Tender For Special Repair Work Of Barkhera Piprakhas Road - Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5m and lead upto 50m as per technical specitication clause 302.3 2 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 P.C.C. Grade M 10 3 Brick Masonry Work in Cement Mortar 1:3 in Foundation complete excluding Pointing and Plastering, as per Drawing and Technical Specifications Clause no.600,1200&1203 4 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 P.C.C. Grade M 20 5 12 mm thick plaster with Cement mortar over brick work minimum thickness not to be less than 3/8 (10 mm) thick including supply of all materials, labour and T&P etc. required for proper completion of the work with cement and coarce sand of 1.25 F.M. mort 6 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 4.7-405(3) of MoRD 7 Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing bymix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specificatin Clause 401 8 Providing and laying factory made 80 mm thick interlocking cementtiles(30mpa)including 25 mm thick compacted bed of fine sand complete 9 Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 carted up to 1 km. 10 Providing concrete for reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802,803, 1202 & 1203 RCC grade M 25 11 Supplying, fitting and placingTMT bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202 12 Construction of unreinforced, plain cement concrete pavement thickness as design, over a prepare subbase, 43 grade cement for any other type as per clause 1501.2.2 M30 (grade), coarse and fine aggregates confirming to IS383, maximum size of coarse aggregate not exceeding 25mm, mixed in a concrete mixer of not less then 0.2cum capacity and appropriate weight batcher using approved mix desing, laid in approved fixed side from work (steel channel, laying and fixing of 125micron thick polythene film, wedges, steel plates including levelling the form work as per drawing), spreading the concrete with shovels rakes, compacted using needle and plate vibrator and finished in continous opreation including provision of contraction and expansion, construction joint approved curing of concrete slabs for 14 days with water finishing to line and grade as per drawing and techenical specification clause 1501 of MoRD 13 Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2as per Technical Specification Clause 303.1. 14 Providing and applying tack coat with Bitumen (VG-10) using emulsion distributor at the rate of 0.30kg per sqm on the prepared bituminous surface as per Technical Specification Clause 5.2-503(iii) of MoRD 15 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or bitumen VG-10 or emulsion to required line, grade and level to serve as wearing course on a previously repared base,including mixing in a mixall, aying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type C as per Technical Specification Clause 508. of MoRD 16 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Technical Specification Clause 5.12-510 of MoRD
