|
Tender For Remaining Work Of Police Station Building At Itawa In District Kota - Earth work in excavation over areas ( exceeding 30 cm in depth, 1.5 Mtr. In width as well as 10 sqm on plan) including disposal of excavated earth lead up to 50 m and lift up to 1.5 mtr disposed earth to be leveled and neatly dressed including stacking of useful material if available. 3 b) Hard rock (blasting prohibited) useful material 30% 4 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering -ALL work up to plinth level 1:4:8(1 cement :4 coarse sand : 8 grade stone aggregate 40mm nominal size ) 5 Random Rubble stone masonry for with hard stone in foundation and olinth in cement sand mortar 1:6 (1 Cement 6 Sand above 30cm thick wall. 6 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centering, shuttering and reinforcement including curing, compaction, finishing with rendering in cement sand mortar 1 : 3 (1 cement : 3 coarse sand) and making good the joints and Admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete improve workability without impairing strength and durability as per direction of Engineer-in-charge. M-20 grade reinforced cement concrete. All wiork up to plinth level. 7 Centering & shuttering with plywood or steel sheets including strutting, propping, bracing bothways with wooden members and removal of formwork forSuspended floors, roofs landing starcases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills,chajjas,lintel,beam etc. 8 Centering & shuttering with plywood or steel sheets including strutting, propping, bracing bothways with wooden members and removal of formwork forColumns, Pillers, posts and struts etc 9 Flyash Brick masonry in super structure upto third storey with Flyash Bricks of class designation 75 in Cement mortar 1 : 6 (1 cement : 6 coarse sand). 10 Half Flyash Brick masonry in super structure upto third storey with Flyash Bricks of class designation 75 in Cement mortar 1 : 6 (1 cement : 6 coarse sand). 11 Add extra item No. 13 for using nominal hoop reinforcement at requisite interval. 12 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centering, shuttering and reinforcement including curing, compaction finishing with rendering in cement sand mortar 1 : 3 (1 cement : 3 coarse sand) and making good the joints and admixtures in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete improve workability without impairing strength and durability as per direction of engineer-in-charge. M-20 grade reinforced cement concrete. All work from plinth level up to floor three level. 13 Beams, plinth beams, girders, bressumers, cantilevers, suspended floors, lintels, roofs and staircases including spiral staircase, shelves etc. 14 Walls, columns, pillars, posts and struts. 15 Providing M-25 grade R.C.C. instead of M-20 grade R.C.C. 16 Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level.Thermo-mechanically Treated bars (Tata, SAIL) 17 Grading roof water proofing treatment with Cement concrete 1:2:4 (1-Cement: 2-coarse sand : 4-graded stone aggreate 20mm nominal size). 18 Making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1 : 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1 : 3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. 19 Crazy marble stone flooring 20mm thick marble stone with black or of specified colour topping including filling the gaps with cement marble chips mixin proportion of 4 : 7 (4cement: 7 white black or white or black marble chips) size from 1mm to 4mm by volume and under layer of 25mm thick cement concrete [1:2:4, graded stone aggregate 12.5mm nominal size] rubbing and polishing and cement slurry etc. complete : White cement without pigment.In ordinary cement. 20 Providing and fixing 20 mm thick terrazo tile over roofing fixed in cement mortar 1 : 4. 21 Providing and fixing stone slabs table rubbed, 18-20 mm thick in Walls, Steps, Pillars, Counters, Jambs, Shelves, Sills etc. laid on 12 mm (Av.) thick base of CM 1 : 3 (1 cement : 3 coarse sand) jointing with white cement mortar 1 : 2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab complete including grinding, rubbing and polishing.Rajnagar 1st quality with light spots.1501 Cm2to 3600Cm2 Tiles 22 Providing batta (gola) 75mm*75mm in cement concrete(1:2:4) includingfinished with cement mortar 1:3 as per standard design 23 Supplying and fixing rough dressed stone sills, dasa, coping, cornices sriwan, string courses etc. in cement mortar 1 : 4 including pointing with admixture of pigment matching with the stone shade :50mm 24 Supplying and fixing in walls machine cut and polished stone shelves, tands andin CM 1:3 with machine cut edges :(a) Sand or other approved stone 50mm thick. 25 (b) (b) Kota stone 25 to 30mm thick. 26 Providing and fixing Granite stone slab mirror plished and machine edge cut in Wall, Pillars, Steps, Shelves, Sills, Counters. Floors etc.Laid on 12mm (Av.) thick base of cement mortar 1:3 jointing with white cement mortar 1:2 (1 white cement : 2 marble dust ) with pigment to match the shade of the marble slab complete including grinding,rubbing and polishing of : Green /Black/Other granite Size above 3601 Cm2 27 Extra for providing edge moulding to 18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite Work 28 Carriage of earth, sand,lime,morrum,mannure or salb etc. including loading, unloading & staking as per specification etc. complete with lead of 10 Km. 29 Providing and fixing 1st quality standard White / Ivory Glazed Tiles ISI marked [IS : 13753] of size 300 mm x 200 mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster on walls and pillar). Catgory-I : Kajaria, Johnson, , Somani make etc. 30 Providing and fixing 1st quality MAT finished ceremic tile size 300 x 300 mm confirming to IS : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (Untile of Roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of the complete (including the cost of cement mortor bed1:4).Catgory-I : Kajaria, Johnson, , Somani make etc. 31 ExtraforusingMarbleprinted/Graniteshadeordarkshadetilesinsteadofwhite,grey,ivory,fumeredbrown,lightgreen,lightblueandotherlightshadesinglazedtilesandMATfinishedtiles. 32 a.) Wall Tiles 33 b.) Mat Tiles 34 Extraforusingsize above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finishedtiles in place of 300mm x 300mm size. 35 Providing & fixing vitrified paving tiles size 600 mm × 600 mm × 12 mm thick fix with cement mortar over 20 mm thich (1 Cement 4 Sand) laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (Untile or Roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (including the cost of cement mortor 1:4)Category -A : Kajaria, Jhonson, Somani make 36 Polished Blue Kota Stone slab in steps, walls, pillars having fine machine cut edges laid on 12 mm (Av.) thick cement mortar 1 : 3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete : 30 mm thick slab area 2001 to 5000 Sq.Cm. 37 Polished Blue Kota stone flooring skirting, laid over 20 mm thick base of C.M. 1 : 4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete :For area of each slab from 2001 to 5000 Sq.Cm :25mm thick 38 Add extra for mirror polishing on terrazo / mosaic flooring : 39 Rough chisel dressed stone flooring over 20 mm (Av.) thick base in CM 1 : 6 including pointing with cement mortar 1 : 2 (1 cement : 2 stone dust) with and admixture of pigment to match the shade of stone with joint thickness upto 15 mm : 35 mm thick red sand stone. 40 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of 1st course of applying cement slurry @ 4.4 Kg./sqm mixed with water proofing compound Impermo of Snowcem or equivalent conforming to IS 2645 in recommended proportions. IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg. per sqm of area. IVth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ Kg./Sqm). 41 Filling of sunk portion of roof with earthen pots of required height including filling voids with 1 : 2 : 4 light concrete, using brick bats complete leveling and dressing the surface by 50 mm thick cement concrete 1 : 2 : 4 as per specification. 42 Random rubble dry stone Kharanja under floor. 43 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc. Complete fine finish: 25 mm thick 44 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc. Complete fine finish: 20 mm thick 45 6mm thick cement plaster to ceiling of mix 1:3 ( 1 cement: 3 Coarse aggregate) 46 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc. Complete fine finish: 12 mm thick 47 Making Grooves as per design in plaster 10mm to 20mm wide 48 Making of drip course (Tapka) in cement sand mortar 1:6 width up to 40mm and 10mm thick as per approved design 49 Decorative plaster work with spectrum textured coating as per approved colour and shade complete as per manufactures specifications.PERKY-FINE TEXTURED- (Roller Finish) av. Thickness 400 to 500 microns. 50 Painting with Acrylic Exterier Paint Birla/Nerolac/Asian/Berger of Equivelant of approved brand to give and even shade with all scaffolding two or more coat on new work after cleaning of existing surface complete in all respect. As per direction of Engineer in charge. 51 Finishing wall with vinyl satin finish coating paints of approved shade with two or more coats including sand-papering, priming coat, making surface with putty or plaster of Paris etc. complete in all respects : New work 52 Providing & laying Chequerred terrazo tiles of approved make 22 mm thick with marble chips of size upto 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete in all respect as per specification, on 28 mm thick bed of CM 1 : 4 : Dark shade using ordinary cement. 53 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completeBirla/J.K./Nerolac or ISO. As per direction of Engineer in charge. 54 Excavation for roadwork in soil with hydraulic excavator of0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per MoRTH Specification Clause 301.3 55 Providing and fixing anodized aluminium work (Anodizing to be got done from approved Anodizer) for doors, windows, ventilators and partition with extruded built up standard tubular and other sections of approved make confirming to IS : 733 and IS : 1285 anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasterners including necessary filling up of gas at junctions, at top, bottom and sides with required PVC / neoprene felt etc.; Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, Al. Tower bolt & Al. handle & Al. Aldrop etc. all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately).For fixed portion 56 For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). Powder coating aluminum( minimum thickness of powder coating 50 micron) 57 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost of aluminium snap beading shall be paid in basic item).With glass panes of 5.0 mm thickness (weight not less than 13.75 kg./sqm) as per IS : 2835. 58 Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. With stainless steel cover plate 59 Providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminum window/vent with required screws, Y and H aluminium sec (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge.Polyester Powder coating aluminum( minimum thickness of powder coating 50 micron) 60 Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 61 Powder coating aluminum( minimum thickness of powder coating 50 micron) 62 Providing and fixing steel glazed window frame made out of 80 x 40 mm hollow sheet section of 16 gauge thickness, joint mitred welded and grinded including hold fast of steel lugs 13 mm x 3 mm and 15 Cm long embedded in C C block 15 x 10 x 10 Cm of 1 : 3 : 6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 55 x 20 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10 mm x 10 mm square bars welded to frame for paitam fixing float glass 4 mm thick panes with glazing clips and metal sash putty and fixing of shutters frames, peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in-charge. Window Openable 63 Window fixed. 64 NF) Extra for additional shutter in pipe section windows with wire gauge 14 mesh x 24 gauge 65 Providing and fixing Square bars or other flat welded to window, ventilators etc. 66 Providing and fixing pressed steel mitreddoor frames confirming toIS 4351 manufacturing from commercial mild steel sheet of 1.25 mm( 16 gauge) thick ness including hinges jamb, lock jamb head and if required angle thresh hold of mild steel angle of section 50x 25 m , or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means , adjustable lugs with split and tail to each jambs including butt hinges 2.5 mm thick with mortar guards , lock strike plate and shock absorber as specified and aplying a coat of approved steel primer after pre traetment of the surfaceincluding filling with CC 1:2:4 (M15 grade) complete as directed by engineer incharge :-Profile B 67 Profile C 68 Profile E 69 Supply and fixing in cement mortarwelded hand railing made out of M.S round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paide extra) with priming coat red oxide.Stair 70 Extra for Providing D type pipe head as top of Hand Rail 71 Providing and fixing steel gate grating and grills made of angles,tees,square bars or other flats black pipe with holdfast and fittings complete per design and drawing including cutting welding and fabrication with priming coat of red oxide. 72 b) Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 73 Providing and fixing 1 mm thick M.S. sheet sliding-shutters with frame & diagonals braces of 40 x 40 x 6 mm angle iron 3 mm M.S. gusset plates at the junction and corners, 25 mm dia pulley, 40 x 40 x 6 mm angle and T-iorn guide at the top and bottom respectively including applying a priming coat of approved steel primer. 74 Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size.Welded mesh 25 mmx 25 mm x 16 gauge. 75 Renewing glass panes, with putty and nails wherever necessary:Float glass panes of thickness 5.5 mm 76 Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of T-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension).With 75 mm opening when closed. 77 Providing and fixing external grade board solid core single lesf flush door shutters ISI 2202-67 marked using Phenol formal , dehydreresion in glue both sides with approved steel fitting complete as per Annexure A Commercial Veneer both side 35mm thick shutter. 78 Extra for providing external lipping with 2nd class teak wood battens6mm minimum depth on all edges of shutter (over all area of door shutter to be measured) over item BSRitem no 8.13 79 Painting with enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work. 80 Providing and fixing powder coated aluminium 1.5 dia drapery rod with finials, rings end cap cording set and bracket etc. complete of approved make (Arolux, Mac, Vista or eqvi.) and approved design as per specification and direction of engineer-in-charge 81 For first 0.90 meter length of rod. 82 For subsequent length of rod (beyond 0.90 m length covered in item 1 (a) above). 83 P&f rigid PVC Pipe (IS:4985 mark ) class 2nd (4Kg. / Cm) approvd quality / make including joining the pipe with solvent cement rubber ring and lubricant.110mm dia. 84 P&F rigid PVC pipe fittings (IS; 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant 110mm dia. 85 Door Tee110mm dia 86 Bend 45 110mm dia 87 Door Bend (Left & Right)110mm dia 88 Pipe Clip 110mm dia 89 Lettering with black Japan paint of approved brand and manufacture. 90 Part B Rain Water Harvesting 91 Construction oftubewell up to 100m depth and above to accomodate housing and assembly pipe in all types of alluvium strata by rotay drilling method with code of practice for construction and testing of tubewells (IS:2800 (Part-II) : 1991 and IS:2800 (Part-II) :1979 both amended up to date) with supply of bail plug if necessary.The work will not include cost of housing pipe and strainer pipe assembly cost, gravel and development work. Work would be deemedcompleted only after obtaining sound free water during pumping.200 mm nominal bore 92 Construction of Recharge Shaft in filter pit including Earth work Excavation , lifting excavted earth with all lift and 50 m lead and centering & shuttering evenever required. Diameter 900 mm 93 Supply & fixing Pre-cast RCC Rinngs at the mouth of recharge shaft of M20 mix with40 mm thickness Diameter 900 mm 94 Supply & lowering air line of 25mm dia, G.I. pipe B class having perforation 3 to 5mm size all arrow of G.I. pipe in Zig-Zag fashion & making air vent at top including the cost of Tee-Nipples, Elbow, Socket etc. 95 Supply and lowering vent air pipe 63mm dia rigid PVC pipe(IS 4985) mark class II (4kg per cm2 ) with required all necessary fittings including perforation of 3 to 5 mm size all around the pipe at a distance of 180 to 220mm in zig zag fashion and making air vent at top complete as per direction of Engineer incharge. 96 Supply & lying River-gravels of following sizes in recharge shaft, filter pit after screening & washing from kachha shift without deduction of voids 97 Size 9 to 12 mm 98 Size 3 to 5 mm 99 Supply & laying of clean, clear sharp river sand of size 1 to 2mm coarse, without deduction of voids. 100 Part C Tube well 101 Construction of tube well from ground levels and upto 100 Meter depth and above to accommodate housing and assembly pipe of following size in all types of alluvium strata by percussion / rotary drilling method and with gravel as per IS : 4097-1967 and packing as per IS : 2800 (Part- I & II) 1979 as amended upto date (the work includes the cost of gravel & Its primary packing and packing during development, lowering of housing & strainer assembly pipes, with supply and wrapping of coir rope, wherever necessary, for arresting fine sand particles. The work will not include cost of housing pipe and strainer pipe assembly and development work, but work would be completed after obtaining sand free water. 200 mm dia nominal bore 102 Construction of Tube-well upto 100 Meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casingpipes as per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe: 200 mm dia Nominal bore. 103 Development of tube well as per IS specification using suitable compressor to give sand free water for required yield of the gravel packed tube well. 104 Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work. 200 mm Nominal bore of pipe 105 Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985. 106 S & F tube well cover ofM.S.sheet (6mm thick) with nuts and bolts complete for casing size: 107 S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 108 Providing & lowering of G.I. Pipes, flange pipe including rubber washer and nuts of8 mm dia complete in all respect I.S.I. Make. B Class 50 mm dia 109 Supplying and installation of submersible pumping motor pump sets I.S.I. Marked (IS : 8034-1989 ) of approved make like K.S.B., KIRLOSKAR, Calama etc. or equivalent, making connection suitable for T.W./D.C.B./Open well. The job includes screwing and welding offlanges on G.I. riser pipes, installation of complete fitting and accessories, with riser pipes, jointing of electrical cables and other connections making switch board electrical connections, all labour for testing of submersible pump set and supply of water to water mains, complete in all respect (Refer Electrical BSR ) 150 mm diameter submersible pump shall have following rating,5HP, 1#phase, (55-150)Mtr, (166-60)LPM 110 P/Laying ISI marked P.V.C. insulated submersible cable confirming to IS:694 with flexible copper conductor including making connection etc. as required. GP1 111 4.0 Sq.mm 3 core flat / Round 112 Supply and fixing of Oil / Air break Starter panel made out of sheet steelpowder coated enclosure comprising of over load protection relay, short circuit & single phasing protection, ON / OFFpush buttons,ammeter, voltmeter, indicating lamps etc. complete in all respect suitable for following rating motors. GP1 113 For single phase Submersible / Monoblockpump 114 0.5 HP to 3.0 HP 115 Part D - Sanitary work 116 P&F Indian type white glazed vitreous china 1st quality W.C. Orissa pan( IS. 2556 Mark) with 100 mm vitreous china Por S trap including cutting and making the wall and floor. Size 580mmx440 mm 117 P & F Europeantype white glazed vitreous china 1st quality W.C. (IS : 2556 Mark) including cutting and making good the wall and floor Wall Mounting (syphonic) 118 P & F water closet Seat Covers with brass hinges complete :Solid PVC (ISI marked)White 119 P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall:WVC for symphonic EWC. 120 P & F WVC wash basin (1st quality, I.S. : 2556 Mark) of approved make with C.I. brackets duly painted, 1 No. 15 mm C.P. Pillar cock (IS : 8934 Mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall.: Size 550 mm x 400 mm dia for counter top 121 P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete.Flat Back (large) or half stall size 590x375x390mm. 122 b) P&F W.V.C.(IS:2556)Squatting Urinal of standard make complete,including cutting and making good the wall and floor : size 450X350 mm 123 P&FC.P.brassUrinalFlushPipeset complete with flanged brackets of approved make.For 3 Urinal 124 P & F C.P. brass Urinal Spreader for stall urinal of approved make. 125 P & F Marble. Urinal Partition slab both sides polised of approved design cut from marble size 900X600mm. Makrana Albeta marble having light spreaks 126 b) P&F W.V.C. Half- round channel of approved make in C.M. mortar 1:3, Joints finished in white cement of :size 150mm 127 P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor :1.0 mm thick Salem stainless steel AISI -304 kitchen sink of approved make (Nirali, Neel – kanth, Jaina, Faber-Castell )with large waste coupling. 37x18x7…bowl size(17x15x7(with drain board) 128 P & F Bottle Trap of approved make :C.P Brass 40 mm 129 P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. 130 Glass Shelf with edges rounded off Anodised Aluminium angle frame & C.P. brass brackets & guard rail size 600x120mm 131 P & F Towel Rail or Ring of approved quality/make: 132 a) C.P. brass Towel Rail elbow type with concealed screws size 600 mm (Heavy duty). 133 b) C.P. Brass Towel Ring revolving type 134 P & F Grating of approved quality/make: 135 Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make 136 P & F Tooth Paste & Brush Holder of approved quality/make: 137 Stainless Steel 138 P & F Shower arm 15mm dia of approved quality/make. 139 (-do-) size 370mm.(-do-) 140 P & F Bath Shower of approved quality/make. 141 C.P. brass of Heavy & superior quality, revolving with adjustable key 150mm. 142 P & F Extension Pipe for bib cocks of approved quality/make. 143 (-do-) 150 X 15mm. 144 P& F Sink Cock of superior quality and approved make : CP Sink Cock, Casted spout 15mm 145 P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. 146 Providing & fixing C.P.flange for 15mm dia taps. 147 P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:C.P. Brass bib cock,15mm nominal bore. 148 (-do-) Long body, 15mm nominal bore weight not less than 690 gm 149 P & F Stop Cock(IS :8931 Mark),superior quality & ofapproved make: 150 (-do-) Concealed Stop Cock 15mm. 151 P&F Ball Cock (IS-1703) with rod & PVC ball complete Brass wt.400 gm,15mm. 152 P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. with 37 Cm. long pipe and nut. 153 P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : 154 a) Gun-metal 15mm nominal bore. 155 b) (-do-) 25mm nominal bore. 156 P & F PVC Storage Tank ISI Marked (IS : 12701) indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 1,000 litres capacity. 157 Hoisting charges for each floor 158 P & F Square-mouth gully trap `A` grade (IS :marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type.Trap size 225 X 150 mm, 15 Kg. C.I. cover with frame Internal Chamber size 450 X 450mm. 159 P&F rigid PVC Pipe (IS:4985 mark) class II(4 Kg. /Cm.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant 160 110 mm dia 161 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: 162 a) Bend 87.5 Dg. 163 110mm dia 164 b) Coupler (socket) 165 110mm dia 166 c) Pipe Clip 167 110mm dia 168 d) Plain Tee 169 110mm dia 170 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 171 a) 75 mm dia 172 b) 110 mm dia 173 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 174 a) Coupler 175 75mm dia 176 110mm dia 177 b) Bend 87.5 Dg. 178 75mm dia 179 110mm dia 180 c) Single Y 181 75mm dia 182 110mm dia 183 d) Door Bend 87.5 Dg. 184 110mm dia 185 e) Single Tee with Door 186 110mm dia 187 f) Single Tee 188 75mm dia 189 110mm dia 190 g) Nahni Trap without Jali 4” 191 110mm dia 192 h) Plain floor trap 193 110mm dia 194 i) Vent Cowel 195 110mm dia 196 Construction of manhole in all type of soil inner size 90 X 60 Cm. 450 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring,making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, 25 k.g C.I. cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead.Depth up to 0.5 M 197 Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m 100 mm thick C.C. 1:5:10 in foundation, 20mm thick inside plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. size 450 x 450mm depth upto0.5 M & 15 k.g. C.I.cover with frame 198 Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C flooring & over stone slab covering ,80 mm thick slab ,jointing of slab in CM 1:3. Ralthal, Kharanja,50 mm thick stone partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos C.I foot rests of approved design ,two No. 450 mm dia 25 k.g.each Ferro C.I. cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-Size 400x140x150cm (for 50users) 199 ,-Do-Size 200x100x130 cm.(for 10 users) 200 -Do- Size 230 x110 x150 cm.(for 20 users) 201 Construction of Soakage well in all types of soil of approved drawing, top 90 Cm .Portion in 450mm thick masonry with CM 1:6, 80 mm thick stone slab covering,jointing of slab in CM 1:3 ,Ralthal, kharanja 40mm thick M-15 grade C.C flooring, earth worketc . complete including disposal of surplus earth within a lead of 50 mtr . Inner dia90 Cm & 10 to 12 Mtr deep. 202 Add extra if Soakage Well is filled with dry stones. 203 P & F G.I. Pipes (External Work) with G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc. 204 a) 15mm dia nominal bore B Class 205 b) 25mm dia nominal boreB Class 206 P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: 207 Exposed on wall 208 a) 15 mm dia nominal boreB Class 209 b) 25mm dia nominal boreB Class 210 Concealed pipe in wall including painting with anticorrosive bitumen paint 15 mm dia nominal boreB class 211 Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size : 212 a) 15mm dia nominal bore 213 b) 25mm dia nominal bore 214 P & F Pilllar Cocks (IS :8934 Mark) of superior quality and approved make: 215 C.P. Pillar cock, 15 mm dia nominal bore 216 P & F Soap Dish or Tray of approved quality/make CP Brass 217 P & F Towel Rail or Ring of approved quality/make:C.P. brass Towel Rail elbow type with concealed screws size 600 mm (Heavy duty). 218 Construction of open surface drain with 112 mm thick brick masonry in cement mortar 1:4, 110 mm thick base concrete 1:5:10, 37mm thick M-15 Concrete, 12mm 1:4 cement plaster on all exposed faces of walls including top surface excavation and disposal of earth complete as per approved design/drawing (150mm drain 225mm avg depth 219 Providing Laying & jointing glazed S.W. pipes grade `AA` (IS;651 marked) of approved make with spun yarn & stiff mixture of cement mortar 1.1 excavation & refilling of earth in all types of soil upto 1.2m depth, S.W. fittings, including testing of joints etc, complete. 150mm dia 220 Providing & Laying C.C. 1:5:10 (Stone aggregate 40 mm nominal size) upto haunches of S.W. pipes including 150 mm thick bed concrete as per Rajasthan P.W.D. specifications (Width W=Dia of pipe in Cm+40Cm.) concrete width to be reduced from width W at center of pipe to 0 at top of pipe (Excluding cost of pipe). 150mm dia S.W. Pipe. 221 Construction of Cement Concrete Chamber 125mm dia on depressed floor upto 45cm height from floor with : 222 C.P. Brass grating 223 Construction of Cement Concrete Chamber 125mm dia. 224 C.P. Brass grating 225 Part G - Electrical work 226 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) ofapproved make in surface / recessed ISI markedMMS ( IS:9537 P - III ) PVC conduit & its accessories, round tiles,18 SWG M.S. box with earth terminal, 6 A switch, 3.0 mm thick ISI marked phenolic laminated sheet, zinc plated / brassscrews, cup washers, making connections, testing etc. as required. GP1 ( use semi moduler accessories) 227 Short point (up to 3 mtr.) 228 Medium point (up to 6 mtr.) 229 Long point(up to 10 mtr..) 230 Wiring of twin control light / fan / call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) of approved make in surface / recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & its accessories, round tles,18 SWG M.S. box with earth terminal, 6 A two way switch, 3.0 mm thick ISI marked phenolic laminated sheet, zinc plated / brassscrews, cup washers, making connections, testing etc. as required. GP1 ( use semi moduler accessories) 231 Long point(up to 10 mtr..) 232 Wiring of 3 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved makein surface / recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & its accessories, 18 SWG 175 mm x 100 mm x 60 mm M.S. box with earth terminal,6 Aswitch, 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet, zinc plated / brassscrews, cup washers, making connections, testing etc. as required. GP1 ( use semi moduler accessories) 233 On board 234 Short point (up to 3 mtr.) 235 Medium point (up to 6 mtr.) 236 Long point(up to 10 mtr..) 237 Supplying and fixing of power plug point accessories on 18 SWG metal box of size 175 x 100 x 60 mm. on surface or in recessed with suitable size phenolic laminated sheet cover including cost of 6 pin 16 amp. Switch and socket outlet, making connection , testing , etc. as required. GP1 ( use semi moduler accessories) 238 In Item no. E020100, E020200, E020300 The rates are for flush type PC / Urea series accessories ,for using semi modular PC / Urea series accessories, rate shall be increased 2 % in point wiring rate( For item no. 1 to 4 ) 239 S&F following sizes (dia.) of ISI marked medium duty PVC conduit along with accessories in surface / recessed using saddles, clamps, fastener as required includingcutting the wall, covering conduit and making good the same as required.Gr I 240 20 mm 241 25 mm 242 32 mm 243 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existingsurface or recessed conduit/casing capping including making connections etc. as required.Gr I 244 3x 1.5 sq.mm 245 2 x 2.5 sq. mm. + 1x1.5sqmm ( All light and power Ckt) 246 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. (AC Ckt) 247 4 x 6.0 sq.mm (Sub main) 248 1 x 4.0 sq.mm (With sub main ) 249 P&F 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic) ISI marked IS 8828(1996)]/ conforming to IEC 60898 in existing board/sheets including making connections, testing etc. as required.Gr I 250 Single pole MCB 251 6 A to 32 A rating 252 Double pole MCB ( for UPS and AC Point ) 253 6 A to 32 A rating 254 Four pole MCB 255 40 A 63 A rating 256 Triple pole MCB 257 40 A 63 A rating 258 P&F Recessed/ Surface mounting heavy duty horizontal type sheet steel Distribution board phophatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, conforming to IS13032 & IS8623 including making internal DBterminations with copper lugs , testing etc. as required.Gr I 259 Double door (single phase) 260 4 Way 261 Double door (Three phase) 262 6 Way 263 P&F recessed/ surface mounting heavy duty Vertical type 16 SWG sheet steel Distribution board with provision of incomer suitable for MCCB and SP / TP MCB as outgoing ,phophatised ,powder painted complete with insulated suitable ratingcopper bus bar , neutral link, earth link and din bar, masking sheet & conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as required. GP1 264 Double door with Provision of Incomer MCCB 100 / 125 A Rating 265 6 Way 266 P&F flush/surface type enclosure for housing MCB/Isolator with Din rail including making connectionswith lugs, repairs etc. as required. GP1 267 With sheet steel enclosure 268 Two way 269 P & F ISI marked following semi modular accessories with decorative cover plate of approved colours including making connections testing est. as required GP1 270 RJ-11 telephone jack single two line 271 RJ-45 computer jack with shutter 272 5 step fan regulator 273 T.V. socket single outlet 274 P & F following size hot dip galvanized M.S. box of 20 SWG with earthing terminal in recess/ surface suitable for modular accessories as required. GP1 275 1-2 Module 276 P & F following size mounting grid plates with cover plates GP1 277 1/2 Module 278 SITC of quick make and quick break3 pole current limiting MCCB having following current rating, short circuitbreaking capacityat 440/415 V, 50 Hz; O/L & S/C settings and conforming to IS 60947-2 / IEC 60947-2 with frontface and centralised adjustable, line load interchangeability, having positive isolation capability, provision for UVR , shunt trip , earth fault trip, push( test) to trip, including making connections with lugs & spreaders,etc. as required. GP1 279 With Thermal Magnetic release 280 up to 100 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu 281 P/Laying P.V.C./ XLPE insulated & P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor of IS:1554 P-I / IS :7098 P - I of Group 1 of approved makein ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,IInd class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size.Armoured 282 10.0 Sq.mm 283 4 core ( For Submersible pump) 284 25.0 Sq.mm 285 3.5 core ( For main line) 286 Supplying and making one end termination with heavy duty single compression brass gland SIBG type, heavy duty aluminium lugs duly crimped with crimping tool, PVC tape etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size. 287 4 x 10.0 sq.mm 288 3.5 x 25.0 sq.mm 289 P / L of Double wall corrugated HDPE pipe confirming to IS : 14930 P - 1 & 2with HDPE Coupler at 1 mtr. Depth below the ground for laying cable including making the trench and back filling , compaction of earth as required of Gemini or IS:14930 marked make.Outer Dia. / Inner dia. 290 110 / 95 mm 291 Plate Earthing as per IS:3043 with G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying3 to 4 mtr. below the ground level with 25mm dia. G.I. B class watering Pipe including all accessories like nut, bolts, reducer ,nipple, wire meshed funnel, and C.C.finished chamber covered with hinged type with locking arrangement C.I. Cover,C.I. Frame of size300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. 292 Maintenance free Gel EarthingwithPipe in pipe / Pipein striptechnologyfilled with anti corrosive conductive compound ( CPRI Tested )below the ground in 150 - 200 mm dia. earth pit & surrounding filled with required mineralfillingcompound ( MFC should have hygroscopic property to retain the moisture for long time to create low resistance zone) and C.C.finished chamber covered with hinged type with locking arrangement C.I. Cover,C.I. Frame of size 300mm x 300mm complete testing of earth resistance as required. of following sizes. 293 With Pipe in Pipe Technology (Inner pipe dia. / Outer pipe dia. ) 80 - 100 micron GI Coating 294 GI pipe 2000 mm long, 50 / 25mm, Terminal 12 mm GI Strip 295 S & Laying following size earth wire/stripin horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. 296 25mm x 6mm G.I. ( Hot Dipped) Strip 297 8 SWG G.I. ( Hot Dipped) Wire 298 P&F 1200mm sweep BEE 5 star rated double ball bearing capacitor start, aluminium body & blade ceiling fan complying to IS 374:1979, I/p 50 watt at max speed & 230 Volt, air delivery>210 CMM, Speed> 330 RPM with down rod upto 30 cm with 3 x 1.5 sqmm pvc insulated flexible copper conductor making connection testing etc as required. 299 P & F 18 swgM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . 300 P&F of Double ball bearing, capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible copper conductor ,making connections, testing etc. as required.Gr I 301 300 mm sweep 302 P&F of Heavy duty capacitor start, Double ball bearing900/1400 RPM single phase ISI marked Exhaustfan,IS:2312 marked in existing opening including making connections testing etc. as required. GP1 303 300 mm sweep(900/1400 RPM) 304 Supply & FixingISI marked( IS : 15683 )Portable Fire Exitnguisher, ABC type,finished externally with red enamel paint, completein all respects includinginitial fill and wall suspension of following capacity.GP1 305 6 kg 306 P & F of IP 65 protected LED Street Light fixture 70-75 watt (with surge protection device 10KA) applicable for area lighting with extruded pressure diecast aluminium housing, system lumens efficancy of 100 Im/watt minimum, toughened glass with diffuser, suitable lenses on LED, 240V, 50 Hz of High Power LED lamps supplied with pre-wired cable of 1 mtr. Integrated Driver shall be high efficiency having efficiency>85% and in compliance to IEC standards system life of 50,000 Burning Hours, CRI>80, PF>0.90 at full load, CCT 5700-6500 K (as per direction of Engineer incharge). Fixtures shall be CE compliance. 307 S & F of Street light bracket made out from following size of B class GI pipe with heavy duty pole clamp, Saddles suitable fastners etc. as required. 308 32 mm Dia. 309 Supply , Drawing and Testing of 4 pair, 24 AWG UTP Cat 6 Cable as per latest ammendments of TIA /EIA 568 B.2-1 Specifications in existing MS/PVC Conduits including making connections to Information outlets and Patch Panels with ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing required. GP 1 310 Supply and Installation of Information outlets made of high impact plastic body ABS FR Grade with spring loaded collapsible shutters in jack Recess, suitable for Cat 6 application complying to latest ammendments EIA/ TIA 568 B.2-1 Specifications in existing modular /MS Boxes along with necessory connections as required GP 1 311 Supply & fixing of Faceplate for Flush / SurfaceMount Information Outlets Single Aperture with screw hole covers & Icon Tree Size 86mmX86mm GP 1 312 Single Aperture 313 Supply , Installation, Testing and Comissioning of Wall mounted Communication rack with glass doors, handles ,lock , Top and Bottom Cable entries, Supports for mounting rack on wall , Cable managers, one Fan, Equipment mounting hardware, power supply box for supplying power to switches, fans etc along with earth continuity kit, Mcb, indicator, moulded power supply cable GP 1 314 9 U(44 mm ) wall mounted 315 P & F ISI marked gong bell including making connection testing etc. as required.GP1 316 P & F ISI marked flush/surface type buzzer including making connection testing etc. as required.GP1 317 P & F ISI marked single tone electronic call bell including making connection testing etc. as required.GP1 318 P & F ISI markedding dong/musical chime bell including making connection testing etc. as required.GP1 319 P & F IS:371 marked6 amp surface type ceiling rose including making connection testing etc. as required.GP1 320 P & F ISI marked6 amp bakelite batten/angle holder including making connection testing etc. as required.GP1 321 P/Laying ISI marked P.V.C. insulated submersible cable confirming to IS:694 with flexible copper conductor including making connection etc. as required. GP1 322 4.0 Sq.mm 3 core flat / Round 323 Supply and fixing of Oil / Air break Starter panel made out of sheet steelpowder coated enclosure comprising of over load protection relay, short circuit & single phasing protection, ON / OFFpush buttons,ammeter, voltmeter, indicating lamps etc. complete in all respect suitable for following rating motors. GP1 324 For single phase Submersible / Monoblockpump 325 0.5 HP to 3.0 HP 326 P & F of 4 star ratedvertical storage water heater with outer casing made of M.S.sheet finished with anti-corrosive powder coating,inner tank made of pure electrolytic copper/stainless steel / SPHP, Tubular copper sheathed and Nickel plated heating element/ twin ceremic cartridge heating element, stem type thermostat and thermal cut out,Dual indicating lamps for power supply and thermostat,PUF insulation, Pressure relase valve,fusible plug etc. as required held in position with 4 no. rack bolts,duly wired with 3 core 2.5/4.0 Sqmm PVC insulated & sheathed copper conductor and 16 A/25A three pin plug top,including making inlet,outlet heavy gauge C.P./ Flexible alloyconnection,testing etc. as required. GP1 327 25 Ltr. 328 P & F energy efficient/energy saving 9 watt IP 20 LED Bulb cool white, in existing holder/fixture as required, minimum 900 Lumen output, 25000 burning hours, CCT 5700 K or 6500 K (as per direction of Engineer incharge), ANSI Lamp efficacy minimum 100 lumen /Watt, CRI 80, Driver efficiency > 85%, PF 0.95 at full load/230 volt AC. 329 P & F of IP20 surface/recess mounted LED downlight made of pressure diecast aluminium housing, with heat sink and good quality reflector, high efficiency external driver, power consumption 14/15 watt, system lumen efficiency >80 lumen/watt, CCT 6000K (minimum) K, CRI>80, PF>0.9 life time 50,000 burning hours. 330 P&F of IP 20 LED tube light 20 watt external batten mode from CRCA sheet steel suitable to replace T-8/T-12 tube light, integral driver, 2000 luman + 5% tolerance system kuman efficiacy oh 100 Lm/watt minimum expected life time of 25000 burning hours, CCT 5700 K, ANSI, CRI 80, driver efficiency>85% , Life expectancy of driver min 30000 hrs. PF 0.95 at full load/230 volt AC. 331 P&F of 36 Watt IP 20 LED 2x2 fixture, Recessed / surface type, having efficacy of not less than 100 lumen / watt, made out from CRCA housing and with high purity / transmisvity duffuser for uniform light distribution high efficiency driver electronics and in compliance to IEC standard (integral with light fisture), life time of more than 50000 burning hours, CCT 6000K (minimum), CRI>80 driver maintaining PF>0.9. 332 SITC of MNRE approved & confirming to IS:12933 P-1,2,3&5 Flat Plate Collector type solar hot water system withcollector, insulated stainless steel storage tank with electrical back up , MS standfor Collector & Tank etc. as required. of following capacity. 333 500 litre/ day 334 CCTV CameraPart H (Non BSR Item but already Approved) 335 P&F of CE & ROHS Certified, IP65 protected “All in one” Solar streetLight luminaries made out from powder coated die cast aluminum alloy housing, comprising of mono-crystalline silicon solar panel, Controller (with MPPT function), PIR sensor can control by remote, Real time on/off function for auto operation of light & Lithium battery with 6 hour charging, 12-16 hours discharge on full power mode and 30-36 hours discharge on power saving mode. With High Power LED’s having individual lens to achieve beam angles, LED Make: Osram, Phillips, Bridgelux, CREE. 336 12 watt LEDSolar Panel : 18V, 38WHBattery: 12.8 v, 15AHLumen:1200-1320 LM 337 Infrared Bullet / Dome Camera 338 Supply of 2 MP HD Analog IR Bullet Camera, CMOS/CCD, Min. Illumination 0.01lux (color) & 0lux with IR or better, upto 1920×1080 @ 25fps or better resolutions, 3.6mm fixed lens, able to provide 80° or better angle of view Day/Night, 20 Meter or better IR Range, S/N Ratio >62db or better, shutter speed 1s ~ 1/50,000s, True WDR 120db or better, AGC, White Balance ATW, BLC, DNR, Mirror, 12V DC, power consumption should not be more than 7W, able to work in -40° ~ 60°C temperature or better,IP66 rated housing with fully metal body, complete with mounting accessories. UL, CE and FCC CertificationApproved Makes: LG / SAMSUNG / HIKVISION 339 16 Channel Digital Video Recorder 340 Supply, Installation, Testing and comissioning of 16 Channel Digital Vedio recorder to support 16-ch 1080P video input with 2 slot for HDD. HDMI output, 1080P playback resolutions, bit rate 32 kbps-10Mbps, complete in all respect as per aboev specifications ( (DVR Approved Makes : Hikvision, Samsung, LG). NVR and Camera should be of the same make for smooth functioning. 341 SITC of 4 TB Surveillance HDD (Approved Makes: Seagate) 342 SITC of SMPS Power Supply required for the above 16 cameras (Standard make) 343 SITC of wiring for analoge camera video and power composite cable (3+1) 344 Supply, Installation, Testing and Commisioning of good quality of BNC connector, complete in all respect. 345 Supply, Installation, Testing and Commisioning of good quality of DC PIN connector, complete in all respect. 346 Supply of 19 (18.5”) Full HD LED / LCD Security Monitor, LED-Backlit TFT LCD technology with 1366×768 resolutions, Wide view angle: 90°(H)/65°(V), 3D comb filter, 3D De-interlace, 3D noise reduction, HDMI, VGA input, High reliable components for 7×24 working, Brightness: 200cd/m2 or better, Contrast: 600:1 or better, Color: 16.7m or better, VESA stand, power consumption not more than 25W, with HDMI Cable and mounting accessories Approved Makes: LG / SAMSUNG / HIKVISION / HONEYWELL
|