Tender For Special Repair To Otm Building No P 10 Of Med Regt And Certain Other Sanctioned Work At Faridkot Mil Station.; 1 Taking down of chowkats or frames n.exc 1.5 Sqm each with shutters (without taking of shutters from the frames) complete all as specified. 2 Taking down of chowkats or frames exc 1.5 Sqm but n exc 4 sqm each with shutters (without taking of shutters from the frames) complete all as specified 3 S&F Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified 4 M&L for Aluminium Powder coating section for door/window / Ventilators/ partition etc frames & shutters including joining cleat, mullion, grills etc. sliding/ openable type complete of standard sections complete all as specified and directed by Engr-in-Charge. (Aluminium section shall be of make Jindal/ Hindalco/ Indalco). 5 M&L for anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified 6 S&F 4.00mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified 7 S&F sheet glass of 3mm,ordinary quality andglazing with oil putty in squares n.exc 0.5 Sqm in each pane, complete all as specified. 8 S&F 3mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified 9 S&F 35 mm thick2nd class hard wood plain framed panel shutters (any number of panels) with panels of timber flat on both sides (feather edges) or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as specified and directed by Engr-in-Charge 10 S&F 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framingplain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed 11 S&F 2nd class hardwood factory made glazed skeleton shutters 35 mm thick open rebated and prepared to receive gauge etc but divided into squares, with plain chamfered or rounded, metered and riveted sash bars any numbers complete all as specified and directed 12 S&F Galvanisedmild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanisedwire staples complete all as specified and directed by Engr-in-Charge. 13 S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube wood grain printed PVC sheet used instead of plain colour sheet and edges will be printed to match with printed sheet complete all as specified and directed 14 S&F Factory Made Solid PVC Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed 15 S&F 100 mm long butt hinges, medium weight, cold rolled, mild steel and fixed complete all as specified and directed 16 S&F 100 mm long, Stainless Steel hinges with stainless steel screws complete all as specified and directed 17 S&F 150 mm long Aluminium handles cast type anodised complete all as specified and directed 18 S&F 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed 19 S&F 150 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed 20 S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasps staple (bolt type)andfixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed 21 S&F MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed 22 S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed 23 M&L for preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified 24 M&L for preparation of new or previously untreated surface of wood or wooden based surface any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified 25 S&F in repair Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified 26 M&L for PCC 1:3:6 type C-0 using (12.5mm graded aggregate) as in back filling of pressed steel frames, bed blocks, coping, fixing of hold fasts etc including necessary formwork complete all as specified and directed by Engr-in-Charge 27 Demolition of existing any type offloor tiles,stone slab laid and bedded, pointed in any mortar, picking, sweeping clean and washing down with water to remove dust, etc including S&F Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles 15mm thick screed bed or bedding layer CM 1:4 for laying finishes, complete all as specified as directed by Engr-in- Charge 28 S&F Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, (400 X400 mm) as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles15mm thick screed bed or bedding layer CM 1:4 for laying finishes, complete all as specified as directed by Engr-in- Charge 29 Demolition of existing any type ofwall tiles,stone slab laid and bedded, pointed in any mortar, picking, sweeping clean and washing down with water to remove dust, etc includingS&F Glazed ceramic tiles (coloured tiles) in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 15 mm thick rendering in CM 1:4on other than fair face of brick work complete all as specified and directed 30 S&F Glazed ceramic coloured tiles with highlighter in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 15 mm thick rendering in CM 1:4on other than fair face of brick work complete all as specified 31 Demolition of cement Concretein cement in ground floors and paving n.exc 15 cm thickness (below or above ground level) complete all as specified and directed 32 Demolition of concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed 33 M&L for light shade Vitrified ceramic tiles 10mm thick (Square/ rectangular) polished area of each tilen.exc 0.36 sqm in floors etc. set and jointed in net cement slurry and pointed in white coloured cement to match coloured tiles, over 15mm thick screed bed in CM 1:4 complete all as specified and directed 34 All as per Srl item No. 33.00 here-in-before but as in skirting laid over 15mm thick rendering 35 M&L for cementconcrete 40mm thick type B-0 1:2:4 (using 12.5mm graded stone aggregate) complete all as specified 36 M&L for cement concrete 50mm thick type C-2, 1:3:6 using 20mm graded aggregate as in plinth protection/path finishing surfaces even and fair (without using extra cement) complete all as specified 37 Taking down cement plaster from brick walls/ ceiling or concrete of any description, racking out joints hacking for key scrubbing down with water etc complete all as specified 38 M&L for 15mm thick rendering onbrick work/block masonry in CM(1:4) with water proofing compound finished even and smooth without using extra cement complete all as specified.NOTE :- Water proofing compound shall be paid and measured separately 39 M&L for rendering 15 mm thick in cement plaster 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed 40 Supply only integral liquid WPC of approved make complete all as specified 41 M&L for 15mm thick rendering on brick work/ block masonry in CM (1:6) finished even and smooth without using extra cement complete all as specified 42 M&L for rendering 10 mm thick in cement plaster 1:3 on ceiling finished even and smooth without using extra cement complete all as specified 43 M&L for preparation of newly plastered or un-plastered surfaces of wall applying two coat of distemper oil emulsion white/tinted with a wall care putty finished surface complete all as specified and directed by Engr-in-Charge 44 M&L for preparation of newly plastered or un-plastered ceiling surfaces and applying two coat of white wash over a putti complete all as specified and directed by Engr-in-Charge 45 M&L for preparation of new ceiling surfaces plastered or unplastered and applying two coat of white washcomplete all as specified and directed by Engr-in-Charge 46 M&L for preparation of new plastered surfaces of walls including 3mm wall putty and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed 47 M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed 48 Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed 49 M&L for old size brickwork with fly ash bricks straight or curved on plan exc 6m mean radius wall built in cement mortar 1:6 complete all as specified and directed 50 M&L for brick work with fly ash bricks (old size bricks) straight or curved on plan exceeding 6m meanradius with old size bricks in wall built in cement mortar (1:6) complete all as specified 51 Taking up or down 15mm dia GI Tubing and connection including, cleaning for refixing or removal to store complete all as specified 52 All as per Srl item No 51.00 here-in-before but 20mm dia 53 S&F 15mm bore GI tubing medium grade with all fittings fixed to walls or laid in floors complete all as specified 54 S&F 20mm bore GI tubing med grade with all fittings fixed to walls or laid in floors complete all as specified 55 S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed 56 S&F 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed 57 S&F in repair 15mm angle cock/ stop cock with flange cast copper alloy, chromium plated, fancy type,(long shank cup concealed type),screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge 58 S&F15 mm fancy type chromium plated Angle valve/stop valve, screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified 59 S&F in repair 15mm bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified by Engineer-in-Charge 60 S&F 15mm bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified by Engineer-in-Charge 61 S&F in repairs CP fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in 15mm bore pipe complete all as specified and directed 62 S&F CP fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in 15mm bore pipe complete all as specified and directed 63 S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white CI P or S traps 100mm & PVC flush pipes 32mm diaincluding connecting to trap and to flushing pipe, anti-syphonage pipe etc including all joints and making good to floor complete all as specified 64 S&F in repair PVC 10 litre capacity valve less syphonic action type, flushing cistern, low level, white/coloured with inlet ball valve, float, PVC bend and handle including brackets, etc. complete all as specified by Engineer-in-Charge. 65 S&F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm diapipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed 66 S&F in repair Wash hand basin flat back 550x400mm vitreous china (white) with cantilever CI/Angle iron brackets embedded in concrete block including Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore, complete all as specified by Engineer-in-Charge 67 S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer-in-Charge 68 S&F in repairs brass chromium plated overhead shower 125mm size with or without swivel joints including fixing to steel pipe of 15mm bore complete all as specified and directed by Engineer-in-Charge 69 S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge 70 S&F in repair 600 mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-Charge 71 S&F in repair Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) complete all as specified and directed by Engineer-in-Charge 72 S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge 73 S&F in repair Toilet paper holder of brass CP fixed to walls with chromium plated (CP) brass screws complete all as specified and directed by Engineer-in-Charge 74 M&L in repairs CI Floor trap long neck 75 mm dia, with stainless steel grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) etc fixed complete all as specified and directed by Engineer-in-Charge 75 M&L for 75mm dia of long body PVC Floor trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 in repair complete all as specified 76 S&F 75mm cast iron vent cowls complete all as specified and directed by Engineer-in-Charge 77 S&F in repairs PVC (SWR) vent cowl 100 mm complete all as specified and directed 78 S&F in repair Rotational moulded polythylene 1000 capacity waterstorage tank (Cylindrical vertical with closed top) hoisted and fixed in position including 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. & dismantling of old water tank complete all asspecified 79 S&F in repair Rotational moulded polythylene 500 capacity waterstorage tank (Cylindrical vertical with closed top) hoisted and fixed in position including 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. & dismantling of old water tank complete all as specified 80 Excavating in trenches, n.exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified 81 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified 82 Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified 83 Demolition and breaking up drain pipes 150mm internal dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified 84 M&L for 150mm bore RCC NP2 drain pipes laid in trenches and jointed with collars all as specified and directed 85 M&L for 150mm bore Concrete bed (PCC 1:3:6 type C2)to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified 86 Demolition of concrete (unreinforced) in roofs any thickness incl plastering and leaping (whether full thickness removed or only part thereof) complete all as specified and directed by Engr-in-Charge 87 M&L for rendering 10mm thick in cement plaster 1:3 with WPC on roof finished fair and even complete all as specified 88 M&L for Roof Treatment as specified below and as directed :(a) Cleaning, washing of surface and removing all existing bitumen coatings completely with intense wire brushing or high speed water jet. Surface should be free from any loose paint, dust or grease.(b)All cracks upto 3mm at corner joints, channels and parapets should be treated with crack seal and bigger cracks, damaged portions and hollow areas must be repaired with polymer modified cement mortars.(c)Applying one coat of PrimeSeal/ Epoxy Primer/ShaliUrethane BTD White diluted with potable water in the ratio of 1:1 and apply @ 0.40 kg/ sqm (0.20 kg BTD+0.20 Kg water)(d)Laying polyster reinforced fiber net/50 gsm Geotextile mesh, upto 300 mm on walls.(e)Applying three coat of Hydro-Shield PUD micro-fibre reinforced UV resistant polyurethane (solid content 68% ) / Damp Proof ultra UVStable fibre reinforced elastomeric liquid waterproofing membrane formulated with PU hybrid polymers (Solid content 55%)/ Smart-Care PU Magnum elastomeric waterproofing coating based on hydrophobic polyurethane (solid content 85%)/Single Component Elastomeric Liquid Membrane Shali-Urethane BTD White/coloured(Elongation 400% ± 50, Solid Contents > 80% & Specific Gravity @ 30 OC 1.5 ± 0.03) @ total 2.00 Kg per sqm in two coats for maintaining thickness of 1.5mm,with paint brush/ roller upto 300 mm on walls.Make : DrFixit/ Asian/STP 89 M&L for anodised aluminium snap grid frame work for false ceiling all as specified hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified perforated particle board/tiles 12 mm thick for insulation and acoustic purposes, 60x60 cm in size, fixed frame work or with staples on snap grid complete all as specified 90 Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed 91 M&L for mild steel Fe 290 Gde E-165 in Stairs(framed) including stringers, trades, landing, balusters, hand rails, cooler stand, ladder, guard bars and framed work etc. including cleats, brackets, etc. complete all as specified 92 M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint including preparation of surface complete all as specified. 93 Dismantling CI/AC /RCC/PVC pipe alongwith fittings of 75 mm dia, below or above GL, laid in floors or fixed to walls jointed in cement mortar and taking out complete all as specified 94 S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified 95 S&F 100mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified 96 S&F in repair waste fittings 32 mm brass chromium plated for glazed ware sinks, basins etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge 97 Rough excavation not exc 1.5 m deep and getting out in soft or loose soil etc complete all as specified and directed. 98 Removal of excavated soil to a distance exc. 1.5 km but and n exc 5 km and deposited where directed at a level n.exc. 1.5 m above the starting point complete all as specified 99 M&L for 100mm Soling (or sub base) with broken boulders or quarried stone, interstices filled, surface formed and rolled and consolidated to required gradient and camber complete all as specified 100 M&L for 100mm thick PCC 1:4:8 type D-2 as in sub-base, foundation, mass concrete etc complete all as specified and directed 101 M&L for 25mm thick sand filling under floors, in foundation including watering and consolidation as required complete all as specified and directed 102 M&L for machine pressed pre-cast concrete interlocking paver block with grey cement and no pigment any shape & size conforming to IS 15658 - 2006 of 60 mm thickness, M35 Grade laying above sand cushioning surface etc complete all as specified and directed 103 M&L for factory made pre-cast cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in kerb stone of approximate any sizeas directed by Engineer-in-Charge including necessary form work with plain fair faces, including chamfers, weathering, throating etc set in cement mortar 1:4with joints to match for path edging etc; embedded in position including all necessary excavation, tamping ground around blocks and removal of rubbish/ surplus soil etc complete allasspecified and directed by Engineer-in-Charge 104 M&L for PCC 1:4:8 type D2 (using 40mm graded aggregate)in foundation, filling and mass concrete complete all as specified and directed 105 M&L for RCC M-30 (20mm graded aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed 106 M&L for RCC M-30 (20mm graded aggregate) in Columns, pillars, piers, posts and struts complete all as specified and directed 107 M&L for RCC M-30 (20mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed 108 M&L for RCC M-30 in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified 109 Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, flat, rough finished surfaces of concrete complete all as specified and directed 110 Formwork to sides of pillars, posts, struts, piers, column and stanchions, Square, rectangular or polygonal rough finished surfaces of concrete complete all as specified and directed 111 Form work tosides and soffits of floor or roof beam, beam, hauchings, girders, bressumemers, lintels, cantilevers, shelves incl supports overhangs etc also splays between floors and beams, flat, rough finished surfaces of concrete complete all as specified and directed 112 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed 113 Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm wide complete all as specified and directed 114 S&F MS TMT Bars of 10 mm dia and over, cut to length, bent to shape requiredincluding cranking, bindingspirally for hooping for columns hooking ends and bindingwithand including MS wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified. 115 S&F MS TMT Bars of 5 mm dia and overup to 10 mm diain stirrups, spacers and binders, cut to length bent to shape requiredincluding cranking, bindingspirally for hooping for columns hooking ends and bindingwithand including MS wire annealed not less than 0.9 mm dia or securing with clip complete all as specified. 116 M&L for Hardcore of broken stone or boulder of gauge exc 63 mm but n.exc 100 mm, deposited, spread and leveled in layers n.exc 15 cm thick, watered and rolled/ rammed to a true surface complete all as specified 117 M&L for 25mm thickPCC 1:2:4 type B-0 (Using 12.5 mm graded aggregate), as in flooring complete all as specified. 118 M&L for Rendering 15 mm thick in cement plaster 1:6on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing,finished even and smooth without using extra cement complete all as specified 119 M&L for preparation of new surfaces of wall and applying two coat of cement base paint complete all as specified.Note :- Curing of surface will be carried out as per Para 15.15.3 of SSR Part-I 120 M&L for Polythene film, 300 micron thick @ 0.30 to 0.50 kg per sqm conforming to IS specification with lap joints 100mm complete all as specified 121 M&L for Granite (of any type) work 15 to 17 mm thick (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified 122 S&F Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, (600 X 600 mm)as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles15mm thick screed bed or bedding layer CM 1:4 for laying finishes, complete all as specified as directed by Engr-in- Charge 123 S&F Non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.36 sqm, (600 X600mm) cut to reqd size and shape as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed 124 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer, calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed by Engineer-in-Charge 125 M&L for 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed 126 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed by Engineer-in-Charge 127 S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded all as specified and directed by Engineer-in-Charge. 128 S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded all as specified and directed by Engineer-in-Charge. 129 S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed 130 S&F in repairs vitreous China squatting pan of Orrissa pattern of approved make of size 580mm x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to anti-syphonage pipe etc including making good to floor complete all as specified and directed. 131 M&L for 25mm dia Stainless steel curtain rod with brackets and knobs at both ends as per site requirement including taking down old existing curtain rods any description with accessories complete all as specified and directed.Note : The cost of brackets and knobs is deemed to be included in the quoted rate.Nothing extra shall be paid on this account. 132 S&F 110mm bore of pipe PVC (SWR) bends heavy grade of any radius/ shoefixed to PVC pipes complete all as specified and directed 133 S&F 75mm bore of pipe PVC (SWR) bends heavy grade of any radius / shoefixed to PVC pipes complete all as specified and directed 134 M&L for PVC (SWR) P’ trap 110mm dia heavy grade complete all as specified 135 M&L for PVC (SWR) junction single, (Single T), 100 mm bore, (equal or unqual), ordinary or inverted (spigot or socket type) or with oval access door as in repairs complete all as specified and directed by Engineer-in-Charge 136 S&F Salt-glazed stoneware gully traps 150x 150mm, square or round mouthed, type P’ complete all as specified and directed 137 S&F in repair SFRC (Steel fibre Reinforcement concrete cover & frame) HD-20mm, conforming to IS-12592, graded rectangular clear opening 560x560mmand fixed over manholeand make good of manhole complete all as specified and directed 138 OVERLAY: PU BASED ELASTOMERIC LIQUID MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, thermal insulating elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index 109 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541).(a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturer’s specification.(b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm/m² (minimum) or equivalent by brush/roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mesh of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry.(c) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm/m² (minimum) or equivalent by brush/roller.Make : Fosroc / Sika / Choksey / Chemsol / Bostik / STPNote:(i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm; if any shortfall in thickness of above treatment the same shall be achieved by additional coat.(ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE.(iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years 139 S&F in repair Ms powder coated decorative drapery rod (color as approved) of 20mm dia approved pattern & design including decorative knob (wall side and free side) & powder coated mild steel flat iron brackets fixed with steel screw and PVC rawl plugs/grips complete all as specified and directed by Engr-in-Charge. 140 S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates of Fe-410-W (Gde-E-250 quality-A) etc, complete all as specified and directed by Engr-in-Charge. 141 S&F pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having strength of 550 Mpa as in roof covering/cladding to wall, fixed wall self tapping screw complete all as specified and directed by Engr-in-Charge. 142 Taking down MCB, DB Including MCBs and making good to the disturbed walls and surface area etc all as specified and directed by Engr-in-Charge. 143 Taking down point wiring complete including fixture and fittings and making good to disturbed area all as specified and directed by Engr-in-Charge. 144 Taking down submain wiring 2 run / 4 run with earthing cable and making good to disturbed area all as specified and directed by Engr-in-Charge. 145 Point wiring complete with ISI marked 1.5 sqmm single core PVC insulated unsheathed cable 1100V grade FRLS with multi-stranded copper conductor drawn through PVC concealed conduit /surface in wall/roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanized steel pressed sunken terminal boxes of suitable sizes for mounting of switches, sockets, fan regulator etc covered with 2.8 mm thick plastic laminate Hylem top cover sheet of required color fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer includingfixing and 1.5 sqmm copper conductor as earth continuity to connect common earth dolly completed for the One light point/Fan point/ Exhaust fan point controlled by one way switch all as specified and directed by Engr-in-Charge:- 146 All as per Srl item No. 145.00 here-in-before but one three pin socket out let 5 amps on the same board with other switches 147 All as per Srl item No. 145.00 here-in-before but one 3 pin, 5A switch socket outlet point on independent board 148 All as per Srl item No. 145.00 here-in-before but with 2.5 sqmm cable for 16 amps socket outlet point on independent board including 2.5 sqmm PVC insulated unsheathed cable multi-stranded with copper conductor green in colour as earth continuity conductor. 149 All as per Srl item No. 145.00 here-in-before but with 4 sqmm cable for 16 amps socket outlet point on independent board including 4 sqmm PVC insulated unsheathed cable multi-stranded with copper conductor green in colour as earth continuity conductor. 150 M&L for ceiling rose 3 Terminal / PVC / polycarbonate isolated body complete all as specified 151 Supply and wiring with two single core PVC FRLSinsulatedcopper conductor 6 sqmm and same 6 sqmm for continuous earth wire drawn in to concealed PVC conduit complete all as specified and directed by Engr-in-Charge. Note: Cost of PVC conduit, conduit accessories and earth wire including in sub main wiring 152 S&F Piano type switch single pole 1 way 5/6 amps 230 volt AC supply complete all as specified and directed by Engr-in-Charge. 153 S&F socket two in one 5/6 Pin, 5/6 Amps 230 volt AC supply complete all as specified and directed by Engr-in-Charge. 154 S&F stepped type Electronic fan Regulator flush type 120 Watt complete all as specified and directed by Engr-in-Charge. 155 S&F Piano type switch single pole 1 way 15/16 amps 230 volt AC supply complete all as specified and directed by Engr-in-Charge. 156 S&F socket two in one 5/6 Pin 15/16 Amps 230 volt AC supply complete all as specified and directed by Engr-in-Charge. 157 S&F Modular switch 1 way 6 amps one moduleswitch all as specified and directed by Engr-in-Charge. 158 S&F Modular socket 6A 2/3 pin combined 2 modulesocket all as specified and directed by Engr-in-Charge. 159 S&F Modular switch 1 way 16 amps 1 moduleswitch all as specified and directed by Engr-in-Charge. 160 S&F Modular socket 6A / 16A - 2/3 pin combined 2 moduleall as specified and directed by Engr-in-Charge. 161 S&F LED bulb 1x10 Watt lamp having luminous efficacy warranty 2 year all as per specification & directed by Engr-in-Charge. Make-Havells/Philips/Bajaj 162 S&F PVC Lamp holder suitable for LED 5 to 20 watt bulb complete all as specified and directed. 163 S&F of LED tube light fitting 20W, (4 feet long) 230 V, surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver and including connections up with copper conductor wire with suitable size as per specification and directed. 164 Material, Labour, Installation and commissioning of desert cooler electric driven (single phase), having nominal air flow capacity of 6000 CuM per hour (or nearest size).(*Steel body)deep galvanised steel thickness 1mm body and 1mm removal side and back panel single phase 230 volts,with submersible pump of suitable size (Maximum power consumption 250 volts) ISI marker(with float valve of 15mm dia, stop valve of 15 mm dia, nut washer PVC connections of 15mm dia to air cooler complete all as specified.Note (a) : Sufficient length of 3 core PVE sheathed round copper cable size 23/076 to enable fixing in to plug point shall be provided by contractor. (b)Arrangement of power connections and water connections to the desert cooler will be included in installation. (c) No extra payment shall be made to float valve, stop valve, nut, washer PVC connection, leak proof joints etc and making connection from GI pipe 15 mm dia to air cooler in this regards) union for GI pipe ball valves brass complete including electric connection. 165 S&F ceiling fans complete with blades, down rod, remote and accessories, 230 V, 1200 mm Sweep. Min air delivery 245 CFM with service value 6.00 BEE, Five star rated with brushless DC motor (BLDC) complete all as specified and directed. 166 S&F in replacement Exhaust fan steel body AC single phase 230 V of size 300 mm Sweep with blades and frame and Louvers including cutting of suitable size of hole as directed by Engr-in-Charge. 167 S&F in replacement (concealed flush to wall) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 250 Amp rated bus bar) VTPN, 4 Way, suitable for mounting MCCB/MCB, conforming to IS-13032, DB shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-42 protection class, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessity complete all as specified and directed by Engineer-in-charge. 168 S&F MCCB 100 Amp 415 V, 16 KA, 4 Pole complete with connection and testing all as specified and directed 169 S&F sheet metal enclosure for MCB DBs SPN 240 volts 8 way double door complete all as specified and directed by Engr-in-Charge. 170 S&F amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 Amp, in the MCB DB complete with connection testing and commissioning. 171 S&F amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of SPN and current carrying capacity 63 Amp, in the MCB DB complete with connection testing and commissioning. 172 S&F 240V, 10 KA B curve miniature circuit breaker (MCB) of SPN and current carrying capacity5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning. 173 S&F 240V, 10 KA B curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed 174 S&F LED street light 25 watt luminaries comprising of epoxy powder coated housing, enclosed with glass cover including 40mm GI Bracket and fixing arrangement in road light, security light etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable 1.5 sqmm with suitable size and including taking down defective unserviceable street light any size as per specification & as directed by Engr-in-Charge. Make: Havells/ Philips/ Bajaj 175 S&F in replacement energy efficient LED Security light fitting of 25W pressure die cast aluminium housing/body, heat resistant clear toughened glass,better optics for uniform distribution street/Roadway luminaire, with driver, including electric connection, complete fitting with all accessories and following specifications, including taking down old Unserviceable light fitting any type complete all as specified and directed by Engineer-in-Charge :-(a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt.(b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95(e) THD : Max10%.(f) IP rating : IP66. (g) IK rating:Minimum IK07 (h) Built in potted LED Driver of the same make as of the luminaire.(j) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K.(m) CRI: Morethan 80 (n) Lens - High Efficiency wide angle lens.(o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily) 176 M&L for Earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead ofGI wire 4 mm dia (8 SWG) by means of bolts, nuts and washers of the earth wire galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia GI light grade with funnel & wiremesh, PCC chamber in cement concrete (1:2:4) type B1 including 40mm thick pre-cast RCC (1:2:4) type B0 cover and 40x40x6mm angle iron frame on top of pit cover and excavation & earth work completeall as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2020 complete all as specified and directed by Engr-in-charge.. 177 M&L for Laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sqmm 4 core in trenches/floors/wall and under road including connecting with suitable aluminium lugs and including taking up defective unserviceable cable of the any sizes all as specified and directed by Engr-in-Charge. Note: Earth work, Sand cushioning, GI pipe and cable cover for protection to be measured and paid separately. 178 Supply and spread dry fine aggregate sand in trenches for cable cushioning all as specified on both top and bottom of cable including ramming all as specified and directed by Engr-in-Charge. 179 Supply and lay Brick tiles; common burnt clay building bricks sub-class ‘B’ of standard size laid in trenches of across the cable protection all as specified and directed by Engr-in-Charge. 180 Supply and laying steel water Tubing, 50 mm dia ISI Marked, “light grade galvanised, laid in trenches/under road with all fitting including taking down old Unserviceable pipe any type complete all as specified. 181 M&L for stop valve, cast copper alloy, screwed down, high pressure, fancy type, chromium plated 15mm bore of pipe, screwed both ends for iron pipe and fixed complete all as specified and directed 182 Supply and laying steel water tubing, 15mm dia ISI marked, “Medium grade” galvanized including tube fittings viz tees socket bends elbows, union nipple etc screwed and socketed joint laid in trenches/ under road with all fitting complete all as specified and directed 183 M&L for cutting chases in bricks wall/ PCC walls for taking out blocked concealed conduits and making good to surface in cement mortar 1:3 and with finish to match the existing surface complete all as specified and directed 184 Supply and laying rigid non-metallic PVC conduit size 25mm exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, nuts, saddles, pipe hooks etc with all fitting including taking down old unserviceable pipe any type complete all as specified and directed 185 Supply and laying rigid non-metallic PVC conduit size 20mm exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, nuts, saddles, pipe hooks etc with all fitting including taking down old unserviceable pipe any type complete all as specified and directed 186 Supplying, fixing and commissioning of electric water heater (Gyser) storage type ABS body of capacity 25 ltrs, BEE approved 5 star rating, 230V,single Phase, AC supply inner tank made out of heavy duty stainless steel sheet (Designed with single weld line, factory tested with hydraulic pressure as per latest IS code) with glass lined quoting complete with all accessories such as safety valve thermostat NRV, connection piece PVC connectionfor hot and cold water 3 core PVC insulated PVC sheathed copper conductor flexible cable including 15 Amp plug suitable for existing socket and fixing material, 04 Nos nut bolt grouting in wall in PCC(1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and directed 187 Supply and laying of CPVC Pipe outer dia 16mmISI Marked, including tube fittings Viz Tees Socket bends elbows, union nipple etc screwed and socketed joint fixed on wall / trenches with all fitting complete all as specified. Note :-A Sum of Rs. 2,07,508.00 will be deducted on account of credit for dismantling/ demolished/ taking down material. Please refer detail on srl page No. 52 (Schedule of credit) of Tender Documents
