Tender For Fault Rectification Work (With Accessories) Under Lighting System In Headquarters Building, Annual Rate Contract Year- 2025-26.; 2 PVC Insulation Electric Tape roll 3 P&F of Extension Board having 4 Socket of 6 Amp and 1.5 Mtr. Heavy duty wire. Made on wooden box 4 (60.2) Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Unarmoured/ Armoured aluminium cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume /Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc.including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-(a) Material :- H4- Grade aluminium conductor of purity >99.6 % &as per IS:1554 P-I / IS :7098 P – I (b) conductor shall have electrolytic aluminium confirming to IS8130, IS 3975-1999 for mouring of cables in armoured cableitems , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures. (c) OEM Must have ISO 9001 & 14001 certifications for qualityassuarance & its own in house NABL lab setup for all testing facilities for cables . Appropriate type test certificate / OEM testreport shall be submitted . All above as per pre approved byEngineer in charge. For additional technical parameters of products/work , refer Annexure A attached with this BSR. 5 () Armoured Cable 6 (60.2.3.1) 10 Sq.mm X 2 core 7 (60.2.4.3) 16.0 Sq.mm X 4 core 8 (55.1) Providing & Fixing of 240/415 V AC MCB with positive isolation ofbreaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstandvoltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC, minimum phase termination capacity of35sq.mm. , conductorline load reversibility, label holding facility , IP20 contact protection and fitted with xisting distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000upto 63 A, 5000 for 80 A rating including making onnections,testing etc. as required. . OEM shall have submit NABL / CPRI /ERDA accrediated lab test reports before execution & All as perpre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached withthis BSR . 9 (55.1.1) Single Pole MCB (With B/C curve tripping Characristics) 10 (55.1.1.2) 6 A to 32 A rating 11 (55.1.2) Double Pole MCB (With B/C curve tripping Characristics) 12 (55.1.1.4) 50-63 A rating 13 (50.4) S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III )vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as required in recessincluding cutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports byany NABL accredited lab for the conduit shall be submitted beforeexecution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer AnnexureA attached with this BSR . 14 (50.4.2) 25 mm 15 (53.1) Supplying and drawing FR PVC insulated & unsheathed flexiblecopper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wireshould be made from 99.99% purity copper, class 5 stranding inacc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) forless chances of oxidization and higher silver content for gives betterconductivity , insulation PVC type A or C ,flame retardant as per IS10810-53, better amperage rating as per VDE 0298 part 4, , inexisting surface or recessed PVC/ MS conduit/casing cappingincluding all as per pre approved by Engineer in onnections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additionaltechnical parameters of products/ work , refer Annexure Aattached with this BSR 16 (53.1.7) 2 x 2.5 sq.mm+ 1x1.5sqmm 17 (53.1.14) 2 x 4.0 sq.mm 1 x 2.5 sq. mm. 18 (53.1.19) 2 x 6.0 sq.mm 1 x 2.5 sq. mm. 19 (58.3) SITC of IP 40 3 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings as per PWD specification for electrical Works, conforming to IS/IEC 60947 P -2 :2003 with front face and ntralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 800 V, provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making onnections with lugs & spreaders, etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 20 (58.3.3.3) up to 125 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu 21 (58.3.3.5) 200 Amp , 35 kA, adjustable O/L & fixed S/C setting, Ics = 100 % 200 Amp , 35 kA, adjustable O/L & fixed S/C setting, Ics = 100 % 200 Amp , 35 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu 22 (56.1) P & F ISI marked (IS:3854) 6 amp. flush type non modular switch with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 23 (56.2) P & F ISI marked (IS :3854) 16 amp. flush type non modular switch CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 24 (56.3) Providing & Fixing of 6 amp. Combined flush type non modular socket and switch set as per PWD specification for electrical Works,made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 25 (56.4) Providing & Fixing of 16 amp. Combined flush type non modular socket and switch set with indicator and fuse set as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 26 (56.27) Providing & Fixing of modular type switch/ bell push duly ISI marked (IS :3854) with CM/L no. printed and made out of unbreakable and fire retardant vergin UV Stabilized Polycarbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating ,minimum width of switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in-charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure A attached with this BSR 27 (56.27.1) 10 A one way switch 28 (56.27.4) 16 A one way switch With Led Indicator 29 (56.28) Providing & Fixing of modular type lockable feature socket duly made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in-charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure A attached with this BSR 30 (56.28.1) 6 A 3/5 pin shuttered socket 31 (56.28.2) 6/16 A shuttered socket 32 (56.33) Providing & Fixing of Wiring Accessories OEM fabricated following size virgin material UPVC modular boxes on surface suitable for modular accessories as required.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 33 (56.33.1) 1-2-3 Module 34 (56.33.2) 4-5 Module 35 (56.33.3) 6-8 Module 36 (56.33.4) 10-12 Module 37 (56.3) Providing & Fixing of following modular accessories as per PWD specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in-charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure A attached with this BSR 38 (56.30.6) Blanking plate 39 (56.30.10) Modular MCB 6 A to 32 A SP 40 (56.29) Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in-charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure A attached with this BSR 41 (56.29.1) 5 step fan regulator 2 Module 360 dgree rotating 42 (66.1) Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 43 (66.1.1) 1170mm(+/-10%) LED batten with min. lumen output 2200 lm 44 (66.1.2) 570mm (+/-10%) batten with min. lumen output 1000 lm 45 (66.3) Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / Sqaure SMD Mid Power LED Downlight with power coated die-cast aluminum housing with UV Stabilized non yellowish Diffuser with BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% . System Lumen efficacy of ≥ 110 lm / watt, THD < 10 % , Pf.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 46 () Recessed Mounting 47 (66.3.1.1) Minimum lumen output 330 lm 48 (66.3.1.2) Minimum lumen output 650 lm 49 (66.3.1.3) Minimum lumen output 1300 lm 50 (66.3.1.4) Minimum lumen output 1600 lm 51 (66.3.1.5) Minimum lumen output 1950 lm 52 (66.3.1.6) Minimum lumen output 2400 lm 53 (66.4) P&F of IP20, 2x2 LED Surface/ Recessed mounting Mid power SMD type LED Light fixture not less than 50mm housing depth made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 4 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in- charge. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 54 () Recessed Mounting 55 (66.4.1.3) Minimum lumen output 4200 lm 56 () Surface Mounting 57 (66.4.2.3) Minimum lumen output 4200 lm Please Enable Macros to View BoQ information
