Name of Work:- बांदा बबेरू कमासिन राजापुर मार्ग (राज्य सं0-92) के किमी0 4 से 12, किमी0 15 से 23(700-1000), 24 से 26 एवं किमी0 31, 32 में बी0सी0 से सामान्य मरम्मत के साथ नवीनीकरण का कार्य। | Sl. No. | Item Description | |
| 1 | Providing and applying tack coat with bitumen VG-10 bitumen pressure distributor at the rate of 0.20 kg per sum on the prepared bituminous surface cleaned with mechanical broom. As per MORT&H Clause 503 | | 2 | Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 Percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specificationclause No. 507 complete in all respects | | 3 | Earth filling in patri of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. | | 4 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 the finished surface to the level uniform and free streaks and holes. | | 5 | Supply and Fixing HAZARD MARKER (RIGHT) | | 6 | Thermoplastic Marking of 300 mm wide and 15 mm height, at 1000 mm apart (one Set is of 6 Strips). 5 mm height is achieved through two applications of thermoplastic, applied at an interval not less than 1 hour after the previous layer gets solidified. (Repeated bars) MORTH-803(8.130)-Base | | 7 | Reflective Raised Pavement Markers (Cat Eye/ Road Stud)Supply and fixing of raised pavement marker with Made of Plastic body of RPM/ Road Stud shall be moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High-Impact Polystyrene) or Acrylonitrile Butadien Styrene (ABS) or Any other suitable material approved by the Engineer. The Marker shall support a load of 13,635 kg tested in accordance with ASTM D4280.The Reflective panels shall consist of number of lenses contatning single or dual prismatic cubes capable of providing total internal reflection of the light entring the lens face. Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 or equivalent. The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro -reflecting surface shall not be less than 13.00 sq.cm. marker height shall not be less than 10 mm and shall not exceed 20 mm & Width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm all road studs shall be legibly marked with the name , trade or other means of identification of the manufacture. epoxy installations, excess adhesive around the edge of the marker, excess adhesive on the pavement and adhesive on the exposed surfaces of the markers shall be immediately removed. The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel , to the Engineer . In addition , a two year warranty for satisfactory infield performance of the finished road marker shall also be given by the contractor who carries out the work of fixing of reflective road markers. In case the markers are displaced , damaged , get worn out or lose their reflectivity compared to stipulated standards , the contractor would be required to replace all such markers within 15 days of the intimation from the Engineer , at his own cost. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge.RPM (with shank) Please Enable Macros to View BoQ information |
|