|
Tender For Repair And Maintenance Work Of Pratappura Residential Colony Agra - Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.. (As per DSR 13.91) 2 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.(As per DSR 15.56) 3 Class-150 (Non Modular) brick work in 1:4 cement and Coarse sandmortar in foundation andfor super structure above plinth level upto floor five levelincluding necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than12cm. including supply of all materials, labour and T&P etc. required for proper completion of the work DSR NO- 6.1.1+6.13.2 (7370.65+1123.80) 4 Finishing walls with Acrylic Smooth exterior paint of required shade :(Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)supply of all labour material and T&P required for proper completion of work. Ch- 15 SI No- 5 5 12 mm thick plaster with cement and coarse sand in 1:4 ratio over brick works including supply of all material, labour & T&P etc. complete. (As perDSR no- 13.4.1) 6 15mm Cement plaster with cement mortar in proportion of 1:4 cement & coarse sand ofsingle coat for exterior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm. In girth and finished even and smooth. DSR- 13.5.1 7 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm. (as per DSR 11.41.2) 8 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.(as per DSR 13.80) 9 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. (as per DSR 9.20.2) 10 Finishing walls with water proofing cement paint of required shade :Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat D.S.R. 13.109.1 11 Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.(As per DSR 10.31) 12 Providing and Fixing glass panes with putty and glazing clips in steel doors, window , clerestory window , all complete with 4.00 mm thick glass panes. D.S.R. 10.30.1 13 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give and even shade. One or more coats on old work including prepration of old surface.Old work DSR-13.99.1 14 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 2nd class teak wood beading 62X19 mm (as per DSR 9.51.1) 15 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25mm nominal dia Pipes DSR (18.7.3) 15 mm nominal dia Pipes 16 20 mm nominal dia Pipes 17 25 mm nominaldia Pipes 18 Providing and placing on terrace (at all floor levels) Polyethylene water storage tank ISI:12701 marked (Sintex or equivalent) with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and the base support for tank complete as per direction of Engineer in charge. (DSR- 18.48) 19 Providing and fixing C.P brass stop cock 15mm nominal bore for basin mixer and geyser points of approved quality confirming to IS:8931.(DSR- 18.52.1) 20 Providing and fixing C.P brass 15 mm nominal bore bib cock of approved quality confirming to ISI standards and weighing not less than 690 gms.(DSR- 18.49.1) 21 Providing and fixing C.P brass angle valve 15mm nominal bore for basin mixer and geyser points of approved quality confirming to IS:8931.(DSR- 18.53.1) 22 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 12.41.2 110 mm diameter. (as per DSR 12.41.2) 23 Note - 1- Rates are inclusive of all taxes but excluding GST which shall be paid extra as applicable2- Labour cess @ 1% will be deducted from contractors bill at the time of payment
|