Name of Work:- Repair/Resurfacing of factory approach roads at Main Gate, East Gate, & North gate (Road No. 55, 70, 96, & 97) at Ordnance Estate, Ambarnath | Sl. No. | Item Description | |
| 1 | Repair/Resurfacing of factory approach roads at Main Gate, East Gate, & North gate (Road No. 55, 70, 96, & 97) at Ordnance Estate, Ambarnath | | 2 | Surface dressing n exc 15 cm deep, hard dense soil | | 3 | Preparing black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms & finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. | | 4 | M & L Applying evenly a priming/tack coat with bituminous primer at 10 Kg per 10 Sq mtr using paving bitumen etc. | | 5 | M & L Premix bituminous, macadam laid/rolled and compacted to required gradient and camber | | 6 | M & L for Bituminous premix asphaltic dense concrete 25 mm consolidated thickness with 6% binder content by weight of total mix, rolled and compacted to required camber and gradient complete etc. complete. | | 7 | M&L Premixed sand seal coat with 0.06 cu.m. of sand mixed with 6.8 kg of bitumen, applied and rolled to a uniform smooth surface, paving bitumen | | 8 | S&F Reinforced concrete pipes, class NP3, laid and jointed complete with collars , 300mm | | 9 | M&L Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in 300mm | | 10 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out, hard dense soil | | 11 | M&L Cement concrete in foundations, filling and mass concrete, Type B2, 1:2:4 (40 mm graded aggregate) | | 12 | M&L Reinforced cement concrete (nominal mix) in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses, Type B1 1:2:4 (20 mm graded aggregate) | | 13 | M&L Mild steel deformed or twisted bars 6mm to 8mm, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips | | 14 | M&L Mild steel deformed or twisted bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips | | 15 | M&L Rendering 15 mm thick on wall fair faces of brick work or concrete surfaces, C:M 1:6, smooth finish | | 16 | S&F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. | | 17 | M&L preparation of New painted steel & iron surfaces of any description, over 10cm in width or girth, not otherwise described and painting with sy. enamel paint Two coat. Red oxide | | 18 | Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed | | 19 | Supply and fixing cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions. | | 20 | Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour ,T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. Please Enable Macros to View BoQ information |
|