|
| 1 | M&L for preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc sweeping with broom and and finally fanning the cleaned surface with gunny bags to remove all loose dirt/ dust etc and applying evenly a priming / tack coat with bituminous primer using paving bitumen VG 10 @ 5Kg /10 sqm complete all as specified and directed |
| 2 | M&L for 30 mm thick (consolidated thickness) Bituminous premixsemi dense asphaltic concrete with 5.50% binder content (Bituminous grade VG-30) by weight of total mix, laid by mechanical paver rolled and compacted to required camber, gradient and for uniform smoothsurface by using power roller 8 to 12 tonne capacity complete all as specified and directed. |
| 3 | M&L for Premix bituminous, macadam laid/rolled and compacted to required gradient and camber (consolidated thickness 75 mm or less) with @ 4% binder content (Bituminous grade VG-30) by weight of total mix, laid by mechanical paver, rolled and compacted with 8 to 12 tonne power roller completeall as directed and directed. |
| 4 | Supply and fixing cat eyes withtwo way solar reflective type with 30 mm length double shank of plasticbody of size 100mm x 110mm x 20mm(overall height 50 mm) and with PAMA striplens reflector and weight 164 gramfixed with special epoxy chemical as per manufactures instructions. |
| 5 | Supply and fixing aluminium-alloy body Solar stud with following specification :-(a)Solar panel Mono-Crystalline Solar 2.4V/0.3 Watt and having charging capacity at a very low sunlight.(b)Red colour Six Super Bright LEDs with 10000 to 18000 mcd (Millicandela) 8 mm fitted at appropriate height for clear blinking point.(c) 1.2V Ni-MH or Ni-CD rechargeable battery capacity 1300 mAh.LSD (Low Self Discharge technology) fitted inside solar stud.(d)Working time 3 to 4 days successively after the battery is fully charged.(e)Charging time for full charge One full sunny day.(f)Working temperature : 10 to 75 Degree Celcius.(g)Flash rate : 60 to 70 times per minute normally.(h)Brightness sensitive auto-switch, automatically turns on at dusk and turns off at dawn to ensure easy and safe night driving.(j) High visibility LEDs help ensure easy andand safe night driving from a distance of 1000-1100 Meters approx.(k)Solar stud should be free of maintenance and operational in all weather conditions.(i)The PCB board and solar panel should be sealed in Poly Carbonate case for extra waterproofing and high/low temperature protection.The logo of the manufacturer should be embossed on front side of the body to ensure genuinesess.Dimension/Size of the Solar Std should be 125 mmx125mmx25 mm body, with shank height 65 mm (Total height 90 mm including shank)(m)Weight of the Solar Stud should be 650 Gram approx.(n)Minimum 150 gram of a special epoxy chemical should be used per pcs to fix the stud on the road surface. |
| 6 | Providing and applying 2.5 mm thick road marking strips n exc 15 cm width with 250 gram Glass Beads(retroreflective) of specified shade/colour using hot thermoplastic material by fully/semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoes heater, driven by experoenced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dier, seals, oil, grease and foreign material etc, complete as per direction and accordance with applicable specifidactions as per MoRTH specification having Titatnium -12%, Resin-19% & Intermix Glass Beads - 34 % in proportion. |
| 7 | Providing and applying 2.5 mm thick road marking strips exceeding 15 Cm widthwith 250 gram Glass Beads(retroreflective) of specified shade/colour using hot thermoplastic material by fully/semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoes heater, driven by experoenced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dier, seals, oil, grease and foreign material etc, complete as per direction and accordance with applicable specifidactions as per MoRTH specification having Titatnium -12%, Resin-19% & Intermix Glass Beads - 34 % in proportion. |
| 8 | M&L for WBM 150mm compacted thickness in two layers (each 7.5 cm thick) with coarse aggregates (Granite, trap or Basalt) of grading 2 (63 mm to 40 mm size), spread, rolled and consolidated to gradient and camber complete all as specified and directed. |
| 9 | Rolling and consolidation of formation surfaces with power roller exc 8 tonne & n.exc 12 tonne complete all as specified and directed. |
| 10 | M&L for continuous brick edging, with width equal to the width of the brick, laid dry on end vertically with burnt clay bricks of sub class B old size bricks incl demolition of existing brick edging complete all as specified and directed. |
| 11 | M&L for Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400 sqm exceeding 50mm deep and not exceeding 100mm deep complete all as specified and directed. |
| 12 | M&L for 40 mm thick (consolidated thickness) Bituminous premixsemi dense asphaltic concrete with 6.0% binder content (Bituminous grade VG-30) by weight of total mix, laid by mechanical paver rolled and compacted to required camber, gradient and for uniform smoothsurface by using power roller 8 to 12 tonne capacity complete all as specified and directed. |
| 13 | S & F one 3-seater outdoor garden bench matching the design and quality of the reference picture.The bench must have a heavy-duty cast iron frame with rust resistant coating and seat/back support made using a minimum of 8 FRP (Fibre Reinforced Plastic) wooden finish strip suitable for outdoor use. The bench shall be measure approximately 125-140 cm in length, 40-50 cm seat height from ground, and 45-55 depth. The total weight of the bench must be between 50kg to ensure to durability and stability and all fastening hardware shall be stainless steel or equivalent corrosion - resistant material. The bench must be weather proof, Water proof, UV resistant and free from sharp edges, structural defects, cracks,rust or visible manufacturing flaws at the time delivery complete all as specified and directed by Engr-In-Charge. |
| 14 | Supply and Fixing in repair solar integral AIO Post -top luminaire with solid polycarbonate housing, reliable & robust construction with IP65 protection, suitable for pole entry dia of 60mm, having Min3000 system lumens suitable for 12 hours (Dim mode) Autonomy lightining mode selectable for 2H/4H/6Halong with the CCT 3000K/4000K/6500K by remote.Lithium Pherrophosphate Battery capacity min 14.4 Ah @ 3.2V.Panel capacity min 13 Wp, CRI>=70, system Efficacy > 165Lm/W & system wattage should not be more than 18W+ 2%, if wattages increases then the size of battery& panel shall also be increased in similar percentage to maintain equal autonomy of the system.Microwave Motion Sensor 5.8GHz<=25mW. Life class of LED System 25000hrs @ L70 LED.CE Certified, charger efficiency>90%.The PV module should be made up of crystalline silicon solar cells \"Mono-Crystalline\" and must have a certificate of testing concirming to IEC 61215 Edition-II/BIS 14286 & IEC 61370-1,2 IEC 60598, Operating temp 0 degree centigrate to 55 degree Centigrate, certifying above given parameters all reports shall be from in house NABL or IECQ or any international accredited Laboratory including fixing of polewith nut and bolt and bolt grout with PCC column size 45cm x 45cm x 50cm complete all as specified and directed by Engr-In-Charge. |
| 15 | M&L for preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc sweeping with broom and and finally fanning the cleaned surface with gunny bags to remove all loose dirt/ dust etc and applying evenly a priming / tack coat with bituminous primer using paving bitumen VG 10 @ 10Kg /10 sqm complete all as specified and directed. |