Tender For Special Repair In Jco Mess Bldg No P 23 Of Med Regt Basantar River At Faridkot Mil Stn; 1 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directedby Engr-in-Charge 2 M&L for Light shade Vitrifieddouble chargeCeramic tiles 8-9mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over including 15 mm thick screed bedCM (1:6) and pointed in white or colour cement to matchcomplete all as specified & directed by Engr-in-Charge 3 All as per Srl item No 2 here-in-before but in skirting over 10 mm thick backing coat in CM 1:4 as specified and directed 4 S&F Premium quality glazed ceramic tile of size 450mm x 300mm thickness 7mm, water absorption between 10% to 20% pasted with spacer,tile adhesive and epoxy grouted with same make as of tile Make Glosstra series of Samany or equivalent in Johnson/Kajaria over including 15 mm thick rendering CM (1:4) and pointed in white or colour cement to match complete all as specified and directed 5 S&F Non-skid ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, (400 X400 mm) as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles15mm thick screed bed or bedding layer CM 1:4 for laying finishes, complete all as specified as directed by Engr-in-Charge 6 Dismantling stone slabsof any description or thickness in floors, apron etc laid bedded and pointed in any mortar complete all as specified 7 M&L for Granite (of any type) work 15 to 17 mm thick (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified 8 M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified 9 M&L, for Machine cut kota stone slab flooring, cills20-25mm thick over cement screed base laid and jointed With grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (single piece of Kota stone to be fixed in stair treads) complete all as specified 10 M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick rendering 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (single piece of Kota stone to be fixed in stair risers) complete all as specified 11 Demolition of Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified 12 M&L for Mirror polishing only on marble / granite / Kota stone / stone work where ever required to give high gloss finish and applying white/colour cement for joints of kota stone complete all as specified and directed by Engr-in-Charge 13 M&L for PCC (1:3:6) type C-2 (using 40mm graded aggregate) 75mm thick as in plinth protection including making grooves complete all as specified 14 Demolition of RCC of any description such chajja, shelves etc and in any position not otherwise specially provided for complete all as specified and directed by Engineer-in-Charge (reinforcement cut as required to facilitate demolition) 15 M&L for reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) as in Slab supported on walls, beams and column in floors, roofs, landings, balconies, deck slabs and in shelves and etc. and setting in mortar complete with joints to match complete all as specified 16 M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified 17 Use and waste of form work to rough finished surfaces of soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick complete all as specified 18 Taking up or down GI tubing 15mm bore pipe complete all as specified. 19 Taking up or down GI tubing 20 mm bore pipe complete all as specified 20 Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings and all other fittings required on walls/ceiling or laying in floors complete including cutting chases in wall, floors etc and their making good in case of concealed pipe work all as specified. bore of pipe 20mm complete all as specified and directed by Engr-in-Charge. 21 Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings and all other fittings requiredon walls/ceiling or laying in floors complete including cutting chases in wall, floors etc and their making good in case of concealed pipe work all as specified. bore of pipe 25 mm complete all as specified and directed by Engr-in-Charge. 22 S&F of 20 mm inner diaCPVC Brass Male/ Female Brass Threaded Adaptor fittings complete all as specified. 23 S&F of 20 mm inner dia CPVC Brass Elbow fittings complete all as specified 24 S&F of 20 mm inner dia CPVC Brass Tfittings complete all as specified 25 S&F in repair Rotational moulded polythylene 1000 ltr capacity waterstorage tank (Cylindrical vertical with closed top) hoisted and fixed in position including 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. & dismantling of old water tank complete all as specified 26 S&F in repairs 20mm gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed 27 S&F in repair 15 mm dia bore fancy type chromium plated long body bib taps cast copper alloy with on/off handle, screwed down, screwed for iron pipe, or for brass ferrule complete all as specified and as directed. 28 S&F Brass CPBasin mixer/wall mixer/sink mixer 15mm bore for mixing hot & cold water screwed down for iron pipe for Wash Hand Basin complete all as specified and directed. 29 S&F in repair 15 mm bore chromium plated Angular stop valve of cast copper alloy screwed down high pressure with on/off handle screwed both ends for iron pipe or for unions and fixed all as specified and directed 30 S&F in repair 15 mm bore chromium plated stop valve of cast copper alloy with long shank and cup (concealed type) ends for iron pipe or for unions and fixed complete all as specified and directed 31 S&F PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality complete all as specified 32 S&F in repair vitreous chinawash basins, size 600x450mm counter type (oval shape), CP Bottle Trap, fancy type CP pillar trap including 32mm waste fittings, waste pipe, chromium plated with long screwed shanks & fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified 33 S&F in repairs vitreous China squatting pan of Orissa pattern of approved make of size 580 mm X 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to anti-syphonage pipe etc including making good to floor complete all as specified 34 S&F in repairs Vitreous China urinals, bowl type (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automaticflushing cistern with brackets flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) (R) complete all as specified 35 S&F urinal spreader of chromium plated for fixing with 15mm dia pipe complete all as specified 36 S&F in repair Vitreous china wash down water closet pan (pedestal pattern), including plastic water closet seat black closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device white excluding fixing bolts, flushing cistern and flush pipe all as specified and directed 37 S&F Health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified. 38 S&F PVC low level cistern of 10 ltrs capacity with top push button inclusive of brackets and PVC bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved make complete all as specified 39 S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and directed 40 S&F in repair 600mm x 450mm bevelled edge mirror 6mm thick of selected quality glass mounted fixed to wall with SS spacer 25mm size complete all as specified. 41 S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified 42 S&F PTMT soap tray any type and fixed to plugs on wall with chromium plated brass screws complete all as specified and directed. 43 S&F Stainless steel fancy type peg set of six and fixed in position with steel screws complete all as specified and directed. 44 Taking down Cast iron pipe and eaves gutters(any size and pattern) including all fittings heads shoes bends swan necks etc including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified 45 Taking down rain water pipe and eaves gutters(any size and pattern) including all fittings heads shoes bends swan necks etc including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified 46 S&F 110 mm bore of pipe PVC (SWR) pipes heavy grade single socket in any length with rubber ring joint fixed to walls with MS clamps complete all as specified and directed 47 S&F 75 mm bore of pipe PVC (SWR) pipes heavy grade single socket in any length with rubber ring joint fixed to walls with MS clamps complete all as specified and directed 48 S&F 110 mm bore of pipe PVC (SWR) pipes heavy grade single socket in any length with rubber ring joint laid in floor complete all as specified and directed 49 S&F 110 mm bore of pipe PVC (SWR) bends heavy grade of any radius / shoefixed to PVC pipes complete all as specified and directed 50 S&F 75 mm bore of pipe PVC (SWR) bends heavy grade of any radius / shoefixed to PVC pipes complete all as specified and directed 51 M&L for PVC (SWR) P’ trap 110mm diaheavy grade completeall as specified. 52 M&L for 75mm dia of long body PVC Floor trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 in repair completeall as specified 53 M&L for PVC (SWR) branch piece, single (single Y), 75 mm bore, (equal or unequal),complete all as specified and directed by Engineer-in-Charge 54 M&L for PVC (SWR) branch piece, single (single Y), 100 mm bore, (equal or unequal), complete all as specified and directed by Engineer-in-Charge 55 M&L for PVC (SWR) junction single,(Single T), 75 mm bore, (equal or unequal), ordinary or inverted (spigot or socket type) or with oval access door as in repairs complete all as specified and directed by Engineer-in-Charge 56 M&L for PVC (SWR) junction single, (Single T), 100 mm bore, (equal or unequal), ordinary or inverted (spigot or socket type) or with oval access door as in repairs complete all as specified and directed by Engineer-in-Charge 57 S&F in repairs PVC (SWR) vent cowl 100 mm complete all as specified and directed 58 S&F Salt-glazed stoneware gully traps 150x 150 mm , square or round mouthed, type P’ complete all as specified and directed 59 Taking down cement plaster from ceilings & brick walls including any type of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed by Engr-in-Charge 60 M&L for rendering 15mm thickin cement mortar in 1:4 on fare face of brick work or concrete surfaces even and smooth without using extra cement & with using integral water proofing compound complete all as specified.(Note : WPC shall be measured and paid for separately) 61 M&L for rendering 10 mm thickin cement mortar (1:6) on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cementcomplete all as specified & directed by Engr-in-Charge 62 M&L for rendering 10 mm thick in cement mortar in 1:3 on ceiling complete all as specified and directed 63 Supply only liquid water proofing compound all as specified 64 M&L for preparation of newly plastered or unplastered surfaces of wall applying two coat of distemper oil emulsion white/tinted with a wall care putty finished surface complete all as specified and directed by Engr-in-Charge 65 M&L for complete removal of existing treatment ofold decorated surfaces of wall by mechanical sander/ brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and filling in depressions to make smooth surface and applying two coat of distemper oil emulsion white/tinted using hand roller complete over two coat of wall care putty all as specified 66 M&L for preparation of newly plastered or unplastered surfaces of ceiling and applying two coat of white washwith a wall care putty finished even and smooth surface by hand roller complete all as specified and directed by Engr-in-Charge 67 M&L for complete removal of existing treatment ofold decorated surfaces of ceiling by mechanical sander/ brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and filling in depressions to make smooth surface and applying two coat of white wash over coat of wall care putty finished even and smooth surface by hand roller complete all as specified and directed by Engr-in-Charge 68 M&L for preparation of newly plastered or unplastered surfaces of wall, soffits/ facia of chajja/ roof slab for applying Two coat of Acrylic Smooth exterior paint of required shade over and including one coat of exterior primer and one coat of exterior wall care putty complete all as specified 69 M&L for complete removal of existing treatment ofold decorated surfaces of wall by mechanical sander/ brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots including filling depression of scraped surface with wall putty two coats 1.5 mm thick each and Finishing walls with Two coat of Acrylic Smooth exterior paint of required shade over and including one coat of exterior primer complete all as specified 70 Dismantling of brickwork built in cement mortar of any description complete all as specified and directed by Engineer-in-Charge 71 M&L for brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc. complete all as specified and directed by Engineer-in-Charge 72 Dismantling of stone slab and tilesin any description in aprons and floors and removal from the site to a distance n.exc 500 metres complete all asspecified and directed. 73 M&L for 100 mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) in sub base, floors etc complete all as specified and directed 74 M&L for Machine pressed Precast cement concrete interlocking coloured ( glossy finished / rubberised paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with and including 40mm thick sand cushioning complete all as specified and directed by Engr-in-Charge 75 Taking downchowkats or frames n.exc 1.5 sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed. 76 Taking downchowkats or frames exc 1.5 sqm but n. exc 4 sqmeach with shutters (without taking of shutters from the frames) complete all as specified and directed. 77 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45*85 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and screw withdrawal strength of 2200 N (Face)and 1100N (edge), minimum compressive strength 58 N/ mm ², modules of elasticity 900 N/mm ² and resistance of spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note:-(i) Density is not less than 650 (ii) Variation in profile size of frame ±5mm is allowed and contractors quoted rate is deemed to include the same 78 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65*100 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and screw withdrawal strength of 2200 N (Face)and 1100N (edge), minimum compressive strength 58 N/ mm ² ,modules of elasticity 900 N/mm ² and resistance of spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed.Note:- (i) Density is not less than 650(ii) Variation in profile size of frame ±5mm is allowed and contractors quoted rate is deemed to include the same 79 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65*125 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and screw withdrawal strength of 2200 N (Face)and 1100N (edge), minimum compressive strength 58 N/ mm ² ,modules of elasticity 900 N/mm ² and resistance of spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed.Note:- (i) Density is not less than 650(ii) Variation in profile size of frame ±5mm is allowed and contractors quoted rate is deemed to include the same 80 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 81 S&F 100 mm long, Stainless Steel hinges with stainless steel screws complete all as specified and directed 82 S&F Stainless Steel barrel tower bolts, 200 mm long of extruded section complete all as specified and directed. 83 S&F Stainless Steel sliding door boltof length 250mm with hasp and staple (bolt type) andfixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed 84 S&F 140 mm floor door stopper of Stainless Steel body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 85 M&L for preparation of new or previously untreatedwood or wooden based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed 86 S&F stainless Steel handle 150 mm size complete all as specified and directed 87 M&L for Aluminium Powder coating section for door/window / Ventilators/partition etc frames & shutters including joining cleat, mullion, grills etc. sliding/ openable type complete of standard sections all as specified and asdirected by Engr-in-Charge. (Aluminium section shall be of make Jindal/Hindalco/ Indalco) 88 S&F aluminium door lock 7 lever vertical type brass body 100mm long with duplicate key complete all as specified. Make : Godrej 89 S&F of door closer hydraulically regulated aluminium (dia cast) body designation No 3 universal type suitable for door shutter of weight between 61 to 80Kg of approved make having ISI mark all as specified. 90 M&L for anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified 91 Providing and fixing factory made uPVC white colour Sliding window Three track area notexceeding 2 sqm made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) 92 S&F 5mm Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified 93 S&F factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both havingwall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame andmullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). 94 S&F factory made uPVC white colour Sliding window Three track area exceeding 2 sqm but n.exc 4 sqmmade of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) 95 S&F Sheet glass of 4.8 mm, ordinary quality and glazing but exc 0.5 sqm in each pane with oil putty in square required complete all as specified and directed 96 S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge 97 Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying cables/poles foundation / stay assembly, etc. n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed 98 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified 99 Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified 100 Demolition and breaking up drain pipes 150mm internal dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified 101 M&L for 150mm bore RCC NP2 drain pipes laid in trenches and jointed with collars all as specified and directed 102 M&L for 150mm bore Concrete bed (PCC 1:3:6 type C2)to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified 103 S&F stainless steel plate racks of size 900x600mmx250mm and thickness of SS strip of 1 mm fixed on wall etc complete all as specified 104 S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified 105 S&F in repair waste fittings 32 mmbrass chromium plated for glazed ware sinks, basins etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge 106 S&F Armstrong false ceiling with board of size 600x600x12 mm thick including armstrong grid work all as per manufacturers instruction etc complete all as specified and directed 107 S&F hollow PVC wall lining interlocking type 7mm thick plain/coloured /wood grain fitted in to the wall with PVC rawl plug and steel screws including fillets on joints as per manufacturers instruction etc complete all as specified and directed by Engineer-in-Charge. Note:- If any minor electric fittings and fixtures disturbed there will be match and fixed as existing 108 M&L for 3 mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters) in Squares n.exc 0.5 sqm each complete all as specified and directedby Engr-in-Charge 109 Dismantling of boarding any description fixed in any position with nails complete all as specified 110 M&L for 18/19 mm thick both sidepre-laminated (One side decorative and one side plain) particle board exterior grade fixed with screws to timber frame work complete all as specified 111 S&F in repair Framed work such as grills, gratings cooler stand, ladder etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified 112 M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying a coat of red oxide zinc chrome primer andtwo coats of synthetic enamel paint (for steel surfaces) including preparation of surface complete all as specified. 113 S&F in repair MS powder coated decorative drapery rod (colour as approved) of 20mm dia approved pattern & design including decorative knobs (wall side and free side) & powder coated mild steel flat iron brackets fixed with steel screws & PVC rawl plugs/grips complete all as specified 114 Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material upto a distance n.exc 100m where directed, all as specified. 115 Demolition of mud in roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m, where directed all as specified 116 M&L 50mm thick PCC 1:2:4 type B0 (12.5mm graded aggregate) with WPCin roof complete all as specified and directedNote : WPC will be measured and paid separately. (WPC will conforms to IS: 2645-2003) 117 M&L for Roof Treatmentas specified below and as directed :(a) Cleaning, washing of surface completely with high speed water jet. Surface should be free from any loose paint, dust or grease.(b)Rendering 10 mm thick in cement plaster 1:4 withWPC on roof(b)All cracks upto 3mm at corner joints, channels and parapets should be treated with crack seal and bigger cracks, damaged portions and hollow areas must be repaired with polymer modified cement mortars.(c)Applying one coat of PrimeSeal/ Epoxy Primer/ShaliUrethane BTD White diluted with potable water in the ratio of 1:1 and apply @ 0.40 kg/ sqm (0.20 kg BTD+0.20 Kg water)(d)Laying polyster reinforced fiber net/50 gsm Geotextile mesh, upto 300 mm on walls.(e)Applying three coat of HydroShield PUD microfibre reinforced UV resistent polyurethane (solid content 68% ) / Damp Proof ultra UVStable fibre reinforced elastomeric liquid waterproofing membrane formulated with PU hybrid polymers (Solid content 55%)/ SmartCare PU Magnum elastomeric waterproofing coating based on hydrophobic polyurethane (solid content 85%)/Single Component Elastomeric Liquid Membrane ShaliUrethane BTD White/coloured(Elongation 400% ± 50, Solid Contents > 80% & Specific Gravity @ 30 OC 1.5 ± 0.03) @ total 2.00 Kg per sqm in two coats for maintaining thickness of 1.5mm,with paint brush/ roller upto 300 mm on walls.(f)The complete treatment to be carried out by authorised applicator of waterproofing manufacturer.Make : DrFixit/ Asian/STPNote : (i)The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer in Charge.(ii)The plan area of floor shall be considered for payment . 118 Supply for Pipe Supporting Clamping - Single Pipe of PVC dia 110 mm (4) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3):Pipe Support Clamping made of:1. Profile Bracket having Wall Distance 75 mm (3) made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 HexFlange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923.2. Continuous Slotted C Channel with ribs to be used of size 250 mm (10) made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm.3. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated.Hotdip Galvanizing: As per IS 2629 (1985)- 610 grams/m² (> 85 microns).Material Grade IS 1079 used as per MTC confirms to EN 10204 3.1.Material Qty. for one unit: 1. Profile Bracket Wall distance 75 mm (3) - 2 Nos. 2.Continuous Slotted C Channel of Size 250 mm (10) - 1 No.; 3. U Bolt Rubber sleeve mounted for 110 mm (4) PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2) - 4 nos.Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Bhatinda Zone Technical Drawing (TD) of Factory Made Pipe Supporting System. REF DRG NO. BTD-916.Make: Shaivi or equivalent as approved by GE. 119 Supply for Pipe Supporting Clamping - Single Pipe of PVC dia 75 mm (3) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3):Pipe Support Clamping made of:1. Profile Bracket having Wall Distance 75 mm (3) made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 HexFlange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923.2. Continuous Slotted C Channel with ribs to be used of size 250 mm (10) made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm.3. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated.Hotdip Galvanizing: As per IS 2629 (1985)- 610 grams/m² (> 85 microns).Material Grade IS 1079 used as per MTC confirms to EN 10204 3.1.Material Qty. for one unit: 1. Profile Bracket Wall distance 75 mm (3) - 2 Nos. 2.Continuous Slotted C Channel of Size 250 mm (10) - 1 No.; 3. U Bolt Rubber sleeve mounted for 110 mm (4) PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2) - 4 nos.Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Bhatinda Zone Technical Drawing (TD) of Factory Made Pipe Supporting System. REF DRG NO. BTD-916.Make: Shaivi or equivalent as approved by GE. 120 Taking down point wiring complete including fixture and fittings and making good to disturbed area all as specified and directed by Engr-in-Charge. 121 Taking downMCB, DB any Type including MCBs and making good to the disturbed walls and surface area etc all as specified and directed by Engr-in-Charge. 122 Taking down submain wiring any type with earthing cable and making good to disturbed area all as specified and directed by Engr-in-Charge. 123 M&L in replacement modular point wiring complete with ISI marked 1.5 sqmm single core PVC insulated unsheathed cable 1100V grade FRLS with multi-stranded copper conductor drawn through concealed in wall/ceiling with PVC rigid concealed conduit suitable size with all accessories such as bend, reducers, MS hooks, ceiling rose, galvanised steel pressed modular terminal boxes of suitable sizes for mounting of switches, sockets, fan regulator etc covered with plastic laminated modular top cover sheet of required colour fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer includingfixing and 1.5 sqmm copper conductor as earth continuity to connect common earth dolly and including taking down old unserviceable wire any type and making good disturbed surfaces of walls as necessity for One light point/Fan point/Exhaust point / bell point controlled byone way switch completed all as specified and directed 124 All as per Srl Item No. 123 here-in-before but one three pin socket out let 5 amps on the same board with other switches 125 All as per Srl Item No. 123 here-in-before but one 3 pin, 5A switch socket outlet point on independent board 126 All as per Srl Item No. 123 here-in-before but with 2.5 sqmm cable for 1No 16 amps socket outlet point on independent board including 2.5 sqmm PVC insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor. 127 M&L for ceiling rose 3 terminal / PVC / polycarbonate isolated body andincluding taking down old unserviceable ceiling rose all as specified and directed by Engr-in-Charge 128 S&Fin replacement of Modular switch 1 way 6 amps one moduleincluding taking down unserviceable switch any type all as specified and directed 129 S&Fin replacement of Modular socket 6A 2/3 pin combined 2 moduleincluding taking down unserviceable socket any type all as specified and directed 130 S&Fin replacement of Modular switch 1 way 16 amps 1 moduleincluding taking down unserviceable switch any type all as specified and directed 131 S&Fin replacement of Modular socket 6A / 16A - 2/3 pin combined 2 moduleincluding taking down unserviceable socket any type all as specified and directed 132 S&FPVC Lamp holder suitable for LED 5 to 20 watt bulb complete all as specified and directed 133 S&F of Rechargeable LED bulb 1x10 Watt lamp having luminous efficacy warranty 2 year all as per specification & directed by Engr-in-Charge. Make-Havells/Philips/Bajaj 134 S&F of Rechargeable LED tube light fitting 20W, (4 feet long) 230 V, surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver and including connections up with copper conductor wire with suitable size as per specification and directed by Engineer-in-Charge. Note:- LED tube light must be rechargeable and minimum 4 hours battery backup 135 S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as directed by Engr-in-Charge with following specification:- (a) Lumen efficacy of luminaire should be more than 100 Lumen per watt. (b) Voltage operating range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP20. (g) CRCA pre coated housing. (h) LED Driver of the make as of the luminaire. (l) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer. (m) Inbuilt Surge protection device for 4 kV. 136 S&F LED street light 25 watt luminaries comprising of epoxy powder coated housing, enclosed with glass cover including 40mm GI Bracket and fixing arrangement in road light, security light etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable 1.5 sqmm with suitable size and including taking down defective unserviceable street light any size as per specification & directed by Engr-in-Charge. Make: Havells/ Philips/ Bajaj 137 Taking down existing serviceable ceiling fan / Exhaust Fan complete all as specified and directed byEngr-in-ChargeNote : Old unserviceable ceiling fan / Exhaust Fan will be Deposited in E/M Yard Office 138 S&F Energy efficient Ceiling fan complete with blades, down rods, electronic type regulator & accessories, 230 V,1200mm sweep,BEE, 5 star rated with brushless direct current motor (BLDC)includingwriting of MES number (Black, Roman, Italic or Indian) n.exc 30cm height complete all as specified and directed 139 S&F in replacement Exhaust fan steel body AC single Phase 230 Volt of size 300 mm Sweep with blades and frame and Louvers complete all as specified and directed by Engr-in-Charge . Note:- Electric Connection 03 Core PVC Sheatehed round of copper cable size 23/076 of suitable length shall be provided by contractor. 140 Taking down serviceable Geyser complete with accessories any size all as specified and directed by Engr-in-Charge.Note : Old unserviceable Gyser will be Deposited in E/M Yard Office 141 Supplying and fixing and commissioning of electric water heater (Gyser) storage type ABS body of capacity 25 ltrs, BEE approved 5 star rating, 230V,single Phase, AC supply inner tank made out of heavy duty stainless steel sheet (Designed with single weld line, factory tested with hydraulic pressure as per latest IS code) with glass lined quoting complete with all accessories such as safety valve thermostat NRV, connection piece PVC connectionfor hot and cold water 3 core PVC insulated PVC sheathed copper conductor flexible cable including 15 Amp plug suitable for existing socket and fixing material, 04 Nos nut bolt grouting in wall in PCC(1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and directed 142 M&L for Stop valves, cast copper alloy, screwed down, high pressure, fancy type, chromium plated 15 mm bore of pipe,screwed both ends for iron pipe and fixed complete all as specified 143 Supply and laying of CPVC Pipe outer dia 16mmISI Marked, including tube fittings Viz Tees Socket bends elbows, union nipple etc screwed and socketed joint fixed on wall / trenches with all fitting complete all as specified. 144 S&F sheet metal enclosure for DBs SPN 230 volts 12 waydouble door complete all as specified and directed .. 145 S&F sheet metal enclosure for DBs SPN 230 volts 8 waydouble door complete all as specified and directed. 146 S&F in replacement (concealed flush to wall) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 250 Amp rated bus bar) VTPN, 4 Way, suitable for mounting MCCB/MCB, conforming to IS-13032, DB shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-42 protection class, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessity complete all as specified and directed by Engineer-in-charge.Note :- MCCB/MCB shall be measured and paid separately under appropriate item of BOQ 147 S&F MCCB 4 pole, 415 V. adjustable type, 100 Amp with breaking capacity 16 KA and including taking down old unserviceable items and as complete all as specified and directed 148 S&F 10 KA B curve miniature circuit breaker (MCB) SPN and current carrying capacity 63 AMP, in the MCB DB Complete with connection complete all as specified and directed by Engr-in-Charge. 149 S&F amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 AMP, in the MCB DB complete with connection testing and commissioning all as specified 150 S&F amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of SPN and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioning all as specified 151 S&F 240V, 10 KA B curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed 152 S&F Socket Residual Current Device (SRCD) with steel enclosure includingMCB,SPN 20 Amps,240 V,AC supply & plug top complete all as specified and directed. 153 M&L for wiring for circuit sub main wiring with two single core PVC FRLSinsulatedcopper conductor 2x4 sqmm and same 1x4 sqmm for continuous earth wire drawn in to concealed PVC conduit complete all as specified and directed by Engr-in-Charge. Note: Cost of PVC conduit, conduit accessories and earth wire including in sub main wiring 154 S&Fsub main wiring with two runs of single core PVC, FRLS sheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated FRLS copper wire 6 Sqmm for continuous earth wire drawn into and including concealed conduitof suitable size not less than 20mm dia complete all as specified and directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuity conductor , conduit with accessories shall be measured as one length) 155 M&L for Earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead ofGI wire 4 mm dia (8 SWG) by means of bolts, nuts and washers of the earth wire galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia GI light grade with funnel & wiremesh, PCC chamber in cement concrete (1:2:4) type B1 including 40mm thick pre-cast RCC (1:2:4) type B0 cover and 40x40x6mm angle iron frame on top of pit cover and excavation & earth work completeall as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009. complete all as specified and directed by Engr-in-charge.Notes :- (i) GI wire upto earth test point/equipment is included in this item.(ii) Outer edge of earth pit chamber shall be 1 metre away from the outer edge of PCC chamber. 156 M&L for Laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sqmm 4 core in trenches/floors/wall and under road including connecting with suitable aluminium lugs and including taking up defective unserviceable cable of the any sizes all as specified and directed by Engr-in-Charge. Note: Earth work, Sand cushioning, GI pipe and cable cover for protection to be measured and paid separately 157 Supply and spread dry fine aggregate sand in trenches for cable cushioning all as specified onboth top and bottom of cable including ramming all all as specified and directed by Engr-in-Charge. 158 M&L for laying factory made un reinforced precast concrete cable cover ISI marked class LV type 2 flat size 300 mmx180 mmx40 mm completelaid in trenches of across the cable protection all as specified and directed 159 S&F Air termination single pointed aluminium rod 12 mm dia and 300mm long fixing on top of building complete all as specified and directed 160 S&F Aluminium strip 25x3.15 mm with saddles and fixing screws etc for roof conductors above ground (top of building and down upto test point complete all as specified and directed 161 M&L for test point terminal block made of gun metal of phosphorus bronze size 75x75x25 mm, drilled and screwed including 3 nos 8 mm dia 25 mm long hex head screw of brass/gun metal complete all as specified and directed 162 Supply and installation, commissioning of desert cooler electric driven (single phase), having nominal air flow capacity of 6000 CuM per hour (or nearest size).(*Steel body)deep galvanised steel thickness 1mm body and 1mm removal side and back panel single phase 230 volts,with submersible pump of suitable size (Maximum power consumption 250 volts) ISI marker(with float valve of 15mm dia, stop valve of 15 mm dia, nut washer PVC connections of 15mm dia to air cooler complete all as specified.Note : (a) : Sufficient length of 3 core PVE sheathed round copper cable size 23/076 to enable fixing in to plug point shall be provided by contractor. (b)Arrangement of power connections and water connections to the desert cooler will be included in installation.(c) No extra payment shall be made to float valve, stop valve, nut, washer PVC connection, leak proof joints etc and making connection from GI pipe 15 mm dia to air cooler in this regards) union for GI pipe ball valves brass complete including electric connection 163 M&L for cutting existing pipe any size for branch connections with provn of Tee 50mmx50mm x25 mm and accessories complete all as specified and directed 164 M&L for laying steel water Tubeing, 20 mm dia ISI Marked, “Medium grade galvanised, including tube fittings Viz Tees Socket bends elbows, union nipple etc screwed and socketed joint laid in trenches/under road with all fitting complete all as specified 165 M&L forlaying steel water Tubeing, 25 mm dia ISI Marked, Medium grade galvanised, laid in trenches/under road with all fitting including taking down old Unserviceable pipe any type complete all as specified 166 M&L for Gun metal gate valve/Stop valves, cast copper alloy, screwed down, high pressure, 25 mm bore of pipe,screwed both ends for iron pipe and fixed complete all as specified 167 M&L for Gun metal gate valve/Stop valves, cast copper alloy, screwed down, high pressure, 20 mm bore of pipe,screwed both ends for iron pipe and fixed complete all as specified 168 Supply and installation air cooled split air conditioners unit indoor/outdoor complete with remote control unit and within built and with remote control unit and within built Heating and Cooling arrangement electric driven single phase of capacity 1.5 TR, BEE 3 star rated complete all as specified and directed 169 S&F voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input voltage variation between 130V to 250 V with output voltage stabilizer at 230 V with accuracy of ±2.5% and of capacity 5KVAcomplete all as specifiedNote :-A Sum of Rs. 55,314.00 will be deducted on account of credit for dismantling/ demolished/ taking down material. Please refer detail on srl page No. 49 (Schedule of credit) of Tender Documents.
