|
| 1 | Section I Building Work |
| 2 | 5.1.1Earth work in excavation in foundation trenches in ordinary soil(vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 3 | 5.1.2Extra for earth work in hard soil as per specification and direction of E/I.( vide classification of soil item B) |
| 4 | 5.1.8Filling in foundation trenches and plinth layers not exceeding 150 mm thick well watered rammed fully compacted and fine dressed with earth obtained after cutting with in a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I ( Mode of measurement compacted volume) |
| 5 | 5.1.10Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 6 | 5.6.1Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 7 | 5.3.1Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :5.3.1.31:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) |
| 8 | 5.3.9Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level.5.3.9.11:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)IN FOUNDATION |
| 9 | 5.3.17 Centering and shuttering including strutting, propping etc. and removal of form for |
| 10 | 5.3.17.1 Foundations, footings, bases of columns, etc. for mass concrete |
| 11 | 5.3.10Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 12 | 5.3.17 Centering and shuttering including strutting, propping etc. and removal of form for |
| 13 | 5.3.17.6 Columns, Pillars, Piers, Abutments, Posts and Struts |
| 14 | 5.3.10Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 15 | 5.3.17 Centering and shuttering including strutting, propping etc. and removal of form for |
| 16 | 5.3.17.6 Columns, Pillars, Piers, Abutments, Posts and Struts |
| 17 | 5.3.10Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 18 | 5.3.17 Centering and shuttering including strutting, propping etc. and removal of form for |
| 19 | 5.3.17.21 Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick |
| 20 | 5.3.11Reinforced cement concrete work in beams,Slab,lintel,etc suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 21 | 5.3.17 Centering and shuttering including strutting, propping etc. and removal of form for |
| 22 | 5.3.17.21 Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick |
| 23 | 5.3.11Reinforced cement concrete work in beams,Slab,lintel,etc suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 24 | 5.3.17 Centering and shuttering including strutting, propping etc. and removal of form for |
| 25 | 5.3.17.21 Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick |
| 26 | 5.3.11Reinforced cement concrete work in beams,Slab,lintel,etc suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 27 | 5.3.17 Centering and shuttering including strutting, propping etc. and removal of form for |
| 28 | 5.3.17.20 Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick |
| 29 | 5.3.11Reinforced cement concrete work in beams,Slab,lintel,etc suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 30 | 5.3.17 Centering and shuttering including strutting, propping etc. and removal of form for |
| 31 | 5.3.17.19 Weather shade, Chajjas, corbels etc., including edges |
| 32 | 5.3.11Reinforced cement concrete work in beams,Slab,lintel,etc suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 33 | 5.3.17 Centering and shuttering including strutting, propping etc. and removal of form for |
| 34 | 5.3.17.7 Stairs, (excluding landings) except spiral-staircases |
| 35 | 5.2.3Providing designation 75A brick work in C.M. (1:6) in foundation & plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints,cost of screening materials raking out joints to 15mm depth , curing, taxes & royalty all complete as per building specification & direction of E/I. |
| 36 | 5.3.5Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). |
| 37 | 5.2.11Providing designation 75 A BRICK WORK in CM. (1:6) in SUPERSTRUCTURE with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening,racking out joints to 15 mm depth,curing, taxes and royalty all complete as per building specification and direction of Engineer Incharge |
| 38 | 5.2.23Providing 125 mm thick REINFORCED DESIGNATION 75 A BRICK WORK in C.M. (1:4) in SUPERSTRUCTURE with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15 mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of Engineer Incharge . |
| 39 | DSR/6.15Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 40 | 5.7.3Providing 12 mm Thk. cement plaster(1:6) on inside walls with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I |
| 41 | 5.7.6Providing 6mm cement plaster(1:4) in ceiling with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I |
| 42 | 5.7.3Providing 12 mm thick water proof CEMENT PLASTER (1:6) on outside wall with clean coarse sand of F.M.1.5 and waterproofing compound (as per the manufacturers) including cost of screening, curing making grooves with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. (Cost of waterproofing compound will be paid separately) |
| 43 | 5.3.11R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 44 | 5.7.21Making 6x6mm grooves in plaster surface over walls truly horizontal vertical as specified at regular intervals at all heights including cleaning finishing scaffoding and curing with all leads and lifts of water all complete as per building specification and direction of E/I. |
| 45 | Providing tor steel T.M.T. Reinforcement FE 500 of following dia bars as per approved design and drawing including carriage of bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction and direction of E/I. (Only valid for TATA TISCON / SAIL). |
| 46 | 5.5.4Providing TMT steel reinforcement of 8 mm dia rods as per approved design and drawing excluding carriage of Rods (straight or in coils) to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position complete as per building specification and direction of E/I. |
| 47 | 10 mm dia (TMT Fe 500 (Only valid for SAIL & TATA Steel ) |
| 48 | 5.5.5 12 mm dia (TMT Fe 500 (Only valid for SAIL & TATA Steel ) 16 mm dia (TMT Fe 500 (Only valid for SAIL & TATA Steel ) 5.5.6 Providing TMT steel reinforcement of 20 mm & 25mm dia, bars as per approved design and drawing excluding carriage of M.S. Rods (straight or in coils) to work site, cutting bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/I. (TMT Fe 500 (Only valid for SAIL & TATA Steel ) |
| 49 | DSR/2.35.3.1Diluting and injecting chemical emulsion for POST-CONSTRUCTIONALanti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 50 | 5.3.8Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 51 | 5.3.13Supplying, and fixing fan hook of 16mm dia M.S. bar 1 meter long bent to required size and shape , placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. (where materials is not supplied by the deptt.) |
| 52 | 5.5.9Supplying, fitting & fixing 250 x 20 x 6 mm L-type M.S. clamp properly fishtailed including making holes and setting the same in 375 x 125 x 75 mm cement concrete block (1:2:4) with cost of all layout and materials and taxes as per building specification and direction of E/I. |
| 53 | FLOORING WORKS |
| 54 | 8.2.1.2/ D.S.R. Providing and fixing 18mm thick gang saw cut mirror polished (premoulded & prepolished) machine cut Udaipur green marble in floors of required size of approved shade, color and texture laid over 20 mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. |
| 55 | 8.2.1.1/ D.S.R. Providing and fixing 18mm thick gang saw cut mirror polished (premoulded & prepolished) machine cut Udaipur green marble in Skirting, riser of step & window cills of required size of approved shade, color and texture laid over 20 mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. |
| 56 | 11.24/ D.S.R.Extra for pre finished nosing to treads of steps of marble stone |
| 57 | 8.2.2.2/ D.S.R. Providing and laying 25mm thick Pink granite stone slab flooring of approved quality over 19mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, royalty and taxes all complete as per building specification and direction of E/I. |
| 58 | 8.2.2.1/ D.S.R.Providing and laying 25mm thick Pink granite stone slab in skirting of approved quality over 19mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, royalty and taxes all complete as per building specification and direction of E/I. |
| 59 | Area of slab upto 0.50 sq.m |
| 60 | 8.3.2/ D.S.R.Extra for providing edge moulding to Granite stone counters, vanities etc. over above including machine polishing to edge to give high gloss finish etc. complete as per design approved by Architects / E/I. |
| 61 | 11.41/ D.S.R.Providing and laying VITRIFIED FLOOR TILES in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and confirming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. (approved brand - RAK/ ASIAN/ KAJARIA) |
| 62 | 11.41.3SIZE OF TILE- 800MMX800MM |
| 63 | 11.46/ D.S.R.Providing and laying VITRIFIED TILES in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and confirming to IS : 15622, of approved make, in all colours and shades in skirting and over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.(approved brand - RAK/ ASIAN/ KAJARIA) |
| 64 | 11.46.3SIZE OF TILE- 800MMX800MM |
| 65 | 5.6.23.2Providing and laying 6 mm precast SEMI GLAZED CERAMIC TILES of approved quality in DADO over 12mm cement mortar (1:3) and jointed with white cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specification and direction of E/I with grade A coloured 20cmx15cm tiles. |
| 66 | 11.20.3 / D.S.R.Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20mm thick bed of cement mortar 1:4( 1 cement : 4 coarse sand ) |
| 67 | 16.89/ D.S.R.Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 68 | 18 mm thick crazy marble stone white, black or as specified |
| 69 | DSR/8.5Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 70 | 5.6.19(IV)Providing & laying 15 mm to 23 mm thick KOTAH STONE SLAB FLOORING and skirting of approved size, texture and colour over 19 mm thick base of line mortar (1:1:1) Lime putty: Surkhi: Coarse sand) laid over and jointed with grey cement slurry mixed with pigment ot match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 71 | 5.6.20Providing & laying 15 mm to 23 mm thick KOTAH STONE tiles in risers of steps , skirting and pillars of approved size, texture and colour over 19 mm thick base of line mortar (1:1:1) Lime putty: Surkhi: Coarse sand) laid over and jointed with grey cement slurry mixed with pigment ot match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 72 | DOORS & WINDOWS WORKS |
| 73 | 5.4.1suppling , fitting and fixing good quality well dressed and well seasoned sal wood work in chaukhat in doors window ,sky light ,fanlight and celevitial window opening including wedge over clmps all including application of two coats of wood preservative of approved quality on the surface , building walls and lintel all complete as per building specification and direction of El. |
| 74 | 5.4.41Supplying, fitting and fixing 30 mm thick solid core type non decorative double leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercially veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle cleats and blocks, and taxes all complete as per building specification and direction of E/I. |
| 75 | 9.143/ D.S.RProviding and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with |
| 76 | 9.144/ D.S.R.Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm (± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrailof size 100 mm x 37 mm, wall thickness 2 mm (+ 0.2 mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer-in-charge. |
| 77 | DSR 9.147AProviding and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. |
| 78 | After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. |
| 79 | Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. |
| 80 | Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: |
| 81 | (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 |
| 82 | (ii) Sites with structure height more than 20m for all wind speeds. |
| 83 | 9.147.A4Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. |
| 84 | 9.147.A4.1Using R2 series with frame (70mm & above) x (40mm & above) & both glazed and fly screen sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 meter). |
| 85 | 9.84/ D.S.R Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.. (Approved Brand - GODREJ/ DORSET) |
| 86 | 21.3.1/ D.S.R.Providing and fixing glazing in aluminium window, ventilator shutters etc. with EPDM / Neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): |
| 87 | With float glass panes of 4.0 mm thickness |
| 88 | 9.40.1.2/ D.S.R Providing and fixing wooden moulded beading to door frames with iron screws, plugs and priming coat on unexposed surface etc. complete. 50X20 MM |
| 89 | DSR/9.88Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.(Approved Brand - Doorset, HL CHO SC) |
| 90 | 5.5.12Supplying, fitting & fixing M.S. GRILL made of 20 x 6 mm flat as per approved design and drawing properly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I. |
| 91 | KITCHEN CABINET & ROOM CUPBOARD |
| 92 | Supplying fitting & fixing Kitchen Cabinet - 22\\"deep & 2'-6\\" height Base unit & 2'-0\\"X12\\" deep upper unit with specific stainless steel Baskets, Telescopic channel, marineply shutters & Aluminium & Wooden structure as per design and follwing detail specifications - (For 1 Kitchen) |
| 93 | 1. Stainless Steel Baskets . (Maruti Interior Products)/ Equivalent |
| 94 | a) Plain BS19206 - 2 Nos. |
| 95 | b) Cutlery BS 15204 - 1 No. |
| 96 | c) Cup Sauce Basket 15204 - 1 No. |
| 97 | d) Thali Basket 15206 - 1 No. |
| 98 | e) Plain BS 17204 - 1 No. |
| 99 | f) Plain BS 17206 - 1 No. |
| 100 | g) Plain BS 17208 - 1 No. |
| 101 | 2 . 20\\" Telescopic Channel (Fiona Make) - 8 Pair |
| 102 | 3. a)Carcase - 375X300X600 - (A&A Make) -1 No. |
| 103 | b) Carcase - 750X300X600 - (A&A Make) -2 No. |
| 104 | 4.Hinges, Handles, Glass,etc. & other Hardware as required (Vista/ equivalent) |
| 105 | 5. Marineply Shutter |
| 106 | Supplying fitting & fixing 22\\"/ 24\\" deep ROOM CUPBOARD made with 19mm th. Waterproof 3 ply commercial board (GREEN) shutters & shelves supported on 2\\"X2\\" aluminum angle screwed to the wall/ supports (board), front of shutters to be laminated with 1.5mm th. decorative matt finish with high density protective layer surface sheet (GREEN) including cost of adhesive, one drawer of 1'x5\\" size with heavy duty drawer channel 20\\" (ebbco), stainless steel hinges, 6\\" handle -2 no., 4\\" handle - 2 nos.,Tower bolt - 2 no., magnet - 3 nos. ,cupboard lock (GODREJ)-1no., Drawer lock - 1 no. (GODREJ), drawer knob, 3/4\\" dia. stainless steel pipe with socket for hanger, etc. all exposed edges covered with teak wood lipping bead and all inner sides of cupboard to be painted with 2 coats of enamel painting over a coat of primer. All Board, Laminate Sheet,Hardwares & Paints to be approved by the Architects. |
| 107 | FINISHING WORKS |
| 108 | 13.26/DSRProviding applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth copmlete . |
| 109 | 5.8.21Providing two coats of plastic emulsion paint (VOC Quality) of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I |
| 110 | 13.47.1/ D.S.R.Finishing walls with Premium Acrylic Smooth exterior paint with silicone additives \\"Snowcryl - XT\\" of M/S Snowcem India Ltd, or equivalent of required shade. |
| 111 | New work (Two or more coats applied @1.43 ltr / 10sqm. Over and including base coat of water proofing cement paint Snowcem Plus or equivalent applied @ 2.20 kg./10 sq.m. ) |
| 112 | 13.80 D.S.RProviding and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall suface to prepare the surface even amd smooth complete. |
| 113 | 13.45/ D.S.RFinishing walls with textured exterior paint of required shade : |
| 114 | 13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm |
| 115 | 5.8.42Providing Primer one coat of read lead paint of approved make over new STEEL SURFACE preparing the surface after cleaning, removing rust, dirt, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 116 | 5.8.45Providing 2 coats of SYNTHETIC ENAMEL PAINT of approved shade and make over STEEL SURFACE grills& railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I. |
| 117 | 5.8.38Providing one coats of coaltarring over wooden surface including prepatring the surface after cleaning , removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification dirction of E/I. |
| 118 | WATER PROOFING TREATMENT |
| 119 | Providing P.C.C.M - 200 with nominal mix of (1:1.5: 3) in foundation and plinth with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete, as per building specification and direction of E/I. |
| 120 | 22.5 D.S.R.Providing & laying water proofing treatment in sunken portion of WCs, abathrooms etc. by applying cement slurru mixed with Armourcrete of M/S The Structural Water Proofing Company PVT. Ltd.or Tapecrete of M/s CICO Engg. Servce consisting of applying : |
| 121 | (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with Armourcrete or Tapecrete @ 0.125 kg/ sq.m. This layer will be allowed to air cure for 4 hours |
| 122 | (b)second layer of slurry of cement @ 0.242 kg/sqm mixed with Armourcrete or Tapecrete @ 0.126 kg/ sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. |
| 123 | The rate includes preperation of surface, treatment& sealing of all joints, corners, junctions of pipes & masonary with polymer mixed slurry. |
| 124 | MISCELLANEOUS WORK |
| 125 | 12.41.2 D.S.RProviding & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socket ed pipes. 110 mm dia |
| 126 | 12.42.6.2/ D.S.R.SHOE - 110MM |
| 127 | DSR/12.42Providing & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . |
| 128 | DSR 12.42.1.2Coupler 110 MM |
| 129 | DSR 12.42.5.2110 MM Bend |
| 130 | DSR/12.43Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 131 | 12.43.2110 MM |
| 132 | 5.43/ D.S.R.Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints. |
| 133 | JSOR 2022 page no.-62 sl no. 53{M-239(ii)}Providing & supplying Cico liquid / impermo water proofing compound in cement concrete or cement mortar @ 2% of cement quqntity by weight ( as specified) for water proofing, including all carraige and taxes . |
| 134 | DSR 12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 135 | 12.45.4 Fully Perforated Gypsum Plaster Board of size 1200 x2400x12.5 mm having approx. 15 % perforated area withperforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's specification, withall 4 side tapered and backed by acoustical tissue withNRC value not less than 0.60 |
| 136 | 5.10.33Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of earthwok involved with 75mm cement concrete (1:4:3) over one brick designation 75A, flat soling in proper grade and slope at th base, he drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 137 | CARRAIGE OF MATERIALS |
| 138 | Bricks (1K+ 21P =22KM.) |
| 139 | Local Sand (3 KM) |
| 140 | Coarse Sand (16 KM.) |
| 141 | Stone Chips (32 KM.) |
| 142 | Cement (8 KM.) |
| 143 | Steel (8 KM.) |
| 144 | Earth (1K+4P=5 KM) |
| 145 | SECTION II WATER SUPPLY, DRAINAGE AND SANITARY WORKS : |
| 146 | DSR 17.1.1Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast iron P or S trap, 10 litre low level white P.V.C. Flushing cistern with munally controlled device (handle lever) conforming to IS:7231 Parryware/ Hindware with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. |
| 147 | White Vitreous China Orissa pattern W C pan of size 580 X 440 mm with integral type foot rest. |
| 148 | DSR 17.3 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flushbend, overflow arrangement with specials of standard make and mosquitoproof coupling of approved municipal design complete, including paintingof fittings and brackets, cutting and making good the walls and floors wherever required 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid |
| 149 | DSR 17.7Providing and fixing Wash basin with C.I/M.S brackets, 15mm C.P. pillar cock 32mm C.P brass waste of cutting and making good the wtherever require. |
| 150 | DSR 17.7.2.Falt back wash basin size 630X450 mm with a single 15mm C. P. pillar tap. |
| 151 | Analysed & approved Providing and fixing oval shaped counter top Wash basin with cutting and making good the whatever required al,\l complete. |
| 152 | BASIN CAT no JAQUAR CNS WHT WB 03 (With RIM TOP) |
| 153 | PILLER TAP PRS 031 JAQUAR |
| 154 | DSR 17.70.1 Providing and fixing PTMT Bottle Trap for Wash basin and sink Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms |
| 155 | DSR 18.64/ Providing and fixing PTMT/ C.P. swivelling shower,15mm nominal size, 95mm long, 65mm dia. of approved quality, color & make weighing not less than 40 gms with approximate 80 holes of 1.2 mm dia. |
| 156 | DSR17.73Providing and fixing c.p. towel rail complite with brackets fixed to wooden cleats with c.p.brass screws with concealed fitting arangement of approved qualite colour and make.(Prayag or equipment) |
| 157 | DSR 17.73.1 450mm long towel rail with total elgnth of 495 mm, 78 mm wide and effective hight of 88mm, weighin not less than 170gms. |
| 158 | DSR 17.72Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings rangement of approved quality and colour, weighing not less than 88 gms. |
| 159 | 18.49.1/ D.S.R. Providing and fixing C.P. brass bib cock of approved conforming to IS 8931 |
| 160 | 15mm nominal bore approved brand C.P. fittings |
| 161 | 18.50/ D.S.R Providing and fixing C.P.brass long body bib cock of approved quality conforming to standard and weight not less thain 810gms. |
| 162 | 15mm nominal bore approved brand C.P. fittings |
| 163 | 18.53.1/ D.S.R. Providing and fixing C.P. brass angle valve for basin mixer, gyser & others points of approved quality conforming to IS 8931 15mm nominal bore, approved brand C.P. fittings. |
| 164 | DSR 18.65Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 165 | 18.17/ D.S.R Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end ) |
| 166 | DSR 18.17.232MM nominal bore. |
| 167 | 18.18/ D.S.R. Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. |
| 168 | DSR 18.18.220mm nominal bore |
| 169 | DSR 18.18.325mm nominal bore |
| 170 | DSR 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 171 | 18.58Providing and fixing PTMT grating of approved quality and colour. |
| 172 | 18.58.2 DSR Rectangular type with openable circular lid18.58.2.1 150 mm nominal size square 100 mm diameter of the inner hinged round grating |
| 173 | DSR 17.10.2 Providing and fixing stainless steel A ISI 304(18/8) kitchen sink as per I.S.13983 with C.I. Brackets stainless steel plug 40mm including painting of fittings and brackets cutting and making goods the walls wherever required: |
| 174 | DSR 17.10.2 kitchen sink without drain board |
| 175 | DSR 17.10.2.1. - 610x510mm bowel depth 200mm |
| 176 | DSR 18.50.1 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15mm nominal bore |
| 177 | DSR 18.74.2 Providing and fixing unplasticised P.V.C. connection pipe with c.p. nuts collar and bush of approved quality. 15 mm nominal bore with 45 cm length. |
| 178 | DSR 17.22BProviding and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.(a) 15 mm nominal dia |
| 179 | Approved rate (JSR page no 40 XI )Providing and fixing Central hole Basin Mixer (Best Quality). APPROVED BRAND - JAQUAR. |
| 180 | 12.41/ DSRProviding and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (SOIL, WASTE & VENT PIPES) |
| 181 | 12.41.175 mm outer dia |
| 182 | 12.41.2110 mm outer dia |
| 183 | 12.42 D.S.RProviding & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . |
| 184 | 12.42.1DSRCoupler - |
| 185 | 12.42.1.1 DSR 75 MM |
| 186 | 12.42.1.2 DSR 110 MM |
| 187 | 12.42.2 DSRSingle pushfit Coupler |
| 188 | 12.42.2.1DSR 75 MM |
| 189 | 12.42.2.2DSR 110 MM |
| 190 | 12.42.3DSRSingle tee with door |
| 191 | 12.42.3.1DSR75X75X75 MM |
| 192 | 12.42.3.2DSR 110X110X110 MM |
| 193 | 12.42.4DSr Single tee without door |
| 194 | 12.42.4.1DSR 75X75X75 MM |
| 195 | 12.42.4.2SR110X110X110 MM |
| 196 | 12.42.5 DSRBend 87.5° |
| 197 | 12.42.5.1DSR 75 MM |
| 198 | 12.42.5.2DSR 110 MM |
| 199 | 12.42.6/ D.S.R.SHOE - 110MM |
| 200 | 12.42.6.1DSR75 MM |
| 201 | 12.42.6.2DSR 110 MM |
| 202 | 12.43/ D.S.R.Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 203 | 12.43.1DSR75 MM |
| 204 | 12.43.2DSR 110 MM |
| 205 | 18.8DSRProviding a nd fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I.(Approved Brand - ASTRAL/ SUPREME) |
| 206 | Concealed work including cutting chases and making good the wall etc.. |
| 207 | 18.8.1DSR15mm dia |
| 208 | .18.8.2DSR20mm dia |
| 209 | 18.7DSRProviding and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement & testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL) |
| 210 | Exposed on Wall |
| 211 | 18.7.3DSR25mm dia |
| 212 | 18.7.4DSR32 mm dia. |
| 213 | DSR 19.6Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete. |
| 214 | 19.6.2DSR150 MM dia R.C.C. pipe |
| 215 | 3.3.8Supllying and matarials with lobour for construction inspection chamber of designation class 75 B brick 750mm deep 600x450 internal diamention having 250mm wall thickness in cement morter(1:6) including 12mm cement plaster (1:4)with punning on inside and cement plaster (1:6)with 600x450mm C.I. cover with frame (weight not less than 36k.g)in foundation and refilling all complete as per specification and direction of E/I. |
| 216 | Analysed & Approved Providing and fixing c.p. JET SPRAY in comde with connection pipe. |
| 217 | Analysed & Approved Pvc trap including all fittings |
| 218 | D.S.R. 18.48Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 219 | SECTION III SEPTIC TANK & SOAK PIT WORKS |
| 220 | 5.1.1Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I. |
| 221 | 5.1.2Extra for earthwork in hard soil as per specification and direction of E/I. (Vide classification of soil item) |
| 222 | 5.1.10 Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume). |
| 223 | 5.6.1 Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 224 | 5.3.1Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :5.3.1.31:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) |
| 225 | 5.3.11Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 226 | 5.2.23 Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. |
| 227 | 5.3.20Providing, hoisting and fixing above plinth level up to floor five level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 228 | 5.2.2 Providing designation 75A brick work in C.M (1 : 4) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth, curring, taxes and royalty all complete as per builiding specification and direction of E/I. |
| 229 | 5.7.1 Providing 12mm thick cement plaster (1:3) with clean coarse sand of F.M. 1.5 and including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I |
| 230 | 5.7.11 Providing 1.5 mm thick cement punning including curing, carriage of water with all leads and lifts of water as per building specification and direction of E/I. |
| 231 | Basic Rate of SOR 2021 M-198 (page no 44)Providing and laying brick bats in soakpit with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. |
| 232 | Basic Rate of DW & SD SL NO 31(b) M 947Supplying, fitting and fixing C.I. cover with frame for mane hole and inspection chamber with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of E/I. (a) Size 600 x 450 mm (Wt. 25 Kg). |
| 233 | (a) Size 600 x 450 mm (Wt. 25 Kg) |
| 234 | 5.5.4 Providing Tor steel reinforcement of 8 mm dia rods as per approved design and drawing excluding carriage of bars to work site cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per builing specification and direction of E/I. |
| 235 | 8 mm dia (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 236 | 10 mm dia (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 237 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 238 | Bricks (1K+ 21P =22KM.) |
| 239 | Coarse Sand (16 KM.) |
| 240 | Stone Chips (32 KM.) |
| 241 | Cement (8 KM.) |
| 242 | Steel (8 KM.) |
| 243 | Section IV 200x150xmm dia Deep bore Well With Pump set & electrification etc works. |
| 244 | WD & SD Basic rate item no. 119 M 1035 Suppling all materisls labour and tools and cost of drilling 200mm x 165mm bore well in all kinds of soil and rock in rural area for installation of pump set with hydrolic DTH rig machine, all complete including suplying all materials tools, drilling rig, Air compressor and equipments, as well as fuel, lubricants and cost of transprtation of Rig machine and other vehicles up to the site. |
| 245 | From 0.0M to 50.0 M belew G.L |
| 246 | From 51.0 M to150.00 M belew G.L |
| 247 | DW& SD Basic rate item no. 120 M 1036supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe itc including all taxes, VAT, Excise duty, freight charges with inspection charges etc as applicable, etc all complete job. |
| 248 | WD & SD Basic rate item no. 139 M 1055Supplying 100 mm dia submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump. |
| 249 | Submersible Pump 150 mm dia ( with Bronze impeller) up to 8 stages2.0 HP |
| 250 | WD & SD Basic rate item no. 149 M 1065Supplying Fully Automatic Starter to operate induction motor working on 415v, 3 phase ,50 hz with no volt coil , Over load element , ON-OFF push buttons with necessary materials and connected to supply etc complete starter with original sheet steel encloser as per IS: 3914.F.A.S.D. Starter |
| 251 | WD & SD Basic rate item no.146 M1062Supplying 3 core flat flexible submersible cable with, copper conductor, PVC insulated and PVC sheathed as per IS : 70983 Core 4mm thick |
| 252 | WD & SD Basic rate item no. 14(K) (v)Supplying & lowering 40mm dia column G. I. pipe with all complete job. |
| 253 | SECTION V RAIN WATER HARVESTING (1 NO) |
| 254 | 5.1.1Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 255 | 5.1.2Extra for earthwork in hard soil as per specification and direction of E/I. ( Vide classification of soil iten _B) |
| 256 | 5.1.10Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 257 | 5.6.1Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 258 | 5.3.1Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :5.3.1.31:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) |
| 259 | 5.2.2 Providing designation 75A brick work in C.M (1: 4) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 260 | SOR Page 36 of Itm no M-009 & 10% CPStone Metal at quarry site .. Traxes and royalty all complete as per building specification and direction of E/I.90 mm Gravel filling |
| 261 | 0.90 M stone Boulder filling |
| 262 | 5.3.20Providing, hoisting and fixing above plinth level up to floor five level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 263 | 5.7.1Providing 12mm thick cement plaster (1:3) with clean coarse sand of F.M. 1.5 approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 264 | 5.7.6 Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scafolding taxes and royalty all complete as per buildings specification and direction of E/I. |
| 265 | 5.5.4Providing Tor steel reinforcement of 8 mm dia rods as per approved design and drawing excluding carriage of bars to work site cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per builing specification and direction of E/I. (TMT Fe 500 (Only valid for SAIL & TATA Steel ) |
| 266 | DSR 12.41.2Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 267 | DSR 12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. |
| 268 | ( 12.42.5.2) 110 mm bend |
| 269 | ( 12.42.6.2) Shoe 110 mm |
| 270 | DSR 12.43.2Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand)and making good the wall etc. complete(110 mm ) |
| 271 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 272 | Bricks (1K+ 21P =22KM.) |
| 273 | Coarse Sand (16 KM.) |
| 274 | Stone Chips (32 KM.) |
| 275 | Cement (8 KM.) |
| 276 | Steel (8 KM.) |
| 277 | SOR PHED (page no 56 M 1038) DT: Basic rate for 125/115 mm dia drilled Tube Well for drilling in all kinda of Soil and rock for installation o hand pump with DI rings all complete including supplyin all materials, labours , tools drilling rigs air compressor and equipments s well as fuel li\ubricant for making 125/115 mm dia boring etc and cost of transporting rig machine and other vechile up to site of work including contrctor profit & OH chares as per specification and directtion of Engineer Incharge(basic rate) |
| 278 | Drilling upto 30 M depth below G.L in Rular area |
| 279 | Drilling beyond 31 mtr upto 55 mtr below GL in Rural area |
| 280 | SOR PHED (page no 63 M 1041) Supplying all materials labours equipments for lowering 125 mm dia blue UPVC Casing Pipe as casing for protecting the sides from falling during the process of drilling all complete including carrriage of materials to work site (Basic Rate) |
| 281 | S/M/L for F/f wire mesh pipe |
| 282 | Section VI - APPROACH ROAD 70 Mtr leangth |
| 283 | 5.3.1Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :5.3.1.11:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 284 | 3.1Excavation in Soil by Manual means. (Excavation for foadway in soil using manual means including loading in truck for carrying of cut earth to embankment site with all lifts and lead upto 1000 metres.)(ii) Including Royalty @ Rs. 27.48 per cum the cost of watering, rolling & compaction |
| 285 | (i) Rolling with vibratory roller |
| 286 | 5.1.10Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 287 | 5.6.2Providing designation 75A one brick edge soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 288 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 289 | Bricks (1K+ 21P =22KM.) |
| 290 | Coarse Sand (16 KM.) |
| 291 | Stone Chips (32 KM.) |
| 292 | Cement (8 KM.) |
| 293 | Section VII Boundary Wall (210 metre) |
| 294 | 5.1.1 Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 295 | 5.1.2Extra for earthwork in hard soil as per specification and direction of E/I. ( Vide classification of soil iten _B) |
| 296 | 5.1.7Filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. |
| 297 | 5.1.10Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 298 | 5.6.1Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 299 | 5.3.1Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :5.3.1.31:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) |
| 300 | 5.3.9Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level.5.3.9.11:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)IN FOUNDATION |
| 301 | 5.3.17Centering and shuttering including strutting, propping etc. and removal of form for5.3.17.1Centering and shuttering including strutting, propping etc. and removal of form for |
| 302 | 5.3.10Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 303 | 5.3.17Centering and shuttering including strutting, propping etc. and removal of form for5.3.17.6Columns, Pillars, Piers, Abutments, Posts and Struts |
| 304 | 5.3.11Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 305 | 5.3.17Centering and shuttering including strutting, propping etc. and removal of form for5.3.17.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 306 | 5.2.11Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 307 | 5.7.3Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M 1.5 on inside wall including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I |
| 308 | DSR 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 309 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primerapplied @ 2.20 kg/ 10 sqm) |
| 310 | 5.5.4Providing Tor steel reinforcement of 8 mm dia rods as per approved design and drawing excluding carriage of bars to work site cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per builing specification and direction of E/I. (TMT Fe 500 (Only valid for SAIL & TATA Steel ) |
| 311 | 5.5.5 Providing Tor Steel reinforcement of 10mm , 12 mm & 16 mm dia bars as per approved design and drawing excluding carriage of bars to work site, cutting bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I |
| 312 | (a) 10 mm (TMT coil Fe 500) (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 313 | (b) 12 mm (TMT coil Fe 500) (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 314 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 315 | Bricks (1K+ 21P =22KM.) |
| 316 | Coarse Sand (16 KM.) |
| 317 | Stone Chips (32 KM.) |
| 318 | Cement (8 KM.) |
| 319 | Steel (8 KM.) |
| 320 | Section VIII Concentina Fencing |
| 321 | Material M-195 (b) (i) + 10% C.P.Supplying M.S. Angle Post 50 x 50 x 6mm Size as per building specification and direction of E/I. |
| 322 | 5.5.23Drilling 6 mm dia. holes in M.S. Angle Iron for fitting of Stable etc.as per building specification and direction of E/I. |
| 323 | 5.5.28Labour for fabricating and hoisting and fixing in position structural steel work in Rs. Joist, channel, angle,Tee ---- as per building specification and direction of E/I. |
| 324 | 5.5.24Labour for cutting M.S. Angle iron post to required length , One end splited as fish tailed in a length of 150 mm complete as per building specification and direction of E/I. |
| 325 | 5.8.45 Providing two coats of synthetic enamel paint of approved shade and made over steel surface including cleaning the surface thoroughly including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I |
| 326 | DSR 16.53 Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m) having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal including necessary bolts or G.I. barbed wire tied to angle iron all complete as per direction of Engineer-in-charge with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) |
| 327 | Section IX - Gate |
| 328 | 5.5.30Supplying, fitting anf fixing MS Grill gate with MS Grills made of 20x6mm MS flats or 16 mm MS square bars fitted on 25x25x6 mm MS Angle frame of size 60x60x6 mm including cost of fabrication , providing necesary locking arrangement with haskal and domny duly fixed in PCC (1:2:4) blocks of required size applying apriming red lead paint over steel work taxes all complete as per drawing specification and direction of E/I. (when steel is not supplied by the deptt) |
| 329 | Section X Electrical Installation work |
| 330 | Note:- OF MAKE (1)PVC insuleted copper conductor wire of make:-Havell's/Polycab/Anchor/Nitcab (2)PVC conduit of thiknss 1.5mm/2mm for wiring:-Polycab/ANCHOR/AKG (3) GI modular box of make -: Anchor/ Havells/Legrand/ABB/Anchor/ Great white (4)Switches/soket outlet for modular type:- Anchor(roma) / Havells(cabtree) / C&S/ Legrand (5)MCCB,MCB,SFU,CHANGEOVER,RCCB,MCBDB:Havell's/L&T/Legrand/Schneider/C&S/Anchor (6)XLPE/PVC aramoured cable:-Havell's/Polycab/V-guard/Finolex/Mescab (7) LED FTTING FIXTURE -: Havells/Bajaj/Crompton/C&S/Jaquar (Model/as per E/I ) (8) CEILING / WALL / EXHAUST FAN -: Havells / Bajaj / Usha/Crompton (Model/as per E/I) (9)OCTAGONAL POLE/High Mast-: Bajaj/Philips/Crompton/Surya/Valmont/Transrail (10) CENTRALISED AIR CONDITIONING-:VOLTAS/MITSHUBISHI/TOSHIBA/DAIKIN (11)ALL ELECTRICAL WIRING WORK SHOULD BE CONCEALED (12)CCTV CAMERA /DVR-:Panasonic/Hik vision/C P Plus/Godrej (13)Monitor Camera -: Dell/Samsung/LG/Asus (14)Silent type D.G Set-:Kohler/Jakson/Sterling/Eicher/Kirloskar |
| 331 | 1.3Point wiring in PVC conduit, with modular type switch:-Wiring for light point/fan point/exhaust fan point/call bell point with 1.5. sq.mm FR PVC Insuleted copper conductor single core cable in recessed PVC conduit, with modular type switch, pheonlic lamineted sheet,suitable size G.I.box etc. |
| 332 | 1.3..1Group A |
| 333 | 1.4 Twin control point wiring PVC conduit with modular type switch:-wiring for Twin control point with 1.5 sq mm FR PVC Insuleted copper conductor single core cable in recessed PVC conduit, 2 way modular, switch, pheonlic lamineted sheet,suitable size G.I.box etc.as required. |
| 334 | 1.5 Power plug wiring in PVC conduit (2x4 sq mm) :- Wiring for light/Power plug with 2x4 sq mm FR PVC insuleted copper conductor single core cable in recess PVC conduit along with 1 Nos. 4 sq mm FR PVC insuleted copper conductor single core cable for loop earthing as required. |
| 335 | 1.7 Circuit/submain wiring in PVC conduit:-Wiring for circuit/submain wiring along with earth wire with the following size PVC insuleted copper conductor single core cable in recessed PVC conduit as required |
| 336 | 1.7.2 2x2.5 sq mm+1x2.5 sq mm earth wire |
| 337 | 1.7.22x2.5 sq mm+1x2.5 sq mm earth wire(Circuit for 90 watt street light) |
| 338 | 1.7.42x6 sq mm+1x6 sq mm earth wire |
| 339 | 1.7.104x6 sq mm+2x6 sq mm earth wire |
| 340 | 1.7.114x10 sq mm+2x10 sq mm earth wire |
| 341 | 1.16 Teliphone wiring existing conduit:- Supplying and drawing following pair 0.5 sq mmFR PVC insuleted copper conductor, unaramed teliphone cable in existing recessed PVC conduit as required |
| 342 | 1.16.2 2 Pair |
| 343 | 1.17 TV cable in existing conduit :- Supplying and drawing co-axial TV cable RG-6 grade copper conductor,PE insulated,with PVC sheath in the existing recessed PVC conduit as required. |
| 344 | 1.24 S/F modular type switch /socket :- Supplying and fixing following modular type switch box/cover including connections but excluding modular plate etc as required |
| 345 | 1.24.1 5/6 amps, one way switch |
| 346 | 1.24.315/16 amps, one way switch |
| 347 | 1.24.4 5/6 amps, 3 pin socket outlet |
| 348 | 1.24.515/16 amps, 6 pin socket outlet |
| 349 | 1.24.6Teliphone socket with shutter outlet |
| 350 | 1.24.7TV socket socket outlet |
| 351 | 1.25 S/F Modular type electronic fan regulator:-Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connectionons but excluding modular plate etc, as required. |
| 352 | 1.27 S/F Modular boxes, base & covre plate:-following size/ modular G.I box along with modular base & cover plate for modular switches in recess etc, as required. |
| 353 | 1.27.1 1 or 2 module(78mm x 78mm x 45mm) |
| 354 | 1.27.24/5 module(78mm x 140mm x 50mm) |
| 355 | 1.27.3 6 module(78mm x 205mm x 50mm) |
| 356 | 1.32 S/F power plug point with modular type accessories:- Supplying and fixing suitable size G.I.box with modular plate and cover in front on recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch conection painting etc, as required. |
| 357 | 1.33 S/F ceiling rose:-Supplying and fixing 2 pin 5 amp, ceiling rose on the existing junction box/wooden block including connection etc as required. |
| 358 | 1.34S/F Batten holder:-Supplying and fixing batten/angle holder including connection etc, as required. |
| 359 | 1.37S/F Electronic musical Call bell :-Supplying and fixing electronic music call bell suitable for DC/AC single phase,230 volt, complete as required. |
| 360 | 1.41 ITC fitting fixtuure directly surface and recess:-Instaliation, testing and commissioning of prewired, fluorescent fitting of all types, complete with all accessosries and tube etc. directly on ceiling /wall including connection with 1.5 sq mm.FR PVC insulated, copper conductor. |
| 361 | 1.44 ITC ceiling/ wall fan:-Instaliation, testing and commissioning of ceiling fan including wiring the down rod of standard length( uptwo 30 cm) with 1.5 sq mm.FR PVC insulated copper conductor, single core cable etc as required |
| 362 | 1.48 ITC exhaust fan up to 450 mm, sweep:-Installation of exhaust fan up to 450 mm. sweep in the exiting opening, including making the hole to suit the size of above fan, making good the damage, connection testing commissioning etc as required. |
| 363 | 2.4 S/F MCCB in cubical panel board:-Providing and fixing following rating and capacity four pole MCCB in existing panel bord,including drilling holes in cubical panel making connections etc as required. |
| 364 | 2.4.225/100 amps, 16 KA fixed thermal setting |
| 365 | 2.4.3125 amps, 16 KA fixed thermal setting |
| 366 | 2.7 S/F, panel mounting changeoverProviding and fixing following capiacity 4 pole panel mounting chengeover switches in existing cubical panel board,making connection, earthing the body etc as required. |
| 367 | 2.7.263 amps, 4 pole |
| 368 | 2.8 S/F S.P. MCB DB:-Supplying and fixing following way single pole nutral,sheet,MCB distribution board,240 volt,in recess,complete with tinned copper busbar,earth bar, din bar, detachable gland plate, interconnections, phosphatized and power painted including earthing etc. as required.(But without MCB/RCCB/ISOLATOR) |
| 369 | 2.8.9 12 Way,Double door |
| 370 | 2.8.10 16 Way,Double door |
| 371 | 2.10S/F VERTICAL TYPE T.P.MCB DB:-Supplying and fixing following way three pole and nutral,sheet,MCB distribution board,415 volt,in recess,complete with tinned copper busbar,earth bar, din bar, detachable gland plate, interconnections, phosphatized and power painted including earthing etc. as required.(But without MCB/RCCB/ISOLATOR) Note:- Vertical type MCB TPDB is normally used where three phase outlets are required. |
| 372 | 2.10.34 way (4+12),Double door, Vertical type |
| 373 | 2.11 S/F 'B' series. S.P.MCB:-Supplying and fixing 6 amps to 32 amps rating,240 volts, 'B' series miniature circuit breaker suitable for lighting and others loads of following poles in the exiting MCB DB complite with connections. Testing and commisioning etc as required. |
| 374 | 2.11.1 6/32 amps,single pole, \\"B\\" SERIES |
| 375 | 2.11.16/32 amps,single pole, \\"B\\" SERIES(for terminal Box) |
| 376 | 2.12 S/F 'C' series. S.P.MCB:-Supplying and fixing 6 amps to 32 amps rating,240 volts, 'C' series miniature circuit breaker suitable for lighting and others loads of following poles in the exiting MCB DB complite with connections. Testing and commisioning etc as required. |
| 377 | 2.12.1 6/32 amps,single pole, \\"C\\" SERIES |
| 378 | 2.12.640 amps ,DP |
| 379 | 2.12.750/63 amps, DP |
| 380 | 2.14S/F DP MCB isoletor:-Supplying and fixing following rating double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commisioning etc as required. |
| 381 | 2.14.140 amps |
| 382 | 2.15S/F four pole MCB isoletor:-Supplying and fixing following rating four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commisioning etc as required. |
| 383 | 2.15.140 amps |
| 384 | 2.18 S/F 20 amps SPN MCB industrial socket outlet:-Supplying and fixing 20 amps, 240 volts,SPN industrial type, socket outlet, with 2 pole and and earth, metal enclosed plug top along with 20 amps 'c' series, SP MCCB, insheet steel enclosure,in recess with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. |
| 385 | 2.19 P/F M.V. danger notice plate:-Providing and fixing M.V danger notice plate of 200mm x150mm made of mild steel, at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in single red coiour on front side as required. |
| 386 | 3.2 G.I Earth pipe electrode with salt charcoal :-Earthing with G.I. earth pipe 4.5 mtr long,40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required. with salt charcoal or coke. |
| 387 | 3.7 S/L 8 SWG copper wire ground :-Supplying and laying 8 SWG copper wire 0.50 metre bellow ground level for conductor earth electrode, including soldring etc. as required. |
| 388 | 4.2 P/F G.I. lightning conductor finial:-Providing and fixing of lighting cnductor finial, made of 25 mm dia 300mm long, copper tube having single prong at top, with 85mm dia 3mm thick G.I. base plate including holes etc. complete as required. |
| 389 | 4.4 Reverting, sweating and soldering of copper/G.I. tape(with another coppr/G.I. tape, base of the finial or any other metallic object) as required. |
| 390 | 4.7 P/F G.I. lightning conductor tape in horizontal run:-Providing and fixing copper tape 20mm x 3mmthick on parapet or surface of wall for lightning conductor complete as required(For horizontal run) |
| 391 | 4.8 P/F G.I lightning conductor tape in vertical run:-Providing and fixing copper tape 20mm x 3mmthick on parapet or surface of wall for lightning conductor complete as required(for vertical run) |
| 392 | 4.12 P/F Testing joint for G.I. lighting conductor:-Providing and fixing testing joint, made of 20mm x 3mm thick G.I. strip, 125mm long, with 4 nos.of G.I. bolts, nuts, chek nuts and spring washers etc complete as required. |
| 393 | 5.2MV cable laying upto 120 sq.mm. in ground:-Laying of one number PVC insuleted and PVC sheathed/ XLPE power cable of 11 KV grade of size not exceeding 25 sq.mm.but not exceeding 120 sq.mm. direct in ground including excavetion, sand coushioning, protective covering and refilling the trench etc as required. |
| 394 | CodeS/L PVC XLPE insuletd PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts,(conforms to IS:1554, part-1) |
| 395 | M-32850 sq.mm. 3.5 core |
| 396 | M-32970 sq.mm. 3.5 core |
| 397 | DSR 12.37Supplying and fixing of light class G.I. pipe of 50 mm dia. (nominal) 3 metres length for using as a pole arm as required |
| 398 | 9.1 DSRSupplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 399 | 9.1.22 3½ X 50 sq. mm (35mm) |
| 400 | 9.1.233½ X 70 sq. mm (38mm) |
| 401 | CODE No.M-827Providing of Reces/surfaces mounted LED round down light (15/16 watt) of make bajaj/havells/crompton |
| 402 | CODE No.M-775Providing of 12'' (300 mm)exhaust fan of make bajaj/havells/usha/crompton |
| 403 | CODE M-777Providing of 16'' (400 mm)exhaust fan of make bajaj/havells/usha/crompton |
| 404 | Code no. M-856Supplying and fixing of LED 15/16 W of make bajaj/havells/crompton |
| 405 | CODE No.M-869Providing of Bulkhead fitting with 9/10 watt LED/ CFL of make bajaj/havells/crompton |
| 406 | CODE No.M-772Providing of 48'' (1200 mm) ceiling fan of make bajaj/havells/usha/crompton |
| 407 | Code no. M-854Supply of LED batten (20/22 watt) of make bajaj/havells/crompton |
| 408 | CODE No.M-848Providing of LED street light (90/100 watt) of make bajaj/havells/crompton |
| 409 | Analysed and approvedITC LED 25/ 90W street ligt on wall with 25 mm dia .75meter long GI pipe bend, J Hook 4 nos., along with two coat painting of GI pipe bend etc as required |
| 410 | Code No. M-1448Providing of Bolard fiting with cylindrical shape and inverted cone shape head, height 600 to 850 mm,8/9 watt L Brand name - BAMBOO(IP65/64 IS;10322 part 5) Havells |
| 411 | Code no. M-874Supplying and fixing of cable junction box of make sintex |
| 412 | Analysed and approvedConstructing platform of 300 mm dia 600 mm long with 300 mm depth bellow ground and rest 300 mm exposed over ground to support Bamboo Bollard with all finishing plaster putty & paint all complite as per direction of E/I |
| 413 | Add 18% GST |
| 414 | Add 1% Lebour Cess Please Enable Macros to View BoQ information |