Tender For Face Upliftment Of Type-Iv Quarters In Rcf Estate At Chembur, Mumbai 400074 Phase Ii; 1 Excavation for foundation, substructures, basements, tanks, sumps, walls, chambers, manholes, trenches, poles, pits & general building works in soft/ disintegrated rock, sand stone, stiff clay, gravel, cobblestone, hard laterite, water bound macadam, wet mix macadam, asphalt mix carpet of any type, pitching, soling, paths and hardcore, lime concrete, plain cement concrete, stone masonry and all types of brick/ block masonry below ground level, rock boulders, etc. for depths/ lifts upto 1.5M measured from the ground level, including dressing/ trimming the sides, leveling of bottoms, manual dewatering, removing rank vegetation, backfilling in layers not more than 200mm thickness, watering, consolidating, compacting to achieve not less then 97% Modified Proctor density conforming to relevant IS, stacking in measurable heaps for future use within owners space or disposing within an initial lead of 150m as directed, loading, unloading, leveling excluding shoring, strutting etc. complete as directed by Engineer-in- Charge.Note:1) The rate includes the handling/supporting the existing utilities such as cables, drains, pipes, water mains etc.2) It also includes the royalty and other taxes if any 2 Filling in plinth, floors, trenches, pits with approved excavated materials, murum / good earth in layers not exceeding 200mm including breaking of clods, watering, consolidating each layer in filled up area by rolling and compacting with roller/ plate compactor as required to achieve not less than 97% modified proctor density conforming to relevant IS etc. complete as directed byEngineerIncharge. Note:1) The rate includes the royalty and other taxes if any. 3 Filling in plinth, floors, trenches, pits with approved contractors murum in layers not exceeding 200mm including breaking of clods, watering, consolidating each layer in filled up area by rolling and compacting with roller/ plate compactor as required to achieve not less than 97% modified proctor density conforming to relevant IS etc. complete as directed by Engineer In charge. The rate includes necessary soil testing charges at laboratory & field as per relevant I.S. codes, royalty, octroi and other taxes if any. (Note: Borrow areas selected by CONTRACTOR shall be got approved from Engineer In Charge, before executing the work)1) The rate includes the royalty and other taxes if any. 4 Providing & Laying dry stone Rubble Soling with average 230 mm size hard stone set in regular lines, handpacked and interstices thoroughly filled with small chips including filling in with good quality murum brought from outside, compacting with iron rammers, watering, sand spreading 12mm thk. layer of grit on top etc complete as directed by Engineer In Charge. (Note: The rate includes the royalty and other taxes if any 5 Providing and laying in position plain cement concrete of specified grade cement with trap/granite/quartzite/gneiss metal mixing in concrete mixer including bailing out water, compacting, finishing surface, curing and including the cost of centering and shuttering at all level :Nominal Mix of 1:2:4 (1 cement OPC: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 6 Providing and laying in position plain cement concrete of specified grade cement with trap/granite/quartzite/gneiss metal mixing in concrete mixer including bailing out water, compacting, finishing surface, curing and including the cost of centering and shuttering at all level :Nominal Mix of 1:4:8 (1 Cement OPC: 4 coarse sand : 8 graded stone aggregate 20 mm nominal size). 7 Brick work with common burnt clay modular bricks of class designation 3.5 and above in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) 8 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 and above in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) 9 Providing and applying 6 mm thick internal sand faced ceiling plaster in cement mortar 1:3 at all heights and locations in single coat for concrete surfaces including scaffolding, hacking of concrete surface, watering, finishing, curing etc. complete. 10 Providing and applying 12 mm thick internal sand faced plaster in cement mortar 1:3 at all heights and locations in one coat for masonry (except stone masonry) and concrete surfaces including racking out joints, hacking of concrete surface, watering, finishing, curing, scaffolding etc.complete. 11 Providing and applying 20 mm thick external sand faced cement plaster upto 10m from ground level and at all locations in cement mortar proportion specified below in two coats for masonry (except stone masonry) and concrete surfaces including providing water proofing compound to the first coat of plaster as per manufacturers specification, racking out joints, hacking of concrete surface, finishing, curing, scaffolding, etc complete as directed By Engineer In charge.In cement mortar 1:4 12 Providing and applying first single coat of approved primer and two coats of acrylic distemper (oil bound distemper) of an approved make and colour as per manufacturers specifications to any surface, at all height and locations as directed including scaffolding, cleaning and preparing surfaces for painting with broom by any approved means, etc. complete as directed by Engineer-in-charge. 13 Providing and applying first single coat of approved primer and two coats of synthetic enamel paint/flat oil paint of an approved make and colour as per manufacturers specifications to surfacesspecifird below, at all height and locations as directed including scaffolding, cleaning and preparing surfaces for painting by any approved means etc.complete as directed by Engineer-in-charge For plastered wall surface 14 Providing and applying first single coat of approved primer and two coats of synthetic enamel paint/flat oil paint of an approved make and colour as per manufacturers specifications to surfacesspecifird below, at all height and locations as directed including scaffolding, cleaning and preparing surfaces for painting by any approved means etc. complete as directed by Engineer-in-cha rgeFor woodwork 15 Providing and applying first single coat of approved primer and two coats of synthetic enamel paint/flat oil paint of an approved make and colour as per manufacturers specifications to surfacesspecifird below, at all height and locations as directed including scaffolding, cleaning and preparing surfaces for painting by any approved means etc.complete as directed by Engineer-in-chargeFor steelwork 16 Providing and applying first single coat of approved primer and two coats of acrylic plastic emulsion paint of an approved make and colour as per manufacturers specifications to any surface, at all height and locations as directed including scaffolding, cleaning and preparing surfaces for painting by any approved means etc. complete as directed by Engineer-in-charge 17 Providing and applying single coat of an approved make primer for waterproof cement paint as per manufacturers specifications to the smooth surface, upto 10m height from ground level and at all locations as directed including preparing surfaces for painting by any approved means, scaffolding, cleaning and curing etc. complete as directed byEngineer-in-charge 18 Providing and applying first single coat of approved primer and two coats of waterproof cement paint of an approved make and colour as per manufacturers specifications to any surface, upto 10m height from ground level and at all locations as directed including preparing surfaces for painting by any approved means, scaffolding, cleaning and curing etc. complete as directed by Engineer-in-charge. 19 Providing and applying first coat of approved waterproof primer, one coat of waterproof acrylic based textured exterior paint of an approved make and colour as per manufacturers specifications to textured sand faced or other surfaces, upto 10m height from ground level and at all locations as directed including preparing surfaces for painting by any approved means, scaffolding, cleaning and curing etc. complete as directed by Engineer-in-charge 20 Providing and applying first single coat of approved primer and two coats of anti-algal, anti-fungal, exterior paint as specified below of an approved make and colour as per manufacturers specifications to any surface, upto 10m height from ground level and at all locations as directed including preparing surfaces for painting by any approved means, scaffolding, cleaning and curing etc. complete as directed by Engineer-in-charge By using acrylic based exterior paint 21 Extra over item no. CS-PN-1 and CS-PN-2 for preparing the old surface for white/colour wash or dry/water bound distemper including scrapping the old paint with wire brush, blades or sand papers upto original surface, filling in the cracks and loose patches etc. with C.M 1:3 etc. complete as directed. 22 Extra over item no. CS-PN-3 and CS-PN-6 for preparing and Finishing plastered wall surfsce/concrete surface,steel or woodsurfaces in line and level acrylic(oil bond)distemper/synthetic enamal paint or plastic emulsion paint by scrapping/removing the old paint if any with wire brush or blades and rubbing with sand papers as requird, filling in the cracks in cement morter 1:3 and loose patches etc. with C.M 1:3. appling the whole surface with mixture of whiting powder or plaster of paris and double boiled insees oil of premium quality or second quality synthetic enamal paint,filling the cracks with premium quality putty or hard glue in case of wall work, rubbing down and even up the surface by any approvd means etc complete as directed by Engineer-in-charge. 23 Providing and constructing raised platform of 750 mm wide and 600 to 750mm high using minimum 40mm thick polished kadappa stone slab of approved quality at top, supported by both side polished, 40mm thk. and 700mm wide kadappa spaced at not more than 1200mm clear, including polished kadappa facia of min. 75mm hight with champhered at the top edges, making opening for sink and fixing the same in position, preparing the surface and levelling in the desired line, machine cutting, jointing in approved adhesives, leveling, smooth cement plastering along the sides to match the existing surface in cement mortar, filling the joints with pigment mixed with cement, cleaning, finishing, curing etc complete as directed by Engineer In Charge. (Sink will be paid separately) 24 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :610x510 mm bowl depth 200 mm 25 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :610x460 mm bowl depth 200 mm 26 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :470x420 mm bowl depth 178 mm 27 Providing and fixing cuddapah stone slab for kitchen platform of approved type and design 30 mm to 40 mm thick in cement mortar 1: 4 including providing and fixing border patti on front edge, filling joints, curing, cleaning etc. complete. 28 Providing and laying polished natural stone as specified below (Machine cut) of an approved quality and size for paving /flooring in plain and/or diamond /approved pattern including cement mortar bedding of 25 mm thick in 1:4 proportion, cement float, machine cutting, dressing, leveling, jointing, filling the joints with neat cement slurry or with required pigment, machine polishing at site, curing, finishing, etc complete as directed by Engineer In Charge. 25 to 30 mm thk. Kota stone of size 0.430m x0.56m (17x22) 29 Providing and laying 8mm thk. ceramic tiles as specified below conforming to I.S.15622-2006 for flooring of an approved, quality, make, size and pattern /design, for flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, neat cement float, cutting, leveling, jointing, filling the joints by neat cement slurry or approved colour grout, curing, finishing etc complete as directed by Engineer In Charge.Light/Dark coloured antiskid / matt ceramic tiles 30 Providing and laying 600 x 600 x 8 mm thk. vitrified tiles as specified below conforming to I.S.15622- 2006 with water absorbtion less than 0.08% for flooring of an approved, quality, make and pattern /design for flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cutting, leveling, jointing, filling the joints by neat cement slurry or approved colour grout, curing, finishing etc complete as directed by Engineer In Charge Light/Darkcoloured glazed vitrified tiles 31 Providing and laying Indian patent stone flooring 40 mm thick with M-15 grade concrete using 6 mm to 20 mm metal over bedding laid in proper grade and slope or over the slab, including compaction, marking lines, to give appearance of tiles as per the approved pattern, finishing smooth with cement slurry as mentioned below, curing etc. complete. In plain natural/ grey colours 32 Providing and fixing 8mm thk. ceramic tiles as specified below conforming to I.S. 15622-2006 of approved quality, pattern and colour for dado in the wet area including preparing the surface and levelling in the desired line, backing of 20 thk. cement mortar in porportion 1:3 with approved waterproofing compound, square cut top edge or chamfered top edge in cement mortar 1:3, cement float, machine cutting, leveling, jointing, filling the joints with neat cement slurry or approved colour grout, finishing, curing etc complete as directed by Engineer In Charge Light /Dark coloured glazed ceramic tiles 33 Providing and fixing polished natural stone tiles as specified below of approved quality, pattern and colour for sill and jambs including preparing the surface and levelling in the desired line, cement mortar 1:3 bedding or backing, cement float, machine cutting, leveling, jointing, smooth cement plastering along the sides to match the existing surface in cement mortar 1:3, filling the joints with neat cement or pigment mixed with cement, finishing, curing etccomplete as directed by Engineer In Charge 18mm thk. green marble for width upto 150 mm 34 Providing and fixing polished natural stone tiles as specified below of approved quality, pattern and colour for sill and jambs including preparing the surface and levelling in the desired line, cement mortar 1:3 bedding or backing, cement float, machine cutting, leveling, jointing, smooth cement plastering along the sides to match the existing surface in cement mortar 1:3, filling the joints with neat cement or pigment mixed with cement, finishing, curing etccomplete as directed by Engineer In Charge18mm thk. green marble for width upto 300 mm 35 Providing and fixing in position UV resistant, fire retardant, virtually unbreakable and temperature resistant (-40° C to +130° C) Polycarbonate corrugated sheet of 2mm thickness for roof of approved make to match the roof profile at any height with G.I. J hooks bolts of G.I. clamps nuts & bolts or with self drilling fastener and EPDM washer etc. complete as directed. 36 Providing and fixing UV resistant selffit UPVC pipes of approved make for Rainwater downtakes confirming to IS 13592:1992 Type A suitable for 4kg/sqcm pressure for following pipe diameters including rain water receiving recess with pvc plug bend necessary fittings such as offsets shoes, fixing the pipes on wall with clips filling the joints with solvent/cement and necessary scafolding etc. complete as directed by Engineer In Charge 100mm dia 37 Providing, detailing, fabricating and fixing at desired location using hot rolled sections and MS Plates of grade Fe 250 as per specifications and approved fabrication drawings (which are to be prepared by Contractor and got approved from Engineer), transporting to site and erecting structural steel members for all heights & at all levels including provision of necessary erection bolts, fixing bolts, nuts, washers, cleats, stiffeners, gussets, base plate, and all necessary fixtures and operations like preheating as per specifications, straightening, bending, cutting, drilling, grinding, machining if specified, welding, grinding and removing the welding burr and preparing surface for painting with wire brush cleaning and applying two coats of epoxy red oxide zinc phosphate primer of 30 microns each and two coats of Epoxy Corrosion Resistant Enamel paint of 30 microns after fabrication including touching up with spray painting after erection etc complete as directed by Engineer In Charge. (The qty. for this item shall be measured for gusset plates, base plates, bolts in M.T.) 38 Providing and Fixing MS Safety grill of weight specified below for windows as per design including fabricating the grill using M.S. square / round bar, flats and angles including painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of approved colour and brand etc complete as directed.Grill weighing 10 to 15 kg / sqm 39 Providing and fixing best quality C.P. Teak wood frame for doors, windows and ventilators size greater than 50mm x 50mm including intermittent supports if required, all moulding, rebating, jointing, hold fasts of MS flats of minimum size 25 x 3 mm, having length of 225 mm for doors & 150 mm for windows and finishing with 3 coats of French polish or one coat of primer and synthetic enamel paint in two coats as directed etc. complete as directed. 40 Providing and applying water proof (melamine) polishing to the new or old wood work in two coats including knotting, preparing the surface by scrapping, scaffolding etc. complete as directed. 41 Providing & applying readymade wax polish to the new or old work in two coats including knotting, preparing the surface by scrapping, scaffolding etc. complete as directed. 42 Providing and fixing superior quality factory made single or double leaf Phenol Bonded solid core flush door shutters commercial type hot pressed conforming to IS:2202 (Part I,II) 1991 including 12 mm thk teak wood lipping all around with one coat of primer, putty and 2 coats of synthetic enamel paint on both faces etc. complete as directed. (Hinges, aldrop & standard door hardware to be paid separately) 35mm thick shutter 43 Extra for providing and fixing 3mm thk. veneer with three coats of french polishing instead of synthetic enamel painting including all material and labour. 44 Extra for Providing and fixing decorative 1.0 mm thick laminate like decolam or formica laminate or any other aproved brand, complete with approved glue etc. 45 Providing and fixing in position three track aluminum window of extruded modular and anodized aluminum sections of approved make and of size 92 mm x 45.5 mm x 1.5 mm thk (wt 1.659 kg/Rm) for bottom and 92 mm x 31.75 mm x 1.3 mm thk. (wt 0.933 kg/Rm) for top and sides mounted on anodized aluminum rectangular frame of size 100mm x 40mm x 1.3mm.(Wt 0.976 kg/m) The shutter comprising of bearing bottom and top of size 40mm x 18 mm x 1.25 mm thk (wt. 0.417 Kg/Rm) Interlocking section of size 40mm x 26.7 mm x 1.10 mm thk. (Wt. 0.469 kg./Rm) and hand sides of 40mm x 18mm x 1.25 mm thk (wt. 0.417kg/Rm) with 5 mm thick plain / frosted / tinted glass fixed in shutter including approved quality neoprene gasket, fixtures, fastenings and accessories like PVC rollers, PVC weep holes, locks, handles etc. complete as directed by Engineer In Charge. (Note: anodic film must not be less than 15 microns i.e. AC-15 as per IS, the anodizing must be scaleted by keeping the anodized section in boiling de-anodized water for a period of one hour) 46 Providing and fixing in position four track aluminum window of extruded modular and anodized aluminum sections of approved make and of size 122.2 mm x 45.5 mm x 1.3 mm thk (wt 1.829 kg/Rm) for bottom and 122.2 mm x 31.75 mm x 1.2 mm thk. (wt 1.093 kg/Rm) for top and sides mounted on anodized aluminum rectangular frame of size 127mm x 25.4mm x 1.3mm(1.052 kg/m) The shutter comprising of bearing bottom and top of size 40mm x 18 mm x 1.25 mm thk (wt. 0.417 Kg/Rm) Interlocking section of size 40mm x 26.7 mm x 1.10 mm thk. (Wt. 0469 kg./Rm) and hand sides of 40mm x 18mm x 1.25 mm thk (wt. 0.417kg/Rm) with 5 mm thick plain / frosted / tinted glass fixed in shutter including approved quality neoprene gasket, fixtures, fastenings and accessories like PVC rollers, PVC weep holes, locks, handles etc. complete as directedby Engineer In Charge.(Note: anodic film must not be less than 15 microns i.e. AC-15 as per IS, the anodizing must be scaleted by keeping the anodized section in boiling de-anodized water for a period of one hour) 47 Providing and fixing in position aluminum louvered window with anodised aluminum frame of approved make and of size 40mm x 20mm x 2.0mm (wt. 0.605 kg/Rm) including adjustable aluminum frame, 4 to 6mm thk.frostedglass, fixtures and fastenings etc. complete as directed by by Engineer In Charge. 48 Providing and fixing SS Mosquito mesh in anodised (anodic film must not be less than 15 microns i.e. AC-15 as per IS, the anodising must be scaleted by keeping the anodized section in boiling de-anodized water for a period of one hour) aluminium shutter fixed in sliding / openable / fixed windows conforming to IS:1948-1961 as per drawing and directed by Engineer In Charge.(Note: For Aluminum Sections, total weight shall be upto 3.5 kg/sq.m.) 49 Providing and fixing mortise/night lock of approved make manufactured as per IS:2209 and 6607 and as described below for doors with necessary fixtures and materials and labour etc. complete Chromium plated Brass mortice/night latch and lock 50 Providing and fixing peep hole as described below manufactured as per IS wherever applicable for doors with necessary fixtures and materials and labour etc. complete.Brass peep hole 51 Providing and fixing door stopper as described below of approved make manufactured as described below and as per IS:1823- 1992 for doors with necessary materials and labour cost etc. complete.Brass (First Quality) door stopper 52 manufactured as per relevant IS for door & windows with necessary materials and labour costs etc. complete.Standard brass hinges 75 mm Long 53 manufactured as per relevant IS for door & windows with necessary materials and labour costs etc. complete.Standard brass hinges 100 mm Long 54 manufactured as per relevant IS for door & windows with necessary materials and labour costs etc. complete.Standard brass hinges 125 mm Long 55 manufactured as per relevant IS for door & windows with necessary materials and labour costs etc. complete.Standard brass hinges 150 mm Long 56 manufactured as per relevant IS for door & windows with necessary materials and labour costs etc. complete.Standard Stainless Steel hinges 75mm long 57 manufactured as per relevant IS for door & windows with necessary materials and labour costs etc. complete.Standard Stainless Steel hinges 100mm long 58 manufactured as per relevant IS for door & windows with necessary materials and labour costs etc. complete.Standard Stainless Steel hinges 125mm long 59 manufactured as per relevant IS for door & windows with necessary materials and labour costs etc. complete.Standard Stainless Steel hinges 150mm long 60 Providing and fixing aldrops of 16 mm diameter bars manufactured as per IS:2681-1991, wherever they apply for doors and windows with necessary materials and labour etc. complete.Standard Brass Aldrops 250 mm long. 61 Providing and fixing aldrops of 16 mm diameter bars manufactured as per IS:2681-1991, wherever they apply for doors and windows with necessary materials and labour etc. complete.Standard Brass Aldrops 300 mm long. 62 Providing and fixing aldrops of 16 mm diameter bars manufactured as per IS:2681-1991, wherever they apply for doors and windows with necessary materials and labour etc. complete.Standard Stainless Steel make Aldrop 250 mm long 63 Providing and fixing aldrops of 16 mm diameter bars manufactured as per IS:2681-1991, wherever they apply for doors and windows with necessary materials and labour etc. complete.Standard Stainless Steel make Aldrop 300 mm long 64 P/F iron oxidized tadi of 12mm dia., 200mm long. 65 P/F iron oxidized tadi of 12mm dia., 250mm long. 66 P/F standard brass aldrop of 12mm dia., 200mm long. 67 P/F standard brass aldrop of 12mm dia., 250mm long. 68 P/F stailess steel aldrop of 12mm dia., 200mm long 69 P/F stailess steel aldrop of 12mm dia., 250mm long 70 conforming to IS:204-1992 (Part I,II) for doors & windows with necessary materials and labour etc. complete.Standard Anodised AluminiumTower bolt 100 mm long. 71 conforming to IS:204-1992 (Part I,II) for doors & windows with necessary materials and labour etc. complete.Standard Anodised AluminiumTower bolt 150 mm long. 72 conforming to IS:204-1992 (Part I,II) for doors & windows with necessary materials and labour etc. complete.Standard stainless steel Tower bolt 100 mm long. 73 conforming to IS:204-1992 (Part I,II) for doors & windows with necessary materials and labour etc. complete.Standard stainless steel Tower bolt 150 mm long. 74 Providing and fixing handles as described below, manufactured as per IS:208-1992 for doors and windows and with necessary materials and fixtures like screws etc. and all labour etc. complete.Standard Brass Handles 100 mm long. 75 Providing and fixing handles as described below, manufactured as per IS:208-1992 for doors and windows and with necessary materials and fixtures like screws etc. and all labour etc. complete..Standard Brass Handles 125 mm long. 76 Providing and fixing handles as described below, manufactured as per IS:208-1992 for doors and windows and with necessary materials and fixtures like screws etc. and all labour etc. complete.Standard Brass Handles150 mm long. 77 Providing and fixing handles as described below, manufactured as per IS:208-1992 for doors and windows and with necessary materials and fixtures like screws etc. and all labour etc. complete.Standard Stainless Steel150 mm long. 78 Providing and fixing stainless steel door chain including necessary stainless steel screws etc complete as directed by Engineer In Charge. 79 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. 80 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid 81 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. 82 Providing and fixing 100 mm sand cast Iron grating for Nahani/Floor trap. 83 Internal work - Exposed on wall -Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.15 mm dia nominal bore 84 Internal work - Exposed on wall-Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.20 mm dia nominal bore 85 Internal work - Exposed on wall- Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.25 mm dia nominal bore 86 Internal work - Exposed on wall -Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.32 mm dia nominal bore 87 External work -Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15 mm dia nominal bore 88 External work -Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm dia nominal bore 89 External work -Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore 90 External work -Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore 91 Providing and fixing brass bib cock of approved quality :15 mm nominal bore 92 Providing and fixing brass bib cock of approved quality :20 mm nominal bore 93 Providing and fixing brass stop cock of approved quality :15 mm nominal bore 94 Providing and fixing brass stop cock of approved quality :20 mm nominal bore 95 Providing and fixing gun metal gate valve with C.I. wheel of approved 25 mm nominal bore 96 Providing and fixing gun metal gate valve with C.I. wheel of approved 32 mm nominal bore 97 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore 98 Providing & fixing in position `Jacquar Continental make CP Jet Spray with flexible CP supply pipe, and all other accessories, complete 99 Providing and fixing brass CP angle cock for mini geyser of Metro,seiko or other equivalent approved make. 100 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 101 Demolishing brick work in lime or cement mortar including plaster, paint, etc. manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 102 Removing doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :Of area 3 sq. metres and below 103 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all loads including all lifts involved. 104 Removing and refixing G.I. pipes of any size with all new fittings if necessary complete including cleaning and painting. 105 Removing and refixing drain pipe (soil, waste water, ventilating or rain water) of any size with all fittings including cleaning pipe before fixing and painting as directed. 106 Removing mosaic, cement marble, granites non-slippery, tandur, kotah, shahabad stone or Indian Pattern stone, glazed tiles in flooring and dado including bedding brick bat coba etc., and delivering materials in Ward Office and carting away unserviceable materials. 107 Removing and refixing existing door or window with frames and shutters, making good the damaged brick work and applying 3 coats of Syn. Ena. paint. 108 Removing existing door or windows with frame and shutters and making good etc. to the existing surface. 109 Removing shutters of doors and windows without frame. 110 Removing soil pan, urinal, wash basin and sink of any type, size, make and brand including its bedding drainage fitting. etc. complete 111 Removing G.I. pipes internal exposed of any size including fittings etc complete 112 Application of Corrosion Inhibitor: Providing & applying One coat ofConcrete Penetrating Corrosion Inhibitor (Surface applied) which works on Bipolar Inhibition Mechanism on entire concrete surface to be repaired by using brush or spray at 250 ml per Sq.Mt./Coat or as per manufacturer’s specification and prior to application of first coat of anti corrosive coating to reinforcement. 113 Shear Connectors: Make 10/12 mmdia holes using heavy duty electrically operated hammer drills in the concrete of RCC members to a depth of about 75 mm at 500 mmc/cor at suitablegrid inzig-zag fashion, clean the holes using air jet and fix pre- fabricated 100 x 50 mm L-shape 8 mm diarebar using Anti Corrosive protective coatingso that 75 mm out of 100 mm is inserted inside the concrete and 25 mm remain outside along with 50 mm bend. The shearconnectors are used to tie the additional reinforcement bars 114 Additional Reinforcement: Cutting, bending and fixing in position steel reinforcement of specified/required sizes and shapes in the form or main rebars, stirrups & rings, distribution rebars etc., and tying them to shear connectors using GI binding wire. The additional rebars should be coated with TWO coats of Anti Corrosive protectivecoating & dry sand to be sprinkled on second coat. 115 Bond Coat: Providing & applying One coat of structural grade epoxy bond coat by brush conforming to ASTM-C-882- 87 to the prepared concrete surface to be repaired / strengthened. This isapplied prior to the application of polymer repair mortar / epoxy mortar / Microconcrete to have monolithic action between old concrete surface and new concrete surface 116 Repair with Polymer Modified Mortar (PMM): Repairs to the deteriorated / damaged areas of RCC elements in the structure shall be carried out by using powder Polymer Modified repair mortar. The polymer modified mortar is applied when the epoxy bonding coat is still tacky. In one application25 mm thickness shall be built.Subsequent layer shall be built with one bond coat of Polymer modified cementslurry. The polymer modified repair mortar shall be mixed, applied and cured as per technical 117 Chipping /removing loose concrete upto reinforcement bars, without damaging the reinforcement, removing all the loose materials and to make all the exposed surfaces free from oil, dust and all impurities etc complete. 118 Removing corrosion of steel reinforcement by mechanical means like wire brushing, chipping to remove loose rust and then applying rust removal solution by using brush application, leaving the surface for at least 15 to 30 minutes, then removing loose materials by scrubbing or with brush. After detachment of loose scales reddish rusted surface is still left exposed, this has to be retreated or as per approved manufacturers specifications. (Note:- Consider surface area of concrete for payment 119 Providing waterproofing treatment through specialized agencies as per their specifications to the flooring of water closets, bathrooms, kitchen, nahanies, washing places, sanitary blocks etc. by giving INJECTIONS with cement solution with water proofing compound into the floor slab so as to make it consistent, homogeneous and impervious against leakage, seepage etc. The sunk portion shall then be covered with brickbat waterproof coba in 1:5 c.s. of required thickness with necessary gradient for easy flow of water. Finally the floor shall be covered with joint less waterproof cement plaster in 1:3 c.s. 12 mm to 15 mm thick finished rough for receiving tiles. The average thickness of complete treatment shall not be less than 100 mm. The soil pan area will not be deducted. (After completion of work leakage test shall be carried out after impounding the water for 7 days without any extra cost. The actual treated area will be measured and paid for). 120 Providing and applying two coats of asian paints plaster coat or equivalent material (In cost and properties) to any surface, at all height and locations as directed including scaffolding, cleaning and preparing surfaces for painting with broom, coir and sand paper if necessary or by any other approved means etc. complete as directed by Engineer-in-charge. 121 Providing and fixing all sides polished natural stone as specified below of approved quality, pattern, colour and thickness for door and window frames / architraves including preparing the surface and levelling in the desired line, machine cutting, jointing in approved adhesives, leveling, smooth cement plastering along the sides to match the existing surface in cement mortar, filling the joints with pigment mixed with cement, cleaning, finishing, curing etc complete as directed by Engineer In Charge. With Kadappa stone 122 Providing and fixing all sides polished natural stone as specified below of approved quality, pattern, colour and thickness for door and window frames / architraves including preparing the surface and levelling in the desired line, machine cutting, jointing in approved adhesives, leveling, smooth cement plastering along the sides to match the existing surface in cement mortar, filling the joints with pigment mixed with cement, cleaning, finishing, curing etc complete as directed by Engineer In Charge. With green marble. 123 Providing and fixing 6mm thick Non-asbestos high impact Polypropylene reinforced cement corrugated sheet of approved make conforming to IS:14871-2000 laying the same in position as per the stipulation in IS:3007-1991 using 8m diapoly mercoated iron Lor Jhook bolts, galvanized iron & bituminous washers, or self drilling fastener sand EPDM washers, galvanized iron clamps, nuts and bolts etc. complete and as directed.(Net Area covered by sheeting will be measured. Laps will not be paid separately 124 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. 125 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White 126 Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : White solid plastic seat with lid 127 Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : Coloured (other than black & white) solid plastic seat with lid 128 Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. 129 Providing and fixing P.V.C.waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia 130 Providing and fixing P.V.C.waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia 131 Providing and fixing G.I. pipes of C class, complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 15mm dia. Nominal bore 132 Providing and fixing G.I. pipes of C class, complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 20mm dia. Nominal bore 133 Providing and fixing G.I. pipes of C class, complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 25mm dia. Nominal bore 134 Providing and fixing G.I. pipes of C class, complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 32mm dia. Nominal bore 135 Providing and fixing G.I. pipes of C class, complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 40mm dia. Nominal bore 136 Providing and fixing G.I. pipes of C class, complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 50mm dia. Nominal bore 137 Waste coupling 38mm dia of 83mm length and77 mm breadth weighing not less than 60gms 138 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore 139 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore 140 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore 141 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore 142 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore 143 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter 144 Providing and fixing C.P. brass bib cock/stop cock of approved quality conforming to IS:8931 : 15 mm nominal bore 145 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 146 Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete. 147 Providing and fixing Stainless Steel Netting 26 B.W.G., 5 to 6 Squares per sq. cm. including beading etc. complete. 148 Providing and fixing 12 mm thick Nova teak super particle board including nails,screws etc. complete. 149 Providing & fixing 18 mm thick ply wood for furniture work with necessary adhesive pins, if required etc. complete. 150 Providing & fixing 12 mm thick ply wood for furniture work with necessary adhesive pins, if required etc. complete. 151 Providing & fixing 8 to 10 mm thick ply wood for furniture work with necessary adhesive pins, if required etc. complete. 152 Providing & fixing 4 mm thick ply wood for furniture work with necessary adhesive pins, if required etc. complete. 153 Replacing the old damaged fittings by providing and fixing New fittings and old removed fittings to be returned to the Township Civil Stores, etc. as directed. M.S. Hold and stapples 2” to 4” size. 154 Replacing the old damaged fittings by providing and fixing New fittings and old removed fittings to be returned to the Township Civil Stores, etc. as directed. M.S. L plate 4” x 4” or 6” x 6” size. 155 Replacing the old fittings by providing and fixing New Aluminum fittings with necessary Screws and old removed fittings to be returned to the Township Civil Stores, etc. as directed. Aluminium Hinges 3” to 4” long. 156 Replacing the old fittings by providing and fixing New Aluminium fittings with necessary Screws and old removed fittings to be returned to the Township Civil Stores, etc. as directed. Aluminium Tower Bolts 100 mm. 157 Replacing the old fittings by providing and fixing New Aluminium fittings with necessary Screws and old removed fittings to be returned to the Township Civil Stores, etc. as directed. Aluminium Handles 100 mm 158 Replacing the old fittings by providing and fixing New Aluminium fittings with necessary Screws and old removed fittings to be returned to the Township Civil Stores, etc. as directed. Aluminium Aldrops 12 long. 159 Replacing the old fittings by providing and fixing New Aluminium fittings with necessary Screws and old removed fittings to be returned to the Township Civil Stores, etc. as directed. Aluminium Locking Kunda. 160 Refixing the shutters of Doors/windows/ventilators as directed inclusive of fixtures, fasteners and fixing with new screws etc. complete. 161 Providing and fixing with new teak beading 12 mm square. 162 Providing and fixing aluminium framed door with hardner Laminated sheet 4mm thick (Bakelite composite panel) with outer aluminium frame of size A-section 50mmx20mmx1.5mm (Wt.0.571kg/M) using heavy duty steel hinges100mm, aluminium handle125mm, aluminium tadi200mm, alu. tower bolt100mm etc. complete. 163 Providing & fixing Godrej Night Latch Lever inside night latch including removing and refixing of night latch etc.complete as directed. 164 Glazing with best sheet glass (ground / frosted / plain) 4 mm thick 6.5 to 7.5 kg per sq.m. with tacks and colour putty, etc. complete. 165 Glazing with best quality with sheet glass (ground / frosted / plain) 5 mm thick (above 0.5 sqm and upto 1.0 sqm). 166 Extra for Providing and fixing decorative 1.0 mm thick laminate like decolam or formica laminate or any other aproved brand, complete with approved glue etc. 167 Providing and fixing ball valve (Plastic) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore (Prayag Make) 168 Providing and fixing CCTW beading / lipping of size 25 mm to 40mm for flush door shutters and at other locations including finishing etc.complete. 169 Providing and fixing galvanized tees, elbows, bends with or without excavation 12 mm dia. 170 Providing and fixing galvanized tees, elbows, bends with or without excavation 20 mm dia. 171 Providing and fixing galvanized tees, elbows, bends with or without excavation 25 mm dia. 172 Providing and fixing galvanized tees, elbows, bends with or without excavation 32 mm to 38 mm dia. 173 Providing and fixing galvanized tees, elbows, bends with or without excavation 50 mm dia. 174 Providing and fixing plug of size 12 mm. 175 Providing and fixing plug of size 20 mm. 176 Providing and fixing plug of size 25 mm. 177 Providing and fixing plug of size 32 to 38 mm. 178 Providing and fixing plug of size 50 mm. 179 Providing and fixing nipples of size 12 mm. 180 Providing and fixing nipples of size 20 mm. 181 Providing and fixing nipples of size 25 mm. 182 Providing and fixing nipples of size 32 to 38 mm. 183 Providing and fixing nipples of size 50 mm. 184 Providing and fixing coupling sockets and check nuts of size 12 mm to 20 mm dia. 185 Providing and fixing coupling sockets and check nuts of size 25 mm to 38 mm dia. 186 Providing and fixing coupling sockets and check nuts of size 50 mm dia. 187 Reducing coupling for sockets 12 mm to 20 mm dia. 188 Reducing coupling for sockets 25 mm to 30 mm dia. 189 Reducing coupling for sockets 50 mm to 75 mm dia. 190 Providing & fixing barrel Nipples/connectors of required length up to 300 mm of size 12 to 20 mm. 191 Providing & fixing barrel Nipples/connectors of required length up to 300 mm of size 25 to 32 mm dia. 192 Providing and fixing W.I. / G.I. unions after removing old damaged union of size 12 mm. 193 Providing and fixing W.I. / G.I. unions after removing old damaged union of size 20 mm. 194 Providing and fixing W.I. / G.I. unions after removing old damaged union of size 25 mm. 195 Providing and fixing W.I. / G.I. unions after removing old damaged union of size 32 to 38 mm. 196 Providing and fixing W.I. / G.I. unions after removing old damaged union of size 50 mm. 197 Providing and fixing new chromium plated 4 long pillar type cock (ISI mark) with deluxe knob for wash basin or sink inclusive of removal of old tap and depositing the same in Township Civil Stores 12 mm size complete. 198 Providing & fixing heavy duty chromium plated brass concealed type stop cock of ISI mark of 12 mm size etc. complete. 199 Providing and fixing heavy duty Chromium plated brass bib tap, concealed type of ISI mark of 12 mm size etc. complete. 200 Providing & fixing following items in flushing cistern after necessary inspection and as per requirements : Rubber bush. 201 Providing & fixing following items in flushing cistern after necessary inspection and as per requirements : Pull Chain. 202 Providing & fixing following items in flushing cistern after necessary inspection and as per requirements : C.I. Syphon handle. 203 Providing & fixing following items in flushing cistern after necessary inspection and as per requirements : Rubber Washer. 204 Providing & fixing following items in flushing cistern after necessary inspection and as per requirements : PVC tank handle. 205 Providing & fixing following items in flushing cistern after necessary inspection and as per requirements : Bottom rubber washer. 206 Providing and fixing ball valve (Plastic) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore (Prayag Make) 207 P.V.C. ball cock of ½” size. 208 Providing and fixing W.I. clamps to G.I. Pipes 12 mm to 32 mm as directed. 209 Providing & fixing C.I. brackets of approved type for any kind of wash basin / sink / flush tank. (per pair) 210 Providing & fixing chromium plated or aluminium grating 80 to 150 mm dia. for nahani trap etc. complete. 211 Providing and laying granite stone 20 mm to 25 mm thick in required shade, set in 1:4 CS with cement float and with cement pointing laid to proper slope if required finished and cleaned of all strains complete. 212 For Health faucet with 2way bib cock (jaquar - continental or equivalent) 213 Providing and fixing 75 mm nominal outside diameter UPVC soil/waste pipe as per I.S. 13592 : 1992 or latest, including all necessary fittings such as bends, tees, single/double junction, sloted vents, offsets on wall with clips filling the joints with solvent cement incl. necessary scaffolding etc. complete. 214 Providing and fixing 110 mm diameter UPVC soil/waste pipe as per I.S. 13592 : 1992 or latest, including all necessary fittings such as bends, tees, single/double junction, sloted vents, offsets on wall with clips filling the joints with solvent cement incl. necessary scaffolding etc. complete. 215 Providing and fixing 110 mm UPVC P trap including w.c. bend connector with necessary fittings, filling the joints with solvent cement including necessary scafolding etc. complete as per s 13592:1992 or latest. 216 Making holes in 100 mm to 150 mm dia. In brick / concrete / rubble walls for drainage pipes, fittings etc. and making good the same with C.M. 1:3 or C.C 1:2:4 and finishing on both sides with cement plaster. 217 Providing & fixing 25 mm dia. G.I. pipe water spout including making hole & making good the same including bends as directed. 218 In addition to painting, for providing & applying Asian paints texture paint as per manufactures specifications. 219 Providing 2 way bibcock with handshower etc. Complete 220 For Hand shower in WC (ABS) chrome plated with 8mm dia. 1.2M long flexible tube and wall hook. (Jaguar or equivalent) 221 Making easy doors, windows, Ventilators etc. by cleaning of site. 222 Removing door Latch for Repair/adjustment and refixing etc complete. 223 Removing door closer for Repair/adjustment and refixing etc complete. 224 Repairing of C.I., G.I., PVC flush tank and adjusting to avoid overflow making it operationable etc. complete excluding fittings as directed. 225 Clearing chock up of W.C., bath, kitchen mori, etc. and ensuring proper flow of waste water etc. complete. 226 Removing G.I. Pipes of any size with all fittings complete. 227 Refixing G.I. Pipes of any size with all fittings complete. 228 Labour for removing soil pan (Indian or European Style including its bedding drainage fitting) / urinal / flush tank / wash basin or sink with brackets, etc. including disconnecting (water & drainage fittings) etc. & depositing the reuseable materials in Township Civil Stores. 229 Labour for refixing soil pan (Indian or European Style) / urinal / flush tank / wash basin or sink including fixing the same with brackets, etc. and also reconnecting the water & drainage fittings, etc. complete. 230 Removing the small trees from wall portion from the roots and depositing the debris as shown inclusive of finishing the surface with C.S. plaster as directed. 231 Removal drain pipes (soil, waste, water, ventilating and rain water pipes) of any size, with all fittings. 232 Providing and fixing waste coupling for SS sink of required size with rubber gasket and any other necessary fitting. Nirali or equivalent make 233 Providing and fixing SS hot pipe for gyser 1.5 feet long 234 Providing and fixing SS hot pipe for gyser 2 feet long 235 P & F Jet spray holder as direted by EIC 236 P & F Jet spray flexible SS pipe as direted by EIC 237 Providing & Fixing waste Coupling along with all necessary fittings as directed by EIC. 238 Supply Of Un Skilled Labour 239 Supply Of Semi Skilled Labour 240 Supply Of Skilled Labour
