|
Tender For Provision Of Dsc Guard Post At Af Stn Samana Under Ge (Af) Gamnagar No 1; 1 Excavation in trenches not exc 1.5 m wide and n.exc 1.5m in depthfor foundation / fixing pole / laying cable and pipe line etc or n. exc 10 sqm on plan and getting out in soft / loose soil complete all as specified and directed. 2 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed. 3 Returning filling in any type soil incl spreading, levelling, watering, and well ramming in layers complete all as specified and directed. 4 Removing excavated material of soils n. exc 50 mtr and depositing where directed at a level n. exc 1.50 m above the starting point complete all as specified and directed. 5 M& L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. 6 M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in fdn filling and mass concrete complete all as specified and directed. 7 M&L for 75mm thick cement concrete type D2 (1:4:8) using 40mm graded stone aggregate as in subbase complete all as specified and as directed. 8 M&L for 75 mm thick Cement concrete type C- 2, 1:3:6 (40mm graded aggregate) as plinth protection/hardstanding etccomplete all as specified and as directed. 9 M&L for Green Marble work 15 to 18 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in coloured cement (1:2) using marble dust with admixture of pigment to match with marble shade laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. 10 S&F CRS TMT bars 10 mm dia and over (Fe-500D), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less then 0.9 mm dia or securing with clips complete all as specified and as directed. 11 S&F CRS TMT bars 6mm to 8mm dia and over (Fe-500D)cut to length bent to shape required including cranking bending spirally and binding with and including mild steel wise (annealed) not less than 0.9 mm dia complete all as specified and asdirected. 12 M&L RCC M-30 design mix (Using 20 mm graded stone aggregate) as in foundation, including rafts, footings, foundation beams, plinth beams, clumns, pillars piers, posts etc all as specified and directed. 13 M&L RCC M-30 design mix (Using 20 mm graded stone aggregate) as in columns, pillars piers, posts and struts etc all as specified and directed. 14 M&L RCC M-30 design mix (Using 20 mm graded stone aggregate) as in Beams, cantilevers,bressummers, lintal and chajja etc all as specified and directed. 15 M&L RCC M-30 design mix (Using 20 mm graded stone aggregate) as in slabs supported on walls, beams, and columns in floors, foors, landings, balconies, canopies, deck slabs and in shelves and the likeetc all as specified and directed. 16 Form work to flat sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any)of foundation, plinth beams and similar work; vertical or to batter complete all as specified and directed. 17 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. 18 Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed. 19 Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed. 20 M&L for providing precast cement concrete (1:3:6) (using 20mm graded stone aggregate) solid building blocks exe 10 cm thick, in width (with plain or inter locking joints as directed) setting in CM 1:6 complete inwall or pillars or kerbstone all as specified and directed. 21 M & L for rendering 15 mm thick in cement mortar 1:6 over PCC block masonry/concete wall surfaces, finished the surfaces even and smooth complete all as specified and directed. 22 M & L for rendering 15 mm thick in cement mortar 1:4 over PCC block masonry/concete wall surfaces, finished the surfaces even and smooth complete all as specified and directed. 23 M&L for rendering 10mm thick in CM 1:3 on concrete surface of slab, beam & ceiling surfaces finished even and smooth without using extra cement all as specified and directed 24 Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) and any pattern with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces walls/fins/facia/soffit/chajja etc complete all as specified and directed 25 M&L for preparation of new plastered surface of wall and applying two coats of oil bound Distemper, complete all as specified & directed. 26 M&L for preparation of new plastered surfaces of ceiling and applying two coats of oil bound Distemper, complete all as specified and directed. 27 M&L for plastering 10mm thick on concrete surface in CM 1:4, finishing the surface even and smooth without using extra cement, including mixing only liquid water proofing compoundas per manufacture instruction complete all as specified and directed.Note: WPC will be measured & paid separately. 28 Supply only integral water proofing chemical @ 200ml/Bag of cement complete all as specified and directed. 29 M&L for waterproofing treatment by water proofing liquid after proper cleaning of the new surface free of dust and applying the first coat (By Brush only)@ 4-4.5 Sqmt/Ltr, allowing it to dry for 24 hrs and applying the second coat over it on horizontal and vertical surface complete all as specified and directed. Note: Application shall be carried out through authorised applicator of manufacturer only and as per guidelines of Manufacturer strictly. Make: Sunshield 100 of M/s Choksey, FOSROC or equivalent approved by GE. 30 S&F aluminium three track Powder coatedof any colour ( thickness of powder coating not less than 50 micron) sliding window with three sliding shutter , the size of outer frame three track92 x 31.5x 1.20mm ( using two track for glazed window shutter and one track for wire gauged ) ,thesectionshutter size 37x 18x 1.2mm) and glazing with 4 mm thickglass ( plain/floated) including all-aroundsuitablerubber gasket andSS wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminium flatand inserted in the frame ofshutterwith tracking arrangement each sliding window shall be provided with one number handle includinglocking arrangement & 2 numbers sliding rollers of nylon with including all necessary fittings complete all as specified and as directed. 31 S&F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates,Fe-290 (Gde E 165)etc as door frame, steel gate,sink, hand wash basin and cooler stand etc complete all as specified and as directed. 32 S & Ffor factory made flush shutters,30mm thicksolid core construction, with block board core and plywood face panels, with 0.90mm thick decorative laminate type 1, commercial type on both sides of surface finish, colour as approved, fixed with approved adhesive as per manufacturers instructions complete all as specified and directed. 33 S&F for 35 mm thick factory made second class hardwoodGlazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass / gauge, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkhats complete all as specified and directed. 34 S&F 100 mm size Stainless steel butt hinges medium weight, fixed to chowkhat complete all as specified and directed. 35 S&F 200 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified & directed. 36 S&F 150 mm in size aluminium handles cast type anodized complete all as specified & directed. 37 S & F 300 mm mild steel sliding bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and including a minium of 6 bolts and nuts four on bolt plate and two on stapple plate and fixed complete all as specified and directed by Engineer-in-Charge 38 M&L for preparing new surfaces of wood or wood based materials of any description not other wise described over 10 CM width or girth new or previously un treated wooden surfaces and applying one coat of pink primer and two coat of synthetic enamel paint complete all as specified & directed. 39 S&F mild steel framed work such as grills,gratings etc with ends of bars shouldered and / or riveted or forged into spiked, framed guard bars, iron doors, ladders, framed blasters, walkways, railings,framework of water tanks and similar work conforming to Fe 290 Grade E-165 complete all as specified and directed. 40 Preparation of new steel surfaces of any description over 10 cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 41 Excavating soft/loose soil in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and as directed. 42 M & L for cement concrete type C2 1:3:6 (40mm garde stone aggragate) as in foundations, filling and mass complete all as specified & as directed. 43 M & L for cement concrete type C1 1:3:6 (20mm garde stone aggragate) as in froof kerbs or mud stops, rounded or chamfered on edges complete all as specified & as directed. 44 S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed. 45 S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. 46 S&F Pre- painted galvatume aluminum zinc coating GI based Plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges,hips, valley gutters, drip fixed with self tapping screws complete all as specified and as directed. 47 M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as specified and as directed. 48 M&L for Rubber moulded chequered cement concrete tile with grey cement and pigment (of approved tint) of size 30 cm x 30 cm x 25 mm thick , set, jointed and pointed in neat cement slurry, complete all as specified and as directed. 49 M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment including laying over 20mm thick sand cushningwith complete all as specified and as directed. 50 S & FLow density polyethylene pipes (LDPE) 50 mmof pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and as directed. 51 Demolition of brick / stone / PCC block masonry / RCC Jalli fixed in cement mortar including all quoins, pillars, arches etc. all as specified and as directed. 52 Demolition of RCC of any descrition such as Kitchen chimniy, chajja, shelves, OHT Tanks,Pillar,wall, column,beam,slab etc and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge (reinforcement cut as required to facilitate demolition) 53 Demolition of cement Concrete of any description and in any position not otherwise specifically provided for complete all as spd and directed 54 Dismantling wrought iron or mild steelwork of any description not otherwise provided for 55 Dismantling of plain or corrugated steel sheeting any gauge, thickness, from roof coverings etc complete all as specified and directed. 56 Material & Labour for point wiring for one light / Fan point controlled by one, one way switch complete with 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable 1100 volts grade ISI marked drawn and including PVC capping & casing not less than 25 mm wide, including all accessories like bend, tees, junction boxes etc.including 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable as a earth wire connected to common earth dolly, etc including PVC surface type terminal box of suitable size with PVC cover complete all as specified and directed. 57 All as per item No 56 but One 3 pin socket out let 5 Amps on same board with other switches complete all as specified and directed. 58 M&L Switch Piano type, white polycarbonate body, single pole, one way 6 amp, 230 V, including connecting complete all as specified and directed. 59 S & F Switch socket combinationmultipurpose 5 pin 5 Amps, flush type, 230 / 250 Volts complete as specified and directed. 60 M&L for Ceiling roseceiling rose , 3 phase white polycarbonate body 6 Amps, 230 volts AC, including connecting complete. 61 S&F Distribution boardmade out of sheet metal enclosure (CRCA sheet) dust and vermin proof SPN 8 way with 200 Amps rated copper bus bar neutral bar, earth bar IP 43 protection, single pole and neutral 230 volts, double door type, fixed flush to wall complete all as specified and directed. 62 Supply and fix MCB’s single pole 6-32 Amps, 230 volts with ‘C’ curve, fixed in sheet metal board complete including connecting complete all as specified and directed. 63 Supply and fix MCB’s single pole & neutral, 40-63 Amps, 230 volts with ‘C’ curve, fixed in sheet metal board complete including connecting complete all as specified and directed. 64 S&F high intensity ,long range, weather & dust proof search light with PDC aluminum body, suitable for heat sinks,The search light would be supplied with 230 V 150 Watt LED COB lamp, range 400m,its electronic driver in cast aluminium housing with surge protection and 360 degree horizontal rotation CS mounted. The search light fitting would be suitable for installing on the roof the watch tower cabin with vertical rod with handle length 1.5 m from ceiling level arrangement sitable for both verticle 50 degreeand horozontal360 degree rotaion manual operational control from inside the cabin complete all as specified and directed.Make :- kalin, sigma or equivalent approved by GE. 65 Material & Labour for sub main wiring with 2 run single core multistranded copper conductor cable, of size4.0 Sqmm, PVC insulated, unsheathed, fire retardant, low smoke (FRLS) drawn through and including PVC conduit not less than 25 mm wide with all necessary fitting and including one run single core multistranded copper conductor cable, of size 4 Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire, fixed on wall / ceiling complete all as specified and directed.Note: 2 Runs of main cable and one run earth wire with Conduit will be measured as one RM for payment. 66 M&L for making hole by hammering or cutting on concrete ceiling/ CGI sheetfor fittement of Search light and again make it surface good finished with the help of cement concrete complete all as specified and directed. 67 Supply and fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one Double pole MCB of rating 20 amps complete all as specified and directed. 68 S&F of LED Street Light fitting 35 Watt, system efficiency not less than 100 lumen / watt, IP65/66 protection,consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws,fixed on existing bracket & connecting complete all as directed. 69 Supply and fix wall mounted fan 450 mm sweep high performance motor, with metal/plastic body ,jerk free oscillation aerodynamically designed & balanced blade incl grouting on wall with fastners & provision of 1.0 sqmm copper conductor of three core flexible cable from fan to connector/ceiling rose all as specified and directed. 70 S&F energy efficient LED tube light fitting integrated batten type with built in LED Chip & integral LED driver 20 watt, channel housing & diffuser of length 1200 mm (approx.) with all accessories, fixing arrangement internally pre-wired,fixed in position & connecting complete all as specified and directed. 71 Supply, laying, jointing, commissioning and testing cable LT XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor suitable for earth system of 10 sqmm 2 core cross sectional size ISI marked as per IS 7098 part I laid in trenches/ laid under floors/ laid under ducts or fixed on poles etc and connecting and testing etc, including dismantling & taking out old unserviceable cable complete all as specified and as directed.Note : (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.(ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.). 72 Material and labour for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts,complete all as specified and as directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment. 73 Supplying and laying ISI marked & conforming toIS- 5820- 1970 un-reinforced precast concrete cable cover, class LV, Type 1, flat, size 250 mm x 150mm x 40mm complete including dismantling & taking out old unserviceable cabe cover all as specified and as directed. 74 Material and labour of earthing complete with galvanised earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected tolead wire of size 4sqmm mm by means of bolts nuts check nuts and washer of galvanized steel, watering pipe of 20 mm bore, galvanised iron, light grade, and 40 mm bore galvanised iron light grade for earth wire protectionincluding all excavation earth work in any type of soil, PCC pit in PCC 1:2:4 type B-1 and RCC 1:2:4, type B1 for precast chamber cover 50 mm thick, reinforced with welded steel wire fabric or XPM Jali (weight not less than 4.00 Kg / sqm),with charcoal, salt, funnel complete all as shown in the electrical plate No 3 of SSR part –I and testing on completion.Note:-Quoted rates shall be deem to include for earth strip with protection pipe up to 7.5 M length. 75 Supply and lay GI tubing light grade 40 mm bore with all necessary fittings laid in trenches, under roadcrossing, in floors/wall or fixed to poles / DB for cable protection etc complete all as specified and directed.
|