|
Tender for Providing And Laying In Position Cment Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering- All Work Up To Plinth Level: (Dsr No. 4.1) , 1:2:4 (1 Cement: 2 Coarse Sand (Zone-Iii) Derived From Natural Sources: 4 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources) (Dsr No. 4.1.3) , 6 Mm Cement Plaster 1:3 (1 Cement : 3 Fine Sand) Finished With A Floating Coat Of Neat Cement And Thick Coat Of Lime Wash On Top Of Walls When Dry For Bearing Of Reinforced Cement Concrete Slabs And Beams (Dsr No. 13.17) , Dismantling Of Flushing Cistern Of All Types (C.I./Pvc/Victirous China) Including Stacking Of Useful Materials Near The Site And Disposal Of Unserviceable Materials Within 50 Meters Lead. (Dsr No.15.52) , Dismantling W.C. Pan Of All Sizes Including Disposal Of Dismantled Materials Including Malba All Complete As Per Directions Of Engineer-In-Charge (Dsr No. 14.82) , Providing And Fixing Grab Rail Of Stainless Steel Pipe 1-1/4 And Fitting Of Grade Aisi 304 As Per Jis Standard 3448 Including Fitting And Fixing Of Pipe With Clamps At 1.00 M Spacing Including Cutting And Making Good The Walls Complete As Per Direction Of Engineer-In-Charge. (Nsi) , Providing And Fixing Flat Pressed Three Layer Particle Or Graded Plain Wood Board Medium Density Exterior Grade (Grade I) Fpt-I, Conforming And Marked To Frame, Backing Or Studding With Screws Etc. Complete (Frames, Backing Or Studding To Be Paid Separatley. (Dsr No. 9.17) , 12 Mm Thick (Dsr No. 9.17.1) , Providing And Fixing P.V.C. Low Level Flushign Cisern With Manually Controlled Device (Handle Lever) Conforming To Is : 7231, With All Fittings And Fixtures Complete (Dsr No. 17.18) , 10 Litre Capacity - White (Dsr No. 17.81.1) , Providing And Fixing Solid Plastic Seat With Lid For Pedestal Type W.C. Pan Complete: (Dsr No. 17.20) , White Solid Plastic Seat With Lid (Dsr No. 17.20.1) , Providing And Fixing P.V.C. Waste Pipe For Sink Or Wash Basin Including P.V.C. Waste Fittings Complete. (Dsr No. 17.28) , Flexible Pipe (Dsr No. 17.28.2) , 32 Mm Dia (Dsr No. 17.28.2.1) , Providing And Fixing 600X450 Mm Beveled Edge Mirror Of Superior Glass (Of Approved Quality) Complete With 6 Mm Thick Hard Board Ground Fixed To Wooden Cleats With C.P. Brass Screws And Swashers Complete. (Dsr No. 17.31) , Providing And Fixing C.P. Brass Bib Cock Of Approved Quality Conforming To Is:8931: (Dsr No. 18.49) , 15 Mm Nominal Bore (Dsr No. 18.49.1) , Providing And Fixing C.P. Brass Long Body Bid Cock Of Approved Quality Conforming To Is Standards And Weighing Not Less Than 690 Gms. (Dsr No. 18.51) , 15 Mm Nominal Bore (Dsr No. 18.51.1) , Providing And Fixing C.P. Brass Angle Valve For Basin Mixer Ad Geyser Points Of Approved Quality Conforming To Is: 8931 (Dsr No. 18.53) , 15 Mm Nominal Bore (Dsr No. 18.53.1) , Providing And Fixing C.P. Brass Extension Nipple (Size 15 Mm X 50 Mm) Of Approved Make And Quality Make And Quality As Per Direction Of Engineer-In-Charge (Dsr No. 18.53 A) , Providing And Placing On Terrace (At All Floor Levels) Polythylene Water Storage Tank, Is : 12701 Marked, With Cover And Suitable Locking Arrangements And Making Necessary Holes For Inlet, Outlet And Overflow Pipes But Without Fittings And The Base Support For Tank.(Dsr No. 18.48) , Providing And Fixing Ptmt Pillar Cock Of Approved Quality And Colour. (Dsr No. 18.56) , 15 Mm Nominal Bore, 125 Mm Long Foam Flow, Weighing Not Less Tha 120 Gms. (Dsr No. 18.56.2) , Providing And Fixing 8 Mm Dia C.P./ S.S. Jet With Flexible Tube Upto 1 Meter Long With S..S. Triangular Plate To Eureopean Type W.C. Of Quality And Make As Approved By Engineer- In-Charge (Dsr No. 17.16A) , Providing And Fixing Uplasticised Pvc Connection Pipe With Brass Unions: (Dsr No. 18.21) , 45 Cm Length (Dsr No. 18.21.2) , 15 Mm Nominal Bore (Dsr No. 18.21.2.1) , Regarding Terracing Of Mud Phaska Covered With Tiles Or Brick, In Cement Mortar By Dismantling Tiles Or Bricks, Removing Mud Plaster, Preparing The Surface Of Mud Phaska To Proper Slope, Relaying Mud Plaster Gobri Leaping And Tiles Or Bricks, Grouted In Cement Mortar 1:3 (1 Cement: 3 Fine Sand), Including Replacing Unserviceable Tiles Or Bricks With New Ones And Disposal Of Unserviceable Material To The Dumping Ground (The Cost Of The New Tiles Or Brick Excluded), All Complete As Per Direction Of Engineer-In-Charge. (Dsr No. 14.13) , Making Khurras 45 X 45 Cm With Average Minimum Thickness Of 5 Cm Cement Concrete 1:2:4 (1 Cement: 2 Coarse Sand : 4 Graded Stone Aggregate Of 20 Mm Nominal Size) Over P.V.C. Sheet 1M X 1M X 400 Micron, Finished With 12 Mm Cement Plaster 1:3 (1 Cement : 3 Coarse Sand) And A Coat Of Neat Cement, Rounding The Edges And Making And Finishing The Outlet Complete (Dsr No. 12.22) , Providing And Fixing Led Tubelight Complete In All Respects. Make: Havells/Phillips/Usha (Nsi) , Distempering With 1St Quality Acrylic Distemper (Ready Mixed) Having Voc (Volatile Organic Compound) Content Less Than 50 Grams/ Litre, Of Approved Brand And Manufacturer Including Applying Additional Coats Wherever Required To Achieve Even Shade And Colour (Dsr No. 13.81) , Old Work (One Or More Coats (Dsr No. 13.81.1) , Finishing Walls With Acrylic Smooth Exerior Paint Of Required Shade: (Dsr No. 13.111) , Old Work (Two Or More Coat Applied @ 1.67 Ltr/ 10 Sqm) On Existing Cement Paint Surface (Dsr No. 13.111.1) , Providing And Fixing G.I. Pipes Complete With G.I. Fittings Including Trenching And Refilling Etc. (Dsr No. 18.12) , 25 Mm Dia Nominal Bore (Dsr No. 18.12.3) , Providing And Fixing Gun Metal Gate Valve C.I. Wheel Of Approved Quality (Screwed End) : (Dsr No. 18.17) , 25 Mm Nominal Bore (Dsr No. 18.17.1) , Providing And Fixing Aluminium Tower Bolts, Isi Marked, Anodised (Andic Coating Not Less Than Grade Ac 10 As Per Is : 1868) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete: (Dsr No. 9.97) , 200X10mm (Dsr No. 9.97.3) , Providing And Fixing And Installation Of Ventilation Ms Exhaust Fan 300 Mm With Frame, Nut, Bolt Etc Make Khaitan, Havells/Crompton/Gec Complete In All Respect As Per The Satisfaction Of Engineer In Charge (Nsi) , Providing And Fixing The Louvers Complete With Frame For Exhaust Fan Of 12 Diameter (Nsi) , Providing And Fixing And Installation Of Double Ball Bearing Ceilig Fan 48 Make Kahitan, Havells, Orient, Crompton Complete In All Respects As Per The Satisfaction Of Engineer-In-Charge (Nsi) , Replacement And Fixing G.I. Union In G.I. Pipe Including Cutting And Threading The Pipe And Making Long Screws Etc. Complete (New York): (Dsr No. 18.46) , 15 Mm Nominal Bore (Dsr No. 18.46.1) , Removing White Or Colour Wash By Scrapping And Sand Papering And Preparing The Surface Smooth Including Necessary Repairs To Scratches Etc. Complete (Dsr No. 13.88) , Providing And Applying White Cement Bases Putty Of Average Thickness 1 Mm, Of Approved Brand And Manufacturer, Over The Plastered Wall Surface To Prepare The Surface Even And Smooth Complete. (Dsr No. 13.80) , Providing And Fixing Water Closet Squatting Pan (Indian Type W.C. Pan) With 100 Mm Sand Cast Iron P Or S Trap, 10 Litre Low Level White P.V.C. Flushing Cistern, Includig Flush Pipe, With Manually Controlled Device (Handle Lever) Conforming To Is: 7231, With All Fittings And Fixtures Complete, Including Cutting And Making Good The Walls And Floors Wherever Required: (Nsi Based Dsr No. 17.1) , White Vitreous China Orissa Pattern W.C. Pan Of Size 580X440 Mm With Integral Type Foot Rests (Nsi Based Dsr No. 17.1.1) , Providing And Fixing White Vitreous China Pedestal Type Water Closed (European Type W.C. Pan) With Seat And Lid, 10 Litre Low Level White P.V.C. Flushing Cistern, Including Flush Pipe, With Manually Controlled Device (Handle Lever), Conforming To Is: 7231, With All Fittings And Fixtures Complete, Including Cutting And Making Good The Walls And Floors Wherever Required (Nsi Based Dsr No. 17.2) , W.C. Pan With Isi Marked White Solid Plastic Seat And Lid (Nsi Based Dsr No. 17.2.1) , Providing And Fixing Of Pvc Pipe Including Specials Labour For Fixing Treching Refilling Pvc Solvent And Testing As Per Satisfaction Of Eic (Nsi) , 2 Dia, Pvc Pipe, Make: Prince/Diplast/Supreme/Finolex (Nsi) , Providing And Fixing Pv Fitting Including Labour And Refilling Pvc Solvent And Testing As Per Satisfaction Of Eic (Nsi) , Single Tee Size 50X50x50 Mm (Nsi) , Bend 87.5 Degree Size 50 Mm Bend (Nsi) , Providing And Fixing Ptmt Grating Of Approved Quality And Colour (Dsr No. 18.58) , Circular Type (Dsr No. 18.58.1) , 125 Mm Nominal Dia With 25 Mm Waste Hole (Dsr No. 18.58..1.2) , Providing And Fixing 50 Watt Led Flood Light With Bracket Outside On The Wall Complete In All Respects (Nsi) , Wiring For Light Point/Fan Point/ Exhaust Fan Point/Call Bell Point With 1.5 Sq. Mm Frls Pvc Insulated Coppre Condctor Single Core Cable In Surface/Recessed Medium Class Pvc Conduit, With Modular Weith, Modular Plate, Suitable Gi Box And Earthing The Point With 1.5 Sq. Mm Frls Pvc Insulated Copper Counductor Single Core Cabe Etc. As Required. (Dsr Elec. No. 1.3.1) , Supplying And Fixing Following Modular Switch/Socket On The Existing Modular Plate & Switch Box Including Connections Excluding Modular Plate Etc. As Required. (Dsr Elec No. 1.24) , 15/16 A Socket Outlet (Dsr Elec No. 1.24.3) , 6 Pin 15/16 A Socket Outlet (Dsr Elec. No. 1.24.5) , Providing And Fixing In Position Pre-Cast Reinforced Cement Concrete Manhole Cover And Frame Of Required Shape And Approved Quality (Dsr No. 19.19) , Hd- 20 (Dsr No. 19.19.2) , Square Shape 450 Mm Internal Dimension (Dsr No. 19.19.2.1) , Providing And Fixing Ball Valve (Brass) Of Approved Quality, High Or Low Pressure, With Plastic Floats Complete: (Dsr No. 18.18) , 20 Mm Nominal Bore (Dsr No. 18.18.2) , Providing And Fixing Cp Flange Isi Marked 15 Mm Complete In All Respects (Nsi) , Providing And Fixing Ptmt. Push Cock Of Approved Quality And Colour (Dsr No. 18.57) , 15 Mm Nominal Bore, 98 Mm Long, Weighing Not Less Than 110 Gms. (Dsr No. 18.57.1) , Providing And Fixing Ptmt 15 Mm Urinal Spreader Size 95X69x100 Mm With 1/2 Bsp Thread And Shapes, Weighing Not Less Than 60 Gms. (Dsr No. 17.75) , Providing And Fixing Of 32 Mm C.P. Brass Waste Of Standard Pattern Complete In All Respect (Nsi) , Providing And Fixing Aluminium Work For Doors, Windows, Ventilators And Partitions With Extruded Built Up Standard Tubular Sections/Appropriate Z Sections And Other Sections Of Approved Make Conforming To Is: 733 And Is : 1285, Fixing With Dash Fasteners Of Required Dia And Size, Including Necessary Filling Up The Gaps At Junctions, I.E. At Top, Bottom, And Sides Wih Required Epdm Rubber/ Neoprene Gasket Etc. Aluminium Sections Shall Be Smooth, Rust Free, Straight, Mitred And Jointed Mechanically Wherever Required Including Cleat Angle, Aluminum Snap Beading For Glazing/ Panellig, C.P. Brass/ Stainless Steel Screws, All Complete As Per Architectural Drawings And The Directions Of Engineer-In-Charge. (Glazing, Panelling And Dash Fasteners To Be Paid For Separately) : (Dsr No. 21.1) , For Fixed Portion (Dsr No. 21.1.1) , Anodised Aluminum (Anodised Transparent Or Dyed To Required Shade According To Is: 1868, Minimum Aodic Coating Of Grade Ac 15) (Dsr No. 21.1.1.1) , Providing And Fixing White Vitreous China Flat Back Half Stall Urinal Of Size 580X380x350 Mm With White Pvc Automatic Flushing Cistern, With Fittings, Standard Size C.P. Brass Flush Pipe, Spreaders With Unions And Clamps (All In C.P. Brass) With Waste Fitting As Per Is : 2556, C.I. Trap With Outlet Grating And Other Couplings In C.P. Brass, Including Painting Of Fittings And Cutting And Making Good The Walls And Floors Wherever Required: (Dsr No. 17.5) , Single Half Stall Urinal With 5 Litre P.V.C. Automatic Flushing Cistern (Dsr No. 17.5.1) , Providing And Fixing Of Sub Boards Of Various Sizes With Remark Printing, Lamination Etc. Complete In All Respects (Nsi) , Sun Board Printing With Lamination 5 Mm Sun Bouard Size 12 X 12 (Nsi) , Sun Board Printing With Lamination 5 Mm Sun Bouard Size 12 X 18 (Nsi) , Sun Board Printing With Lamination 5 Mm Sun Bouard Size 72 X 24 (Nsi) , Removing Dry Or Oil Bound Distemper, Water Proofing Cement Paint And The Like By Scrapping, Sand Papering And Preparing The Surface Smooth Including Necessary Repairs To Scratches Etc. Complete (Dsr No. 13.91) , Providing And Fixing Sanitary Napkin Vending Machine, Incinerator, Battery And Happy Days Pad Complete In All Respects (Heavy Duty, Superior Quality, Isi Marked) (Nsi) , Note: Credit Against Old Material To Be Taken As Per Actual I.E. (I) Old Plastic @ Rs. 20/Kg (Ii) Old Ms Scrap @ Rs. 35/Kg (Iii) Old Aluminium Doors & Windows @ Rs. 200/Kg
|