Tender For Special Repair Of Building No T 79 Squash Court At Faridkot Mil Station.; 1 Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed 2 S&F Pre-painted galvalume aluminum zinc coating GI based Corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws complete all as specified and directed by Engr-in-Charge 3 S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws complete all as specified and directed by Engr-in-Charge 4 Dismantling wrought iron, Structural steel work, wind tie or mild steel work of any description complete all as specified 5 S&F roof trusses (framed), trussed, purlins, crane granitries, rails and fastenings and heavy brackets framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming toFe-290(Gde-E-165)complete all as specified and directed 6 S&F mild steel wind ties for roof including securing bolts and necessary drilling, bolting etc conforming to Fe-290, E-165, complete all as specified 7 Dismantling boarding ofany description fixed in any position with nails, complete all as specified. 8 S&F Anodised aluminium snap grid Size of grid 605 x 605mm frame work for false ceiling complete all as specified 9 S&F hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilinglong complete all as specified and directed by Engineer-in-Charge. 10 M&L for providing PVC Gypsum board of 600mm X 600mm sizefixed to metal frame work and reinforced with GI wire mesh (fillets, metal frame work and GI wire mesh paid separately) complete all as specified and directed by Engineer-in-Charge 11 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified 12 M&L for vitrified ceramic tiles 10mm thick (Square/rectangular) light shade polished area of each tiles notexceeding 0.36 Sqmin floors set and jointed in neat cement slurry and pointed in coloured cement to match, 15mm thick screed bed or bedding layer CM 1:4 for laying finishes complete all as specified 13 S&F Glazed ceramic coloured tiles with highlighter in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in CM 1:4on other than fair face of brick work complete all as specified 14 Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified 15 M&L for brick work with sub class B bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified 16 Taking down cement plaster on brick walls of any description includingracking out joints, hacking for key, scrubbing down with water etc complete all as specified. 17 M&L for rendering 15mm thickin cement mortar (1:4) on any face of brick walls or concrete surfaces, with WPC finished even and smooth without using extra cement complete all as specified.Note : WPC will be measured and paid separately 18 M&L for preparation of newly plaster or unplastered wall surfaces and apply two coat of Acrylic smooth exterior paint over 1mm coat of wall care putty of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) complete all as specified and directed. 19 M&L for Acrylic polymer base damp-proof coating system with two component ready to use acrylic polymer modifieddamp-proof coating : 1. SURFACE PREPARATION: Remove the existing plastered surface with efflorescence/ seepage area. Non-moving cracks having width upto 5 mm must be filled with Polymer based crack filler. 2 APPLICATION: Apply acrylic polymer base damp proof coating by brush roller over SSD surface. Apply the first coat of damp proof coating with a paintbrush directly on the surfaces. Allow to dry for a minimum 2-3 hrs. Apply subsequent second layer after drying. The first coat and second coat must be applied in perpendicular direction. The coverage must be at least 1.2 sqm/kg/coat. The mixing for two component, if required, shall be done as per manufactures specifications. Rendering to be carried out after approval of Engr-in-Charge and shall be paid separately. Make : Asian Paints Damp proof Ultra 2K/Fosroc Damp Protect/Dr Fixit damp guardNote : Treatment shall be carried out through Authorized applicators only 20 Removing of existing wooden flooring to install new maple wood flooring complete all as specified 21 M&L for maple wood flooring surface board:- imported maple wood finished with 21mm thick, 57 to 83mm wide and in random length in tongue and groove shapes. The edges of the boards will have a finger lock groove and the bottom side with air pass groove and treated with special anti-termite and water resistant lacquer.The under frame:- made of best quality european pine wood sleepers of 70 mmx45 mm, treated with anti-termite solution and fixed on the bottom side with 10mm thick power pad rubber air cushioned pads, stapled through two wings at 300mmx300 mmInstallation: - ips subfloor treated with a vapor barrier to be placed on the levelled ips sub-floor before laying the under frame. the runners having air cushion pads to be placed on the vapor barrier in perfect level at 330 mm in 1 direction. the surface board to be screwed to the sleepers through the tongue only and will lock the screwed tongue by the groove of adjoining board. ends of the boards will be locked by inserting the wooden fingers through the edge grooves and fixed with suitable adhesive.Finishing: - after laying the flooring, the floor boards will be levelled to a uniform surface by sanding machine and sand paper then pu water based polish (1 coat sealer 2 coat pu) will be applied to surface for finishing 22 Supply and application of hard plaster system meeting specifications for squash court laid down by wsf approved specification. the system consists of a 10 mm base coat with silica sand provide by you at your cost and top coat of 3-4 mm, which makes it a total thickness of 13 - 14 mm. due to extremely hard nature of plaster a slight uneven colour distribution may be seen once the plaster has dried, this doesnt affect the strength or integrity of the plaster and must not be considered as a defect. area:- wall plaster playing area is only below red lines 23 S&F of free Standing Glass Back Wall Made of 12 MM Thick Toughened Glass With Four Panels, 1 Door, 4 Fines, Fixtures and Fitting and all the Materials Required For Erecting The Glass Walls. (Including Fitting & Installation) The Height of the Glass Wall will be 2130 MM Above the Finished Floor Level complete all as specified 24 M&L for Washable epoxy wall paint work for 1 squash court : supply and installation washable epoxy paint complete all as specified 25 S&F of squash court Soundboard complete all as specified and directed 26 M&L for Line marking on wall and floor of Squash Court complete all as specified and directedNote :-A Sum of Rs. 40,988.80 will be deducted on account of credit for dismantling/ demolished/ taking down material. Please refer detail on srl page No. 19 (Schedule of credit) of Tender Documents.
