Construction Of Sub Center Sangri Baramulla= 1 Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.All kinds of soil,incld. cutting of trees,removal of tree stumps and dewatering of trenches during execution of work.. 2 Earth work in excavation in all kinds of soilby Manual/mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspitsand the like not exceeding 10 sqm on plan, including dressing of sides andrammingofbottomsliftupto1.5m,includinggettingoutexcavatedearthand disposal of surplus excavated earth as directed by site Engineer incld.cutting of trees, removal of tree stumps and dewatering of trenches during execution of work.. 3 Supply and filling of dry stone soling in foundation trenches/under floors tightlyhandpacked with hand ramming, dressing ,watering incld. carriage of material from source to site of workcomplete 4 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m 5 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering. All work up to plinth level 1:4:8 (1 Cement: 4 coarse sand: 8 grade stone aggregate 40mm nominal size) including all carriages. 6 Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete, including all carriages. 7 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering. All work up to plinth level 1:2:4 (1Cement: 2 coarse sand: 4 grade stone aggregate 20mm nominal size)including all carriages. 8 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including all carriages 9 Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)including all carriages. 10 Centering and shuttering including strutting propping etc. and removal of form forfoundation, footings basses of columns etc .For mass concrete including all carriages. 11 Centering and shuttering including strutting, propping etc. and removal of formfor suspended floors, roofs, landings, balconies and access platforms.including all carriages. 12 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all levels, Thermo-Mechanically Treated bars of grade Fe-500D or more, including all carriages. 13 Providing wood work in frames of doors, windows, clesrestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately)First class imported KD wood including all carriages 14 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, including p/f of panelling of prelaminate Board for doors and 4mm glass panes for windiow panes including all almunium fittings and fixtures all complete as per direction of Engineer-in-charge including cost of priming coat and two or more coats of synthetic enamel complete job (Ist Class Imported KD wood) with cost of required number of Hold Fasts complete 15 Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge uding cost of priming coat and two or more coats of synthetic enamel complete job:(Ist Class Kail Wood) 16 P/F of 4 mm thick glass pane (weighing not less than 10 kg/sqm) 17 Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand ) including all carriages. 18 Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand ) including all carriages. 19 12mm Cement plaster of mix in 1 : 4 ( 1 cement : 4 coarse sand)including allcarriages. 20 6mm cement plaster to ceiling of mix 1 : 3 (1 cement: 3coarse sand) including all carriages. 21 Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surfaceeven and smooth complete including all carriages 22 Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm),including all carriages. 23 Providing hoisting and fixing trusses/purlins/ rafters/posts/post- plates, false ceiling , Partitions etc. Sawn and fixed in poisition or like components including cost of screws etc. complete First class Poplar wood including allcarriages. 24 Providing & fixing of 0.40 mm colour coated GI sheets for soffits with frame work of 2x2 size placed @600 mm center to center both ways with imported KD/Budloo wood as per the design as directed including cost of nails , screws , scaffolding etcincluding all cost & carriage of materials complete job. 25 Providing & fixing of 0.50 mm colour coated GI Sheet ornamental eves boarding 300 mm wide as per the design as directed including cost ofnails , screws , scaffolding,welding etcincluding all cost & carriage of materials complete job. 26 Providing & fixing colour coated (Hi-Rib) G.I sheet roofing 0.50mm thick incl. vertical/curved surface fixed with polymer coated J or L hooks bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I limpet washer and over lapping of sheets complete in horizontal vertical trusses incl. cutting to size and shape wherever required including Ridges or Hips of60 cm overall width colour coated sheets0.50mm thick andvalleys of 90 cm width colour coated sheets0.50mm thicketc complete as per the directions of Incharge Engineer. including all carriages. 27 Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 28 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand)including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm 29 Providing and laying gang saw cut of specified thickness, mirror polished pre- moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. 18 mm thick 30 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete including all carriages 31 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.In colour such as White, Ivory, Grey, Fume Red Brown, including allcarriages. 32 Dry random rubble masonry with hard stone in foundation and plinth With bond stone 33 Construction brick massionary manhole with 7.5 class designation bricks in cement mortar 1:4 (1 cement; 4 fine sand ) CI cover with frame , foundation concrete 1:3:6 (1cement : 3 fine sand :6 graded stone aggregrate 20 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand ) finished smooth with a floating coat of neat cement on walls and bed concrete etc complete as per standard design: as per the directions of site engineer incld all cost and carriage Inside dimensions 450x450 x600 mm deep 34 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests including all carriages 35 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid including all carriages 36 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls whereverrequired:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer 37 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040mm bowl depth 250mm 38 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. PN-16 pipe , 32mm OD(SDR-7.4) 39 PN-16 pipe , 25mm OD(SDR-7.4) 40 PN-16 pipe , 20mm OD(SDR-7.4) 41 PN-16 pipe, 16mm OD(SDR-7.4) 42 Providing and Fixing of PVC pipes with fittings like P-bend,D-bend,P/F-Trap, collar, junction, Door Tee,Reducer etc (B-Type) of approved brand and manufacture (Prince/ Supreme or Equivalent brand) incld all carriages 100 mm dia 43 Providing and Fixing of PVC pipes with fittings like P-bend,D-bend,P/F-Trap, collar, junction, Door Tee,Reducer etc (B-Type) of approved brand and manufacture (Prince/ Supreme or Equivalent brand) incld all carriages 75 mm dia 44 Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 of approved quality & make (Jaguar/ Hindware) 45 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.(a) 15 mm nominal dia each 6805.80 18.23 Providing and fixing white 46 Providing and fixing of water heating geysers of approved brand & quality (Venus/ Jaguar/ Racold or eqviuallent) with all necessary fittingsand fixtures complete Job. 50 Ltr capacity including all costs and cariages complete 47 Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 of approved quality & make (Jaguar/ Hindware) 48 Providing and placing on terrrace (at all floor levels) polyethene water storage tank ISI:12701 marked triple layer indicating the BIS License No with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fittings and base support for tank (Sintex, Electroplat, Star, Lotus or equivalent having valid ISI license) including all carriages. 49 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two or more coats of synrhetic enemal paint using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, grills,brackets, gates and similar works, including all carriages. 50 Providingand commisioninglighting pointsincld wiring for lighting points in 1.5 Sq.mm PVC insulated copper wire and 2.5 Sqmm PVC insulatedmulti-strand copper wire for lightingsub mains,6 amp 1 way switch,2 mm thick PVC conduit/Channel with bends,junction boxes etc ,6 amp S Pole MCB ,10 amp DP MCB,2 way DB for housing MCB and hylem sheet of ISI mark and approved make with wooden box recessed in wallls with acessoriesincld all carriages(concelead type 12 watt) 51 Providing and commissioning heating point incld wiring for heating points in 2 .5 sq.mm PVC insulated multi-strand copper wire and 4 sq.mm PVC insulated multi-strand copper wire for heating sub-mains,16 AMP switch socket combine,,2 mm thick PVC conduit/Channel with bends, Junction boxesetc , 10 Amp S pole MCB ,2 way DB for housing MCB and hylem sheet of ISI mark and approved make with wooden box recessed in /over wallls with acessories complete incld all carriages 52 Providing and commissioning of fan point incld wiring for lighting points in 1.5 sqmm PVC insulatedmulti strand copper wire,1200 mm ceiling fan /225 mm exhaust fan with ceiling roses andPVC square block ,350 watt electronic fan dimmer, 2 mm thick PVC conduit/Channel with bends, Junction boxesetc, 6 mm S pole MCB ,10 amp DP MCB , 2 way DB for housing MCB for lighting circuits and hylam sheet of ISI mark and approved make with wooden boxrecessed in wallls with acessories complete incld all carriage and costs of Fan and all other material involved. 53 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer, including allcarriages. 54 Providing and fixing of 18 deep Ward Robes/ Almirah of required size and pattern with 19mm thick Water proof Ply Board fitted with Dalmica including frame Work & fixing of ornamental hinges, Handles, Catchers, adhesive, cornice , beeding & necessary locking arrangements as per the directions of site engineer with all leads,lifts, costs & carriages of all materials involvedupto site of work complete job 55 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete 56 Providing and fixing three seater Glossy Stainless Steel Reception Waiting Chair For Hotel And Hospital.width 78cm,181cm,68cm approx,120kg per seat,cushioning foam. Including carriage 57 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).including allcarriages. 58 Providing and fixing of 6 mm thick plywood(kit ply,Greenply,Century,Sarda,Mayur or equivalent) in ceiling/ partition of walls or equivalent workwith cost of Nails, cornice, etc all inclusive including cost and carriage of all material involved complete. with cost of 2mm waterproof putty, cement primer and two or more coats of syntheitic enamel with foam/Lime infill with cost of 2x2 frame work of imported wood 59 Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge incld.glazing of float glass panes 5mm thick for windows,ventilators etc and Aluminium sheets(ACP)as per size required for panelling of doors/partitions and dashfasteners,Powder coated aluminum (minimum thickness of powder coated 50 microns) all complete frame work,shutters ,float glass,ACP etc complete jobincluding all carriages. 60 Providing & fixing of 12 mm thick imported wooden panelling over 12mm thick plyboard (kit ply, Greenply, Century,Sarda,Mayur or equivalent) including cost of ply board, cornice 75 mm wide,beading polishing two or more coats of malamine / MDF polish , cornice, nails etc and carriages all inclusive complete job. as per the directions of incharge engineer at site 61 Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.
