Tender For Special Repair To Mt Complex And Roof Of Certain Buildings At 24 Ed; M & L preparation of roof treatment with APP polymeric water proofing membrane allgiven as under complete all as specified and directed.:- (a) Taking down existing water proofing treatment/brick tiles and cleaning roof surface by washing and rubbing etc and removing retrieved material to a distance not exceedingeeding 500mcomplete all as specified and directed. (b) M & L for plastering 10mm thick in CM 1 : 3 using 100% coarse sand on roof surface including water proofing compound as per manufacturers instructions complete all as specified and directed. (c) Applying a coat of bituminous primer conforming to IS : 3384 - 1986 @ 0.30 Kg/Sqm and allow to dry. (d)M & L for laying 3mm thick APP modified polymeric water proofing membrane having weight 3.2 - 3.5 Kg/Sqm on prepared surface as per manufacturers instructions and over laps 10 cm and 15 cm longitudinal and traverse directions respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners.The membrane shall be torched into groove on verticle plane and grove sealed with cement mortar 1:3.complete all as specified and directed. (e) Applying two coats aluminium paint 0.2 Kg/sqm all as per specification and complete all as specified and directed. , Dismantling of brick tiles or terracing tiles single layer bedded in cement mortar on roof& disposal of retrieved material upto a distance n. exceeding. 100m where directed complete all as specified. , Demolition of Mud in roofs, any thickness, including plastering and leeping ( where full thickness recovered or only a part there of disposal of rubbish/ demolisedmaterials upto a ditance exceedin 500 m but not exceeding 1.5Km away and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed Note: Demolised material should not be thrown away on the ground from the top of roof, it should be removed from the roof by manually or by any mechanical means. complete all as specified and diected. , Taking down existing water proofing treatment and cleaning roof surface by washing and rubbing etc and removing retrieved material to a distance not exceeding 500m complete all as specified and diected. , M&L for cutting out cracks to V-section in existing roofs or terracing, cleaning out wetting, grouting with cement and sand slurry 1:3complete all as specified and diected. , M&L for PCC1:2:4 type B-0 using 12.5mm graded stone aggregate , as in roof curving, padding,coping with mixing of WPCetc complete all as specified and directed by Engr-in-charge. Note:-Water Proofing compound shall bemeasured and paidseparatly. , M & L for plastering 10mm thick in CM 1:3 using 100% coarse sand on roof surface mixed with water proofing compound @ 200ml per bag of cement or as per manufacturers instructions and as directed by Engr-in-Charge Note:-Water Proofing compound shall bemeasured and paidseparatly. , Supplying and applying high build elastomeric water proofing coating based on pure, hydrophobic polyurethane, cold applied spray/brush applied , smart care PU magnum membrane with and elongation of 450% and tensile strengh of 2.5 N/Sq mm as per ASTM D 2370, crack bridging ability of 3mm as per ASTM C 1305, no leakage upto 7 bars of water pressure as per DIN 1048,shore a hardness of min.45 as per ASTM D2240.The system includes final base preparation , epoxy primer application andapplying smart care PU magnum or approved equavalent in two coats with a consumption of 1.5 Kg / Sqm on a primed surface with smart care primer and a 40GSM geo textile cloth sandwiched in between etc., complete all as per manufacturer specification complete all as specified and directed by Engr-in-charge. , supply only liquid water proofing compound (ISI marked) complete all as specified and directed. , M&L for 15mm thick rendering in CM (1:3) on edges of RCC chajja or corners of columns where steel reinforcement coming out after fixing 15mm size wire netting of mild steel wire 1.60 mm dia fixed with tinned tacks of wire staples including taking down of plaster complete all as specified and directed. , M & L brushing neat cement slurry with 3.0kg of cement per sq. metrecomplete all as specified and directed by Eng-in-Charge. , Taking down cement plaster or cement lime plaster on brick ,conc. Surfaces or stone walls or over roof etc.Including raking out joints ,hacking for key, scrubbing down with water etc complete all as specified and directed. , M & L rendering 15 mm thick in cement plaster 1 : 4on fair faces of brick wk or concrete surface finishing the surface even and smooth without using extra cement complete all as specified and directed. , M&L for preparing new suface and applying two coats of cement based paint over a coat of primer complete all as specified and directed. , M & L preparation& treatment ofExpansion/Crumple Joint all as given below :- (a) Taking down existingExpansion/Crumple Joint, water proofing treatment, brick tiles and cleaning joint surface by washing and rubbing etc and removing retrieved material to a distance not exceedingeeding 500m where directed. (b) M & L for plastering 10mm thick in CM 1 : 3 using 100% coarse sand at surface of expsansion/crumple joint including water proofing compound as per manufacturers instructions and as directed by Engr-in-Charge. (c) Placing the required dia of baker rods inside the joint before applying the sealant. (d) Applying and filling the joint with Fosroc thioflex 600(pourable grade) two part polysulphide sealant upto required level. , M&L preprationof surface and applying a coat of bituminous primer conforming to IS : 3384 - 1986 @ 0.30 Kg/Sqm and allow to dry,laying of 3mm thick APP modified polymeric water proofing membrane having weight 3.2 - 3.5 Kg/Sqm on prepared surface as per manufacturers instructions and over laps 10 cm and 15 cm longitudinal and traverse directions respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on verticle plane and grove sealed with cement mortar 1:3.complete and applying two coats aluminium paint 0.2 Kg/sqm all as per specificationcomplete all as specified and directed. , Demolition of reinforced cement concrete in any description and thickness complete all as specified and directed by Engr-in-Charge. , M&L for RCC 1:2:4 type B-1 nominal mix using 20 mm graded stone aggregate as in slab, coping, cover etc complete all as specified and directed. , Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs,shelve, landings and similar work; not exceedingeeding 200mm thick (Horizontal or sloping ,) finishing the surface fair&finished surfacecomplete all as specified and directed. , M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. , M&L TMT bars 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for stirrups,spacers & binders binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. , Supply & Fixing 75mmx75mm mesh size and3.4 mm dia of wire chain link MS galvanised fencing complete including line wires, rails, straining bolts etc, including provision of binding wire includingdismantling chain link fencing any type complete all as specified and directed. , Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground in natural ground complete all as specified and directed. , Excavating in post holes or similar holes for posts or struts each not exceeding 0.5 Cum, getting out, and removing surplus soil to a distance not exceeding 50min soft/loose soil complete all as specified and directed. , S & F Rolled Mild Steel Framed work as in doors or Gates, grills,fencing post, support on wall of angle or other section confirming to Fe 410 -W (Gde-, E- 250) A quality-with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering and hanging and fixing complete all as specified and directed. , M&L for PCC1:3:6 type C-2 using 40mm graded stone aggregate,asin foundation filling & mass concrete etc complete all as specified and directed. , M&L in applying two coats of synthetic enamel paints over a coat of red oxideprimer on new steel surfaces over 10 cm width or girth including preparatinon of surfaces complete all as specified and directed. , S&F galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and provision of galvanised clips etc including dismantling/Removing of existing barbed wire/razor wire of any descreption/pattern complete all as specified and directed. Note: Each line of wire measured. , Demolition of cement concrete (unreinforced) in ground floors and pavings not exceedingeeding 15cm thickness complete all as specified and directed by Engr-in-Charge. , M&L PCC1:4:8 type D-2 using 40mm graded stone aggregate,including necessary formwork and finishing the surface of cone ,even & rough to receive the topping layer complete all as specified and directed. , M&L cement concrete work in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using400 kg of cement per cubic metre, including necessary use & wasteof formwork for laying pavement of hardstanding in bays between joints & contraction ,expantion joints or between the two contraction jointscomplete all as specified and directed. , Finishing surface of concrete , by brooming, complete all as specified and directed. , Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ of thickness of concrete slab in 150 mm,complete all as specified and directed. , Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade A ,complete all as specified and directed. , M&L for PCC1:3:6 type C-2 using 40mm graded stone aggregate,asin drain andsurface channel, foundationetc complete all as specified and directed. , Demolition of brick work built in cement mortar including all quoions, arches pillar etc complete all as specified and directed. , M&L brick work with sub class B old size bricks, straight or curved on plan exec 6m mean radius built in CM 1:6 complete all as specified and directed by the Engineer-in-Charge , M & L for rendering 15 mm thick on fair face of brick walls or concrete surface in CM 1:4 complete finished even and smooth without using extra cement complete all as specified and directed. , M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement,ncluding forms, moulds, mi- tred/stopped ends etc.complete all as specified & as directed , Add or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete, using ex- tra cement,ncluding forms, moulds, mi- tred/stopped ends etc. complete all as specified & as directed. , Dismantling floor, hearth or wall tilling including cement mortar bedding(but not backing), and rubbish offpremises etccomplete all as specified and directed by Eng-in-Charge. , M & L coloured non-skid ceramic tiles joint free ceramic tiles 7 to 8 mm thick( square / rectangular) area of each tile exceedingeeding 0.11 sqm but not exceedingeeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed by Eng-in-Charge. , M&L coloured glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over 10 mm thick backing coat in cement mortar 1:3 complete all as specified and directed by Eng-in-Charge. , M & L for rendering 10 mm thick on fair face of brick walls or concrete surface in CM 1:6 complete finished even and smooth without using extra cement complete all as specified and directed by Eng-in-Charge. , M & L for preparation ofbrick or concrete. surfacesand applying 2 coats of oil bound distemper over a coat of primer complete all as specified and directed by Eng-in-Charge. , M & L rendering 15 mm thick in cement plaster 1 : 4 on fair faces of brick wk or concrete surface finishing the surface even and fair complete all as specified and directed by Eng-in-Charge. , M & L for preparation of new surface of wall including cornices and apply two coat of cement based paint complete all as specified and directed by Engineer-in-Charge. , M & L for rendering 5 mm thick on ceiling or concrete surface in CM 1:3 complete finished even and smooth without using extra cement complete all as specified and directed. , M & L for preparation of new surface of ceiling including cornices and apply two coats of white wash complete all as specified and directed by the Engineer-in-Charge. , M&L applying two mm thick wall care putty on walls and after drying the surfaces sand the putty smooth before painting complete all as specified and directed. , M&L applying two mm thick wall care putty on ceilings and after drying the surfaces sand the putty smooth before painting complete all as specified and directed. , Taking down chowkhat with shutter without taking off shutter from chowkhatof any description not exceeding 1.5 Sqm each completeall as specified and directed. , Taking down chowkhat with shutter without taking off shutter from chowkhatof any description exceeding 1.5 Sqm but not exceeding 4 Sqm each completeall as specified and directed. , S & F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tubecomplete all as specified and directed . , S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MSframe shall be covered with heat moulded plain colourPVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part – I 2009 and complete all as specified and directed. , S&F of anodised aluminium frame for doors ,windows, ventilators with one or more rebates including and not to paid separetly joining cleat,screws as requered for fixing etc and for Powder Coating above to (minimum thickness of powder coating 50 micron) complete all as specified and directed. , S&F sheet glass, ordinary quality, of 5.5 mm thick in squares not exceedingeeding 0.5 sq. m each pane complete all as specified and directed. , S&F of anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including ( and not to paid separetly) necessary joining cleats, glazing clips,glazing anodised aluminum snap beading, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.)for powder coating of any colour (Thickness or powder coating not less than 50 micron) complete all as specified and directed. , S&F anodised aluminium grill ( anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15 ) of approved designed/pattern with approved standard section and fixed to the existing window frame with C.P. brass or stainless steel screws @ 200 mm c/c , including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening , all complete as per requirement and direction of Engineer-in- Charge complete all as specified and directed. , S&F of Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including ( and not to paid separetly) necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. , S&Fstainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. , S&F Aluminum anodised barrel tower bolt of extruded section and fixed 125 mm long complete all as specified and directed . , S&F 150mm size extruded aluminium alloy handles, fabricated type,anodised complete all as specified and directed . , S&F 250mm aluminium alloy, anodised,sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixingboltts and sliding bolts of extrude section or cast aluminium complete all as specified and directed . , S&F Butt hinges, heavy weight, cold rolled mild steel, and fixed 75mm longcomplete all as specified and directed. , S&F GI water tubing/pipe 15 mm bore with alll fittings fixed to wall or laid in floors or celings including taking out old rusted pipes in any positioncompete all as specified and directed. , S&F GI water tubing/pipe 20 mm bore with alll fittings fixed to wall or laid in floors or celings including taking out old rusted pipes in any positioncompete all as specified and directed. , S & F in repairs 15mm Chromimum Platedpillar cockcompete all as specified and directed.. Make - Cera Cat Part No F1018101or equivalent make as specified in Appendix B list of makes. , S & F in repairs 15mm Chromimum Plated long body angle cock with wall flange compete all as specified and directed. Make CeraCat Part No F1018201 or equivalent make as specified in Appendix B list of makes. , S & F in repairs 15mm CP 2 way bib cock with single handle & wall flange compete all as specified and directed. Make CeraCat Part No F1018151 or equivalent make as specified in Appendix B list of makes. , S & F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position compete all as specified and directed. , S & F in repairs towel rail 600mm stainless steel compete all as specified and directed. Make - CeraCat Part No F5007103or equivalent make as specified in Appendix B list of makes. , S & F in repairs 110/100 mm PVC (SWR) Pipes single socketed in any length with rubber ring joints fixed to wall and floors compete all as specified and directed. , S & F in repairs 75 mm PVC (SWR) Pipes single socketed in any length with rubber ring joints fixed to wall and floors compete all as specified and directed. , S & F in repairs soap dish compete all as specified and directed. MakeCera Cat Part No F5007106 or equivalent make as specified in Appendix B list of makes. , S/F 110mm PVC (SWR) bends any radius compete all as specified and directed. , S/F 75mm PVC (SWR) bends any radius compete all as specified and directed. , S & F in repairs paper holder with flap guard compete all as specified and directed. MakeCeraCat Part No F5007110 or equivalent make as specified in Appendix B list of makes.. , S & F in repairs ball brass valves,high pressure, with polythelne float and fly nutin 20mm bore complete all as specified and directed. , S & F in repairs 15mm Chromimumlong body bib cock with nozzle and flange complete all as specified and directed. Make :-PrayagCat Part No 7305 or equivalent make as specified in Appendix B list of makes. , S & F in repairs 15mm CP 2 way bib cock long bodywith flangecomplete all as specified and directed. Make-Prayag or equivalent with Cat Part No 7312 or equivalent make as specified in Appendix B list of makes. , S & F in repairs concelated stop cock 15mm with flangecomplete all as specified and directed. Make - Prayag or equivalent with Cat Part No 7318 or equivalent make as specified in Appendix B list of makes. , S & F in repairs 15 mm Stop valves,/gate valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. , S & F in repair 20mm Stop valves/gate valve, cast copper alloy, screwed down, high pressure, with crutch or utterfly andle,screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. , S & F in repairs white plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. , S & F in repairs 110mm PVC (SWR) P trap complete all as specified and directed. , S & F in repairs 110mm PVC (SWR) S trap complete all as specified and directed. , S & F in repairs vitreous china squatting pan, Orissa pattern, size 580 x 440 mm, white, with integral foot rests complete including provision of lime concrete bedding and connection to trap, & to flushing pipe, anti-syphonage pipe, etc, complete including making good to floor complete all as specified and directed. , S & F in repairs vitreous china wash down water closed pan (pedesstal pattern/EWC), white with fixing bolts, trap, including connection to drain (or outgoing pipe) & to flushing pipe, antisyphonage pipe, etc, seat and cover complete all as specified and directed. , S & F in repairs white 10 Ltrs PVC valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, connections to pipe complete all as specified and directed. , S & F in repairs wash hand basin, vitreous china (flat back or angle back type)550x400mm size, including cutting for and pinning in ends of brackets or erecting stand including brackets complete all as specified and directed by Engr-in-Charge , S & F in repair 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. , S & F in repair grating doom 100mm dia of PTMT (Min weight 25 gms) complete all as specified and directed. , S & F in repair PVC connection pipe 15mm size with PTMT nuts of length 600mm complete all as specified and directed. , S & F in repairs PVC waste pipecomplete all as specified and directed. , Dismantling water tanks of 1000 Ltrs capacity complete all as specified and directed. , S & FRotational moulded polethelene water storage tanks in 1000 litres capasity (cylinderical vertical & triple layered with closed top) hoisted and fixed in position all as specified in SSR Pt-I complete, ISI marked, all as specified and directed. , Excavation in trenches n.exceeding 1.5mtr wide and n.exceeding 1.5 mtr in depth for foundation etc not exceeding 10 sqm on plan and getting out soft/loose soil complete all as specified and as directed. , M & L for Cement concrete(1:4:8) type D-2(40 m graded broken stone aggregate ) as in foundation of manholes complete all as specified and directed. , M&L for cement concrete (1:4:8) type D2 using 40 mm graded stone aggregates as in concrete bed to 150 mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested and complete all as specified and directed. , Brick work with subclass ‘B’ bricks, straight or curved on planot exceedingeeding 6m mean radius built in CM 1:4 complete all as specified and as directed. , M & L for Cement concrete 1:2:4 type B-0 (using 12.5 mm graded stoneagg.) as in benching and coping including necessary moulds and form works and finished exposed surfaces and channels using extra cement. , M & L for15 mm thickrendering on fair faces of concrete or block masonary surfaces in CM 1:4 mixed with integral water proofing compound @ 3% by weight of cement andfinished even & smooth without using extra cement complete all as specified and directed. , Supply only integral water proofing compound complete all as specified and directed. , M & L for Pre cast reinforced cement concrete 1:2:4 type B-I using 20 mm graded stone agg. As in cover slab of man holes including necessary form work and set in CM 1:4 complete all as specified and directed. , M&L for 150mm dia Reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and as directed. , M&L for cutting into existing manhole for connecting new drains, making good to drain pipe internal dia and rendering, cutting out existing benching for and forming branch channel in cement concrete 1 :2:4 type B1 using 20mm graded stone aggregate smooth finished & reforming benching as required complete all as specified and as directed. , Returning, filling in including spreading, leveling, water in and well ramming in layer n.exceeding.25 cm in soft/loose soil complete all as specified and as directed. , Removing exceedingavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding. 1.5 m above the starting point complete all as specified and as directed. , M&L Septic tank exceeding in ordinary soil, foundation in PCC 1:2:4 brick work in CM 1:4 , RCC slab covers including RCC Perecast manehole cover having 6 mm plate imbedded all around reinforced cover with angle iron frame bent shaft and sludge chember etc complete for 50 users and as per specified and directed in drg No.CEAF (NGP)/2004/TD/43 Sheet No. 1/2, and 2/2 , M&L soakage wells exceedingavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonrymade of sub class B old size bricks masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats and size 1.8 M Dia x 3.0m depth complete all as specified and directed in drg No.TD 217 of CELZ Sheet No. 1/2, and 2/2 (Revised) , M & L for 75mm ThickCement concrete type C-1, 1:3:6 (20mm graded stone aggregate) in Plinth Protection etc. including necessary formwork complete all as specified and directed by Eng-in-Charge. , M&L providing chequered cement concrete coloured tiles glossy finish 25cm x 25cm x 22 mm thick set, jointed and pointed in neat cement slurry with grey cement and pigmentlaid over and includingscreed bed or bedding layer 20 mm thick in CM 1:4 as in floors complete all as specified and directed. , M&L for providing100 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate , finished even and fair etc complete all as specified and directed by Engr-in-charge. , M&L 100mm thick cement concrete( 1:1.5:3) using 20mm graded aggregate Nominal mix as infloor including neccesary form work and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engr-in-charge. , M&L 30 mm thick wearproof topping of metallic floor (40kg of cement ,10 kg metallic floor hardenerand 0.034cum of granite chips for one sqm area of floor)as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings, and finished even and smooth complete all as specified and directed by Engr-in-charge. Note:-Quoted rate deemed to include the cost of metalic floor hardner , Forming 20 mm thick expansion joints filled withpre-formed bituminous filler and top 30mm primed andsealed with sealing compound, Grade A complete all as specified and directed. , Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade A complete all as specified and directed. , Dismantling wall and ceiling boards fiber,pulp,insulation etc any thickness including Grid, cover fillets etc complete all as specified and directed. , S & F grid false ceiling in GI system powder coated prelude main runner section 38 x 24 x 0.40mm, cross T 28 x 24 x 0.40mm, wall angle 24 x 24 x 0.40mm and including providing and fixing 4mm thick non asbestos fibre fire resistantcement building board/designer E-Board with all finishes size 595 x 595mm fixed in ceiling frame work with all necessary hanging washers, expansion holding fasteners,including 3mm thicksuspension wire as requiredetc for securing framework to ceiling wherever required complete all as specified and directed. , S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings ( TD Drawing No. - CE(AF)NGP/2003/TD/33 ) and as directed by of Engineer-in-charge. , M & L for preparation of old plastered surface of wall, ceiling incl.complete removal of existing treatment and washing, rubbing down and stopping of distempered and painted surfaces complete all as specified and directed. , M & L for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/ltr and UV resistance as per IS 15489:2004, alkali & fungal reistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon aditives at 1.43 ltr/10sqm over and including priming coat of exterior primer applied at 0.90ltr/10sqm all asspecified and directed by Engineer-in-Charge. , M & L for preparation ofsurface of wall including cornices and apply two coat of cement based paint over a coat a primer complete all as specified and directed by Engineer-in-Charge. , M & L for preparation of old wooden surface exceedingeeding 10Cm width or girth and apply one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge. , M & L for preparation ofsurfacesand applying two coats of white wash on wallcomplete all as specified and as directed by Engr-in-Charge. , M & L for preparation ofsurfacesand applying two coats of white wash on ceilingcomplete all as specified and as directed by Engr-in-Charge. , Taking down rolling shutter of sizeexceedingeeding 10 Sqm each from any position, any location including fittings and fixtures. Repairing / Replacing of unserviceable components and re-fixing on same opening in its original position after complete overhauling, greasing and oiling for smooth function and apply one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-Charge. Note: Components/Parts replaced under this item shall be measured & paid separately as supply only under respective items. , Supply Only MS cranked handles for operating gear operated rolling shutters made with hardened mild steel complete all as specified & directed by Engineer-in-Charge. , Supply only safety lever locks of mild steel with 4 levers with two keys for rolling shutters approved/ best quality complete as directed by Engineer-in-Charge. , Supply only Ball Bearing for rolling shutter to match the existing complete as directed by Engineer-in-Charge. , Supply Only spindle/ rails of rolling shutters complete as directed by Engineer-in-Charge. , Supply Only steel helical wires or flat spiral spring for rolling shutters to pull out the shutters including proper greasing for smooth movements/ functions complete as directed by Engineer-in-Charge. , S&Fin replacement 0.8 mm thick Plain black mild steel sheeting for cover hood of rolling shutter made channel or semi round shape including twp coats of synthetic enamel pain over one coat of red oxide primer Internal or External surface completeas directed by Engineer-in-Charge. , Supply Only 40mm bore MS pipe for shaft of rolling shutter as per length required at site complete all as specified & directed by Engineer-in-Charge. , Supply Only MS pulley / wheel made with flat iron 25x 6 mm of 160mm dia for revolving of rolling shutter in shaft complete as directed by Engineer-in-Charge. , Repair to locking plate/ locking arrangement by welding and providing missing part with new material using new nuts and bolts with locking arrangement for rolling shutter complete as directed by Engineer-in-Charge. , Dismantling of AC (corrugated/semi corrugated) sheet/PGI/CGI in roof covering including ridges all as specified and directed by Eng-in-Charge. , S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and making good to disturb surface, complete all as specified and directed. , Except sheeting pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and making good to disturb surface, complete all as specified and directed. , Dismantling stone slab floor, hearth or wall tilling including cement mortar bedding(but not backing), and rubbish offpremises etccomplete all as specified and directed. , M&L 15 to 18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and laid over and including 20mm thick screed bed or bedding layer in CM(1:6) complete all as specified and directed by the Engineer-in-Charge. , M&L joint free coloured non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceedingeeding 0.18 sqm but not exceedingeeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. , M & L for 40 mm thick Plain cement concrete 1:2:4 type B-1,(20mm graded stone aggregate) as in floor finished even and smooth without using extra cement laidover75 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge. , M & L coloured non-skid ceramic tiles joint free ceramic tiles 7 to 8 mm thick( square / rectangular) area of each tile exceedingeeding 0.11 sqm but not exceedingeeding 0.18 sqmas in skirting/dado etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick backing coat in cement mortar 1:3 complete all as specified and directed by Eng-in-Charge. , M & L for vitrified ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles area exceeding 0.18 sqm and not exceeding 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. , M & L for vitrified ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in skerting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coatin cement mortar 1:3 complete all as specified and directed. , M & L for preparation of old steel surface exceeding 10Cm width or girth and apply one coat of synthatic enamel paint complete all as specified and as directed by Engr-in-Charge. , S&F wire netting of stainless steel wire 1.23 mm dia fixed with tinned tacks of stainless steel wire staples average width of aperture 25mm and fixed to wall complete all as specified and directed , Demolition of brick work built in cement mortar including all quoions, arches pillar etc complete all as specified and directed by the Engineer-in-Charge. , Dismantling steel wrought iron or mild steel work of any description complete all as specified and directed. , S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exceedinglusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete for Fe .410 -w , grade E-250. complete all as specified and directed. , S&F gate pintal bush hinge for door or gate of size 1.5 to 2.0complete all as specifiiedand as directed by Engineer-in-Charge , Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete all as specifiedand the directions of Engineer-in-Charge. , S & F solar control film 25 micron reflective type sticked to glass planes as per instructions of manufacturers complete all as specified and directed. , S&F aluminium body door closer hydraulicaly regulated, designation No 1 universal type, suitable for door shutters upto 700 mm in width and of weight no more than 35 kg and fixed complete all as specified and directed. , S&F door lock for aluminium doors 6 lever of iron body ,silver colour with 03 pieces of key,make:Harrison of model H-0609-PK2 dimention 13x5.5x7 cm,360 gram or equivalent complete all as specified and directed. , Dismantling wrought iron or mild steel work of any description complete all as specified and directed. , S&F Fe 410 -W(Gde-E- 250)quality-A structural stell for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed. , Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding/ridge/valley gutter in wall/roof, fixed with self tapping screws complete all as specified and directed. , Taking down chowkhat with shutter without taking off shutter from chowkhatof any descriptionot exceedingeedingeeding 4 Sqm each completeall as specified and directed. , S & F for pressed steel door frames of size 125 x 60mm for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate etc completeall as specified and directed. , M & L for PCC type C-1 (1:3:6) using 12.5mm graded stone aggregate as in filling of hollow pressed steel frame etc completeall as specified and directed. , S & F 35 mm thick 2nd class hard wood glazed and skelton door shutter, open rebated and prepared to receive glass, gauze, etc(without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads forscuring glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I,section 8, clause 8.24 (a); supplied and fitted to chowkatscompleteall as specified and directed. , S & F30mm thick flush door shutters solid core construction, with block board core and plywood face panels, commercial type on both sidefixedto chowkhat completeall as specified and directed. , S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. , S&F butt hinges medium weight cold rolled mild steel 100mm size, ISI marked completeall as specified and directed. , S&F Aluminum barrel tower bolt 200mm complete all as specified and directed. , S&F aluminium anodised 300mm long sliding door bolt with hasp and staple (bolt type) and fixing clip and bolt extrude section or cast alloy type all as specified and directed. , S & F 300mm MS ordinary rat tail rod pattern springs, incl roller and roller plate completeall as specified and directed. , M & L for preparation of new or previously untreated surface of wood or wood based materials of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer completeall as specified and directed. , M & L forapplying two coat of oil bound distemper on ceiling including one coat of primer complete all as specified & directed by Engr-in-Charge. , M & L for rendering 10 mm thick on fair face of brick walls or concrete surface in CM 1:6 complete finished even and fair complete all as specified and directed. , S&F toughned glass of 10 mm thick including necssary fittings etc. complete all as specified and directed. , S & F in repairs PVC waste pipe complete all as specified and directed. , Dismantling water tanks of 500 Ltrs capacity complete all as specified and directed. , S & FRotational moulded polethelene water storage tanks in 500 litres capasity (cylinderical vertical & triple layered with closed top) hoisted and fixed in position all as specified in SSR Pt-I complete, ISI marked, complete all as specified and directed. , Taking down carefully (aluminium) point wiring complete of any type (batten/surface conduit or conB198:B234cealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as specified and directed. , Material and labour for point wiring includingconcealed/ fixed on surface of structure/ truss etc rigid non-metallic PVC conduit pipe medium grade, ISI marked heavy duty in size 20 mm diawith 1.5 sqmm FRLS insulated unsheathed, multi stranded copper conductor cable, single core 1100 volt grade with flush cast iron/ pressed steel terminal boxes of suitable size for fixing of switches, sockets and fan regulators etc piano / modular type accessorieswith 3 mm thick plastic laminated sheet cover and fixing with brass screws/cup washer and including FRLS insulated & unsheathed 1100 volts grade cable with multi stranded copper conductor of size 1.5 sqmm as continous earth wire complete including making good the disturbed surfaces complete all as specified and directed for the following:- Note ;- Quoted rate shall be included cost of cheasesing,cutting, plastering and colouring etc to surface of wall / beam / roof etc as site requiredmatchingwith existing surface and modular blank plate to be cover / fill up the extra gap / blank space ofmodular cover plate / mounting board in given module /make / model etc. , All as per item No 187 above, but one light/ fan point controlled by one way indepdentswitch. , All as per item No 187 above, but One 3 pin 5 Amps socket out let point on same board controlled by one switch. , All as per item No 187 above, but One 3 pin 5 Amps socket out let point on independent board controlled by one switch. , All as per item No 187 above, butAll as per above item No-2 here in before point wiring for 15 Amps socket using 2.5 Sqmm copper cable for phase and neutral and 2.5 Sqmm as earth wire complete. , Supply and fixing modular switch, one way 6 Amps 1 module complete all as specified and directed. Note ;-Lowest bidder shall be taken approval from Engineer-in-Charge for Colour , make , model and type of all modular accessories considered under this schedule / workbefore placing the order. , Supply and fixing modular switch, one way 16 Amps 1 module complete all as specified and directed. , Supply and fixing modular socket 6 A, 2/3 pin combined 2 module complete all as specified and directed. , Supply and fixing modular socket 16 A, 3/5 pin combined 2 module complete all as specified and directed. , Supply and fixing ceiling rose surface type 65 MM x 50 MM, 2 to 3 terminal complete all as specified and directed. , Supply and fixing modular fan regulator step type 120 W 2 module complete all as specified and directed. , Supply and fixing white cover plate with frame 3 module complete all as specified and directed. , Supply and fixing white cover plate with frame 4module complete all as specified and directed. , Supply and fixing white cover plate with frame 6 module complete all as specified and directed. , Supply and fixing white cover plate with frame 8 module complete all as specified and directed. , Material and labour for sub main wiring with two runs of single core PVC FRLS IS-694 cable with unsheathed multi-stranded copper conductor of size 1.5 Sqmm and drawing through in concelead rigid non metallic PVC conduit pipe medium grade heavy duty in suitable size with all necessary fittings including one run of FRLS insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm as earth wire (green in colour) and connected to common earth dolly complete including taking down of old unserviceable sub main wiring complete all as specified and as directed. Note;- (i) Two run of 1.5 sqmmwith one run of PVC conduit pipe shall be measured agaist one unit. (ii)Cost of cutting /chasing/ plastering /colouring etc as site shall be included matching to disturbed surface all as existed. , Material and labour for sub main wiring with two runs of single core PVC FRLS IS-694 cable with unsheathed multi-stranded copper conductor of size 2.5 Sqmm and drawing through in concelead rigid non metallic PVC conduit pipe medium grade heavy duty in suitable size with all necessary fittings including one run of FRLS insulated unsheathed stranded copper conductor cable of size 2.5 Sqmm as earth wire (green in colour) and connected to common earth dolly complete including taking down of old unserviceable sub main wiring complete all as specified and as directed Note;-(i) Two run of 2.5 sqmmwith one run of PVC conduit pipe shall be measured agaist one unit. (ii)Cost of cutting /chasing/ plastering /colouring etc as site shall be included matching to disturbed surface all as existed. , Material and labour for sub main wiring with two runs of single core PVC FRLS IS-694 cable with unsheathed multi-stranded copper conductor of size 6Sqmm and drawing through in concelead rigid non metallic PVC conduit pipe medium grade heavy duty in suitable size with all necessary fittings including one run of FRLS insulated unsheathed stranded copper conductor cable of size 6Sqmm as earth wire (green in colour) and connected to common earth dolly complete including taking down of old unserviceable sub main wiring complete all as specified and as directed Note;-(i) Two run of 6sqmmwith one run of PVC conduit pipe shall be measured agaist one unit. (ii)Cost of cutting /chasing/ plastering /colouring etc as site shall be included matching to disturbed surface all as existed. , Supply and fixingin replacement LED recessed mounted 2x2 luminaire LED 36 Wlight fitting energy saving low glare high power mounting on twoNos PVC round/ square block on surface of wall / beam etc incl making all electric connection using three core copper cable drawn through in PVC flexible counduit pipe from ceiling rose to fittings including taking out to unsv old fittings complete as directed. Make- Bajaj cat ref no BZRSQL 36W GZi NW and equivalent in Havells/Phillips/ Crompton , Supply and fixing LED tube light fitting with frame, driver etc in 20 W4 feet long white colour mounting on tow Nos of PVC round/ squire block on surface of wall / beam etc incl making all electric connection using three core copper cable drawn through in PVC flexible counduit pipe from ceiling rose to fittings including taking down to old unserviceable fitting with accessories complete as directed. , Supply and fixing LEDBldg security light fittings 35 watts energy savingincl making all electric connection using three core copper cable drawn through in PVC flexible counduit pipe from ceiling rose to fittings and mounting bracket made out by GI pipe light grade in 25 mm dia of bore in required length bend in 120 degree fixedwith clamp made out by GI strip in size 32 x4 mm usingnut bolt and washer etc including taking down to old unsv fitting with accessoriescomplete as directed. , Material and labour for sub main wiring with two runs of single core PVC FRLS IS-694 cable with unsheathed multi-stranded copper conductor of size 10 Sqmm and drawing through in concelead rigid non metallic PVC conduit pipe medium grade heavy duty in suitable size with all necessary fittings including one run of FRLS insulated unsheathed stranded copper conductor cable of size 10 Sqmm as earth wire (green in colour) and connected to common earth dolly complete including taking down of old unserviceable sub main wiring complete all as specified and as directed. Note : (i) Three run of 10 sqmmwith one run of PVC conduit pipe shall be measuredone unit. (ii)Cost of cutting /chasing/ plastering /colouring etc as site shall be included matching to disturbed surface all as existed. , Material and labour for sub main wiring with two runs of single core PVC FRLS IS-694 cable with unsheathed multi-stranded copper conductor of size 4 Sqmm and drawing through in concelead rigid non metallic PVC conduit pipe medium grade heavy duty in suitable size with all necessary fittings including one run of FRLS insulated unsheathed stranded copper conductor cable of size 4 Sqmm as earth wire (green in colour) and connected to common earth dolly complete including taking down of old unserviceable sub main wiring complete all as specified and as directed. Note : (i) Three run of 4 sqmmwith one run of PVC conduit pipe shall be measuredone unit. (ii)Cost of cutting /chasing/ plastering /colouring etc as site shall be included matching to disturbed surface all as existed. , Supply and fixing double door IK-09vertical TPN DB 8 way with 63 Amp MCCB incomer, with CRCA sheet steel, RAL 9003, powder coated provided with insulated vertical phase bus bar, neutral bars with shrouds, earth bars sticking saddles, cement spill protector, colour coded inter connecting wire set, cable ties, blanking plate and circuit identyfication lable, including MCCB 63 Amp TPN complete all as directed by Engr-in-charge. Make- L&T/Indoasian/Siemens , S&F VTPN 4 way double door prewired distribution board TPN-DPX 125 MCCB including one No MCCB 125 Amps, 25 kA, 4 pole as incomer and suitable SPN/TP MCBs as outgoing double door type sheet metal enclosure 415V with 200 Amps rated standard busbar of suitable size plate and common neutral link without MCBs with blank plate suitable for 4 way complete and including taking down VTPN DBs all complete all as specified andas directed by Engineer-in-Charge. Make: Schneider cat part No LV426268 (MCCB) and cat part No NBKRENEZVDD04 (VTPN)or equivalent in Legrand/ L&T Note : Rates of MCCB and MCB SPN/SP/TP shall deemed to be included in the quoted rates. , M&L Triple pole and earth 32Amp encolsure with a three pin and earth plug with socket complete with one triple pole MCB complete all as specified andas directed by Engineer-in-Charge. , Supply and fix sheet metal enclosure for MCB distribution board SPN, double door, 8 way with 200 Amp rated bus bar 230 Voltsconcealed in the surface of wall including taking down of old unserviceable DBs with accessories complete all as specified andas directed by Engineer-in-Charge. , Supply and fixing MCB , SPN, 2 pole 220 volts , 40 Amps , C Curve 10 KA complete all as specified andas directed by Engineer-in-Charge. , Supply and fixing MCB , single pole215 volts , 40 Amps , C Curve 10 KA complete all as specified andas directed by Engineer-in-Charge. , M&L MCCB 3 Pole, 415 V, fixed type, 25 to 100 Amps with breaking capacity 16 KA complete all as specified andas directed by Engineer-in-Charge. , Supply and fixing as new BLDC ceiling fan in size 1200 MM sweepwhite colour5 star rated copper wound energy saving with set of sweep/ extension rod / U clampand other accessories single phase 50 Hzsincl making electric connection using three core copper cable drawn through in PVC flexible conduit pipe complete. including taking down old unsv Ceiling fan and deposit to MES store complete all as specified andas directed by Engineer-in-Charge. , Supply and fixing as new exhaust fan 300 mm sweep steel body heavy duty with louver mounting bracket ISI marked 4 star rated energy saving less noise capacitor type incl making hole in brick wallplastering colour coading and all site requiredwork for disturbed surfacematching with existing and making electric connection using three core copper cable drawn through in PVC conduit pipe complete all as specified and directed including taking down old unserviceable Exhaust fan and deposit to MES store complete all as specified andas directed by Engineer-in-Charge. , Supply and fixing as newexhaust fan 600mm sweep steel body industrial heavy duty with louver mounting bracket ISI marked 5 star rated energy saving less noise capacitor type incl making hole in brick wallplastering colour coading and all site requiredwork for disturbed surfacematching with existing and making electric connection using three core copper cable drawn through in PVC conduit pipe complete all as specified and directed including taking down old unserviceable Exhaust fan and deposit to MES store complete all as specified andas directed by Engineer-in-Charge. , S&F Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified andas directed by Engineer-in-Charge. , S&F Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32x6mm galvanised iron strip complete all as specified andas directed by Engineer-in-Charge. , M&L in replacement earthing complete withgalvanized steel earth plate 600 x600 x 6mm thick, buried directly in ground(earth pit not less than 2.25 Mtr deep below ground level) with top edge of the plate not less than 1.5 Mtrs belownormal groundlevel, connected to galvanized GI earth lead wire 4.0mm dia as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints including excavation and earth work, GI pipe light grade 40 MM bore for protection of GI strip from earth electrode and 15 MM as watering with wiremesh funnel charcoaldust, common salt, PCC (1:2:4)type B-1 using 20 MMgraded stone aggregate for chamber and MS angle iron frame 40x40x3 MM and RCC cover 40 MM thick (1:2:4)type B-1 using 20 MM graded stone aggregate reinforced with 6 MM dia round bars@75 MM C/C both ways with MS handle 12 MM dia , PGI funnel and wire mesh , 20 MM bore GI Pipe light grade for wateringcomplete all asshown in electrical plate No 3 of SSR Part-I(2009) and connected to earth test point including testing complete all as specified and directed. Note : Quoted rate shall be included the cost of srtip upto 7.5 Mtr and required earth work. , Supply, laying and spreading of dry (Ganga) sand, free from organic impurities for cushioningas in trenches 8cm depth below cable and 15cm above cable andpunned to 10cm depthcomplete all as specified & directed. Note :- Punned thickness shall be considered for measurement purpose. , M&L brick, sub class B bricks laid dry, flat, length equal to width of brick over sand cusioning in trenches for cable protection complete all as specified and directed. , Labour only for cutting/boring to plinth protection/hard standing/road etc in suitable depth and corssing ofGI pipe of size 80 MM bore so that XLPE under ground cable can bepassed andgiving mechanical protection to cable complete all as specified and directed. Note:- Quoted rate shall be included the cost of required material for repairing to disturbed surface all as per existing specification and GI pipe shall be measured and paid seperately under respective itmes. , Supply and fixing in replacement50mm dia GI tubing (light grade) fitting for laying of underground cable below plinth protection/hard standing/road etc for cable protection complete all as specified & directed. , Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded,galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.50 core complete all as specified & directed. , Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded,galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.50 core complete all as specified & directed. , Supply, installation, testing and commessioning of LT Panel suitable for 415 volts 3 Phase 4 wire 50 Hz AC supply system out door type floor mounting along with factory made type panel weather proof, vermin proof, fully ventilated both side opening and fabricated out of MS CRCA sheet 3.15 mm thick & frame angle of size 50x50x6mm having bus bar of aluminium 160 Amps cap three phase and one neutral fixed on insulator and bus bar insulated by coloured heat shrinkable sleeve & housed in specified compartment both side openable including powder coating internally externally the entire steel surfaces. All the cover shall have with suitable locking arrangements fully internally wired with suitable size of thimble Incoming/outgoing internal connection with PVC insulated PVC sheathed multistranded copper wire of suitable size all as directed. The panel should be CPRI approved manufacture to accommodate the following incoming & outgoing controls with suitable size of digital volt meter & digital Amp meter with CTs and selector switches and including grouting KIOSK on floor (60cm above the ground surface) in floor angel iron 50x6mm imbeded to fixed the KIOSK with nut bolt, floor PCC (1:2:4) type B1 using 20mm grade stone aggregate complete and comprising following:- , IncomingMCCB 4 pole, 100Amp capacity, adjustable type with rupturing capacity 25 KA- 01 No. Outgoing(i)MCCB 4 pole, 63Amp capacity, adjustable type with rupturing capacity 25 KA- 02 Nos. (ii)Digital volts meter rating3 phase class 1- 01 No (iii) Digital Ammeter rating 3 phase 1A class 1 - 01 No (iv) Aluminium bus bar suitable size and thickness for RYB current rating 160Amp (v) Indicator lamp plate typefor RYB - 03 Nos (vi)All incoming and outgoing connection in MCCB/fitments carried out through suitable rating aluminium strip/lugs. , Supply. Install, testing and commisioning of LT Panel in cubical housing cabinet, out door type, platform mounted (minium height 45 cm above normal GL and 30 cm below normal GL) , CPRI approved factory made, totally enclosed, dust and vermin proof made out by3.15 MM thick CRCA MS sheet of suitablesizeand full built upon angle iron frame in size 40 x 40 x 6 MM, having front and rear hinged both side openable doors and liffting lugs (02 Nos) , locking arrengement to be connect to earthing strip at rear side, bottom detachable both side openable ,gland plate complete with suitable size zinc plated and passivated nut, bolts, spring and washers sheet steel bus bar chambers having front hinged covers with a set of electrolytic grade high conductivity.The cabinet and all members should be chemically treated with MSR solution for anticorrosive treatment. The panel shall be epoxy powder coated and the control circuitshall be connected bymulti strandered copper conductor flexible wire 1.5 Sqmm in proper colour coading and drawn through in flexible conduit. The panel should be suitable for 415 volts ,50 Hzs, 3 phase,4 wire system ,suitable rating CTs and PTs . internal connection shuold be made by copper strip in suitable rating ,making incoming and outgoing connection using gland in suitable size including grouting KIOSK on floor (60 CM above the ground surface) in floor angel iron 50 x 6 MM imbeded to fixed the KIOSK with nut bolt, floor PCC (1:2:4) type B1 using 20 MM grade stone aggregate ( minium 50 CM above GL and 30CM below GL)complete comprising the following items: , (a)04 Nos bus bars equal size made out of aluminium conductor strip in colour coating 200 Amps rated mounting on both side heat shrinkable insulators and PVC sleeving. - 01 Set (b) LED indicating lamps of R Y and B phase.Set of three - 01 (c) Digital volts meter rating3 phase class 1-01 No (d)Digital Ammeter rating 3 phase 1A class 1 - 01 No Incoming :-MCCB ,160 Amps rated, 4 pole, TPN, 415 volts grade , 36 KA breaking capacity microprocess based oprated- 01 Nos Outgoing:- MCCB ,63 Amps rated, 4 pole, TPN, 415 volts grade , 16 KA breaking capacity thermal megnatic based oprated - 04 No Note : (i)Panel drawing shall be approved by Engineer-in-Chargefor size/qty/ Tech specification before placing order(ii)All MCCB shall be confirming to Icu 100% and IEC 60947 -2 . in compact series , M&L in replacement earthing complete withgalvanized steel earth plate 600 x600 x 6mm thick, buried directly in ground(earth pit not less than 2.25 Mtr deep below ground level) with top edge of the plate not less than 1.5 Mtrs belownormal groundlevel, connected to galvanized GI strip 32 x 6 MM as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints including excavation and earth work, GI pipe light grade 40 MM bore for protection of GI strip from earth electrode and 15 MM as watering with wiremesh funnel charcoaldust, common salt, PCC (1:2:4)type B-1 using 20 MMgraded stone aggregate for chamber and MS angle iron frame 40x40x3 MM and RCC cover 40 MM thick (1:2:4)type B-1 using 20 MM graded stone aggregate reinforced with 6 MM dia round bars@75 MM C/C both ways with MS handle 12 MM dia , PGI funnel and wire mesh , 20 MM bore GI Pipe light grade for wateringcomplete all asshown in electrical plate No 3 of SSR Part-I(2009) and connected to earth test point including testing complete all as specified and directed. Note : Quote rstes shall be included the cost of srtip upto 7.5 Mtr and required earth work. , Note:- (i) Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. The same shall be recovered from various payment to contractor before handing over old material. The contract amount shall be arrived at after deduction of Schedule of Credit from the total quoted amount in BOQ. (ii) Make of material shall be as per mentioned in Particular specifications or Appendix B to Particular specifications as approved by AGE (I) AF manauri
