|
| 1 | Demolition of brick work built in CM including all quions, arches, pillars etc complete all as specified and directed. |
| 2 | M & L for Brickwork with fly ash bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed. |
| 3 | M & Lfor brick work with fly ash bricks straight or curved on plan exc 6m mean radius in half brick thick walls built in CM 1:4 complete all as specified and directed. |
| 4 | (a) Taking down cement plaster and clean the floor or wall surface for treatment by removing dust, dirt and loose particles over the surface etc by mechanical means.(b) Providing and applying the water based silicon water repellent. It shall be mixed with water in brick work or concrete surfaces in 1:10 ratio or as per manufacturer\"s instruction.(c) Providing and applying one coat of modified cementitious bonding agent / water proofing coating treatment over the treated area of water repellent mixed with 1 part of cement and 1 part of Latex SBR/Bond SBR.(d) Providing & laying polymer, water proofing compound & fiber based ready mix plaster for rendering 15 mm thick in CMon brick walls, finished even & smooth without using extra cement complete as per manufacturer\"s instructions. |
| 5 | (a) Taking down cement plaster and clean the floor or wall surface for treatment by removing dust, dirt and loose particles over the surface etc by mechanical means.(b) Providing and applying the water based silicon water repellent. It shall be mixed with water in brick work or concrete surfaces in 1:10 ratio or as per manufacturer\"s instruction.(c) Providing and applying one coat of modified cementitious bonding agent / water proofing coating treatment over the treated area of water repellent mixed with 1 part of cement and 1 part of Latex SBR/Bond SBR.(d) Providing & laying polymer, water proofing compound & fiber based ready mix plaster for rendering 10-12 mm thick on brick walls, finished even & smooth without using extra cement complete as per manufacturer\"s instructions. |
| 6 | M & L for 5mm thick rendering in CM (1:3 ) on ceiling finished even and fair including taking down cement plaster from brick wall including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. |
| 7 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and removing serviceable tiles to store yard and rubbish off the primises as directed. |
| 8 | M &Lfor Non skid ceramic coloured floor tiles shade as approved andsize300 x 300mm x 7mm thick set on 15mm thick in screed bed in cement mortar (1:6) and pointed in neat cement slurry including jointing with white or colour cement to match complete all as specified and directed. |
| 9 | M & L for glazed ceramiccolourtiles of size300 x450mm x 7mm thick on walls etc, set & jointed in neat cement slurry and pointed in white or colours cement tomatch the colour of tilesas in skirting/dados over and including 10mm thick backing coat in CM 1:4 all as specified and directed. |
| 10 | Roughening surfaces of old concrete floor by picking, sweeping clean, washing down with water to remove dust etc including Brushing neat cement slurry with 3.0kg of cement per sq. metre |
| 11 | M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchincluding 15mm thick screed bed in cement & sand mortar 1:4, complete all as specified and as directed. |
| 12 | M & L for 20mm thick granite stone slab as in cooking platform,window cill over 15mm thick screed bed in CM 1:4 including cutting, polishing & rubbing and including rounding of exposed edges complete all as specified and direceted. |
| 13 | M & L for drilling through holes in granite stone for pipes etc not exc. 25 mm diaall as specified. |
| 14 | Demolition of RCC as in lintel, shelves etcnexc 15 cm thickness (below or above ground level) |
| 15 | M & L for RCC 1:2:4, type B1 using 20mm graded stone aggregatein RCC lintel, shelves, hold fast etc. with necessary form work complete all as specified and directed. |
| 16 | M & L for Mild steel TMT bars 10mm dia and over as in reinforcement,cut to length, bent to shape required includinghooking ends and binding with MS wire (annealed) not less than 0.9 mm dia all as directed and specified. |
| 17 | Taking down steel tubing and connections and fittings 15mm bore includingcleaning for refixing or removing from site complete all as specified and direceted. |
| 18 | Taking down steel tubing and connections and fittings 20mm bore includingcleaning for refixing or removing from site complete all as specified and direceted. |
| 19 | M & L for GI tubing 15mm dia, medium grade, galvanised with all fittingsfixed to wall and floor all as specified. |
| 20 | M & L for GI tubing 20mm dia, medium grade, galvanised with all fittingsfixed to wall and floor all as specified. |
| 21 | M & L for cutting and chasing in brick wall built in cement mortar for concealed GI tubing and making good in CM, 1:3 not exc 10cm in girth. |
| 22 | Taking down eaves Guttersrain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc, including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and direceted. |
| 23 | S & FPVC (SWR) Pipes 110mm dia single socketed in any length with rubber ring joints , fixed towalls complete all as specified and direceted. |
| 24 | S & F 75mm PVC SWR pipes single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed. |
| 25 | S & F PVC (SWR) bendsany radius 110mm dia. |
| 26 | S & F PVC (SWR) single TEE equal 110mm dia. |
| 27 | S & FPVC (SWR) bendsany radius 75mm dia. |
| 28 | S & F in repair 75mm dia PVC Floor trap incl grating fixed in floor with cement complete all as specified and directed. |
| 29 | S & F in repairs vitreous china ware wash hand basin, white, flat back, size 550 mm x 400 with full pedestal including cutting for and pinning ends of brackets and fixed on a pair of CI cantilever bracket of appropriate size, including S & F of 15mm size single lever CP basin mixer, with 450mm long braided connection pipe, 32 mm dia PTMT waste pipe & waste coupling, complete all as specified and directed. |
| 30 | S & F in repairs vitreous china squatting pan of “Orissa” pattern of size 580mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to disturbed floor as per existing including removing of debris from site (At a place as directed), complete all as specified and as directed. |
| 31 | S & F in repairs vitreous china wash down water closet pan P or S trap (pedestal pattern) white excluding flushing cistern & flush pipe with and including recessed bottom PVC seat cover (same colour of WC pan) etc complete, and connection to drain or outgoing pipe, antisyphonage pipe, complete all as specified and directed. |
| 32 | S & F in repairs chromium plated wall mixer 3-in-1 system with provision of and including both telephonic hand shower 1.5m long hose and overhead shower 125mm dia including overhead shower arm with wall flange complete with and including 115mm long bend pipe and wall flange including jointing to concealed GI / steel pipes or unions and plugging and screwing to walls, complete all as specified and as directed. |
| 33 | S & F in repairs 15 mm bore bib taps, chromium plated, long shank with wall flange, fancy type, cast copper alloy with any type handle handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed. |
| 34 | S & F in repairs 15 mm bore angle stop cock, cast copper alloy, fancy type, chromium plated,screwed down high pressure screwed one ends for iron pipes or for union complete all as specified and directed. |
| 35 | S & F in repairs 15 mm bore stop valve cast copper alloy, fancy type, chromium plated with long shank and cup (Concealed type),screwed down high pressure without or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed. |
| 36 | S & F in repairs brass chromium plated shower rose with or without swivel joints 125 mm size including fixing to iron pipes or union, complete all as specified and directed. |
| 37 | S & F in repair CP brass soap dish fancy type of one soap fixed with screw to wall as directed. |
| 38 | S & F in repairPVC flushing cistern 10 Ltrs capacity including all fitting flush pipe etc complete all as specified |
| 39 | S & F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 40 | S & Fin repairCP Brass toilet paper holder with wall hook bracket etc, complete set of superior quality. |
| 41 | S & Fin repair 15mm bore PVC connection 450mm long with brass/PVC coupling and washer as directed. |
| 42 | S & F in repairs brass chromium plated tubular towel rail 20 mm dia D type, 60 cm long between flanges complete all as specified and as directed. |
| 43 | S & F in repair600x450mm beveled edges mirror of selected quality glass mounted on 4mm thick MDF board or plywood fixed to wall with rawal plug and CP screws complete all as specified. |
| 44 | S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 600 mm long. |
| 45 | S & F in repair glass corner shelves fancy type 6mm thick 250x250mm size and fixed over CP brass brackets all as specified and directed. |
| 46 | S & F in repair stainless peg sets consisting 06 Nos of pegs of approved quality complete all as specified and as directed. |
| 47 | S & F in repair sink with drainage board size 1145x510 mm, bowl size 560x410x200 mm made of stainless steel sheet 1.00mm thick with plugs, washers and wastes pipe & coupling etc incl bedding in cementmortar to draft wall or cantilever brackets and connection union to pipe all as specified and directed. |
| 48 | S & F in repair stainless steel kitchen plate rack made out of 1.00 mm thick stainless steel sheet of size 900 X 750 X 250 mm includingscrews and weight not less than 5.00 Kg complete all as directed. |
| 49 | S & F in repair rotantional moulded polythylene water storage tanks 500 ltr capacity(cylindrical vertical with closedtop ) hoisted and fixed in position all as specified in SSR part-I complete all as specified and directed. |
| 50 | S & Fin repair rotantional moulded polythylene water storage tanks 1000 ltr capacity(cylindrical vertical with closedtop ) hoisted and fixed in position all as specified in SSRpart-I complete all as specified and directed. |
| 51 | S & F ball valves high perssure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed 20 mm bore, complete all as specified and directed. |
| 52 | S & F in repair Gun-metal, globe or gate valves 20mm with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. |
| 53 | S & F in repair Gun-metal, globe or gate valves 15mm with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. |
| 54 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) n.exc 1.50 Sqm and removing from sites directed. |
| 55 | All as item No 55 above but exc 1.5 Sqm but n.exc 4 Sqm Each. |
| 56 | Supply and fixing Solid PVC Double Door Frame of size 50mm x 95mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawingcomplete all as specified and directed. |
| 57 | Supply and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed. |
| 58 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 59 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 60 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture roof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 61 | S & F30mm thick factory made solid WPC (Wood Polymer Composite) moulded gauged door shutter with wire mesh in any no of division with brown wood grain texture including SS wiremesh (G-304) 0.36mm minimum dia of wireand average width of aperture 1.40mm shall be fixed with 15 X 15 square tube in side rails with screwing 8 X 28 heat metal zinc coated screws can be removed or fixed again after changing of wire mesh when needed. The density shall be as per manufacturer\"s instruction complete all as specified and as directed. |
| 62 | S & F Mild steel framed work such as grills, grating, framed guard bars and similar work conforming to Fe 290 Gde E -165 complete all as specified and directed. |
| 63 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note:1. Glazed shutters float glass thickness not less than 5.00 mm and wiremesh shutters with stainless steel (SS 304) wiremesh 0.36 mm dia with aperture 1.4 mm shall also be deemed included in quoted rates and no extra payment will bemade separately.2. For UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 64 | S & F Aluminium Butt hinges, 100mm sizecomplete all as specified and directed. |
| 65 | S & F 200mm long alumunium anodised barrel tower bolts of extructed section complete all as directed and directed. |
| 66 | S & F alumunium handle, fabricated type, anodised 150 mm longcomplete all as specified and directed. |
| 67 | S & F of mild steel sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. |
| 68 | S & F Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed 140 MM Overall length of cover plate. |
| 69 | S & F Factory made WPC single extruded 100% lead free ISO certified board of 18mm thick both side prelaminated shutter for Kitchen cupboard, room cupboard and bathroom cupboard. The laminated shutter should be 12-14 microne pre-laminated side with color and other side same laminated color of density not less than 650 kg/ cum manufactured by an ISO 9001:2015 certified company. All the edges shall be covered with 2 mm thick edge moulding tape or 90 degree edge bend finish. The 18 mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity complete all as specified and directed. |
| 70 | S & F Continuous (piano) hinges width of flange (whene open) 30mm mild steel, bright finish or elecrogalvanised fixed with screw to timber frame work complete all as spacified and directed. |
| 71 | S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed. |
| 72 | S & F magnet catcher heavy duty for cupboard shuttercomplete allas specified and directed. |
| 73 | S & F of hasp and staple 100mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws all as specified and directed. |
| 74 | S & F 8 to 10 mm dia anchor fastner of length exc 75 mm but n. exc 150 long including drilling holes in concrete/masonary walls/ stucture using electrically operated drill machine compete all as specified and directed at site.Note-Rate quoted includes cost of one 3 mm thick GI washer and one hexagonal GI nut per bolt. |
| 75 | S & F in repair fancy type 25mm dia stainless steel curtain rods/Cupboard hanging rods including bracket/junctions /wall to wall and with rings of best quality as approved by Engineer-in-Charge. |
| 76 | S & F stainless steel wire cloth 0.36mm dia of wire and average width of aperture 1.4mm fixed with stanless steel staples or steel/wooden beadings towindows complete all as specified and directed. |
| 77 | S & F 300 mm MS ordinary rat tail pattern spring including roller & roller plate complete as directed. |
| 78 | M & L for preparation of new surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over a coat of 1mm thick Birla white wall care putty on wall (two or more coats) complete all as specified and directed. |
| 79 | M & L for complete removal of existing treatment of old surface of wall and and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over a coat of 1mm thick Birla white wall care putty on wall (two or more coats) complete all as specified and directed. |
| 80 | M & L for preparation of newplastered surface of wall and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and incl Priming plastered and other surfaces with alkaliresistant priming paintcomplete over a coat of 1mm thick Birla white wall care putty on wall (two or more coats) , as per manufacturer\"s specification, complete all as specified and directed. |
| 81 | M & L for complete removal of existing treatment of old surface of wall and applying distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. includingover and incl Priming plastered and other surfaces with alkali resistant priming paint over a coat of 1mm thick Birla white wall care putty on wall (two or more coats) complete, complete all as specified and directed. |
| 82 | M & L forfor preparation of new plastered ceiling surface and applyingthreecoats ofwhite wash completeall as specified and directed. |
| 83 | M & L for preparation of old treated ceiling surface and applying twocoats ofwhitewash completeall as specified and directed. |
| 84 | M & Lfor preparation of new wood or wood based surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 85 | M & L preparation of new steel surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer all as specified. |
| 86 | M & L for preparation of old treated steel surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint all as specified. |
| 87 | Demolition of Cement concrete (unreinforced) in ground floor and paving not exc 15cm thicknes below or above ground level complete all as specified directed |
| 88 | M & L for preparation of surface of wall/chajja and applying a coat of tapecrete P-151/Cemcrete acrylic polymer modified cementitious slurry consisting of one part of TAPECRETE P-151, two parts of cement by weight complete all as specified and directed. |
| 89 | M & L for PCC 1:5:10, type E-2 using 40 mm graded stone aggregate as foundation filling and mass concrete in sunken floor etc. complete all as specified and directed. |
| 90 | M & L for PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregate as in leveling course,padding of any thickness etc. complete all as specified and directed. |
| 91 | M & L for plain cement concrete type C-1 (1:3:6) using 20mm graded stone aggregate for embedding of holdfasts etc complete all as specified and directed. |
| 92 | M & L for PCC 1:2:4, type B-1 using 20mm graded stone aggregate as in benching & coping etc complete all as specified and directed. |
| 93 | M & L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as psecified. |
| 94 | M & L for 10mm thick rendering on fair faces of brickwork or concrete surface in CM (1:3 ) includingfinished even and smooth (without using extra lime or cement) using 100% coarse sand on roof surface including WPC as per manufacturer\"s instructions complete all as specified and directed. |
| 95 | M & L for provision of rooftreatment using polymeric water proofing membarane including taking down existing treatment and removal of waste materials all as given below:-(a)Taking down existing water proofing treatment and removal of waste material retrieved to a distance nexc. 500m where directed.(b) M & L for Applying a coat ofbituminous primer to IS : 3384 -1986 @ 0.25 Ltrs/Sqm and allowed to dry.(c) M & L for applying hot bitumen 85/25 @ 1.20 Kg/sqm over primer as directed.(d)M & L for Laying 3mm thick APP membrane having non oven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides withoverlaps 100mm and 150mm at longitudinal and transverse direction respectivelyand sealed by flame,sealing all overlaps complete including treatment at all junctions and corners.The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3.(e) M & L for two coats of Aluminium paint on membrane surface allas specified and directed. |
| 96 | Cutting holes in brick walls built in cement mortar or cement lime mortar to a depth measured from the face of jamb exceeding half brick but not exceeding one brick and making good dismantled portion in CM 1:3 or cement concrete 1:2:4 type B1 as required for fixing purlins,rafters etc. |
| 97 | S & F steel tubular section Fe-290 (Gde E-165) as in beams ,rafters,purlins and running rails and guide for sliding doors fixed with MS cleats or other connecting plates including cutting, grinding, welding etc as required complete all as specified and directed. |
| 98 | S & F 0.50 mm thick pre-painted galvalume aluminium zinc coating galvanised iron based corrugated steel sheet with side lap and end lap of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 99 | M & L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as inplinth protection surface finished fair and even without using etra cement complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).Complete all as specified and directed. |
| 100 | (a)Taking down plaster and Clean the floor suface & wall for treatment by removing dust , dirt and loose particles over the surface etc by mechanical means.(b)Providing & applying the Water based silicon water replient and injection system confirm IS 2645-2003with solid content 35% and lilica content 18% . It shall be mixed with wateras per suface like Concrete surface 1:10and brick / block work. 1:10 as per manufacturer\"s specifications.(c)Providing & Applying one coat of modified Cementitious bonding agent / waterproofing coatiing treatement over the treated area of water repellent mixed with 1 part cement and 1 part Latex SBR/Bond SBR.(d) Providing with an laying waterproof plaster of average 15-20mm thick to the walls mixed cement mortar (1:4) admixed with an integral waterproofing compound confirm to IS 2645 @ 200 mll 50 Kg cement as per manufasturer\"s specifications. |
| 101 | (a)Taking down plaster and Clean the floor suface & wall for treatment by removing dust , dirt and loose particles over the surface etc by mechanical means.(b)Providing & applying the Water based silicon water replient and injection system confirm IS 2645-2003with solid content 35% and lilica content 18% . It shall be mixed with wateras per suface like Concrete surface 1:10and brick / block work. 1:10 as per manufacturer\"s specifications.(c)Providing & Applying one coat of modified Cementitious bonding agent / waterproofing coatiing treatement over the treated area of water repellent mixed with 1 part cement and 1 part Latex SBR/Bond SBR.(d) Providing with an laying waterproof plaster of average 15-20mm thick to the walls mixed cement mortar (1:6) admixed with an integral waterproofing compound confirm to IS 2645 @ 200 mll 50 Kg cement as per manufasturer\"s specifications. |
| 102 | Taking down carefullycopper/aluminium point wiring (light, fan, socket or power) complete with fitting such asswitches, sockets ceiling rose sketch light fittings etc, and making good the disturbed surface ofwalls and floors etc as directed. |
| 103 | M&L, Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No.in and including medium grade PVC concealed conduit and conduit accessories concealed in wall etc,ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes(with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sqmm nominal cross sectional area single core F.R.L.S. cable as earth continuity conductor to common earth and connecting to earth dollycomplete all as specified and directed for one light / fan point controlled by one switch with cable size 1.5 sqmmat site for the following:-NOTE:-(I) Switch and socket to be measured and paid for separately.(II) PVC Open Conduit on Ceiling surface for Ceiling fan will be provided by the contractor as per site requirement. |
| 104 | All as per Serial item No. 103 here in before but One 3 Pin, 6 Amp socket outlet point on an independent board with cable size 1.5 sqmm. |
| 105 | All as per srl item No. 103 here-in-before but one 3 pin socket outlet 06 Apms point on the same board with other switches with cable 1.5 Sq mm size. |
| 106 | All as per srl item No 103 here-in-before but one bell / buzzer point controlled by one bell push button on the same board with other switches or independent with cable 1.5 Sq mm size. |
| 107 | All as per Serial item No. 103 here in before but One 3 pin, 16 Amp socket outlet point on an independent board with cable size 2.5 sqmm. |
| 108 | Supply and fixing switch piano flush type, single pole, one way, 06 Amps complete all as specified and directed by Engr-in-charge. |
| 109 | Supply and fixing switch piano flush type, single pole, one way, 16 Amps complete all as specified and directed by Engr-in-charge. |
| 110 | S&F socket outlet flush type multipurpose 2 in1, 3 pin 6 and 16 Amp, 230 volts complete as directed. |
| 111 | S&F socket outlet flush type 3 pin 6 Amps 240 volts complete as directed. |
| 112 | S&F ceiling rose surface bakelitethree terminal complete as directed. |
| 113 | S&F bell push single pole one way 5 Amp, 240 volt fueshtype as directed. |
| 114 | S&F angle type holder insulated body with back plate suitable for batten fittings as directed. |
| 115 | Supply & fixing LED bulb 9 watt complete all as specified and directed . |
| 116 | S&F call bell AC single pole 240 volt Musical Typecomplete all as specified and directed . |
| 117 | Supply & fix fan regulator electronic step type for ceiling fan fixed, in existing board and connecting as directed, after dismantling and removing unserviceable regulator. |
| 118 | S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way 240 Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, IK09, True IP 43 (with PU Gasket) with test certificate factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed. |
| 119 | S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 8 way 240 Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated,IK09, True IP 43 (with PU Gasket) with test certificatefactory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed. |
| 120 | S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 4 way 240 Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, IK09, True IP 43 (with PU Gasket) with test certificate factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed. |
| 121 | S&F Modular AC BOX Power unit with Socket Plug top and MCBs with Single pole and neutral enclosure with a two pin and one pin for earth plug and socket complete with one single pole MCB 25 Amp complete all as specified and directed by Engr-in-charge. |
| 122 | Supply and fixing of MCB SP 240 volts of 06 to 32 Amps, 10 KA Current carraying capacitycomplete all as specified and directed by Engr-in-charge. |
| 123 | Supply and fixing of MCB SPN 240 volts of 40 Amps, 10 KA Current carraying capacity complete all as specified and directed by Engr-in-charge. |
| 124 | M&L in replacement for Submain wiring with two single core unsheathed, PVC (FRLSH) insulated, 1100 Volts grade cable with 4.0 sqmm nominal cross sectional area Multi-stranded copper conductor and one single core green unsheathed, PVC (FRLSH) insulated, 1100 Volts grade cable with 4.0 sqmm Multi-stranded copper conductor earth continuity cable drawn through non metallic rigid PVC conduit 25 mm dia including all conduit and fixing accessories concealed in wall including cutting chases in wall and making good disturbed surface to match of walls/ceilingcomplete all as specified and directed by Engr-in-charge. (Note - PVC Conduit and accessories shall be deemed to be included in the quoted rate) |
| 125 | M&L in replacement for Submain wiring with two single core unsheathed, PVC (FRLSH) insulated, 1100 Volts grade cable with 6.0 sqmm nominal cross sectional area Multi-stranded copper conductor and one single core green unsheathed, PVC (FRLSH) insulated, 1100 Volts grade cable with 6.0 sqmm Multi-stranded copper conductor earth continuity cable drawn through non metallic rigid PVC conduit 25 mm dia including all conduit and fixing accessories concealed in wall including cutting chases in wall and making good disturbed surface to match of walls/ceilingcomplete all as specified and directed by Engr-in-charge. (Note - PVC Conduit and accessories shall be deemed to be included in the quoted rate) |
| 126 | Supply and Fixing wall/surface mountingluminaires integrated LED Batten 20/22 W, 6500 K,100 lumens/watt , 230V with extruded Aluminium housing4 feet long with frosted PMMA/PC diffuser & integrated electronic driver, 25k burning hours ,2.5 KV surge protectioncomplete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangementsall as per specified and directed by Engr-in-charge. |
| 127 | Supply and fixing wall/surface mounting luminaires (Mirror Light) integrated LED Batten( 2 feet) 10/12 W, 6500 K, 230V , minimum 100 lumens/watt,with extruded aluminium housing & integrated electronic driver completeincluding Electrical connection with PVC three core copper flexible wire & all necessary fixing arrngementsall as per specified and directed by Engr-in-charge. |
| 128 | S& Fin repairDecorative wall light fixturemade up of Metal base, synthetic white in colour and square/round metal base with bend pipe and glass globe with nickel finish,( B-22/E27 base), with 01 No. 12 W LED Bulb, 230 V, 6000K, complete incl all required electrical connecting arrangements all as specified and as directed. |
| 129 | S&F in repair LED Building security light 20/25 Watt with high power LED source (>100 lumen/watt) PDC housing, IP66 and IK 07with 4 KV inbuilt surge protection ,minimum 50000 burning hours hv cutoff@325/440 volt protection for 8 hoursincluding Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories , as specified and directed by Engr-in-charge. |
| 130 | Supply and fix in replacement of integrated LED bulk head fitting 10 Watt, 6500K with IP 65 protection comprises of high pressure die cast aluminium housing, polycarbonate cover, etc complete all as specified and directed. |
| 131 | M&L Taking down carefully ceiling fan of any sweep complete with all accessories, dismantling blades and deposit in safe custody of AGE E/M Yard for BER procedure complete all as specified & directedby Engr-in-charge. |
| 132 | M&L for Taking down existing electric energy meter and refixing after rewiring work complete all as specified and directed . |
| 133 | Supply & fix Exhaust fans, plastic body, AC, single phase, 230/240 V of size 250 mm sweep with louver including provn of flexible three core cable from ceiling rose to terminal for making connection, fitting on wall, including Cutting, opening circular/Rectangular in shape hole on wall for fixing of exhaust fan of size 250 mm sweep incl plastering and making good the disturbed surface surrounding and all necessary fixing accessories complate all as specified and asdirected . |
| 134 | S&F BLDC ceiling fan 1200 mm sweep, 350 RPM with 100 % Copper winding silent BLDC motor, Powder coated Rust Proof Body & Blades, Min air delivery 220 CMM, Power consumption 26 - 28 watt, BEE 5 Star rating, White in colour with down rod as per site requirement alongwith connected accessories incl provn of connection with three core flexible copper wire cable of size 1.50sqmm from ceiling rose to fan, Min 2 years procuct warranty and 05 years motor warranty complete all as specified and directed by Engr-in-charge.Note:- Old Ceiling fan shall be deposited in AGE E/M yard for BER procedure. |
| 135 | S&F in replacement of Storage type Water heater/Geyser of 25 Ltrs capacity, electric BEE five star ratedto operate on 230 volt AC supply, Vertical type, white in colour, working pressure Min 08 bar with Marine Grade Glasline Coating tank, magnesium anode, adjustable thermostat, efficient long-life copper heating element 2 KW, Shock resistance & Rustproof ABS plastic body, Child safety Mode, incl Fire retardant cable with 16 Amp plug top with Product warranty 2 years, Heating element warranty 4 years, Inner Tank warranty -7 years, including 2/4 Nos full threaded fastnar of size 100 x 10 mm with nuts and 2 Nos washer complete all as specified and directed by Engr-in-charge.NOTE: Old geyser shall be deposited at E/M store yard for BER Procedure. |
| 136 | M &L Earthing complete with galvanised steel earth plate electrode60cm X 60 cm X 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level with the top edge of electrode not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4mm dia means of bolts, nuts,check nuts and washers of galvanised iron and GI lead protected with protection pipe of GI light grade 15mm dia upto 3mtr above ground level along poles fixed with two clamps of 25mm 3mm flat iron and connected to running earth wire at top of poles and watering pipe 20mm bore of GI medium grade all as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthing test point all as specified and direct and testing on completion including PCC 1:3:6 ) C-I cover and frame excavation and earth work etc complete all as specified in elect plate No 3 of SSR Part -I 2009 Note :- PCC Chamber shall be constructed at least 1.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner. |
| 137 | Dismantling carefully electric Chimney with exhaust pipe and refixing Same on new board after rewiringin replacement of unservicable wire complete all as specified and directed by Engr-in-charge. |