Tender For Special Repair To Bldg No. M-04 And Ow-13 At Palampur Mil Station; 1 Demolition of cement concrete (unreinforced) in ground floor and pavingn.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed. 2 Demolition of brick workor stonework built in cement mortar including allquoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed. 3 Taking down cement plaster including backing etc from brick/stone walls / concrete surfaces including raking out joints,hacking for key , scrubbing down with water etc complete all as specified and directed 4 Taking downand removing chowkats with shutters (withouttaking off shutters from chowkat)not exceeding 1.50 Sqmeach complete all as specified and directed. 5 Taking down and removing chowkats with shutters (withouttaking off shutters from chowkat)exc 1.50 Sqmbut not exc 4.00 Sqm each complete all as specified and directed. . 6 Dismantling plain or corrugatedsteel sheetsany gaugethickness including Nanital or similar pattern roof covering including ridges complete all as specified and directed. 7 Dismantlingtimber in scantling 40 sqcm and over in section un-framed work complete all as specified and directed. 8 Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. 9 Dismantling framed trusses , span not exc 10mtrusses, include unbolting, dismantling framed work into two or more portable parts and marking members for re-erection, complete all as specified. 10 Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed. 11 Dismantling boarding, any description, fixed in any position with screws, complete all as specified. 12 Dismantling posts or struts (wood, steel or R.C.C.) any section, embedded in concrete, brick or masonary work including taking out embedded portion and making good disturbed ground as specified allas directed by Engineer-In Charge. 13 Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in any type ofsoil, complete all as specified and directed. 14 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and directed. 15 Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed. 16 PCC 1:4:8 (nominal mix) type D-2(using 40mm graded crushed stone aggregates) as in foundation filling and mass concretecomplete all as specified and directed. 17 Plain cement concrete 1:3:6 ( nominal mix )type C-2(using 40 mm graded crushed stone aggregate) as insurface channel drains all as specified and as directed. 18 Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc., complete all as specified and as directed. 19 PCC 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified. 20 Precast rein-forced cement concrete as in landing, cover slabs (for manhole etc) and similar articles withprecast cement concrete Type B-1, 1:2:4 (20mm graded crushed stone aggregate) and setting in cement mortar 1:4 complete all as directed. 21 Reinforced cement concrete , 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified. 22 Reinforced cement concrete Foundations, including rafts, 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in chajjas, complete all as specified. 23 Brick work with old size fly ash bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:6 all as specified & directed. 24 Use & waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or tobatter for rough finished surfaces of concrete, complete all as specified & directed. 25 Use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beams for rough finished surfaces of concrete, complete all as specified & directed. 26 Use & waste of form work to chullah hoods, chajjas, troughs and similar items includingedges for fair finished surfaces of concrete, complete all as specified & directed. 27 Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 all as specified & directed. 28 Walling of random rubble stone masonry,uncoarsed, well bonded, bedded and soilidly hearted,built in CM 1:6, complete all as specified and directed. 29 All as per item 28 above but except stone 30 Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 125 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkatscomplete all as specified. 31 Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing of glass, particle board,aluminium frame etc complete all as specified and directed. 32 35mm thick2nd class hardwood Plain framed, panelledshutter (Factory Made) (two panel) with lock rail and panel of 9 mm B.W.P. commercial plywood . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated and fitted to chowkats complete all as specified and directed. 33 35 mm thick 2nd class hardwood glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members ofdoor shutters as specified in SSR- 2009Part-I Section 8.24(a) complete all as specified and directed. 34 Factory Made Solid PVC Moulded Door Shutter, with particleboard core,28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawinge,as shown on page No176 to 183 of MES SSR 2020 Part-II compete all as specified and directed. 35 Powder coated (minimum thickness of powder coating 50 micron),Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. 36 Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware.EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories and 5mm thick glass of selected quality . ,complete all as specified. 37 Extruded aluminium alloy handles, fabricated type, anodised of size 125 mm complete all as specified and directed. 38 Aluminium anodizedbarrel tower bolt of extruded section of size 150 mm and fixed complete all as specified and directed. 39 Mild steel butt hinges of size 100mm medium weight cold rolledcomplete all as specified and directed. 40 300mm longBrass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixedcomplete all as specified and directed. 41 Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete, overall length of cover plate 140mm, complete all as specified and directed. 42 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified. 43 Galvanished mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanished wire staples complete all as specified and directed. 44 Sheet glass, 4.8 mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed. 45 Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all asspecified. 46 Aluminium (extruded section) body ,door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg ,complete all as specified and directed. 47 Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. 48 Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers bent to shape required, including cranking, bending spirally for hooping for columns, hooking endsand binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. 49 Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework ofwater tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and as directed. 50 RolledMild Steel Work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410- W(Gde-E-250) quality- A, complete all as specified and as directed. , complete all as specified and as directed. 51 RolledMild Steel Work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. conforming to Fe-410- W(Gde-E-250) quality- A, complete all as specified and as directed. , complete all as specified and as directed. 52 Rolled mild steel work as in Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed. 53 Rolled mild steel work as in Plates (plain or chequered) channels, square cut or notched(ordinary and counter sunk) forming holes, without any attachment conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed. 54 Mild steel bolts. purpose made. square head one end and screwed the other, or screwed both ends; each screwed end to be fitt ed with washers and one hexagonal or square nut. Exc 30cm long, diameter of neck not exc 12mm, complete all as specified. 55 Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, all as specified and directed. 56 Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. 57 Providing and fixing tiled false ceiling of size 595x595mm in true horizontal level suspended on interlocking gypric metal grid of hot dipped galvanized steel section (galvanized @ 120 gms/sqm, both side inclusive) consisting of 3600mm long main T runner size 24x38mm and 0.30mm thick, 1200mm long cross T of size 24x25mm and 0.30mm thick, 600mm secondary cross T of size 24x25mm and 0.30mm thick and PPGI wall angle of size 24x24mm and 0.4mm thick, bottom exposed capping of width 24mm of all T-sections shall be of 0.25mm thick PPGI, wall angle is fixed along the perimeters of the ceiling to walls, partitions or columns etc with rawl plugs and wooden screws at 300mm centers MainT runners are then suspended from ceiling using GI slotted cleats of size 27x37x25x1.6m fixed to ceiling with 8mm dia and 45mm long dashfasterners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8mm spaced at max 1200mm center to center along main T and not more than 150mm from spliced joints. The last hanger at the end of each main runner should not be greater than 600mm from the adjacent = wall, then 1200mm long cross T is interlocked between the main T at 600mm center to center to form a grid of 1200x600mm and then secondary cross T of length 600mm is then interlocked at middle of the 1200x600mm grid to form grids of 600x600mm. Cross tees at the ends having length more than 600mm are to be supported independently. Finally providing whitecoloured Gyproc 8mm thick Dew Drop/Granular tiles of size 595x595 having foil on back side & PVC paper on front side wrapped around edges to be placed in grid complete all as specified and directed. 58 Clip-in false ceiling system with plain steel beveled edged tile (600mmx600mm) manufactured out of 0.70 mm aluminium sheet having power coatingwith 60 microns polyester paint on front side. Two sides of each tile shall be rised and piped and stopped to ensure positive engagement into the spring clip-in profile allowing for demounting of indivual tiles. The rigid suspension system consists of rows of galvanized steel 0.50 mm thick clip-in profile of size 38mm x 20 mm and installed at 600 mm c/c spacing to support the tiles clip-in profiles shall be suspended and jointed from galvanized steel ‘C’ channels of size 10mm x 38mm x 10mm with hold on clamps at spacing as specified by manufacture. Suspension angles shall be suspended from the roof structure by GI ceiling brackets as per manufacture instructions and jointed to the ‘C’ channels. The tiles shall be held in place by pressure clips ‘C’ at spacing as per manufactures instructions. GI wall angle shall be used on wall angle shall be used on wall of size 20mm x 30mm x 20mm and 0.5mm thick with matching the color with tiles all as per manufacture specifications/ instructions and includingnecessary scaffolding all as specified and directed by Engr-in-Charge 59 25mm thick, lnsulated PVC Wall Lining consisting of PVC Insulated Panels having expanded polystyrene (EPS) stuck to 2mm thick single side prelamPVC sheet duly fitted into the wall as perspecifications and drawing, complete all as specified. 60 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, complete all as specified 61 75mm thick PCC 1:2:4 type B-2 (using 40 mm graded crushed stone aggregates) as in sub base complete all as specified and directed. . 62 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in sub base complete all as specified and directed. . 63 Plain cement concrete 1:3:6, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75mmthick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved). 64 Vitrified ceramic tiles (light shade) 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm as directed by EIC as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete , including dismantling old tiles and rubbish off permises, all as specified and directed. Note:Size/Shade/Colour of tile shall be approved by the GE. 65 Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match including dismantling old tiles and rubbish off permises, all as specified and directed. Note:Size/Shade/Colour of tile shall be approved by the GE. 66 Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match including dismantling old tiles and rubbish off permises, all as specified and directed. Note:Size/Shade/Colour of tile shall be approved by the GE. 67 20mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. complete all as specified and directed. 68 Glazed ceramic colouredtilesof size350x 250x 7 mm/ 450X 350X 7mmthick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 including dismantling old tiles and rubbish off permises, all as specified and directed. Note:Size/Shade/Colour of tile shall be approved by the GE. 69 Chequered cement concrete colouredtiles, homogenious texture glossy finished, chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 20 mm thick cement screed in cement mortar 1:4 complete all as specified and directed. 70 Rendering cement plaster 10mm thick in cement mortar 1:6 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified. 71 Rendering cement plaster 15mm thick in cement mortar 1:6 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified. 72 Rendering cement plaster 15 mm thick in cement mortar 1:4 (1 cement : 4coarse sand), on other than fair faces of brick wall or on stone masonry surfaces, trowelled to even and smooth finish without using extra cement complete all as specified. 73 Rendering cement plaster 15mm thick in cement mortar 1:4 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified. 74 Raised pointing to random or polygonal rubble, uncoursed or brought upto coursesmasonary 1n CM 1:4, complete all as specified. 75 Preparation of new wooden surfaces of any description, not otherwise described, over 10cm in width or girthand applying two coats of synthetic enamel paintover a coat of pinkprimer complete all as specified and directed. 76 Preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise describedand applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and directed. 77 Preparation ofnewplastered surfaces or un plastered, previously undecorated wall surfaces and applyingtwo coats of oil bound distemper , complete all as specified and directed. 78 Preparation ofnewplastered surfaces or un plastered, previously undecorated wall surfaces and applyingtwo coats of cement base paint , complete all as specified and directed. 79 Preparation ofnewplastered surfaces or un plastered, previously undecorated wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm, complete all as specified and directed. 80 Preparation ofoldplastered surfaces or un plastered, previously undecorated wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm, complete all as specified and directed. 81 Preparation ofnewplastered surfaces or un plastered, previously undecorated wall surfaces and Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification. Two or more coats on new work, over 2mm thick wall care putty complete all as specified and directed. 82 Preparation ofoldplastered surfaces or un plastered, previously undecorated wall surfaces and Distempering with 1st qality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification.,Two or more coats on oldwork, over 2mm thick wall care putty complete all as specified and directed. 83 Stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup(concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore iron pipe or for unionsfixed in repair complete all as specified. 84 Angle Valve (externally threaded) , cast copper alloy, chromium plated , fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore iron pipe or for unionsfixed in repair complete all as specified. 85 Bib tap, long body, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repair, complete all as specified and directed. 86 Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed 15 mm bore,suitable for bath/WHB fixed in repair, complete all as specified and directed. 87 Brass chromium plated shower rose 125mm sizewith or without swivel joints, including fixing to steel pipe or union.fixed in repair complete all as specified. 88 Sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. 89 Brass chromium plated , tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified. 90 Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position completein all respect , fixed in reapir as specifiedall as specified. 91 Chromium plated jet spray,for 15mm bore ofpipe, 1 to 15 metre acrylic tube, fixed in repair , complete all as specified. 92 1200x600 mm bevelled edge mirror of slected quality 4.5mmthick polished glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers, complete all as specified. 93 Soap dish, SS, approximate size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws, fixed in repair complete all as specified. 94 S&F in repairs, Chromium plated Toilet Paper Holder with Flap Recessed Type, fixed to walls with chromium plated brass screws, completeall as specified. 95 PVC connections 15 mm size with PTMT nutsof length 450mm ,complete all as specified and directed. 96 Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, complete all as specified 97 Vitreous China wash down water closet (pedestal pattern), white including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC white seat cover andchromium plated jet including PVC connection, fixedcomplete including demolition of old unservicable WC and provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, fixed in repairs all as specified. Make: Cat Part No. 2008 for EWC, 2308 for seat cover, 2201/B for internal fittings ofCera or equivalent makes mentioned in PS. 98 Wash basins, Vitreous China , oval shaped , counter,size 560mmx470mmx190mm, colouredincluding cutting of top, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot or ‘Cold with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, completeall as specified. Make: Cat Part No. S2030104of Cera or equivalent in makes mentioned in Appx C 99 Vitreous china urinal, half stall type,white, including fixing bolts, flush pipe, PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 7.0 litre, PVC waste pipeincluding providing and fixing plugs,including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe, complete all as specified and as directed. 100 G I tubingmedium gradeof 15 mm borewith all fittings and fixtures fixed to wall and ceiling or laid infloor/trenches, including taking down old GI tubing, ccomplete all as specified and directed. 101 G I tubingmedium gradeof 20 mm borewith all fittings and fixtures fixed to wall and ceiling or laid infloor/trenches, including taking down old GI tubing, ccomplete all as specified and directed. 102 Gun metal globe orgate valve with iron wheel head, screwed both ends for iron pipe and fixedbore dia of pipe 25mm complete all as specified and directed. 103 110mm dia PVC(SWR)pipe single socketed with rubber ringjoints, laid in trenches or in floor , fixed in repair, complete all as specified and directed. 104 75mm dia PVC(SWR)pipe single socketed with rubber ringjoints, laid in trenches or in floor , fixed in repair, complete all as specified and directed. 105 75 mm dia PVC(SWR) bend, any radius complete all as specified and directed. 106 75mm dia PVC (SWR) junction single, (single T) equal or unequal provided with oval access door complete all as specified and directed. 107 110 mm dia PVC(SWR) bend, any radius complete all as specified and directed. 108 110mm dia PVC (SWR) junction double, (double T) equal or unequal provided with oval access door complete all as specified and directed. 109 Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and directed. 110 75mm dia PVC (SWR) multi floor trap with grating including jointing with solventcement, complete all as specified and directed. 111 110 mm dia PVC(SWR) vent cowl complete all as specified and directed. 112 Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supplyline including dismantling old tank complete all as specified. 113 Stainless steel curtain rod, 20mm dia including brackets with cut hole suitable for 20mm dia rod fixed with screws and gutties in wall, including end caps with wall ornament and fixed to curtain rod with screws of design/ shape , fixed in repair, complete all as specified and directed. 114 Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing fan regulator any type (Where required) and electric meters are to be refixed and connected properly where required. 115 Taking down main switches, distribution board, steel enclosure with MCBs any way and rating including wooden board or from steel board and making good distubed surfaces complete all as specified and directed. 116 Taking down the sub main wiring of any size from the wall/roof/ceiling and removing from the site and making good disturbed surface complete all as specified and directed. 117 M&L for point wiring for one light/fan/call bell point controlled by one 5/6 Amp switch with 1.5 Sqmm two single core multistranded copper conductor FRLSH, PVC insulated (unsheathed) heavy duty cable 1100 volts including continuous earth wire of size 1.5 Sqmm copper conductor multistrand FRLSH, PVC insulated (unsheathed) drawn into concealed rigid non-metallic PVC conduit Medium Grade ISI marked not less than 20mm wide of 1.8mm wall thickness ISI marked including modular GI sunken flush box (Pressed steel powder coated Modular GI sunken flush boxese of any way i.e. 1 to 12 way as per site requirement suitable for modular switch/socket) for mounting switches, and including modular white cover plate with frame 1 to 12 way as per site requirement , way sockets, fan regulators etc & making good to disturbed surfaces as well as matching with existing whitewash colour/surface complete all as specified and as directed for the following:- (a)Wiring shall be done by using proper colour coding(b)Earth wire shall be of green colour(c)On RCC roof/ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed. 118 All as per serial item No 117 above, but for one 3 pin 5 Ampssocket outlet, on same board all as specified and directed. 119 All as per serial item No 117 above, but for one 3 pin 5 Ampssocket outlet, independent all as specified and directed. 120 All as per serial item No. 117 above but for 3 pin 15 Amps socket out letindependentwith 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified. 121 Modular bell push 1 way 6A, 1 module complete all as specified and directed. 122 Modular switch 1 way 6A, 1 module complete all as specified and directed. 123 Modular socket, 6A-2/3 pin combined 2 module complete all as specified and directed. 124 Modular socket, 6A and 16A, 2/3 pin combined 2 module complete all as specified and directed. 125 Modular switch 1 way 16A, 1 module complete all as specified and directed. 126 Modular White cover plate with frame, 8 module, complete all as specified. 127 Modular White cover plate with frame, 6 module, complete all as specified. 128 Modular White cover plate with frame, 3 module, complete all as specified. 129 Modular White cover plate with frame, 1 module, complete all as specified. 130 Modular Fan step regulator, 120W - 2 module, complete all as specified. 131 S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20 Amp & making good to disturbed surfaces as well as matching with existing whitewash colour/surface complete all as specified and directed. 132 Bell, AC, 230 volts, single pole all as specified. 133 Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified. 134 Lamp holder, PVC/Polycarbonate type with back plate suitable for angular/ batten fittingscomplete all as specified & directed. 135 Sub main wiring with two single core PVC insulated cable1100 volts grade with copper strandedRLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire ofsize 6 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly , complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor andone RM of earth wire of 6 Sqmm,shall be measured as one RM). 136 MCB SPN 32-40 Amp, 240 Volts, 10 KA, C Curve all as specified. 137 MCB SPN 63 Amp, 240 Volts, 10 KA, C Curve all as specified. 138 MCB SP 6 to 32 Amp, 240 Volts, 10 KA , C Curve all as specified. 139 Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 8 way, double door, 240 volts with 200 Amp rated bus bar completed all as specified. 140 Sheet metal enclousers, TPN Distribution board 4 way 415 V, double door with 100A MCB TPN as incomer complete with copper bus bar and neutral link earthing fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.Note:- Distribution board and MCBs should be same make. 141 Factory made CRCA steel powder coated double door frame, board of 2mm thick sheet of size 50cmx50cmx15cm , wall mounted type partially mounted in wall with locking arrangement handle and making good disturbed surface to match existing specifications ( white/ colour wash)and fixing only existing 02 Nos old energt meters with seperate compartmentincluding connection , complete all as specified. 142 LED type tube light, 1x20 watt 230 volts wall mounted Inverter LED batten with square profile and polycarbonate channel. Lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours,internely pre wired and including connecting up with three core twisted flexible copper conductor cable of suitable size. Make: Havells cat part No. LHEXACP7FN1W020 or equivalent in Appx 143 LED Luminaire 600mmx600mm, 36 watt, 6500K, Ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting withArmstrong/Grid ceiling, complete all as specifiedMake: Havells cat part No. LHEBAEP7IW1W036 or equivalent in Appx 144 LED Bulk Head 10W with pressure plastic housing with clear prismatic diffuser, high efficient LEDs IP66 complete all as specified and directed. 145 Fancy Lights with LED bulb holder, plastic housing with clear prismatic diffuser , with IP 42 , as per sample approved by GE, complete all as specified, 146 Disconnecting/ Taking down Exhaust fan/Ceiling fanof any sweep removing and cleaning the dust properly, painting with same colour good quality synthethic enemelled paint after preparing surface for painting with existing color shade oiling and greasing of bearing including refixing and making the conection and testingcomplete all as specified and directed. 147 Supply and installing of electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. including steel braided flxeible connection for pipe of size 15mm dia bore GI hexagonal adopeters./ Nuts on both sides of inlet (Cold water supply) & outlet (hot water supply) and including provision of wall mouting arrangement and mounting on wall with suitable size of anchor bolts with complete connection of water including testing after installation complete all as specified and as dierected by Engr-in-Charge. Note : (i)Rate also includes for taking down old geyser . Old geyser shall be deposited in MES store yard. 148 Disconnecting electronic meters temper proof LCD display and taking in safe custody and refixing the same with caliberation and cleaning and making the conection and testingcomplete all as specified and directed. 149 Sand cushioning to under ground cables provided with a layer of sand 8 cms thick before laying the cable and 15 cms thick after laying the cable complete all as specified and directed. 150 Sub class B bricks for covering to cable laid dry flat, with width equal to length of bricks all as specified and directed. 151 GI pipe light grade of size 40 mm dia laid in trenches/ walls including clamps, screws etc, complete all as specified and directed. 152 XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 25 Sqmm, 4 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed. 153 Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC (1:2:4), type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC (1:2:4), type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixingarrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electricalplate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. 154 Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 31 of tender doucments.
