Tender For Repair Re Canning Painting And Polishing To Wooden And Steel Furniture Items At Af Stn Jammu Under Ge Af Jammu; 1 Taking down worned out/unsv components of the following wooden/steel furniture items, Supply and fix new component without any crack/any defects as pe shape and size specified on respective drawings and as directed by Engineer-in-Charge.WOODEN FURNITURE:-CHAIR DINING (FD-203/279) 2 Replacement of u/s Rear Legs of chair dining with new rear legs of seansoned hard wood free from cracks and knots, shape and size as shown on drawings 3 Descrption all as per ser item No 1(1.01) above but Front Legs 4 Descrption all as per ser item No 1(1.01)above but Side rail with holes for weaving (spacing of holes shall be as per old one) 5 Descrption all as per ser item No 1(1.01)above but Front/back rail with holes for weaving (spacing of holes shall be as per old one) 6 Descrption all as per ser item No 1(1.01) above but Bottom stiffener 7 Descrption all as per ser item No 1(1.01) above but Back stiffener 8 Provn of four Nos of wooden tringular bracket of size 75mm x 75mm to each chair made out 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge 9 PVC/Rubber Shoe as per sample approved 10 Re-canning of Chair dining as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane.Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge. 11 CHAIR DINING MAP (FD/MAP-II/05) 12 Replacement of u/s Rear Legs of chair dininng with new rear legs of seansoned hard wood free from cracks and knots, shape and size as shown on drawings 13 Descrption all as per ser item No 2(2.01) above but Front Legs 14 Descrption all as per ser item No 2(2.01) above but Bottom stiffener 15 Descrption all as per ser item No 2(2.01) above but Back stiffener 16 PVC/Rubber Shoe as per sample approved 17 Replacement of u/s PVC Seat with new PVC seat 4mm thick of PPCP material and weight not less than 0.50 kg with perforated holes shall be fixed in side the frame of seat with proper screws , PVC sheet of superior quality as shown in drawing and directed by Engineer-in-charge. 18 CHAIR WRITING WITH CUSHION (FD-1107) 19 Replacement of u/s Rear Legs of chair writing with cushion new rear legs of seansoned hard wood free from cracks and knots, shape and size as shown on drawings 20 Descrption all as per ser item No 3(3.01) above but Front Legs 21 Descrption all as per ser item No 3(3.01) above but side rail 22 Descrption all as per ser item No 3(3.01) above but front/back rail 23 Descrption all as per ser item No 3(3.01) above but Bottom stiffener 24 Descrption all as per ser item No 3(3.01) above but Back stiffener 25 Descrption all as per ser item No 3(3.01) above but Arm rest 26 Provn of one Nos of bottom cushion seat fixed on a frame with cover of size as per drawing shall be fixed with screws on chair as directed by Engineer-in-Charge 27 PVC/Rubber Shoe as per sample approved 28 Provn of one Nos of back cushion seat fixed on a frame with cover of size as per drawing shall be fixed with screws on chair as directed by Engineer-in-Charge 29 CHAIR DINING MAP (OFFICER) (FD/MAP-II/04) 30 Replacement of u/s Rear Legs of chair dining with new rear legs of seansoned hard wood free from cracks and knots, shape and size as shown on drawings 31 Descrption all as per ser item No 4(4.01) above but Front Legs 32 Descrption all as per ser item No 4(4.01) above but side rails 33 Descrption all as per ser item No 4(4.01) above but front rails 34 Descrption all as per ser item No 4(4.01) above but stifeners 35 Descrption all as per ser item No 4(4.01) above but teak wood stopper for support of the cushion and seat ply 36 Descrption all as per ser item No 4(4.01) above but 75mm thick 40 density cushion of approved from (Kurlon/Sleepwell) covered with approved tapestry cloth shall be fixed over 12mm thick ply as spacified in drawing 37 PVC Rubber Shoe as per sample approved 38 SOFA SET 4 Seater (FD-281/373) 39 Replacement of arms made out of teak wood duly french polish as per drawing complete. 40 Replacement of front legs of sofa set made out of teakwood duly french polish as per drawing complete. 41 Replacement of rear legs of sofa set made out of teakwood duly french polish as per drawing complete. 42 PVC Rubber Shoe as per sample approved 43 Foam cushion for sofa set size 525x525x100mm, 40 density, Make-Sleepwell duly covered with best quality tapestry cloth as approved by Engineer-in-Charge complete all as directed and specifiedNote:-Rate of tapestry cloth shall not be less than Rs 250/- per RM 44 SOFA SET 5 Seater (FD-281/373) 45 Replacement of arms made out of teak wood duly french polish as per drawing complete. 46 Replacement of front legs of sofa set made out of teakwood duly french polish as per drawing complete. 47 Replacement of rear legs of sofa set made out of teakwood duly french polish as per drawing complete. 48 PVC Rubber Shoe as per sample approved 49 Foam cushion for sofa set size 525x525x100mm, 40 density, Make-Sleepwell duly covered with best quality tapestry cloth as approved by Engineer-in-Charge complete all as directed and specifiedNote:-Rate of tapestry cloth shall not be less than Rs 250/- per RM 50 BED PLYTOP WOODEN (FD 246/247) 51 Head rest as shown on drawing 52 Foot Rest as shown on drawing 53 Long rail made of Ist class hard wood 54 Short rail made of Ist class hard wood 55 Stiffener made of Ist class hard wood 56 Replacement of unsv legs with new seasoned teak wood 57 Right angled MS bracket 200mm long x 25mm wide x 3mm thick duly fixed with screw 58 12mm thick BWR Ply wood top in one piece 59 CHAIR WRITING (FD-261/280) 60 Rear legs 61 Front Legs 62 Side rail with holes for weaving (spacing of holes shall be as per old one) 63 Front/back rail with holes for weaving (spacing of holes shall be as per old one) 64 Bottom stiffener 65 Back stiffener 66 Arm rest 67 Provn of four Nos of wooden tringular bracket of size 75mm x 75mm to each chair made out 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge 68 PVC/Rubber Shoe as per sample approved 69 Re-canning of Chair Writing as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane.Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge. 70 CHAIR EASY (FD-229) 71 Rear Leg 72 Front Leg 73 Side Rail 74 Front/Back Rail 75 Back Stiffener 76 Bottom Stiffner 77 Arms rest 78 PVC/Rubber Shoe as per sample approved 79 Re-canning of Chair easy as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane.Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge. 80 TEAPOY (FD-278/382) 81 Legs 82 Long rail 83 Short rail 84 Side stiffener 85 Centre stiffener 86 Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge.Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed. 87 PVC/Rubber Shoe as per sample approved 88 Provn of eight Nos of wooden tringular bracket of size 75mm x 75mm to each teapoy made out 30mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge 89 PEG TABLE (FD-236/277/384) 90 Legs 91 Long rail 92 Short rail 93 Side stiffener 94 Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge.Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed. 95 PVC/Rubber Shoe as per sample approved 96 TABLE WRITING (FD-275) 97 Legs 98 Long rail 99 Short rail 100 Drawer made out prelaminated MDF board and 6mm thick commercial ply at bottom and fitted with one 100mm chromium plated handle 101 Bottom centre stiffener 102 Bottom side stiffener. 103 Provn of six Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge 104 Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge.Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed. 105 PVC/Rubber Shoe as per sample approved 106 TABLE 900mm x 600mm with drawer and without drawer (FD-283/284) 107 Legs 108 Long Rail 109 Short Rail 110 Bottom Side stiffener 111 Bottom Centre stiffener 112 Drawer made out prelaminated MDF board and 6mm thick commercial ply at bottom and fitted with one 100mm chromium plated handle 113 Provn of six Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge 114 Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge.Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed. 115 PVC/Rubber Shoe as per sample approved 116 TABLE DINING 6/8 PERSON( FD-239/273,376,FD-30) 117 Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge.Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed. 118 Legs 119 Long rail 120 Short rail 121 Stiffener 122 Provn of eight Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 40mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge 123 PVC/Rubber Shoe as per sample approved 124 TABLE DRESSING LADIES (FD-251/378/395) 125 5mm thick Mirror of size 365mmx1220mm with Back ply of 6mm thick commercial plywood and wooden frame of existing shape & size. Make- Saint Gobin/Gold plus 126 Sliding glass shutter of 3mm thick as per existing. 127 Drawer of 6 mm thick ply wood commercial with 18mm pre-laminated MDF board as per existing shape and size 128 Knob as per sample approved 129 TABLE BED SIDE (FD-248 /276) 130 Top 18/19mm thick both side prelaminated MDF board fixed with PVC edge band tape 131 Side made of 18/19mm thick both side prelaminated MDF board fixed with PVC edge band tape 132 Shelf made of 18/19mm thick both side prelaminated MDF board fixed with PVC edge band tape 133 Bottom made of 18/19mm thick both side prelaminated MDF board fixed with PVC edge band tape 134 Back shall be made of 6mm thick ply wood commercialas per existing shape and size andshown in drgs and directed 135 Leg frame with 4 Nos leg and stiffener as per drawing made Ist class hard wood (teak) duly french polished. 136 TABLE CENTRE (FD-274/375) 137 Legs 138 Long rail 139 Short rail 140 Side stiffener 141 Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge.Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed. 142 PVC/Rubber Shoe as per sample approved 143 TABLE DRESSING GENTS(FD-230/379) 144 Looking glass complete with frame and back ply. As per drawing Make- Saint Gobin/ Gold Plus 145 Drawer of 6 mm thick ply wood commercial with front 18mm pre-laminated MDF board and Knob as per existing shape and size 146 Provision and replacement of CP knobs 32mm in brown colour as per sample 147 Side board (FD-26,FD-371,& FD-372) 148 Provision and replacement of sides of the side prelaminated particle board 18mmboard veneered 149 Provision and replacement of old/UNSV drawer with teak wood sides andpre-laminated particle board 18mm thick on front and plywood 6mm thick commercial quality at the bottom.Make :- Kitply, Greenply, Archidply 150 Provision and replacement of doors of the side board made of pre-laminated board 18mm thick with teakwoodedgingdoor fixed with piano hinges.Make :- Kitply, Greenply, Archidply 151 Provision and replacement of top made out of pre-laminated particle board 18mm thick. 152 Provision and replacementof bottom frame made of18mm thick teak wood and fixed with screws all as shown on drawings. 153 Provisionand replacement of hard wood legs of side board all as per drawings. 154 Provision and replacement of CP knobs 32mm in brown colour as per sample 155 Table Bed side MAP (FD/E6/MAP/15(R) 156 Provision and replacement of drawer on 18mm Thick Pre laminated Partical board with telescopic channel as per drawings . 157 Provision and replacement of18mm Thick Pre laminated Partical board top with PVC edging fixed to frame (25mm projection on three spaces) as per drawings. 158 Provision and replacement of18mm MS square pipe(500mmx450mm) (18 gauge) black powder coatedas per drawings. 159 Provision and replacement ofhandles as per drawings and sample apporoved by Engr-in-charge. 160 Table Dressing Ladies MAP (FD/MAP-II/07) 161 5mm thick electro copper plated mirror shall be fixed/replace over 6mm thick plywood back. 162 Replacement of sides with new sides of 18mm thick pre-laminated MDF board. 163 Replacement of sides with new top of 18mm thick pre-laminated MDF board. 164 Replacement of sides with new back of 18mm thick pre-laminated MDF board. 165 Replacement of sides with new front of 18mm thick pre-laminated MDF board. 166 Replacement of bottom of side units with 12mm thick commercial plywood. 167 Side and back drawers to be repaired with 12mm thick pre-laminated MDF board. 168 Replacement of old/unsv knobs of drawers. 169 Replacement of vertical hardwood members of size 45mm x 30mm. 170 Replacement of horizontal support of size 30mm x 20mm. 171 Stool of dressing table - Replacement of heavy duty revolving nylon double wheels at base. 172 Replacement of seat of the with 75mm thick foam of 40 density coverd with tapestry cloth as approved by Engr-in-charge. 173 Mirror Dressing Gents (FD/E6/MAP/16) 174 Replacement of looking mirror of size 5mm thick fixed inside the teakwood frame made out of the 38mm x 25mm section as per drawing. 175 Replacement of teak wood beading of size 6mm thick around the edges of shutter and drawer. 176 Replacement of glass shelves of 5mm thickness to be fixed inside the box as shown in drawing. 177 Replacement of the old hasp & stapples. 178 Replacement of old/UNSV magnetic catchers. 179 Table card 900 x 900mm (FD-88,352) 180 Top of the table made out of partical board 18mm thick with 1mm pre-laminated exterior grade with teakwood beading all-around duly polished as per drawing. 181 Legs of table as per drawing 182 Long rail of table as per drawing 183 Stiffeners H type of the table as per drawing 184 PVC/Rubber Shoe as per sample approved 185 Table Dining 120 x 90cm (FD/MAP-II/03) 186 Replacement of top of table with 18mm thick BWR plywood of grade A with 1mm thick laminated sheet pasted over the ply with suitable screws from under neath, edges of top shall be coverd with 6mm thick teak wood as per drawing. 187 Replacement of wooden corner brackets made to shape of size 100mm x 100mm x35mm thick. 188 Replacement of long rails as per drawing 189 Replacement of short rails as per drawing 190 Replacement of legs as per drawing 191 PVC/Rubber Shoe as per sample approved 192 Polishing of Wooden Furniture Item : All wooden and steel surfaces of the following furniture itemswheather exposed to view or not when placed in position shall be polised with high gloss french polish and painted with high glossy paintto be finished as directed by Engineer-in-Charge duly preparation of surface with emery paper and applying putty as and where required:- 193 CHAIR DINING (FD-203/279) 194 CHAIR DINING MAP (FD/MAP-II/05) 195 CHAIR WRITING WITH CUSHION (FD-1107) 196 CHAIR DINING MAP (OFFICERS) (FD/MAP-II/04) 197 Sofa four seater (FD-281) 198 Sofa 5 seater (FD-281/373) 199 BED PLYTOP WOODEN (FD 246/247) 200 CHAIR WRITING (FD-261/280) 201 CHAIR EASY (FD-229) 202 TEAPOY (FD-278/382) 203 PEG TABLE (FD-236/277/384) 204 TABLE WRITING (FD-275) 205 TABLE 900mm x 600mm WITH DRAWER and WITHOUT DRAWER (FD-283/284) 206 TABLE DINING 06/08 PERSON( FD-239/273) 207 TABLE BED SIDE (FD-248 /276) 208 TABLE CENTRE (FD-274/375) 209 TABLE DRESSING LADIES (FD-251/378/395) 210 TABLE DRESSING GENTS(FD-230/379) 211 Side board (FD-26,FD-371,& FD-372) 212 Table Bed side MAP 213 Table Dressing Ladies MAP (FD/MAP-II/07) 214 Mirror Dressing Gents (FD/E6/MAP/16) 215 Table card 900 x 900mm (FD-88,352) 216 Table Dining 120 x 90cm (FD/MAP-II/03) 217 STEEL FURNITURECharpoy GI Pipe (FD-220) 218 3 way Galvanized Iron Elbow 32 mm dia. Note weight of each elbow shall not be less than 450 gm 219 Galvanized iron check nut 32mm dia.Note:-weight of each check nut shall not be less than 125gm 220 Long rail of 32 mm dia galvanized iron pipe medium grade incl threading at both ends as directed 221 Short rail converted out of retrieved Long rail, Item No 1(c)above incl cutting, threading as required and directed 222 Leg converted out of retrieved Short rail, Item No 1(d) above incl cutting, threading as required and and directed 223 Provn of Two Nos MS cleat as shown on drg to hold the MNF set and one MS plate at the bottom to each Leg converted out of retrieved Short rail 224 Provision oftwo no 6mm thick x 50 mm width MS flat strip of 900 mm long by drilling four nos screw to long rail. All as specifed. 225 12mm thick ply wood top BWR Grade ISI Marked of size 1950mm x 900mm (Single piece) Make Kitply, centurey and equalent including replacement of old plywood or newar. 226 BED HARD STEEL (FD/E6/MAP/08(R) 227 12mm thick ply wood top of size 1950mm x 900mm (Single piece)BWR Grade ISI Mark with MS screws, complete all as specified Make Kitply, centurey and equalent 228 Replacement of 18mm thick prelaminated particle board at head side of the bed as specified 229 Replacement of 18mm thick prelaminated particle board at foot side of the bed as specified 230 PVC shoes at the bottom of leg. 231 CHAIR COMPUTER (FD/E6/MAP/01) 232 Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size covered with tapestry cloth as approved along with PVC liping all round, complete all as specified 233 All as per item No 28.01 here-in-before but for back frame 234 Replacement of Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified 235 Replacement of Pedestal assembly complete 236 Replacement of Twin wheels coasters (set of five) press fitted at the bottom of leg. 237 CHAIR WRITING MAP (FD/E6/MAP/12) 238 Replacement of exising tapestry of seat frame with newtapestry cloth of seat frame approved by Engr-in-charge with PVC liping all round complete all as specified and directed by Engr -in charge Note- Cost of tapestry not less than Rs 250/ RM. 239 All as per item No29.01above but for back frame 240 Replacement of Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified 241 Replacement of complete seat and back with new moulded foam cushioned 40mm density as shape and size, covered with tapestry cloth as approved along with PVC liping all round, complete all as specified 242 Rubber stopper at the bottom of leg. 243 Chair Verandah MAP(FD/MAP-II/06) 244 Taking out old U/S PVC seat and back and rubber shoes from chair verandah, removing of foreign materials from the iron frame by rubbing with sand paper, painting two coats with white synthetic enamel paintand replace PVC seat and back with 4 mm thick of weight not less that 1.85 Kgs and PVC ribs on seat and back of superior quality as directed by Engineer-in-Charge 245 PVC/Rubber shoes as per sample approved 246 CHAIR REVOLVING LONG/LOW BACK 247 Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size covered with letherate as approved along with PVC liping all round, complete all as specified 248 All as per item No 31.01 here-in-before but for back frame 249 Replacement of Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified 250 replacement of Pedestal assembly complete with hyradlic shocker as directed by Engr-in-charge 251 Replacement of Twin wheel coasters press fitted at the bottom of leg. 252 ALMIRAH LARGE STEEL WITH SHELVES (FD-351/1031) /Almirah Small/ Medium steel (FD-350 /1032/243)/ Locker Bedside Steel (FD-257/1029) :- 253 Shutter (Single Leaf) for Almirah Large Steel made of 1.6 mm thick MS sheet and shall be applied a coat of red oxide primer on both sideafter preparation surfaces 254 All as per Item 32.01 here-in-before but for Almirah Small/medium steel 255 All as per Item 32.01 here-in-before but for Locker Bedside Steel 256 Shelves made of 1.25 mm thick MS sheet and shall be applied a coat of red oxide primer on both sideafter preparation surfaces for almirah Large steel 257 All as per Item 32.04 here-in-before but for Almirah Small/medium steel 258 All as per Item 32.04 here-in-before but for Locker Bedside Steel 259 Six Levers brass lock for Almirah Large Steel/Almirah small/Med Steel Make : Godrej/Harrison/Link with duplicate keys 260 Three way Locking Device forAlmirah Large Steel of 10 mm dia MS rod as per trade pattern incl a coat of red oxide primer 261 All as per Item 32.05 here-in-before but for Almirah Small/medium steel 262 Chromium plated Steel Handle 125mm for Almirah Large Steel/Almirah small/Med 263 Chromium plated MS Key plate fixed with screw and nuts for Almirah Large Steel/Almirah small/Med 264 Chromium plated 100mm Steel Handle D type for Locker Bedside steel 265 Leg for Almirah Large Steel/Almirah small/Med Steel made of 1.6 mm thick MS sheet with Gas welding incl a coat of red oxide primer 266 All as per Item32.08 here-in-before but 1.0 mm thick MS sheet for Locker Bedside Steel 267 75mm Chromium plated haps & stapple fixed with rivets of locker steel 268 Hanging Rod for Locker bed side steeel of 1.6mm thick chromium plated MS Rod 269 CHAIR CB STEEL WITH ARMS/WITHOUT ARMS ( FD-75(M) 270 Seat frame of Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish incl weaving with 2 mm wide half round plastic cane with Godrej pattern & border with 3 mm wide plastic cane superior quality fixed as shown in drawing 271 All as per item No (33.01) here-in-before but back frame 272 All as per item No(33.01) here-in-before but Seat frame for Chair CB Steel without Arms 273 All as per item No (B305.01) here-in-before but back frame 274 Arms rest for Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish 275 PVC cap at top of the frame of the chair (02 Nos to each chair) 276 PVC Shoe at bottom of the frame of the Chairs (04 Nos to each chair) 277 TABLE OFFICE CLERK/TYPIST STEEL(FD-84(M)/1004/FD-1006) 278 Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge.Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed. 279 Drawer made of 22 gauge MS sheet with a coat of red oxide primer 280 Six levers Lock of Godrej/Harrison with duplicate keys. 281 Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece not less than 250mm duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface.Upto 300mm long andpiece will be counted as one. 282 PVC Shoe at bottom of the leg of the Table 283 TABLE OFFICE OFFICER STEEL (FD-84(M)/1003) 284 Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge.Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed. 285 Drawer made of 22 gauge MS sheet with a coat of red oxide primer 286 Six levers Lock of Godrej/Harrison with duplicate keys. 287 Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece not less than 250mm duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface.Upto 300mm long andpiece will be counted as one. 288 PVC Shoe at bottom of the leg of the Table 289 CHAIR executive long back lethaerate (TP) 290 Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size covered with letherate as approved along with PVC liping all round, complete all as specified 291 All as per item No (36.01.01) here-in-before but for back frame 292 Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified 293 Pedestal assembly complete with hyradlic shocker as directed by Engr-in-charge 294 Twin wheel coasters press fitted at the bottom of leg. 295 Briefing chair with writing pad complete Godrej PCH-1712 296 Re-canning of Chair Writing as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane.Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge. 297 Replacement of writing pad with new MDF board writing board and directed by Engr-in-charge. 298 Writng Pad fix with sutable screws 299 Rubber stopper at the bottom of leg. 300 Charpoy IP Hardtop (FD/MAP-II/01) 301 Replacement of old/Unsv plywood with 12mm thick commercial plywood with proper nut and bolt of size as per drawing 302 PVC hard rubber shoes 303 Chair School with Hand Board (FD/E-6/MAP/05) 304 Replacement of old/Unsv one piece PVC seat and back of size as per drawing 305 Replacement of old/Unsv hand board with 18mm thick prelaminated particle with PVC edging (hinged on right hand side screwed to 25mm hollow steel pipe inserted in 20mm MS rod welded to fame) of size as per drawing. 306 PVC rubber shoes 307 Chair Verandah (FD-256, 259, 359) 308 Taking out old U/S cane/newar and rubber shoes from chair verandah, removing of foreign materials from the iron frame by rubbing with sand paper, and welding UNSV frame, painting two coats with white synthetic enamel paintand recanning seat and back with 4 mm wide half round white plastic cane of superior quality as directed by Engineer-in-Charge 309 PVC/Rubber shoes as per sample approved 310 Table Computer FD/E6/MAP/03 311 Provision and replacement of top 18mm Thick Pre laminated Partical board as per drawings. 312 Provision and replacement of18mm Thick Pre laminated Partical board drawer 75mm deep ontelescopic channel as per drawings. 313 Provision and replacement of18mm Thick Pre laminated Partical board key board tray on telescopic channel as per drawings. 314 Provision and replacement of 25 mm thick sqare pipe side support of Table computer as per drawings. 315 Provision and replacement of legs with nylon buffer of Table computer as per drawings. 316 Painting of Steel Furniture Item : All steel surfaces of the following furniture itemswheather exposed to view or not when placed in position shall be painted with high glossy paintto be finished as directed by Engineer-in-Charge duly preparation of surface with emery paper and applying putty as and where required:- 317 BED HARD STEEL (FD/E6/MAP/08(R) 318 CHAIR WRITING MAP (FD/E6/MAP/12) 319 Chair Verandah MAP(FD/MAP-II/06) 320 ALMIRAH LARGE STEEL WITH SHELVES 321 Locker Bed Side steel 322 Almirah small/medium steel 323 CHAIR CB STEEL WITH ARMS/WITHOUT ARMS ( FD-75(M) 324 TABLE OFFICE CLERK/TYPIST STEEL(FD-84(M)/1004/FD-1006) 325 TABLE OFFICE OFFICER STEEL (FD-84(M)/1003) 326 Briefing chair with writing pad complete Godrej PCH-1712 327 Charpoy IP Hardtop (FD/MAP-II/01) 328 Chair School with Hand Board (FD/E-6/MAP/05) 329 Chair Verandah (FD-256, 259, 359) 330 Table Computer FD/E6/MAP/03 331 SCHEDULE A PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch A Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder.
