Tender For Provn Of Equipment Room For Certain Op Equipement At Af Stn Leh; 1 M&L for surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting outcomplete in hard/dense soil complete all as specified and as directed by Engr-in-Charge. 2 Excavating in post holes (or similar holes) in Hard/Dense soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed by Engr-in-Charge. 3 Excavating in trenches n.exc 1.5 m wide and n exc 1.5 m in depth, for foundation, etc or for shafts, wells, cesspits, manholes, pier holes. Etc n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in any type of soil, complete all as speified and directed. 4 M & L for cement concrete 1:2:4using 20mm graded stone aggregate as post holes and inlintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided nfor in Item 04028, water ntroughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. 5 M&L for cement concrete 1:3:6 type C2 using 20mm graded stone aggregate as in plinth protection joint filled with bitumen sand mixer, 50mm thick finished even and smooth without using extra cement complete all as specified and as directed. 6 M&L for cement concrete Type D–2, 1:4:8 (40 mm graded crushed stone aggregate) in foundations, filling and mass–concrete all as specified and as directed. 7 M&L for Pre–cast cement concrete block masonry with solid blocks of Type C–1, 1:3:6 (20 mm graded crushed stone aggregate) exc. 10 cm in width and setting in mortar 1:4, complete all as specified and directed. 8 M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finish smooth & even without using extra, complete all as specified and directed. 9 M&L for Preparation ofnew plastered surfaces of walls and applying two coats of cement base paint over a coat of primer on wallscomplete all as specified and as directed by Engineer-in-Charge. 10 M&L for preparation of new steel surafcesand applying two coats of synthetic enamel paint over in camouflaging pattern , complete all as specified and directed by Engineer-in-Charge. Notes:(i) Camouflaging pattern will be approved by the GE. 11 Returning, filling in Any type of soil, incl spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as speified and directed by Engineer-in Charge 12 Removing excavated material (soil) exc 1.50 km and depositing where directed at a level n exc 5.00 km above the starting point, complete all as speified and directed. 13 M&L for Hardcore of broken stone or boulders gauge n exc. 63 mm, deposited, spead and levelled in layers n exc 15 cm thick, watered and rammed to true surface, complete all as specified and directed by Engr-in-charge. 14 M&L for 75mm thick cement concrete 1:2:4, type B-2, (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and directed. 15 M&L for 40mm thick cement concrete type B–0,1:2:4,(using 12.5 mm graded crushed stone aggregate) as in Sub-Floors, sub bases, Floors and finishing cement concrete surface fair and even, complete all as specified and directed. 16 M & L for Vitrified ceramic Light shade tiles 8 to 10mm thick (square /rectangular) area of each tiles exceeding 0.18 Sqm but n exc 0.38 sqm in floors etc. over 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tilescomplete all as specified and directed. 17 M & L for non skid ceramic coloured tiles 7 to 8mm thick (square /rectangular) area of each tiles exceeding 0.06 Sqm but n exc 0.11 sqm in floors etc. over 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tilescomplete all as specified and directed. 18 M& L Glazed ceramic coloured tiles in vertical surface area exc 0.06 Sqm but n exc 0.15 Sqm of 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and includingRendering 10mm thick Cement plaster 1:4 on fair faces of brick work or concrete surfaces,complete all as specified and as directed by Engineer-in-Charge. 19 S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 etc, complete all as specified and as directed. 20 S&F for rolled mild steel sections as in column main and joist, channel, angle, or tee sections, fixed independently etc. (cut to ordinary lengths i.e. within 20mm of the length indicated, fixed with angle cleats or other connecting plates of Fe 410-W (Gde E-250) quality A complete all as specified and as directed by Engineer-in-Charge. 21 M&L for preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed by Engr-in-charge. 22 S&F Plates (plain or chequered) channels,squarecutor notched (ordinaryand counter sunk) forming holes, with riveted, bolted or welded attachment, complete all as specified and directed. 23 S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,, n exc 5cmlong where diameter of neck is 5 to 10mm as required, complete all as specified and directed. 24 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. 25 S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed. 26 S&F 60mm thick PUF panels in wall with 0.5mm prepainted galvalume sheet on both face/side including all fixing arrangements, complete all as per specification and as directed. 27 S&F 40mm thick PUF false ceiling panels with 0.5mm prepainted galvalume sheet on both face/side including all fixing arrangements, complete all as per specification and as directed. 28 M&L for door shutters with 60mm thick PUF panel with 0.5mm thick prepainted MS sheet on both side (Colour as approved by GE) including aluminium 200mm tower bolt (2 Nos), aluminium sliding bolt 300mm (01 Nos), built in locking arrangement (sliding door bolt) and handle 02 nos on both faces including chowkhat of angle 60 x 60 x 6mm fixed with 03 Nos (100mm) heavy duty hinges complete all as specified and directed by Engr-in-Charge. 29 S&FAnodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.),complete all as specified and as directed by Engr-in-Charge 30 S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, sliding bolt 2 Nos, hinges, anodised aluminum snap beading screws etc. complete all as specified 31 S&F Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc,complete all as specified and as directed by Engr-in-Charge 32 S&F Anodised aluminium work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom andsideswithrequired EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge 33 S&F sheet glass of 5.0 mm thick oridinary quality and glazing with rubber packing to sliding windows in square not exceeding 0.50 sqm in each pane, complete all as specified and as directed by Engr-in-Charge 34 S&F frosted type sheet glass of5.0 mm thick oridinary quality and glazing with rubber packing to sliding windows in square not exceeding 0.50 sqm in each pane, complete all as specified and as directed by Engr-in-Charge 35 S&F for sheet glass 5.0 mm thick oridinary quality and glazing with rubber packing to sliding windows in square exceeding 0.50 sqm in each pane, complete all as specified and as directed by Engr-in-Charge 36 S&F for aluminium (die cast body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. 37 S&F Vitreous China Urinal, half stall type, white including all fittings complete all as specified and directed by Engr-in-charge. 38 S&F Vitreous China wash down water closet pan (pedestal pattern) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, including 10 ltr PVC flushing cistern and plastic seat cover and other required CI fitting etc, complete all as specified and as directed by Engr-in-Charge.Note: Qty and Rates are inclusive of CI P and S trap. 39 S&F PVC connections 15mm size with PTMT nuts of length 600mm,complete all as specified and as directed by Engr-in-Charge 40 S&F Angle/Stop valves, 15 mm bore fancy type chromium plated cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed,complete all as specified and as directed by Engr-in-Charge 41 S&F Bib taps long body,15 mm bore fancy type cast copper alloy Chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed,complete all as specified and as directed. 42 S&F Fancy type Premium qualityChromium platedToilet paper holder with flat recessed type stainless steelcomplete all as specified and as directed. Note :- Design as approved by GE 43 S&F Health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including making connection and fixed in position, complete all as specified and as directed by Engr-in-Charge. Note :- Design as approved by GE 44 S&F Vitreous China wash basin, white, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe with and including 32 mm Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including all CI fittings wherever required,complete all as specified and as directed. 45 S&F Pillar taps, 15 mm bore cast copper alloy, with capstan heads,chromium plated ,screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed,complete all as specified and as directed. 46 M&L 3-layer PP-R Polypropylene random copolymer) concealed pipes Outer diameter of pipes 25 mm SDR 7.4 (PN16) UVstabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings and outlet fittings to tanks fixed complete to walls, ceilings or in floors etc, complete all as specified and as directed by Engr-in-Charge. 47 M&L 3-layer PP-R Polypropylene random copolymer) concealed pipes Outer diameter of pipes 20 mm SDR 7.4 (PN16) UVstabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings and inlet fittings to tanks fixed complete to walls, ceilings or in floors etc, complete all as specified and as directed by Engr-in-Charge. 48 S & F PP-R gate valves 25 mm outer dia of pipe (brass insert) as per site requirement, complete all as specified and as directed by Engr-in-Charge. 49 S&F bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup waste washer complete all as specified and as directed by engineer in charge. 50 Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed, complete all as specified and as directed. 51 S&F fancy type Premium quality Chromium plated Soap Dish Square or Rectangula, complete all as specified and as directed.Note :- Design as approved by GE 52 S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed by Engr-in-Charge. 53 S&F 100mm diaCast iron soil, waste and vent pipesin any length with or without ears, with cementjoints, fixed to walls and clamp at 1m interva etc including all CI fitting wherever required, complete all as specified and as directed. 54 S&F 100mm diaCast iron soil, waste and vent pipesin any length with or without ears, with cementjoints, in floors etc including all CI fittings wherever required, complete all as specified and as directed. 55 S&F 75mm diaCast iron soil, waste and vent pipesin any length with or without ears, with cementjoints, laid in trenchesor in floorsincluding all CI fittings wherever required, complete all as specified and as directed by Engr-in-Charge 56 S&F 75mm diaCast iron soil, waste and vent pipesin any length with or without ears, with cementjoints, fixed to walls and clamp at 1m interval etc includingall CI fittings wherever required, complete all as specified and as directed by Engr-in-charge 57 S&F 75mm CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and as directed by Engr-in-Charge 58 S&F 100mm dia CI cowl as in vent pipe, compele all as specified and as directed by Engr-in-charge. 59 S&F 75mm dia CI cowl as in vent pipe, compele all as specified and as directed by Engr-in-charge. 60 M&L 100mm thick cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) as in sub base, complete all as specifioed and directed by Engr-in-Charg 61 M&L for sand filling under floor or in cushion under interlocking tiles etc, complete all as specifioed and directed by Engr-in-Charge. 62 S&F Machine pressed precast cement concrete coloured interlocking paver block of any shape and size confirming to IS-15658-2006 of 100mm thick with gray cement and pigment (M-35 Grade), complete all as specifioed and directed by Engr-in-Charge. 63 S&F forRooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe - 410 W (Gde-E-250) quality A, complete all as specifioed and directed. 64 Excavating in trenches exceeding 1.5 mtr butnot .exceeding3.0 mtr wide and n exc 1.5 m in depth, for foundation, etc or for shafts, wells, cesspits, manholes, pier holes. etc n exc 10 sqm on plan and getting out in any type of soil, complete all as speified and directed. 65 Excavating in trenches not exceeding 1.5 mtr wide and n exc 1.5 m in depth, for laying GI pipe etc and getting out in hard/dence soil, complete all as speified and directed. 66 M&L for Pre–cast cement concrete block masonry with solid blocks of Type C–1, 1:3:6 (20 mm graded crushed stone aggregate), exc. 10 cm in width and setting in mortar 1:6, complete all as specified and directed. 67 M&L for RCC (Nominal Mix) Type B–1, 1:2:4 (20 mm graded crushed stone aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, Manhole coversand in shelves and the like complete all as specified and directed. 68 M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200m thick (Horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed. 69 M&L for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 70 M&L for 150 mm bore RCC NP-3 soil waste pipe laid in trenches and jointed all as specified. 71 M&L PCC 1:3:6 type C–2 (20 mm graded crushed stone aggregate) as in concrete bed to 150 mm bore drain pipe incl packing under haunching against the sides of pipes after pipe laid and tested complete. 72 S&F Sheet metal enclosure double door for DBs SPN 8 way 240 V having200 A rated bus bar complete all as specified and directed by Engr-Incharge. 73 S&F Sheet metal enclosure double door for DBs SPN 4 way 240 V having200 A rated bus bar complete all as specified and directed by Engr-Incharge. 74 S&F Sheet metal enclosure double door for DBs TPN 4 way 415 Volt having 200 A rated bus bar complete all as specified and directed by Engr-in-charge. 75 S&F MCB 63 Amp TPN415 volts 50 Hz 25 KA, complete with allaccessories as required on site & as directed by engineer-in-charge. 76 S&F MCB SPN 40A, 240 V -10 KA, C type, ISI Marked all as specified and as directed by Engineer-in-charge. 77 S&F MCB SP 6-32A, 240 V -10 KA, C type, ISI Marked all as specified and as directed by Engineer-in-charge. 78 M&L for point wiring for one light/Fan/bell point controlled by one switch one way in & including PVC or casing and capping including accessories, ISI marked as per site requirement using FRLS PVC unsheathed multistrand copper conductor unsheathed cable 1.5 sqmm single core for one light/fan point/bell point controlled by one switch including 3 mm thick plastic laminated sheet cover over PVC Box for earth continuity insulated PVC unsheathed(green colour) 1.5 sqmm copper earth wire connected to common earth dolly using complete all as specified and directed by Engr-in-charge.Note : (a) wiring shall be done by using proper colour coding. 79 All as per srl item No. 78 here-in-before but for 05 Ampsocket outlet on independent board 80 All as per srl item No. 78 here-in-before but for 05 Ampsocket outlet on same board 81 All as per srl item No. 78 here-in-before but for 15 Ampindependent socket outlet using 4 sqmm single core copper wure wire for phase, neutral & earth complete all as specified. 82 S&F Switch piano, flush type 5 AmpsISI marked One Way 230 volts complete all as specified. 83 S&F Socket outlet2-in-1 3 pin 6 & 16 ISI marked Ampsflush type 230 volts complete all as specified. 84 S&F Socket outlet2-in-1 3 pin 6 Amps ISI marked flush type 230 volts complete all as specified. 85 S&F Switchone way 15 AmpsISI markedflush type 230 volts complete all as specified. 86 S&F Ceiling rose 3 terminal size 50x65mmISI marked surface type 230 volts complete all as specified. 87 S&F Holder insulated body with back plate including 9 wattLED lamp, complete all as specified and directed by Engineer-in-Charge. 88 S&F LED light fitting 1 x 20 watt, 220 V, AC decorative box type with driver ISI Marked , holde including LED tube rod connecting up with three core flexible copper wire of suitable size from ceiling rose complete all as specified and as directed.Make : CAT Part No BCLAB/BCLSB 20W of Bajaj or Equivalent of Havells, Philips, Crompton 89 S&F Energy saving new generation Endura Rugby Neo - IP65, 10WLED IP65 bulkhead luminaire with opal diffuser, etc complete with all accessories rewired electrically connected all as specified and directed by Engr-Incharge. 90 S&F Exhaust Fan plastic body, 250mm(12) sweep, single phase, 230 volts 50 Hz AC,1400 RPM, energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminiun rotor mounted on two ball bearings complete with louvers and shutters including cutting hole for fixing exhaust fan to Puf Pannel , connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable over all sheathed all as required at site and as directed.Make: Havells/Bajaj/Crompton/orient 91 S&F Wall Fan of size,400 mm sweep, single phase, 230 volts 50 Hz AC,1400 RPM, energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminiun rotor mounted on two ball bearings complete with louvers and shutters including cutting hole for fixingto wall and making good the disturbed surfaces (including plastering, necessary brickwork and distempering) to match with the existing specification, connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable over all sheathed all as required at site and as directed.Make: Havells/Bajaj/Crompton/orient 92 M&L for Sub main wiring complete with FRLS PVC insulated unsheathed stranded copper conductor wire 6 Sq mm 02 Nos. (for Phase & Neutal)alongwith earth wire FRLS PVCISI marked insulated unsheathed stranded copper conductor wire of size 6 sqmm wire drawn through in & including PVC casing capingISI Marked complete all as directed by Engr-In-charge. Note : (i) Two single core cable and one run of earth copper cable will be measured and paid as one unit length 93 Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground (Earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected and including GI wire 4 mm dia (upto the body of equipment) by means of brazing, GI bolts, nuts, check nuts and washers, earthplates surrounded by packed layers of coal dust and common salt 15 cm thick all around top and bottom and watering pipe 20 mm bore of GI pipe, light grade all as shown in Electrical plate No 5 of SSR Part I, testing on completion including PCC1:2:4 tye B1 using 20mm graded stone aggregate as in pit cover and PCC chamber in PCC 1:3:6 type C-1 using 20mm graded stone aggregate including excavation and earth work, disposal of surplus spoil to a distance n exc 50 m complete all as specified and directed by Engineer-in-Charge 94 M&L for maintenance free chemical earthing system complete with UL464 approved copper bounded earth rod 17mm dia 3mm dia 3 mtrs long electrode buried in ground to bore holes 150mm dia.Vertically to a depth not less than 0.50 mtr below normal ground level including Provision to connect the earth continuity conductor with copper bounded earth rod as per manufacture design or all as directed including 6 kg NABLLAB certified back fill chemical compound for filling bore bole with min 6 kg of Hygroscopic Gel.The ground enhancement chemical my be used in place of back fill compound asrequired and chemical may be used in place of back fill compound as required and manufacture recommendation to obtain below 1.0 ohms earth resistance value.A layer of 250-300mm soil (vegitable/cotton soil) is also required outside earth bore including necessary ingradients and water during process botain desired value.The earthing strip of size copper 20x3mm up to length of 7.5 mtr up to test point from copper rod is also included test point terminal block should be made of Gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos 8mm long hexagonal head screw complete.The scope indlude iron frame of size 20x20mm fixed with hinged with Pit cover of 300mmx300mm made of cast Iron as per company standard shall be as recommended buy manufacture complete all as specified.Make-JMV/Pargati electrocom/EnoveNote :(i)Payment shall be made only after satisfactory testing to the entire satisfaction of GE.The contractor has to make alternate earthing in case test result not found satisfactory without any extra cost and rate should include the cost of that provision of earthing. (ii)Contractor shall submit 1 years guarantee for earth resistance below 1 ohms and earth neutral voltages less than 1 volts. 95 Material and labour for aluminium strip of 25x3.15 complete with saddles mmwith screws/ washers etc.over Elapp epoxy electrical insulator (red)on wall and roof of building complete all as specified and as directed.Note: Aluminium strip should not touch building or roof at any place 96 Material labour and labour air termination, single pointed aluminium rod 12mm dia and 300mm long and Elapp epoxy electrical insulator (red)screwed properly on aluminium strip complete all as specified and directed by Engr-in-Charge.. 97 Material and labour for test point terminal block made out of gun metal or phosphorus bronze size 75 x 75 x 25mm drilled and screwed including 3 Nos 8mm dia 25 mm long hax. head screw complete all as specified and as directed by Engr-in-Charge. 98 Sapply and laying GI water tubing, 80 mm dia, light grade (ISI marked) with all fittings (such as bends,elbows,TEE,short pieces, connectors back nut,disminishing pieces, capes and plug,union etc) complete all as specified and as directed 99 Supply and lay GI water tubing, 20mm dia, medium grade (ISI marked) with all fitting (such as bends, elbows, TEE, short pieces, connectorsback nut, disminishing pieces, caps and plug, unions etc) all as specified. 100 Supply and lay GI water tubing, 25mm dia, medium grade (ISI marked) with all fitting (such as bends, elbows, TEE, short pieces, connectorsback nut, disminishing pieces, caps and plug, unions etc) all as specified. 101 M&L for cement concrete cast in siti 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) for pole foundation & coping /panel/foundation /chain link fencing, thetop surface shall be smooth by using extra cement slurry including usage and wastage of form work all as specified and directed. 102 Supply of the 1 Kg capacity of fire extinguisher dry powder type A,B,C conforming to IS 13849 alongwith its accessories complete all as specified and as directed 103 Supply, installing, testing and commissioning of energy efficient 5 star rated as per BEE air cooled, split unit Air Conditioner, all weather with heating and cooling , electric driven, with cordless remote control unit, single phase of capacity 1.5 Ton, including cutting holes for connections between indoor and outdoor unit with copper tubing, stand etc, and testing for leakage, suitable for CFC/HCFC refrigerent complete all as directed. 104 Supply, installing , testing and commissioning of Voltage Stabiliser copper wound for automatic operation , single phase, 50 c/sAC Supply naturally air cooled indoor type, wall mounted & designed for input variation between 170 V to 250 V with output voltage stabilised at 230 V with accuracy of ± 2.5% and of capacity 5 KVA etc, complete all as specified and directed. 105 S&F Single Pole and Neutral enclosure with two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified anddirected. 106 Supply and fix of stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 25 mm dia bire all as specified. 107 Supply and fix of stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 20 mm dia bire all as specified. 108 M &L for Random rubble uncrushed stone masonry in cement mortar 1:6 valve pit of internal size (150cm x 150cm x 150 cm), with 38 Cm wall thickness, 50mm thick coping with PCC 1:2:4 type B-1 (using 20mm graded stone aggregate), plastering internally with 15mm thick in Cement mortar 1:6 and flush pointingexternally in the same mortar as the work proceeds including excavation and including anglee iron frame made of 50x50x5 mm angle iron with MS sheet cover of size 3.15 mm thick of size with provision of locking arrangement including earth work and disposal of surplus soil to a distance not exc 50 mtr and depositing all as directed. 109 M& L for cutting of pipe upto 80mm dia for insertion of new pipe complete with welding, brazing complete all as specified and directed.
