Tender For Work Of Purchasing/Installing Cable/Wire, Mcb, Isolator, Timer And Contactor For Repair Of All Street Lights And Ccms Panels Installed In The Municipal Council Area.; 1 based on Ruidp 2023 2 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. 3 Single pole MCB (With B/C curve tripping Characteristics 4 6 A to 32 A rating 5 50/63 A rating 6 Four pole MCB (With B/C curve tripping Characteristics) 7 50/63 A rating 8 Providing & Fixing of AC operated heavy duty 230 /440 Volt power contactor as per PWD specification for electrical Works, ISI marked IS/IEC 60947-4-1 : 2000 having provision of mechanical interlocking, auxilary contacts, Din rail mounting type including making connections, testing etc. as required. All as per pre approved by Engineer in-charge. For 9 4 pole Power contactors with following AC 1 Rating 10 63 Amp 11 100 Amp 12 Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering overall poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. 13 Four pole Isolator 63 A rating 14 80 A/ 100 A rating 15 Providing & Fixing of mechanical / digital time switch having following day / week programme and minimum 100 hours reserve and AC1 rating of 16-20 amperes including making connection, programming conforming to IEC 60730-1 and 60730-2-7 etc. as required. All as per pre approved by Engineer in-charge. For 16 One day reserve (Analog type ) 17 One day & week reserve (Analog type ) 18 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810. For additional technical parameters of product / work refer Annexure A attached with this BSR 19 4.0 Sq. mm 20 2 core 21 6.0 Sq. mm 22 2 core 23 10.0 Sq. mm 24 2 core 25 16.0 Sq. mm 26 2 core 27 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR 28 2 x 6.0 sq.mm 29 2 x 10.0 sq.mm 30 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured Copper cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810 For additional technical parameters of product / work refer Annexure A attached with this BSR 31 2.5 Sq. mm,6 core 32 Supplying and drawing of XLPE insulated LT Aerial bunched Aluminium conductor cable confirming to IS 14255/1995 and IS 398 (Pt-4)/ 1994 and as per Discom Specs. on existing cross arms through I hook with all necessary T&P required including binding and twisting etc. complete in all respect as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 33 1 X 25 sq. mm. + 1X25 sq. mm. (insulated) 34 Supply and fixing of following LT Supporting accessories with nutbolt & Clamps made out as per standard Discoms specificationswith two coats of Red oxide and two coats of Aluminium paint etc.asrequired. All as per pre approved by Engineer in-charge.Foradditional technical parameters of product / work refer Annexure Aattached with this BSR 35 Suspension clamp with eye hook & Pole clamp 36 Supply and fixing of LT porcelain pin insulator as per IS 1445-1997and as per Discoms standard specifications,suitable for workingvoltage 1100 volts including all accessories like MS Forged GI LTPin confirming to IS:7935/1975 (latest amended) Nut, Bolt etc. as RUIDP 547 ISOR 2023 Code No Description Unit Rate Rs. required. All as per pre approved by Engineer in-charge.For additional technical parameters of product / work refer Annexure Aattached with this BSR 37 100 mm x 70 mm 38 Providing & Fixing of ISO certified company made TP&N 415 V side handle operated double break fuse switch unit in sheet steel enclosure as per PWD specification for electrical Works conforming to IS/lEC 60947-3 : 1999 (W/O HBC fuses) including making connections with suitable lugs, testing etc. as required. Appropriate type test certificate / OEM test report shall be submitted . All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 39 100 A rating 40 200 A rating 41 P & F of IP 55 protected light controlled switch based on infrared sensing and daylight with built in over load protection, timer to switch OFF at preselected time. Switch shall have 7 day power backup without hampering of preset time and over ride facility formaintenance purpose (RUIDP SOR 2017) 42 Suitable for 3 kw load direct lighting load (single phase) 43 Suitable for 15 kw load (three phase) includingcontactor, MCB, cable glands, terminal block and locking arrangement Please Enable Macros to View BoQ information
