 | Repairs to damaged MS pump impeller by way of rebuilding the vane profile using electric arc welding and then machining to precision to get the desired profile |
| 179 | Fabrication, providing, fitting and testing of open./closed type impeller( SS 304) for vertical/horizontal type pumping including carriage etc. |
| 180 | COUPLINGSProviding and fitting flexible tyre coupling with finished bore and keyway of following designations as per IS 14285:(Note: Number in designation indicates dim. 'A' approx tyre outer dia) |
| 181 | TC-104 (TC-007) |
| 182 | TC-133 (TC-009) |
| 183 | TC 165 (TC-0012) |
| 184 | TC-197 (TC-0013) |
| 185 | TC-211 (TC-0014) |
| 186 | TC-235 (TC-0015) |
| 187 | TC-254 (TC-0016) |
| 188 | TC-279 (TC-0017) |
| 189 | TC-314 (TC-0019) |
| 190 | TC-359 (TC-0020/21) |
| 191 | TC-402 (TC-0022) |
| 192 | TC-470 (TC-0023) |
| 193 | TC-508 (TC-0024) |
| 194 | TC-562 (TC-0025) |
| 195 | TC-628 |
| 196 | Providing and fitting spare tyre for tyre coupling of following designations as per IS 14285: |
| 197 | TC-104 |
| 198 | TC-133 |
| 199 | TC 165 |
| 200 | TC-197 |
| 201 | TC-211 |
| 202 | TC-235 |
| 203 | TC-254 |
| 204 | TC-279 |
| 205 | TC-314 |
| 206 | TC-359 |
| 207 | TC-402 |
| 208 | TC-470 |
| 209 | TC-508 |
| 210 | TC-562 |
| 211 | TC-628 |
| 212 | FASTENERSProviding of high tensile steel hexagonal bolts (Dia x Length) |
| 213 | M6 x 50 |
| 214 | M8 x 80 |
| 215 | M10 x 80 |
| 216 | M12 x 80 |
| 217 | M14 x 90 |
| 218 | M16 x 100 |
| 219 | M18 x 50 |
| 220 | M18 x 120 |
| 221 | M18 x 150 |
| 222 | M20 x 100 |
| 223 | M22 x 90 |
| 224 | M22 x 120 |
| 225 | M22 x 150 |
| 226 | M24 x 90 |
| 227 | M24 x 100 |
| 228 | M24 x 150 |
| 229 | M27 x 120 |
| 230 | M30 x 110 |
| 231 | Providing of high tensile hexagonal nuts of suitable pitch with sizes as under: (Size: M Nominal Dia x Pitch) |
| 232 | M8x1.25 |
| 233 | M10x1.25 |
| 234 | M12x1.25 |
| 235 | M14x1.5 |
| 236 | M16x2 |
| 237 | M18x1.5 |
| 238 | M20x1.25 |
| 239 | M22x2.5 |
| 240 | M24x3 |
| 241 | M27x3 |
| 242 | M30x3.5 |
| 243 | Providing and fitting of carbon steel fastners of assorted sizes |
| 244 | PIPE FITTINGSFabrication, providing and fitting of SS/ alloy steel hinge pin as per old sample |
| 245 | Fabrication & providing of new bronze body seat ring/ bronze wedge facing ring/ bronze stem nut/ float guide as per sample for various valves but excluding cost of dismantling the valve parts |
| 246 | upto 1.0 kg |
| 247 | Extra per kg >1.0 kg upto 2.5 kgs |
| 248 | Extra per kg >2.5kgs upto 4.0 kgs |
| 249 | Providing and fitting of rubber gasket for various types of valves |
| 250 | Providing of jute/ hemp gland packing |
| 251 | Fabrication & providing of new SS stem nut/ stem-spindle/ pinion/ pinion shaft/ stub shaft (AISI-410 or IS 6603) for sluice/ butterfly or other type of valve as per old sample |
| 252 | upto 20.0 kg |
| 253 | Extra per kg >20.0 kg upto 40 kgs |
| 254 | Extra per kg >40kgs upto 60 kgs |
| 255 | Extra per kg > 60 kgs |
| 256 | FOOT VALVE |
| 257 | Fabrication, providing and fitting of CI disc plate as per old sample |
| 258 | Providing of leather disc face washer as per sample(Say for 4 inch dia leather washer) |
| 259 | Labour for fitting of washer to foot valve including removal of foot valve from suction line, extraction of old damaged washer, fitting of new (available) washer and refitting of foot valve to suction line. |
| 260 | Providing and fitting of C.I foot valve conforming to IS-4038 of nominal size: |
| 261 | 100mm |
| 262 | 125mm |
| 263 | 150mm |
| 264 | 200mm |
| 265 | 250mm |
| 266 | 300mm |
| 267 | 350mm |
| 268 | BALL VALVEProviding and fitting of brass ball valve (screwed) conforming to IS-778 |
| 269 | SLUICE VALVEProviding and fitting of PN 1.0 non-rising stem C.I double flanged sluice valve conforming to IS-14846 including jointing & testing with cost of jointing material such as bolts, nuts, rubber insertions etc. all complete |
| 270 | 100mm |
| 271 | 125mm |
| 272 | 150mm |
| 273 | 200mm |
| 274 | Providing and fitting of PN 1.6 non-rising stem C.I double flanged sluice valve conforming to IS-14846 including jointing & testing with cost of jointing material such as bolts, nuts, rubber insertions etc. all complete |
| 275 | 100mm |
| 276 | 125mm |
| 277 | 150mm |
| 278 | 200mm |
| 279 | REFLUX VALVEProviding and fitting of PN 1.0 (flanged) C.I reflux valve with by pass arrangement conforming to IS-5312 including jointing & testing with cost of jointing material such as bolts, nuts, rubber insertions etc. all complete |
| 280 | 100mm |
| 281 | 125mm |
| 282 | 150mm |
| 283 | 200mm |
| 284 | 250mm |
| 285 | Providing and fitting of PN 1.6 (flanged) C.I reflux valve with by pass arrangement conforming to IS-5312 including jointing & testing with cost of jointing material such as bolts, nuts, rubber insertions etc. all complete |
| 286 | 100mm |
| 287 | 125mm |
| 288 | 150mm |
| 289 | 200mm |
| 290 | 250mm |
| 291 | FLANGESProviding and welding of steel plate (MS) flanges of nominal pressure rating 1.0MPa as per IS 6392 with nominal sizes as under: |
| 292 | 100mm |
| 293 | 125mm |
| 294 | 150mm |
| 295 | 200mm |
| 296 | 250mm |
| 297 | 300mm |
| 298 | 350mm |
| 299 | 400mm |
| 300 | 450mm |
| 301 | Providing and welding of steel plate flanges of nominal pressure rating 1.6MPa as per IS 6392 with nominal sizes as under: |
| 302 | 100mm |
| 303 | 125mm |
| 304 | 150mm |
| 305 | 200mm |
| 306 | 250mm |
| 307 | 300mm |
| 308 | 350mm |
| 309 | 400mm |
| 310 | 450mm |
| 311 | Providing and fitting of steel plate blind flanges as per IS 6392 of nominal pressure rating 1.0MPa with nominal sizes as under: |
| 312 | 100mm |
| 313 | 125mm |
| 314 | 150mm |
| 315 | 200mm |
| 316 | 250mm |
| 317 | 300mm |
| 318 | 350mm |
| 319 | 400mm |
| 320 | 450mm |
| 321 | GASKETProviding of natural rubber gasket for flanged joints with nominal sizes as under: |
| 322 | 100mm |
| 323 | 125mm |
| 324 | 150mm |
| 325 | 200mm |
| 326 | 250mm |
| 327 | 300mm |
| 328 | 350mm |
| 329 | 400mm |
| 330 | 450mm |
| 331 | 500mm |
| 332 | 600mm |
| 333 | 900mm |
| 334 | PRESSURE GAUGEProviding and fitting of M.S pressure gauge as under: |
| 335 | 62mm dial |
| 336 | 100mm dial |
| 337 | 150mm dial |
| 338 | Fabrication ,Providing & fitting of MS pipe for emergent nature works such as tail piece, replacement pieces etc |
| 339 | Providing and fitting of GI pipes(B-Class) of nominal size: |
| 340 | Providing and fitting of GI Bends(B-Class) of nominal size: |
| 341 | Providing of PVC Foot valve with nominal sizes as under: |
| 342 | BEARING Supply of new bearing as under: (Make: SKF imported/ equivalent imported) |
| 343 | 3210 A/C3B4B408:B496 |
| 344 | 3212 A/C3 |
| 345 | 3213 A/C3 |
| 346 | 3309 A/C3 |
| 347 | 3313 A/C3 |
| 348 | Bearing No.51310 |
| 349 | Bearing No.51312 |
| 350 | Bearing No.51314 |
| 351 | Bearing No.51320 |
| 352 | Bearing No.6014 |
| 353 | Bearing No.6220 |
| 354 | 6314-Z |
| 355 | 6315-Z |
| 356 | Bearing No.6320 |
| 357 | 6324 (skf emarketplace) |
| 358 | Bearing No.6406 |
| 359 | Bearing No.6408 |
| 360 | Bearing No.6410 |
| 361 | Bearing No.6411 |
| 362 | Bearing No.6412 |
| 363 | Bearing No.6415 |
| 364 | Bearing No.6418 |
| 365 | Bearing No.NU322 ECJ |
| 366 | Bearing No.NU324 ECJ |
| 367 | 29322 E |
| 368 | 29324 E |
| 369 | 29328 E |
| 370 | 29330 E |
| 371 | 29424 E |
| 372 | 29426 E |
| 373 | 7316-B |
| 374 | Bearing No.6409 |
| 375 | NU 312 |
| 376 | Bearing No.6015 |
| 377 | Bearing No.6020 |
| 378 | Bearing No.6214 |
| 379 | Bearing No.NU 206 EC |
| 380 | Bearing No.6212 |
| 381 | Supply of new bearing as under: (NBC/ ARB/ ZKL/ equivalent domestic) |
| 382 | Bearing No.1217 |
| 383 | Bearing No.16026 |
| 384 | Bearing No.3200 |
| 385 | Bearing No.3210 |
| 386 | Bearing No.3212 |
| 387 | Bearing No.3213 |
| 388 | Bearing No.3214 |
| 389 | Bearing No.3215 |
| 390 | Bearing No.3306 |
| 391 | Bearing No.3307 |
| 392 | Bearing No.3309 |
| 393 | Bearing No.3310 |
| 394 | Bearing No.3311 |
| 395 | Bearing No.3312 |
| 396 | Bearing No.3313 |
| 397 | Bearing No.51310 |
| 398 | Bearing No.51312 |
| 399 | Bearing No.51314 |
| 400 | Bearing No.51320 |
| 401 | Bearing No.51322 |
| 402 | Bearing No.6014 |
| 403 | Bearing No.6028 |
| 404 | Bearing No.6217 |
| 405 | Bearing No.6220 |
| 406 | Bearing No.6305 |
| 407 | Bearing No.6306 |
| 408 | Bearing No.6307 |
| 409 | Bearing No.6308 |
| 410 | Bearing No.6309 |
| 411 | Bearing No.6310 |
| 412 | Bearing No.6311 |
| 413 | Bearing No.6312 |
| 414 | Bearing No.6313 |
| 415 | Bearing No.6314 |
| 416 | Bearing No.6315 |
| 417 | Bearing No.6317 |
| 418 | Bearing No.6320 |
| 419 | Bearing No.6322 |
| 420 | Bearing No.6406 |
| 421 | Bearing No.6408 |
| 422 | Bearing No.6410 |
| 423 | Bearing No.6411 |
| 424 | Bearing No.6412 |
| 425 | Bearing No.6415 |
| 426 | Bearing No.7214 |
| 427 | Bearing No.7220 |
| 428 | Bearing No.7308 |
| 429 | Bearing No.7312 |
| 430 | Bearing No.7314 |
| 431 | Bearing No.7319 |
| 432 | Rebuilding of bearing seats and then machining to the required size for proper fitment of bearings. |
| 433 | MISCELLANEOUS MECHANICAL WORKSProviding of steel ratchet roll/ pin |
| 434 | Casting, machining, finishing, painting and providing of CI ratchet plate as per old sample for VE motors as under: |
| 435 | upto 15kgs |
| 436 | > 15 kgs upto 30 kgs |
| 437 | > 30 kgs |
| 438 | Casting, machining, finishing, painting and providing of CI ratchet seal plate (ratchet top) as per old samples for VE motors as under: |
| 439 | > 15 kgs upto 30 kgs |
| 440 | > 15 kgs upto 30 kgs |
| 441 | > 30 kgs |
| 442 | WELDING WORKS AND ALLIED |
| 443 | Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 444 | Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 445 | Cutting charges of Mild steel pipes/ plates including cost of consumables, etc.but excluding the cost of transportation charges of equipment to site |
| 446 | Using grinder |
| 447 | By gas cutting |
| 448 | Welding charges of Mild steel sections, etc including cost of consumables, etc. but excluding the cost of transportation charges of equipment to site |
| 449 | By electric welding |
| 450 | By gas welding |
| 451 | Hiring of mobile crane |
| 452 | Hiring of excavator 3D (with driver & fuel) for earthwork excavation. |
| 453 | Providing and laying of filter media (filter gravel and sand) of specific size and grade in 5000/ 6000 GPH pressure vessel, duly washed and free from dust, dirt, loom and any other material or suspension. The job includes carriage of filter media including all loads and lifts. The media shall be laid in different layers of specific size and grade from bottom to top over the filter bed plate. The bottom layer is to be laid without tilting or damaging the pressure nozzles. |
| 454 | Providing of Grease (industrial type) conforming to IS 7623(Preferred makes: HPCL Lithon-3/ Indian oil Servogem-3/ or equivalents of BPCL; Castrol; Caltex) |
| 455 | Providing of AP3 Grease (all purpose type) IS 12203;/IS7623(Preferred makes: HPCL/ Indian oil/ BPCL/ Castrol/ Caltex) |
| 456 | Providing of circulating oil for bearing lubrication (Antiwear type)(Preferred make: Indian Oil Servosystem 57/ HPCL Enklo/ BPCL Mak) |
| 457 | Providing of transformer oil / Type II inhibited oil conforming to IS 335 (Preferred make: Power oil/ Indian Oil Servo/ HPCL) |
| 458 | Providing of graphited natural fibre (non-asbestos) packing/braided gland packing(Preferred make: Champion Style-3116 or equivalent) |
| 459 | Filtration & demoisturizing of Transformer-oil (on site) Please Enable Macros to View BoQ information |