}

Tender For Modernization, Improvement, Upgradation Including Providing And Installation Of Hvac, Automated Firefighting System And Addition/Alternation In First Floor Of Town Hall Building, Jammu, jammu-Jammu And Kashmir

Jammu Municipal Corporation-JMC has published Tender For Modernization, Improvement, Upgradation Including Providing And Installation Of Hvac, Automated Firefighting System And Addition/Alternation In First Floor Of Town Hall Building, Jammu. Submission Date for this Tender is 06-12-2022. Fire Protection System Tenders in jammu Jammu And Kashmir. Bidders can get complete Tender details and download the document.




Tender Notice

34984268
Tender For Modernization, Improvement, Upgradation Including Providing And Installation Of Hvac, Automated Firefighting System And Addition/Alternation In First Floor Of Town Hall Building, Jammu
Open Tender
Indian
Jammu And Kashmir
jammu
06-12-2022

Tender Details

Modernization, Improvement, Upgradation Including Providing And Installation Of Hvac, Automated Firefighting System And Addition / Alternation In First Floor Of Town Hall Building, Jammu

Key Value

Document Fees
INR 10000 /-
EMD
INR 1164820.0 /-
Tender Value
INR 5.82 Crore /-

BOQ Items

Name of Work: Modernization, Improvement, Upgradation including providing and installation of HVAC, Automated firefighting system and addition/alternation in first floor of Town hall Building, Jammu
Sl. No. Item Description
1Providing and Fixing Armstrong/ Himalayan Acoustics/ Hunter Douglas /Ecophone or equivalent as approved by Engineer-in-charge SoundScapes - Acoustical clouds which are 30 mm thick, flat glass fiber panels with Humidity Resistance RH 90% & Recycled Content of minimum 30%, come in various shapes in the color specified by the Architect.The back of each panel to have embedded square frame bracket system of 610x610mm in for suspension of individual or grouped panels. The panels to be suspended using hanging kit consisting of(gripper structure anchors with an outer diameter of 16mm and height 23mm, aircraft cables of 1.5mm dia 2.44 LM in length and bottom end cable adjusters of 8.9mm outer diameter) 3.66m Aluminum group carrier frames, frame alignment spacers and panel hooks of sizes 115mm & 90mm.2 Aluminum group frames to be used which are cut to size of 1931mm. Also 4 pieces of size 712mm of Aluminum group frames would also be required. Two Aluminum carrier frames to be placed parallel to each other and at a distance of 406 mm with their open face down and would form the ‘lower’ frame. The 712mm pieces of carrier bar to be placed parallel to each other at every 1219mm with their open face up and should be placed on top and perpendicular to the ‘lower’ frame thus forming the ‘upper ‘ frame using the frame alignment spacerswith the first and the last ‘upper’ frame pieces to be placed at 356mm from the ends and the assembly is secured with nut and bolts passing through the ‘upper’, ‘lower’ and the frame alignment spacers at every intersection.The assembly to be suspended to the soffit using the deck hanging kit and the levels to be adjusted using the bottom end cable adjuster. 4 panel hooks to be screwed on the embedded square frame bracket at the back of each panel such that the two 115mm ‘High’ hooks are opposite to each other and are at the 203mm off centre mark of the embedded square frame bracket and the two 90mm ‘Low’ hooks are opposite to each other at the centre mark of the embedded square frame bracket. SoundScapes Panels to be suspended on the Aluminum group frames by engaging the High hooks to the ‘upper’ frame and the Low hooks to the ‘lower’ frame. Installation to be carried out by OEM Trained Installation team & Installation as per recommended procedure.
2Providing and fixing at all height wooden false ceiling including providing and fixing of frame workof India gypsum /Lafarge /USG Boralor equivalent as approved by Engineer-in- chargemade of special sections power pressed from MS sheet and galvaised in accordance with zinc coating of grade 350 as per IS 277 and consiting of angle cleats of size 25mm widex1.6mm thick with flanges of 22 mm and 37mm at 1200 mm c/c one flange fixed to the ceiling with dash fastner 12.5 mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x.55mm of required length, and other end of angle hanger being fixed with nut & bolts to GI channels 45x15x.9mm running at the rate of 1200 mm c/c to which the ceiling section .5mm thick button wedge of 80mm with tapered flages of 26mm each having clips of 10.5mm at 600mm c/c shall be fixed in a direction perpendicular to GI channel with connecting clips made out of 2.644 mm dia x 230mm long GI wire at every junction including fixing the gypsum board with ceiling section & perimeter channels .5mm thick 27mm high having flanges of 20mm & 30mm long, the perimeter of ceilin fixed to wall /partition with the help of rawl plugs at 450mmc/c with 25 mm long drywall screws at 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recomended filler, jointing tapes, finisher and 2 coats of primer suitable for board as per manufacturers specifications and also including the cost of making opeings for light fittings,grills,diffusers,cutouts made with frame of perimeter channels suitably fixed all complete as per drawings and specifications and direction of the architects. The contractor shall screw onto the GI framework 18 mm thick WPC Grade 1 board of Asian/BVW/Greenlam using countersunk screw to give a smooth flush finish. On this shall be fixed 4mm thk veneer ply of century/ euro/ greenlam/merino/decowood pasted on WPC board with bonding agent like fevicol etc and using headless nails. The veneer ply shall be installed in desired pattern & design as per detailed drgs including grooving, panelling battens etc. the finished veneer after repairing and sanding shall be finished in water based low VOC polyurethene polish of asian paint/ MRF/ Sircain matt/ gloss finish to be spray finished in desired shade complete in all respects as per manufactureres specifications.the rates quoted are inclusive of all GI framework, MDF panelling, Veneer plywood, polishing, labour, grooving, scaffolding, wastage etc complete in all respects as per detailed ceiling drgs given. The payment & measurement shall be made in Sqm of only for the finished visible area of the wooden ceiling. the base rates of the veneer for this shall be Rs 914 per Sqm so the contractor may quote accordingly.
3Providing and fixing at all height gypsum false ceiling of India gypsum /Lafarge /USG Boralor equivalent as approved by Engineer-in-charge including providing and fixing of frame work made of special sections power pressed from MS sheet and galvaised in accordance with zinc coating of grade 350 as per IS 277 and consiting of angle cleats of size 25mm widex1.6mm thick with flanges of 22 mm and 37mm at 1200 mm c/c one flange fixed to the ceiling with dash fastner 12.5 mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x.55mm of required length, and other end of angle hanger being fixed with nut & bolts to GI channels 45x15x.9mm running at the rate of 1200 mm c/c to which the ceiling section .5mm thick button wedge of 80mm with tapered flages of 26mm each having clips of 10.5mm at 450mm c/c shall be fixed in a direction perpendicular to GI channel with connecting clips made out of 2.644 mm dia x 230mm long GI wire at every junction including fixing the gypsum board with ceiling section & perimeter channels .5mm thick 27mm high having flanges of 20mm & 30mm long, the perimeter of ceilin fixed to wall /partition with the help of rawl plugs at 450mmc/c with 25 mm long drywall screws at 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recomended filler, jointing tapes, finisher and 2 coats of primer suitable for board as per manufacturers specifications and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawings and specifications and direction of the engineer-in-charge but excluding thecost of painting. The payment & measurement shall be made in Sqm of only for the finished visible area of the gypsum ceiling.12.5mm thick tapered edge gypsum board conforming to IS 2095- part1.
4Providing and fixing false ceiling tiles of Armstrong/USG/hunter Douglasor equivalent as approved by Engineer-in-charge of size 595x595 mm in true horizontal level suspended in inter locking metal grid of hot dipped galvanised steel sections (galvanised @170gsm/sqm) consiting of main "T" runner suitably spaced at joints to get rquired length and size of 24x38mm made from 0.30 mm thk (minimum) sheet spaced at 1200 mm c/c and cross tee of size 24x25mm made of 0.3mm thk (minimum) sheet, 1200 mm long spaced between main Tat 600 mm c/c to form a grid of 1200x600mm and secondary cross T of length 600mm and size 24x25 mm made of 0.30 mm thk (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making,opeings for services like diffusers,grills,light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats fixed to the ceiling with 6mm dia and 50mm long dash fastners,4mm GI adjustable rods with galvanised level clips spaced at 1200 mm c/c along main T , bottom exposed width of 24 mm of all the T sections shall be prepainted with polyester paint, all complete t all heights as per specifications drawings & as directed by engineer incharge.(the rate is excluding cost of tiles which will be paid seperately) . GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.
5Providing and fixing wooden and glass partition consisting of metal stud knurled partition (india Gypsum/ Lafarge make) or equivalent as approved by Engineer-in-charge which includes double sided layer of 8 mm thick Cement fibre board of Shera/ Visaka/ Ecoboard screw fixed to either side of 70 mm studs (0.55 mm thick having one flange of 34 mm another flange of 36 mm made of GI steel) placed 610 mm centre to centre in 72 mm floor and ceilng channel (0.55 mm thick having two equal flanges of 32 mm each made of GI steel) with joints staggered to avoid ‘through joints’. Finally the cement fibre boards boards are to be fixed and finished so as to have a flush look on which Premium acrylic emulsion paint shall be applied. the partition shall act as the bootom half of the system and shall be made to finish and fit as per the directions of the Engineer-in-charge. Payment shall be made only for visible area excluding fins, edges etc if any. (refer drg no partition FP1)
6Providing and fixing wooden and glass partition consisting of metal stud knurled partition (india Gypsum/ Lafarge make) which includes double sided layer of 10 mm thick Medium Density fibre (MDF) board of Century, Action Tesa, Green or equivalent brand as approved by Engineer-in-Charge screw fixed to either side of 70 mm studs (0.55 mm thick having one flange of 34 mm another flange of 36 mm made of GI steel) placed 610 mm centre to centre in 72 mm floor and ceilng channel (0.55 mm thick having two equal flanges of 32 mm each made of GI steel) with joints staggered to avoid ‘through joints’. Finally the MDF boards are to be fixed and finished so as to have a flush look on which 1 mm thick laminate of century/ euro/ greenlam/merino or equivalent as approved by Engineer-in-charge shall be pasted on both side and any visible edges with or without grooves.The partition shall also have10 mm thk toughened glass fixed in Dorma make WCPprofile all around the glass. glass work to be executed by a dorma authorised system integrator only. Glass to glass joint to be as per detailed drgs . glass work to be executed by a Dorma/ Geze/ yale/ Hettich authorised system integrator only. All patch fittings,door closers etc shall carry a company warranty of 3 years on a company letter head. The rates quoted should include the cost of glass, etching of glass, toughening, cutting of glass as per site, installation of doors, any support systems required etc complete in all respects as per detail drg and decision of engineer in charge. Payment shall be made only for visible area excluding fins, edges etc if any..(refer all partition drawings)
7Providing and fixing glass partition of 10 mm thk toughened glass fixed in WCP profile all around the glass as per detailed drgs glass work to be executed by a dorma authorised system integrator only. Glass to glass joint to be as per detailed drgs glass work to be executed by a Dorma/ Geze/ yale/ Hettich authorised system integrator or equivalent as approved by Engineer-in-charge only. The contractor shall be required to make the opening in the existing brick walls and shall also cast lintel beams if requred at site, he shall also plaster the edges of walls in gypsum plaster in plumb and make good all the damage to surrounding area for dismantling etc & plaster within this quoted rate. Nothing seperate shall be paid for any work for making & finishing the opeing except fr the glazed area. The rates quoted should include the cost of glass,etching of glass, toughening, cutting of glass as per site, dismantling of brick wall, casting of linte, removal of desbris etc , any support systems required etc complete in all respects as per detail drg and decision of engineer in charge. Payment shall be made only for visible glazed area excluding fins, edges etc if any.(refer drg no partition )
8Providing and fixing in position wallpaper of desired colour shade & texture ( baseprice rs 80 /sft all inclusive) to be pasted in place at desired location on walls/ partitions/ ceiling etc such that joints are not visible complete in all respects including, glue, cutting, wastage etc .
9Providing and laying full body thoughout section of tile same pattern prepolished/Matt vitrified tiles of 2" x2" of Neom by hindware/ Cera / Nexion/ Qutone makeor equivalent as approved by Engineer-in-charge (the base rate of the tiles all inclusive shall be Rs 646 /SqM) (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including wastage, grouting the joints with white cement and matching pigments etc., complete in all respects. the area of the tiles visible shall be measuered in SqM. Only difference in the base rate of the tiles shall be payble extra if more expensive tiles are used as decided by Engineer in charge.
10Providing and laying GVTprepolished/ Matt finish vitrified tiles of 32" x 64"/ 24" x 48" of Neom by Hindware/ Cera / Nexion/ Qutone makeor equivalent as approved by Engineer-in-charge (the base rate of the tiles all inclusive shall be Rs 915 /SqM) (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including wastage, grouting the joints with white cement and matching pigments etc., complete in all respects. the area of the tiles visible shall be measuered in SqM. Only difference in the base rate of the tiles shall be payble extra if more expensive tiles are used as decided by Engineer in charge.
11Providing and laying on toilet floors GVT/ Ceramic/ Vitirifed tiles of any size of Neom by Hindware/ Cera / Nexion/ Qutone makeor equivalent as approved by Engineer-in-charge (the base rate of the tiles all inclusive shall be Rs 646 Sq.M) (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including wastage, grouting the joints with white cement and matching pigments etc., complete in all respects. the area of the tiles visible shall be measuered in SqM. Only difference in the base rate of the tiles shall be payble extra if more expensive tiles are used as decided by Engineer in charge.
12Providing and fixing GVT/ Ceramic/ Vitirifed wall tiles of any size of Neom by Hindware/ Cera / Nexion/ Qutone makeor equivalent as approved by Engineer-in-charge (the base rate of the tiles all inclusive shall be Rs 615 Sq.M) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.the area of the tiles visible shall be measuered in Sq M. Only difference in the base rate of the tiles shall be payble extra if more expensive tiles are used as decided by Engineer in charge.
13Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade
14Providing and laying Polished Granite stone flooring in required design and patterns, in stairs, linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
15Providing and fixing one side wall panelling of 18 mm thk WPC board & 1mm thk laminate of desired shade onDrywall partition using India Gypsum/USG Boral floor and Ceiling channel (0.55 mm thick, 50mm wide & having two flanges of 30mm each) to the RCC Floor and Slab/ support structure with Approved Fasteners @ 600 mm Centersrespectively. Wall Studs are minimum 0.55 mm thick and Wall studs are placed at 610 mm centers in Floor and Ceiling channel. The partition shall be fixed with 18mm thick WPC board of century/BVW/ biowood on one side. The horizontal & vertical joints of the WPC boards on the metal framework must be staggered. Pasting of 1mm thk laminate of Greenply/ century/ Merino costing. The rates quoted are inclusive of scaffolding, fastneres, cutting of board for electrical points/ conduits etc.The rates also include GI farmework, WPC boards, all labour etc., fixing of veneer ply, polishing in matt melamine water based polish or high gloss water based polish as required by architect complete in all respects as per design. The measurement of this shall be in SQ. M. of partition area only inclusive of edge, only area ofpartition in elevation shall be payable any extra support or GI section shall not be payable in this item.
16Providing and laying water proofing treatment on toilet slabs by applying cement slurry mixed with water proofing cement compound TAPECRETE of CICO or equivalant of Sika/ Laticrete/ BSF/ Dr Fixit consisting of applying: a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on toilet wall and tucked into groove in wall all around. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry The work shall be carried out by a specialist agencygenerally is accordance with above specifications and shall carry a guarantee against leakage, seepage etc. for ten years.
17Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge.
18Providing & Fixing ofISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched Lamination of 1mm thickness of approved color and make on both faces of shutters orBVW / Zenex / Biowud Wood Fibre Composite Shutters of 35 mm Thick Heat Stabilized and High Pressure laminated on both sides inWenge or Dark Brown Shade (or any other shade as specified by the Architect / Client) Factory manufactured with 45 mm X 3 mm Thick Wood Fibre Composite Lipping in the matching color shade all around the sides of the Shutter (Green Certified by IGBC) having desired properties of (i) 100% Water Proof, (ii) 100% Termite Proof, (iii) Weather Resistant, (iv) Fire Retardant and (v) having Toxicity Level of less than 1. The rates quoted should include the cost of Ball Bearing Hinges (100 X 75 X 3 mm and 3 Nos.), SS Screws, 1 pair (back to back) of 300 X 22 mm tubular D type pull handle, 1 nos 300 mm long tower bolt, 1 nos SS door mounted floor stopper, 1 nos half dome floor door stopper complete in all respects for each door.(All Hardware shall be of SS 304 Grade of Dorma/ Dline /yale /hettich / Stanley/ Blum make and should be got approvedEngineer In-charge before installation)
19Supply of stainless steel door frame made up of 1.2 mm Thick ofSS 304 grade sheet door frame construction will be single rebate knockdown type jamb of 100 x 58 mm of Entrust, Synergy and Shakti make complete in all respects including fixing in place using Hilti/ wurth/ fisher 180mm fasteners including holes for fixing of hinges etc.
20Providing and fixing in various locations as scribbling boards 6mm thick lacquered glass of Saint Gobainmake in various colours in desired patterns pasted on 8mm cement fibre board of greenply/ nuwud/ asicor equivalent as approved by Engineer-in-charge make pasted using silicon sealant of 995 grade dow corning / alstone/ GE in similar colour as glass, mounted on wall using 25 mm Stainless steel 304 grade studs fixed to walls flush with no gap between wall and ply with studs installed on all 4 corners of glass of smaller sizes upto 600 mm wide & additional studs fixed at every 1000 mm at top & bottom for larger sizes. the glass shall be bevelled on the perimeter all around for a distance of 25 mm. the rates quoted are complete in all respects including fixing of studs, rawl plug, holes in glass bevelling etc complete in all respects.
21Finishing existing and new walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.The rates are inclusive of labour, scafolding, scrapping / removing of complete existing paint/ finish, preparation of surface as required for smooth final finish, acrylic putty filling if required, primer coats as described. (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm.,the work shoud be free from an or all defects, no difference in new & old constructin should be visible, the contractor shall have to keep putting coats till all the visible difference is removed within the same cost.
22Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : including in superstructure above plinth level upto floor five level Cement mortar 1:6 ( 1 cement : 6 coarse sand)
23Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in including extra for half Brick masonry in superstructure above plinth level upto floor V level. Cement mortar 1:3 ( 1 cement : 3 coarse sand)
24Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ per lite respectively conforming to IS: 2547(Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls and ceiling at all floors and locations, finished in smooth line and level etc. complete.
25Supply and installation of Merino-Besco/ Century/ Fundermaxor equivalent as approved by Engineer-in-charge toilet cubicles of width and depth as per specifications/site drawings. Cubicle height will be 1980 mm made from solid grade compact high pressure laminate as per IS:2046 and EN438- manufactured under high specific pressure > 5 MPa and temperature 120° C with bunch of kraft papers, impregnated with thermosetting phenolic resin and decorative wooden papers made of cellulose fiber, impregnated with thermosetting melamine resin which provides superior scratch, abrasion, heat, chemical, impact, graffiti and moisture resistance along with anti-bacterial properties. Panels have a black core that when machined, presents a distinctive black edge. All doors will be of single colour and made of 12 mm thick HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed to the pilasters. Stainless steel coat hook and stainless steel door knob. All the doors will be routed at the vertical ends and the rubber sponge lining will be incorporated at the routed ends. All pilasters will be made of 12 mm thick compact panel with chamfered edge and completed with stainless steel made lock set (comprised of thumb-turn and occupancy indicator). Pilasters will be anchored to the floor using stainless steel made adjustable legs. All pilasters will be routed at their vertical ends to facilitate closure of doors. All intermediate partitions or dividers will be made of 12 mm thick HPL compact laminate panels. They are affixed with stainless steel made U-channel at their ends for ultimate stability of the system. Top rail is made of stainless steel grade 304 with a rectangular cross section. Surface finish will be brush type. Corner joinery section, all joinery made from stainless steel grade 304. Adjustable Pedestal Footing of base diameter 60 mm made from stainless steel grade 316 giving an adjustable height of 100 mm to 150 mm. Surface finish to be lacquer type. Spring loaded butt hinges made from stainless steel grade 304. Surface finish to be matt type. Covers to be lacquer coated. Coat hook with rubber stopper made from stainless steel grade 304. Round Door knob diameter 30 mm with grooves for better hand grip made from stainless steel grade 304.Rotating thumb-turn locking system with privacy indicator made from stainless steel grade 304. Anti-noise rubber padding of thickness 2 mm and width 10 mm
26Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms,
27Centering and shuttering including strutting, propping etc. and removal of form forLintel, beams, plinth beams, girders, bressumers and cantilevers
28CEMENT CONCRETE (CAST-IN-SITU) Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)
29Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
30Steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
31Providing, fixing and commissioning of computer network and UPS wiring on officers table using LEGRAND/ AMP/ TYCO / SYSTIMAXor equivalent as approved by Engineer-in-charge make UTP cat-6 cable from floor rack to officers table with each RJ45 jack terminated by a single cat-6 cable and provision of UPS power supply using 2.5sqmm. Copper wire of finolex/RR kabels/Lapp/Bonton cables make from UPS Distribution board to officers table, provision of epabx wire of 4 pair of finolex/RR kabels/Lapp/Bonton make from officers table to UPS room or where the Epabx shall be located. Each officers table to have 2 RJ 45 jacks and 3 RJ11 jacks with three5 amp. UPS power supply sockets and one switch.All these mentioned points shall be provided using legrand myrius/ schneider opale range of products. The rates quoted for each officers table point shall be complete in all respects including metal boxes,face plates, conduiting, tagging, chiselling, concealing of conduits (above false ceiling, within partitions etc.), cutting of existing flooring etc., termination of computer wiring as per requirements of computer administrator duly certified from a computer network certification company, termination of electrical wiringin UPS distribution board, termination of telephone wiring etc. complete in all respects as approved by Engineer-in-Charge
32Providing, fixing and commissioning of computer network and UPS wiring on staff table using LEGRAND/ AMP/ TYCO / SYSTIMAXor equivalent as approved by Engineer-in-charge make UTP cat-6 cable from floor rack to officers table with each RJ45 jack terminatedby a single cat-6 cable and provision of UPS power supply using 2.5sqmm. Copper wire of finolex/RR kabels/Lapp/Bonton cables make from UPS Distribution board to officers table, provision of epabx wire of 2 pair of finolex/RR kabels/Lapp/Bonton make from officers table to UPS room or where the Epabx shall be located. Each officers table to have 1 RJ 45 jacks and 1 RJ11 jacks with three 5 amp. UPS power supply sockets and one switch.All these mentioned points shall be provided using legrand myrius/ schneider opale range of products. The rates quoted for each officers table point shall be complete in all respects including metal boxes, face plates, conduiting, tagging, chiselling, concealing of conduits (above false ceiling, within partitions etc.), cutting of existing flooring etc., termination of computer wiring as per requirements of computer administrator duly certified from a computer network certification company, termination of electrical wiringin UPS distribution board, termination of telephone wiring etc. complete in all respects. approved by Engineer-in-Charge
33Providing, fixing and termination of computer racks wall mounted of 19" 9U Closed Frame Racks (800 w x 800 d) with following accessories, wall mounted, Front Glass Door Vented (Lockable) & Rear Split Door (Perforated), Fantray with 4 Fans, 2 No. ACDB 5/15 amps 12 Sockets .(APW, Rittal or equivalent as approved by Engineer-in-charge)
34Providing, fixing and termination ofCat 6 EquipmentCord, 4-Pair stranded Unshielded conductors, LSZH Jacket, Transparent plug and boot design provide additional space between adjacent plugs - 3mtr, Color Blue (User & Rack Side)( LEGRAND/ AMP/ TYCO / SYSTIMAXor equivalent as approved by Engineer-in-charge)
35Providing, fixing and termination ofCat 6 EquipmentCord, 4-Pair stranded Unshielded conductors, LSZH Jacket, Transparent plug and boot design provide additional space between adjacent plugs - 1 mtr, Color Blue (User & Rack Side)( LEGRAND/ AMP/ TYCO / SYSTIMAXor equivalent as approved by Engineer-in-charge)
36Providing, fixing and commissioning of computer network using LEGRAND/ AMP/ TYCO / SYSTIMAXor equivalent as approved by Engineer-in-charge make UTP cat-6 cable from floor rack to required location with each RJ45 jack terminatedby a single cat-6 cable . Each loacation to have 1 RJ 45 jacks. The rates quoted for each officers table point shall be complete in all respects including metal boxes, face plates, conduiting, tagging, chiselling, concealing of conduits (above false ceiling, within partitions etc.), cutting of existing flooring etc., termination of computer wiring as per requirements of computer administrator duly certified from a computer network certification company, complete in all respects.
37Providing, fixing and termination of computer racks wall mounted of 42U Closed Frame Racks (800 w x 800 d) with following accessories, Floor Standing, Front Glass Door Vented (Lockable) & Rear Split Door (Perforated), Fantray with 4 Fans, 2 No. ACDB 5/15 amps 12 Sockets & Set of 4 Castor Wheels with Brakes.(APW, Rittal or equivalent as approved by Engineer-in-charge)
38Providing, fixing and installing of linear Led of 1200mm length each with provision for interconnection of fixtures to give a single length fixture of desied length in multiples of 1200mm fixture. each fixture shall be of 20 W+/- 1Wsuitable for connection with Suspended steel wire Mounted 5 Feet length with height adjustment using tool less pinch mechanism having PMMA diffuser with extruded aluminum housing output 2000 lumens ,6500K,P.F.>0.95 with THD<10% ,CRI 80,Surge Protection 2 Kv with IP Protection of IP20 .The LEDswith minium life of 50000The LEDs used in the luminaire shall have CRI of minimum 80. LEDs used must be tested as per EN62471 for Photobiological Safety of humans. The Input voltage range shall be 150V to 270V . Driver Output voltage shall be less than SELV Limits for safe operation and maintenance.Wipro Cat. No LM34-251-XXX-57WCG1/ Tisva Steller LED PL206304 20W 65K 121.5 x 5.4C - 7.3/ Philips : SP781 X LED27S-6500 PSU W6L112 OD SI/ Trilux:LCL H1 1200 OTA 75 LED 3900-840 ET 01 . or LT :C03640PDOOor equivalent as approved by Engineer-in-charge. The rate quoted is inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each series of fixture to be looped in alternate number ( if there are total 8 fixtures in a line then 1,3,5,7 nos will be controlled through 1 switch & 2,4,6,8 will beon another switch) fixtures to be controlled by 1 no. 5 amp. switch. the rates quoted here are inclusive of the wiring and switched etc but since the other fixture shall only be looped deduction of rates as quoted below shall be applicable on the looped fixture approved by Engineer-in-Charge
39Providing, fixing and installing of 18-20W surface Batten LED lighter, 6500K colour temperature, maximum system wattage of 20W , useful life of 50000 Hrs (Complete LM 80 test report for LED should be submitted) , isolated type, multistage Constant Current Constant Voltage topology driver suitable to operate in input voltage range of 150V to 270V ( nominal rated voltage – 240V) with minimum 2KV surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less that 10% should be integral to the luminaire complete with all accessories required with lamps.Wipro Cat. No LL20-281-XXX-65AL1/Tisva RAY SQ PRO LED BATTEN FL1862T5R 18W 65K/ Philips : BN308C LED40S-6500 L120 PSU WH/ Trilux:TRL-X F OTA 4000-857 ETor equivalent as approved by Engineer-in-charge. The rate quoted is for inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch approved by Engineer-in-Charge
40Providing, fixing and installing magnetic track light tracks of Wipro/ Tisva/ Philips/ Triluxor equivalent as approved by Engineer-in-charge for concealed tracks in ceiling which shall be possible to have concealed or surface mounting. The tracks shall consist of raceway for electrical supply to be able move and place the fixture anywhere within the track. The rates quoted are only for the tracks in Rmt excluding the cost of the fixture which are paid seperately. The rates are inclusive of cutting, chiselling, electrical supply inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch. the rates quoted here are inclusive of the wiring and switched etc but since the other fixture shall only be looped deduction of rates as quoted below shall be applicable on the looped fixture. approved by Engineer-in-Charge
41Providing, fixing and installing of 6W track light fixture LED lighter, 6500K colour temperature, to be installed within the track should be integral to the luminaire complete with all accessories required with lamps.Wipro /Tisva CLNTE PRO LED MGTR TKL6291 6W 3K 25D BLK/ Philips / Triluxor equivalent as approved by Engineer-in-charge. The rate quoted is for fixture only the power supply etc is to be drawn from within the track installed approved by Engineer-in-Charge
42Providing, fixing and installing ofled fixture of the same family as mentioned in various wattage. LED Recess Mounted Downlighter Round Shape with minimum system lumen efficacy of 100 lm/W with pressure die cast aluminium housing and P.F.>0.95 with THD<10% ,CRI 80.The LED shall be tested with LM80-08 standard with Useful life of 50000 Hrs at L70. The LEDs used in the luminaire shall have CCT of ANSI Bin 5700 K with CRI of minimum 80. LEDs used must be tested as per EN62471 for Photobiological Safety of humans. The Input voltage range shall be 150V to 270V .Fixture have Surge Protection 2kV .Driver Output voltage shall be less than SELV Limits for safe operation and maintenance.Wipro Cat. No : LD98-131-024-40-XX /Tisva VITO LED PANEL DLP806241 65K DREC/ Philips /Trilux : Ambiella Plus IND G3 LED1275-857 ETor equivalent as approved by Engineer-in-charge. The rate quoted is for inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch if the fixture is looped then a deduction shall be made for each looped fixture approved by Engineer-in-Charge Concealed light Round 7 W
43Providing, fixing and installing ofled fixture of the same family as mentioned in various wattage. LED Recess Mounted Downlighter Round Shape with minimum system lumen efficacy of 100 lm/W with pressure die cast aluminium housing and P.F.>0.95 with THD<10% ,CRI 80.The LED shall be tested with LM80-08 standard with Useful life of 50000 Hrs at L70. The LEDs used in the luminaire shall have CCT of ANSI Bin 5700 K with CRI of minimum 80. LEDs used must be tested as per EN62471 for Photobiological Safety of humans. The Input voltage range shall be 150V to 270V .Fixture have Surge Protection 2kV .Driver Output voltage shall be less than SELV Limits for safe operation and maintenance.Wipro Cat. No : LD98-131-024-40-XX /Tisva VITO LED PANEL DLP806241 65K DREC/ Philips /Trilux : Ambiella Plus IND G3 LED1275-857 ETor equivalent as approved by Engineer-in-charge. The rate quoted is for inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch if the fixture is looped then a deduction shall be made for each looped fixture approved by Engineer-in-Charge. Concealed light Round 10 W
44Providing, fixing and installing ofled fixture of the same family as mentioned in various wattage. LED Recess Mounted Downlighter Round Shape with minimum system lumen efficacy of 100 lm/W with pressure die cast aluminium housing and P.F.>0.95 with THD<10% ,CRI 80.The LED shall be tested with LM80-08 standard with Useful life of 50000 Hrs at L70. The LEDs used in the luminaire shall have CCT of ANSI Bin 5700 K with CRI of minimum 80. LEDs used must be tested as per EN62471 for Photobiological Safety of humans. The Input voltage range shall be 150V to 270V .Fixture have Surge Protection 2kV .Driver Output voltage shall be less than SELV Limits for safe operation and maintenance.Wipro Cat. No : LD98-131-024-40-XX /Tisva VITO LED PANEL DLP806241 65K DREC/ Philips /Trilux : Ambiella Plus IND G3 LED1275-857 ET or equivalent as approved by Engineer-in-charge. The rate quoted is for inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch if the fixture is looped then a deduction shall be made for each looped fixture approved by Engineer-in-Charge. Concealed light Round 12 W
45Providing, fixing and installing ofled fixture of the same family as mentioned in various wattage. LED Recess Mounted Downlighter Round Shape with minimum system lumen efficacy of 100 lm/W with pressure die cast aluminium housing and P.F.>0.95 with THD<10% ,CRI 80.The LED shall be tested with LM80-08 standard with Useful life of 50000 Hrs at L70. The LEDs used in the luminaire shall have CCT of ANSI Bin 5700 K with CRI of minimum 80. LEDs used must be tested as per EN62471 for Photobiological Safety of humans. The Input voltage range shall be 150V to 270V .Fixture have Surge Protection 2kV .Driver Output voltage shall be less than SELV Limits for safe operation and maintenance.Wipro Cat. No : LD98-131-024-40-XX /Tisva VITO LED PANEL DLP806241 65K DREC/ Philips /Trilux : Ambiella Plus IND G3 LED1275-857 ET or equivalent as approved by Engineer-in-charge. The rate quoted is for inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch if the fixture is looped then a deduction shall be made for each looped fixture approved by Engineer-in-Charge. SQUARE CONCEALED LIGHT - 15W
46Providing, fixing and installing of led fixture 20 W +/- 1 WLED Pendent Mounted Downlighter Round Shape with COB havingminimum system lumen efficacy of 80 lm/W with and P.F.>0.95 with THD<20% ,CRI 80.The LED shall be tested with LM80-08 standard with Useful life of 50000 Hrs at L70. LEDs used must be tested as per EN62471 for Photobiological Safety of humans. The Input voltage range shall be 150V to 270V .Fixture have Surge Protection 2kV .Driver Output voltage shall be less than SELV Limits for safe operation and maintenance Wipro Cat. No : LD30-201-36B-40-PS / Tisva / Philips / Triluxor equivalent as approved by Engineer-in-charge. The rate quoted is for inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch if the fixture is looped then a deduction shall be made for each looped fixture approved by Engineer-in-Charge
47Providing, fixing and installing of profile light linear Led light of 50mm visible diffuser width of any desired length made of extruded aluminum housing having PMMA diffuser to give an endless infinite light look of Wipro/ Tisva/ Philips/ Triluxor equivalent as approved by Engineer-in-charge. The fixture shall have a strip light of 20 watts per meter to provide high lumen output in desired colour temperature. the extruded section shall be both recessed mountable or surface mountable, the springs etc for recess mounting shall be suplied with the fixture.The rates quoted are for the entire fixture including the extruded aluminium section, diffuser , drivers & 20 watts/rmt LED strip to be measured in Rmt . The rates are inclusive of cutting, chiselling, electrical supply inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each 1 rmt fixture to be controlled by 1 no. 5 amp. switch. the rates quoted here are inclusive of the wiring and switches etc but since the other fixture shall only be looped deduction of rates as quoted below shall be applicable on the looped fixture approved by Engineer-in-Charge
48Providing, fixing and installing of 18W LED Strip Light Upto 5 Meter roll,from system 2700K colour temperature, maximum system wattage of 18W , useful life of 50000 Hrs (Complete LM 80 test report for LED should be submitted) , isolated type, multistage Constant Current Constant Voltage topology driver suitable to operate in input voltage range of 150V to 270V ( nominal rated voltage – 240V) with minimum 2KV surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less that 10% should be integral to the luminaire complete with all accessories required with lamps.Philips/ Wipro/ Tisva or equivalent as approved by Engineer-in-charge. The rate quoted is for inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch approved by Engineer-in-Charge
49Supply, installation, testing and commissionning of Ceilng fan 900 mm sweep of 5 star BEE rated heavy duty including hanging rod of required length, fixing of fan clamp to ceiling using fasteners making good the damage, any connection, as approved colour etc as required.The rate quoted is inclusive of wiring of 2x1.5 sqmm, modular switch, 2 module step type electronic fan regulator, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch approved by Engineer-in-Charge
50Supply , installation, testing and commissionning of Ceilng fan 1200 mm sweep of 5 star BEE rated heavy dutyincluding hanging rod of required length, fixing of fan clamp to ceiling using fasteners making good the damage, any connection, as approved colour etc as required.The rate quoted is inclusive of wiring of 2x1.5 sqmm, modular switch, 2 module step type electronic fan regulator, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch approved by Engineer-in-Charge
51Deduction in amount foreach fixture that is looped in nos. or each Rmt (The quoted amount for this Item shall be Deducted from total quoted amount of the Bidder)
52Supply , installation, testing and commissionning of exhaust fan 300 mm sweep, 900 rpm heavy duty in existing opening including making good the damage connection, as approved colour etc as required.The rate quoted is for inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture. Each fixtures to be controlled by 1 no. 5 amp. switch approved by Engineer-in-Charge
53Supply , installation, testing and commissioningof twin control light point with 1.5 sq.mm HFFR PVC insulated copper conductor single core cable in surface/ recessed conduit, 2 way switch and earthing the point with 1.5 sqmmHFFR PVC insulated copper conductor single core cable etc. as required. The rate quoted is for inclusive of wiring of 2x1.5 sqmm, modular switch, modular plate, modular box etc all complete fittings for switching on and off of the fixture.
54Wiring for circuit/submain wiring along with earth wire with the following sizes of HFFR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required from Distribution board to the first switchboard. 2X2.5 sqmm. + 1X1 sqmm earth wire
55Wiring for circuit/submain wiring along with earth wire with the following sizes of HFFR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required from Distribution board to the first switchboard.2X4 sqmm. + 1X4 sqmm earth wire
56Supplying and fixing following modular switch/ sockets of legrand myrius/ schneider opale/ panasonic vision range complete in all respects with face plates etcon the existing modular plate & switch box including connectionsas required 15/16 amps switch
57Supplying and fixing following modular switch/ sockets of legrand myrius/ schneider opale/ panasonic vision range complete in all respects with face plates etcon the existing modular plate & switch box including connectionsas required 6 pin 15/16 amps socket outlet & switch for raw power
58Supplying and fixing following modular switch/ sockets of legrand myrius/ schneider opale/ panasonic vision range complete in all respects with face plates etcon the existing modular plate & switch box including connectionsas required Bell Push
59Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.
60Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
61Supplying and fixing following way TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly wired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator).Hager/ Legrend/ Panasonic /Schenider or equivalent as approved by Engineer-in-charge. 4 way (4 + 12),Double Door
62Supplying and fixing following way TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly wired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator).Hager/ Legrend/ Panasonic /Schenideror equivalent as approved by Engineer-in-charge. 6 way (4 + 18),Double Door
63Supplying and fixing following way TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly wired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator).Hager/ Legrend/ Panasonic /Schenider or equivalent as approved by Engineer-in-charge. 12 way (4 + 36),Double Door
64Supplying and fixing following way pre-wired Vertical DB with incomer MCCB of desired rating with TPN outgoing for feeding the other floordistribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly wired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (with 4pole RCCB). 1( MCCB 100A)+ 6 way(4 Nos RCCB 63A) for UPS supply Distribution
65Supplying and fixing following way pre-wired Vertical DB with incomer MCCB of desired rating with TPN outgoing for feeding the other floordistribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly wired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (with 4pole RCCB). 1( MCCB 200A)+ 6 way (6 Nos RCCB 63A) for UPS Server Room
66Supplying and fixing following way pre-wired Vertical DB with incomer MCCB of desired rating with TPN outgoing for feeding the other floordistribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly wired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (with 4pole RCCB). 1( MCCB 100A)+ 6 way (4Nos RCCB) for electrical supply Distribution
67Supplying and fixing following rating, four pole, 415 volts, RCCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps
68S/F DP MCB isolator : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps
69Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.. Hager, Legrend & Schenider. Single Pole
70Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.. Hager, Legrend & Schenider. Double Pole
71Supplying and fixing of conduit box for receiving incoming/outgoing wires for existing TPN/SPN distribution board facricated of 1.2 mm thick steel sheet for 415 volts on surface/ recess complete etc. as required.
72Supply of following sizes of XLPE insulated PVC sheathed, Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 amended upto date. 3.5 C x 400 sq.mm
73Supply of following sizes of XLPE insulated PVC sheathed, Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 amended upto date. 3..5 C x 240 sq.mm
74Supply of following sizes of XLPE insulated PVC sheathed, Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 amended upto date.3.5 C x 35 sq.mm
75Supply of following sizes of XLPE insulated PVC sheathed, copper conductor armoured power cable of 1.1 KV grade conforming to IS 7098 amended upto date. 4 C x 6 sq.mm
76Supply of following sizes of XLPE insulated PVC sheathed, copper conductor armoured power cable of 1.1 KV grade conforming to IS 7098 amended upto date. 4 C x 10 sq.mm
77Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated PVC sheathed/XLPE aluminium conducter cable of 1.1 kV grade as required.3..5 C x 400 sq.mm
78Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated PVC sheathed/XLPE aluminium conducter cable of 1.1 kV grade as required.3..5 C x 240 sq.mm
79Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated PVC sheathed/XLPE aluminium conducter cable of 1.1 kV grade as required.3.5 C x 35 sq.mm
80Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 kV grade of the following size on cable tray as required. Upto 35 sqmm (clamped with 1mm thick saddle box)
81Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 kV grade of the following size on cable tray as required. Above185 sqmm and upto 400 sqmm (clamped with 40X3 mm thick MS flat clamp)
82Supplying and making end termination with brass compression gland and copperlugs for following size of PVC insulated PVC sheathed/XLPE copper conducter cable of 1.1 kV grade as required.4 C x 6 sq.mm
83Supplying and making end termination with brass compression gland and copperlugs for following size of PVC insulated PVC sheathed/XLPE copper conducter cable of 1.1 kV grade as required. 4 C x 10 sq.mm
84Supply and installation following size of perforated pre paintied M.S. Cable tray with perforation not more than 17.5%, in convin sections, jointed with connectors, bends, reducers, Tees or any other accesorry required t for end to end hanging of cable trays in any direction suspended from the ceiling with MS suspenders including bolts & nuts, painting suspenders etc as required.300 mm width 75 mm thick x 2 mm thick
85Supply and installation following size of perforated pre paintied M.S. Cable tray with perforation not more than 17.5%, in convin sections, jointed with connectors, bends, reducers, Tees or any other accesorry required t for end to end hanging of cable trays in any direction suspended from the ceiling with MS suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width 50 mm thick x 1.6 mm thick
86Supply, installation, testing and commissioning of indoor UL/FCC Listed colour dome IP camera,1/3"" CMOS sensor,2 Megapixel, varifocal 2.8-10 mm lens, Auto Iris, Day Night cameras(0.1 Lux ) including integrated IP 56,Tamper proof & Motion detection, complete with Dome Housing, Connectors, Lens, Camera Mounts, Power Supply and all Ancillary Equipment & all accessories.(Make Bosch/ Samsung/ Hikvisionor equivalent as approved by Engineer-in-charge)
87Supply, installation, testing and commissioning of indoor UL/FCC Listed colour Box type IP camera,1/3"" CMOS sensor, 2MP, varifocal 3-12 mm lens , Auto Iris, Day Night cameras with ICR (0.1 lux ) including integrated IP 56,Tamper proof & Motion detection, complete with box Housing, Connectors, Lens, Camera Mounts, Power Supply and all Ancillary Equipment & all accessories. (Make Bosch/ Samsung/ Hikvisionor equivalent as approved by Engineer-in-charge)
88Supply, Installation, Testing and Commissioning of 32Channel Network Video Recorder forrecording real timeaudio & video and data applications , inbuilt storage, redundant Fans & Power Supplies. The NVR should store all cameras at 4CIF resolution at H.264 compression forminimum 30 days backup@18 FPS, or min 6 TB harddisk capacity, should have built in DVD writer orUSB for video archival, 2 monitor outputs,LAN connectivity etc. Please note the NVR should comply to EN, FCC, UL standards. The system requirement are mentioned in the specifications. The NVR should be networkable via IP protocol & should be able to connect to a web based system for remote viewing via web system(Make Bosch/ Samsung/ Hikvisionor equivalent as approved by Engineer-in-charge)
89Providing , supplying & installing stackable 24 port POE switch of 10/100/1000 Mbps 24 ports & 4 Uplink ports 24 Port layer 2+ stackablePOE switch enterprise series with 24*1G Copper ports, 4* SFP+ (10G Ports) loaded with SFP modules of make Cisco/ Linksys / Avaya including installation termination mounting etc complete in all respects
90Supply, installation, testing and commissioning of 19" 6 U Presidential equipment rack of required size made out of CRCA sheet steel duly powder quoted & provided with P.V.C channel to house all the control equipment"s, amplifiers with wiring & switches complete in all respect.rates quoted are inclusive of 24 port patch panel of Legrand/ AMP/ Tyco makeor equivalent as approved by Engineer-in-chargecomplete in all respects including 1 mtr patch cables of same make, terminated and complete
91Providing & laying in place cat-6 cable in conduits complete with bends, flexible pipe, RJ45 connectors etc . Including termination. (Legrand/ Amp/ Digilinkor equivalent as approved by Engineer-in-charge)
92Supply, installation, testing & commissioning of the following Sensors: Movement / Presence detector with 360* angle & having area of coverage 6 mtr diameter suitable for controlling florescent / halogen / LED light fitting upto 4 mtr height. It should have 2 no NO/ & NC potential free contact or attached relay for the same to control luights, fans, HVAC etc, Lux setting 5-1000 Lux or more and time delay 5-15 min or more. Model No. EE810Make Hager/ Schneider/ Legrandor equivalent as approved by Engineer-in-charge
93Supply, installation, testing & commissioning of the following Sensors: 2 Core 1.5 Sqmm, FR PVC Insulated armoured cable, PVC Sheathedconductor multistranded, twistedcable, for signal.(Make Finolex/ Lapp/ RR/ Bontonor equivalent as approved by Engineer-in-charge)
94Providing & fixing of white vitreous China wall mounting cascade type water closet (American Standard Cat No. TF-3128 / Kohler Cat No. K-18131X-O / Queo cat. no. 207240210 / Roca Cat No. - RS34630346S ) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required with chrome finished brass concealed type dual flush cistern (Roca/ Jaquar / Grohe/ Kohleror equivalent as approved by Engineer-in-charge)comprising of actuator button facia assembly including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-Incharge. the concealed cistern shall be completly repairable from the front facia plates without any damage and withoutremoval of cistern from inside the wall.The water discharge shall be as per GRIHA norms or better.
95Providing and fixing first quality white vitreous china, Oval shaped undercounter Wash Basin of Hindware(10045)/ Kohler (K-2075IN)/Queo(177160110) / Roca (RS327114460)with M.S. or CI brackets,32mm dia C.P. brass Bottle Trap (Jaquar / Roca (RF9065A1)/ Kohler/Queo), CP waste (Jaquar / Roca/ Kohler/Queo) and other ancillary fittings including painting of fitting as per direction of engineer.
96Providing and fixing white glazed vitreous china urinal of / kohler /american standards/Queo(257610210) /Rocaor equivalent as approved by Engineer-in-chargeincluding C.I. hangers, CP brass/stainless steel spreader, 32 mm CP brass domical waste/ stainless steel jali to prevent napthelene balls from getting flushed, 40 mm CP brass bottle trap and pipe to wall with CP flange with AC operated automatic concealed urinal flushing system with installation box for total repairability from front of Queo/kohler/Roca/ Grohe make with electric wiring from sensor to solonoid valve for individual urinals, to ensure flushing only when in use, with pre flushing feature, comprising of all plumbing, electronic items including infrared sensors for full functioning of the automatic sensor and urinal complete. The entire piping including spreaders, pipes from sensor to urinal etc shall be completly concealed.The water discharge shall be as per GRIHA norms or better.
97Providing and fixing of C.P. Pillar Cock with auto closing system for wash basin of (Jaquar/ Grohe / Roca- Tarim / Kohler- eolia/Queo)or equivalent as approved by Engineer-in-chargewater discharge rate as per griha norms without pop upwaste system with 450 mm long braided hoses complete including cutting and making good the walls wherever required.
98Providing and fixing lavatory mounted Stainless steel minimum 304 grade liquid Soap Dispenserof jaquar/ Roca / kohleror equivalent as approved by Engineer-in-charge with brass lid & brackets fixed with fastners and S/Sscrews complete as per directions of Engineer incharge.
99Providing and fixing of 15mm dia C.P. brass angle valve (Grohe / Roca(RF525164500) / Kohler/Queo(Q503192220) or equivalent as approved by Engineer-in-charge with C.P. brass wall flange etc. completeincludingcutting and making good the walls wherever required as per direction of Engineer-Incharge.
100Providing & fixing for handicapped toiletAdjustable type wash basin complete with all accessories e.i. brackets (Model R4140), waste pipes complete in all respect and as required (Make : Presalit - Commander/ hindware/ kohler/Roca/Groheor equivalent as approved by Engineer-in-charge) and other accessories complete as required as per direction of Engineer-Incharge.
101Providing & fixingfor handicapped toilet 2 Nos support arms and bracket to mounted on the track (vertically) model R3148, 2 Nos for ea ch water closet complete as required (Make : Presalit-Commander/ hindware/ kohler/Roca/Groheor equivalent as approved by Engineer-in-charge) as per directions of Engineer-Incharge.
102Providing & fixingfor handicapped toilet of Raised Toilet seat with cover complete in all respect (Make: Presalit- Commander/ hindware/ kohler/Roca/Groheor equivalent as approved by Engineer-in-charge) as required as per directions of Engineer-Incharge.
103Providing and fixing stainless steel twin coat hook fixed with CP brass screws. (Grohe / Roca / Kohler/Queo(Q253196120or equivalent as approved by Engineer-in-charge) as per direction of Engineer in Charge.
104Providing and fixing fully automatic "NO TOUCH" die cast aluminium, epoxy coated hand drier of Roca/ jaquar/ kohler/ groheor equivalent as approved by Engineer-in-charge make suitable to operate on 220 volts, single phase 50 hz motor rating 100W, 2850 rpm automatic infrared sensing device, 1600W heating element approximate 275 cum/hr air flow wind velocity 15.5 m/sec. AC power supply.
105Providing & Fixing of C.P brass hand spray (health faucet) of Grohe / Roca (RF9060A1)/ Kohler/ Queo(Q503192520)or equivalent as approved by Engineer-in-charge water discharge rate as per griha norms with push button control and flexible hose connection with C.P. holder for hand spray complete including CP brass T extension for connection from angle valve complete in all respects. and making good, as required as per direction of Engineer in Charge.
106Providing & fixing G.I pipe complete with G.I. fittings & clamps including trenching and refilling etc.(External Work) 65mm dia nominal bore
107painting G I pipes and fittings with 2 coats of anti corrosive bitumastic paint of approved quality 65mm dia nominal bore
108Providing & fixing G.IUnion in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) 65 mm dia nominal bore
109Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end 65 mm nominal bore) 65mm dia nominal bore
110Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work - exposed on wall) 20mm dia nominal bore
111Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work - exposed on wall) 25mm dia nominal bore
112Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work - exposed on wall) 32 mm dia nominal bore
113Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm dia nominal bore
114Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm dia nominal bore
115Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm dia nominal bore
116Providing & fixing in position polypropylene quarter turn gate valveswith metal ball, handle, washer, of following sizes including providing necessary fittings and proper connections. 25mm dia nominal bore
117Providing & fixing in position polypropylene quarter turn gate valveswith metal ball, handle, washer, of following sizes including providing necessary fittings and proper connections. 63mm dia nominal bore
118Constructing masonry chamber 60x60x75cm inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for valves with C.I. surface box 100mm top dia , 160mm bottom dia & 180mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 2 coarse sand) 12mm thick finished with a floating coat of heat cementcomplete as per standard design. With F.P.S. bricks
119Providing, fixing, jointing and testing UPVC soil, waste, vent pipework comprising UPVC pipe conforming to IS :4985-1983 and of required class as specified below and fittings (moulded as well as fabricated) like elbows, bends, reducers, threaded tail pieces, caps, suitable elbow with suitable extension piece for drain point and other specials jointing with cement solvent, chasing, cutting and making good the walls & floors, pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation. 40 mm dia 6 kg/cm2 (Class III )
120Providing, fixing, jointing and testing UPVC soil, waste, vent pipework comprising UPVC pipe conforming to IS :4985-1983 and of required class as specified below and fittings (moulded as well as fabricated) like elbows, bends, reducers, threaded tail pieces, caps, suitable elbow with suitable extension piece for drain point and other specials jointing with cement solvent, chasing, cutting and making good the walls & floors, pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation. 50 mm dia 6 kg/cm2 (Class III )
121Fixing, testing & commissioning of floor Drain flat model with Sealing flange,with removable trap (Storage water height-Seal- 30mm) (Drain Capacity 0,6 l/s) withheight adjustable and Rotatabletop 100 X 100mm and Stainless Steel grate 94x94mm,with protection plug, with plastic frame and Stainless Steel Grate.Loading capacity class K=300kg, with supply DN40, with horizontal drain socket, adjustable due to ball joint with outlet 50 mm.With Height Adjustment Piece Model No.:-4947 Article Code:- 111496(Body made of environmentally friendly PP (poly propylene). Item to include all required core cutting, chasing, cutting and making good the floors, complete in all respects.
122Providing, of floor DrainFlat model with Sealing flange,with removable trap (Storage water height-Seal- 30mm) (Drain Capacity 0,6 l/s) withheight adjustable and Rotatabletop 100 X 100mm and Stainless Steel grate 94x94mm,with protection plug, with plastic frame and Stainless Steel Grate.Loading capacity class K=300kg, with supply DN40, with horizontal drain socket, adjustable due to ball joint with outlet 50 mm.With Height Adjustment Piece Model No.:-4947 Article Code:- 111496(Body made of environmentally friendly PP (poly propylene)
123Fixing, testing & commissioning of floor trap with Sealing flange,with removable trap,(Storage Water Height 50 mm-Water Seal),with protection plug, with Three rotable supply DN50, with horizontal drain socket,with outlet 70/ 100 mm. WITHheight adjustable and rotratable TOP FRAME (Height adjustment piece) 150x 150 (suitable for 143x143 GRATE) WITH BACK PRESSURE SEAL.WITH STAINLESS STEEL GRATE(143x143).With Height Adjustment Piece Model No.:-4996 Article Code:- 112707 LOADING CAPACITY CLASS K=300KG Quality controlled in accordance withDIN EN -1253(Body and Top Framemade of environmentall friendly PP (poly propylene).Item to include all required core cutting, chasing, cutting and making good the floors, complete in all respects.
124Providing of floor trap with Sealing flange,with removable trap,(Storage Water Height 50 mm-Water Seal),with protection plug, with Three rotable supply DN50, with horizontal drain socket,with outlet 70/ 100 mm. WITHheight adjustable and rotratable TOP FRAME (Height adjustment piece) 150x 150 (suitable for 143x143 GRATE) WITH BACK PRESSURE SEAL.WITH STAINLESS STEEL GRATE(143x143).With Height Adjustment Piece Model No.:-4996 Article Code:- 112707 LOADING CAPACITY CLASS K=300KG Quality controlled in accordance withDIN EN -1253(Body and Top Framemade of environmentall friendly PP (poly propylene)
125Supplying &fixing full way lever operated forged brass ball valve of brass body with forged brass hard chromeplated steel ball tested to a pressure not less than 15 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers union etc. as per direction of Engineer in Charge. 32 mm nominal outer dia Pipes
126Providing & fixing PN 16 butterfly valve including rubber gasket, flanges, nuts, bolts, washers & painting complete as required as per direction of Engineer in Charge. 65 mm dia
127Supply Installation and Commissioning of UL Listed and FM approved, 10th edition 32 bit Fire alarm control panel having microprocessor based 8 loop cards expandable upto 10 loops with 252 intelligent points per loop cards in any flexible combination (detectors/ devices) . The panel have 6 inch long LCD touch screen and LED"s for displaying system status. The panel shall support degrade mode operation. The panel shall have the capacity of storing upto 5000 events. The panel shall have Multiple levels of password protection, Automatic environmentalbe compensation for smoke detectors, Degrade-mode operation, polarity-insensitive detection circuits, Supports single-person Walk Test, Connectivity to a leased-line / city-tie module, Battery charger shall be able to charge the system batteries upto 100 AH. The panel shall have 240 V AC power supply, 24 V SMF batteries sufficient for 24 hour in standby and 30 minutes in alarm complete as per specification. The Panel shall have the capacity of connecting additional 15 panels or Network terminals, with redundancy in the network. The panel shall have the capacity of connecting maximum 8 Remote terminals or 8 remote displays. The panel shall be approved by UL 864 9th Edition Listed, ULC, FM, CSFM & NYC Fire Department complete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ XLS3000 or equivalent as approved by Engineer-in-charge Main Fire Alarm Control Panel 4 Loop
128Supply Installation and Commissioning of UL Listed and FM approvedrepeater PanelThe panel shall be able to givelocation ofall fire and fault and Isolation conditions of addressable units of main Fire Alarm panel via the address codes and also having remote-system-control capabilities. The panel shall have a2”x4-3/4” backlit LCD screen. Panel will show all details of above panelscomplete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ XLS3000or equivalent as approved by Engineer-in-charge
129Supply Installation and Commissioning of UL listed and FM approvedIntelligent Addressable Multicriteria Smoke detectorhaving responsiveness of photoelectric, thermal (Rate-of-Rise and Fixed), ionization technology and false alarm resistance along with standard base. The detector shall be Polarity insensitive, dust-resistant photoelectric chamber, Automatic environment compensation, field programmable as rate-of-rise or fixed temperature. The detector shall have Tri-color detector-status light-emitting diode (LED) with 360° view. The detector shall be approved by UL, ULC, FM, CSFM & NYC Fire Department.complete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ ESMI/ XLS3000or equivalent as approved by Engineer-in-charge
130Supply Installation and Commissioning of UL listed and FM approvedIntelligent Addressable Heat detectorhaving responsiveness ofthermal (Rate-of-Rise and Fixed), ionization technology and false alarm resistance along with standard base. The detector shall be Polarity insensitive, Automatic environment compensation, field programmable as rate-of-rise or fixed temperature. The detector shall have Tri-color detector-status light-emitting diode (LED) with 360° view. The detector shall be approved by UL, ULC, FM, CSFM & NYC Fire Department complete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ XLS3000or equivalent as approved by Engineer-in-charge
131Supply Installation and Commissioning of UL listed and FM approved single action Manual Pull Station. MCP Shall be Polarity insensitive, shock and vibration resistant, inbuilt isolator. MCP shall be approved by UL, ULC, FM, CSFM & NYC Fire Departmentcomplete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ XLS3000or equivalent as approved by Engineer-in-charge
132Supply Installation and Commissioning of UL listed and FM approved Intelligent addressable Output with one input module having facility to activate sounders, AHU Trippings etc. Module Shall be Polarity insensitive, inbuilt isolator approved by UL, ULC, FM, CSFM & NYC Fire Department complete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ XLS3000or equivalent as approved by Engineer-in-charge
133Supply Installation and Commissioning of UL and FM listed Conventional Sounder of 87 dBA minimum sound, It shall be of same brand (Make) as that of main fire alarm panelcomplete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ XLS3000or equivalent as approved by Engineer-in-charge
134Supply Installation and Commissioning of UL listed and FM approved Intelligent addressable one input module having facility to integrate water flow switch etc. Module Shall be Polarity insensitive, inbuilt isolator approved by UL, ULC, FM, CSFM & NYC Fire Departmentcomplete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ XLS3000or equivalent as approved by Engineer-in-charge
135Supply Installation and Commissioning of 2 KVA UPS on line with 30 min backup. Make: Uniline/ APC/ Amersonor equivalent as approved by Engineer-in-charge
136Supply,installation,testing and commissioning 8 Zone EVAC Controller, built-in 500W class-D amplifier, built-in EVAC and alert voice message by SD card, with fireman microphone, with AB speaker line low impedance supervision, with amplifier auto changeover into standby when fault, with extension amplifier connector, AC and DC battery operation entire satisfaction of Engineer In Charge. Make: BOSE/JBL/ AYZO/ WONTELor equivalent as approved by Engineer-in-charge
137Supply,installation,testing and commissioning of Remote Paging Microphone, 12 zone capacity with 12 keypad buttons, each system can connection up to 32 remote microphone, DC24V power supply. Make: BOSE/JBL/ AYZO/ WONTELor equivalent as approved by Engineer-in-charge
138Supply,installation,testing and commissioning of Table mount Touch screen paging station/ announcement console for selection of zones, supervision of system status, setting of scheduled broadcasts with the following functions: Built-in monitoring loudspeaker, Detachable goose-neck microphone, LCD touchscreen display, Audio input, Make: BOSE/JBL/ AYZO/ WONTELor equivalent as approved by Engineer-in-charge
139Supply, installation, testing & commissioning of Booster Amplifier capable of delivering 480 Wattage RMS power output for speakers, built-in fan for temperature control, built in line matching transformer distortion typically < 3% @1 KHz, S/N> 80 dB complete as required. Make: BOSE/JBL/ AYZO/ WONTELor equivalent as approved by Engineer-in-charge
140Supply,Installation,Testing & Commissioning of 4" 6W Ceiling Speaker with SPL at rated power/1W 90dB (1m & 1kHz). Frequency response of 125Hz – 16kHz (-10 dB with reference to 1kHz). The speaker should have tappings at 6W/3W/1.5W." Make: BOSE/JBL/ AYZO/ WONTELor equivalent as approved by Engineer-in-charge
141Supply, Installation, Testing & Commissioning of 6W Wall mount with max SPL 1M/6W 96dB . Frequency response of 110 Hz ~13K Hz. The speaker shoud have tappings at 6W/3W Make: BOSE/JBL/ AYZO/ WONTELor equivalent as approved by Engineer-in-charge
142Supply Installation and Commissioning of 2 way Talk back system with inbuilt mic and speakercomplete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ ESMI/GST/ XLS3000/ WONTELor equivalent as approved by Engineer-in-charge
143Supply Installation and Commissioning of control panel of talk back system with telephone handset complete the work upto the entire satisfaction of Engineer In Charge. Make: Cerberus by Siemens / Autronic/ ESMI/GST/ XLS3000/ WONTELor equivalent as approved by Engineer-in-charge
144Supply Installation and Commissioning of 19" Presidential equipment rack of required size made out of CRCA sheet steel duly powder quoted & provided with PVC channel to house all the control equipments, amplifiers with wiring & switches complete in all respectcomplete the work upto the entire satisfaction of Engineer In Charge. Make: Comrack/DLink EMERGENCY EXIT LIGHTING SYSTEM - FULLY COMPLIANT WITH NFPA 101 ( Central battery system)or equivalent as approved by Engineer-in-charge
145Supply, installation, testing & Commissioning of CENTRAL BATTERY SYSTEM PANEL Emergency System Panel with Liquid Crystal Display (LCD) for the simultaneous display of the system status and fault.128 x 64 pixel graphic display,backlit, contrast andbrightness adjustable The control module must have following features:Monitor and control all test cycles and functions.three function keys, freely assignable,With volt free contacts for internal fault, battery mode operation & external fault, The emergency supply panel shall supervise the battery status such as Battery Over voltage / Battery Under voltage. Charging failure shall be indicated as an Internal fault by an indicator LED and potential free relay contact, As per global standard 20 lights per circuit, 4 Circuit with battery backup, The batteries shall be maintenance free VRLA sealed lead acid gas recombination type with a minimum design life of 10 years at prevailing ambient temperature,They shall have extremely low gas generation, low self-discharge and have permanently sealed pressure release vents, The batteries shall be sized to power complete system for 3 Hours following mains failure at 100% light output of all emergency lamps, The unit shall be fitted with a deep discharge protection circuit, which has two operation phases: When in battery mode the battery voltage decreases to 195V, a preliminary deep discharge alarm shall be given. When the battery voltage decreases to 175V, the load shall be disconnected. The circuit shall allow the battery to increase its voltage without switching the load ON again, thus avoiding detrimental full discharge. The panel shall automatically return to normal operation, once the mains supply recovers, Fully compliant with requirements of designed and installed to meet the fire and safety code of practice & the respective system designed in compliance with EN60950, EN 50272-2 standards EN Standards Makes: EATON / WONTEL / ABBor equivalent as approved by Engineer-in-charge
146Supply Installation and Commissioning of LPCB Certified 2c x 1.5 sq.mm fire survival Circuit Integrity (CI) armoured cable, 600/1000 volts with class-2 Copper conductor having halogen free ceramified silicon insulation as per BS EN 50363 and low smoke zero halogen (LSZH) inner & outer sheath. Should comply to EN 61034-2 & EN 60754-1. The cable should meet fire performance circuit integrity test as per BS EN 50200 & BS 6387 CWZ (950 Deg. C for 3 hrs).” Outer sheath in RED complete the work upto the entire satisfaction of Engineer In Charge. Make: Polycab/ FRTK/ Bontonor equivalent as approved by Engineer-in-charge
147FIRE HYDRANT / SPRINKLER SYSTEM SUPPLY, INSTALLATION , TESTING & COMMISSIONING OF:- Supply of Single headed, gun-metal /S.S isi marked oblique pattern hydrant landing valve with 80 mm dia. flanged inlet and 63 mm dia. instantaneous typefemale outlet complete with gun-metal cap.andg.i. chain, twist release type lug and all accessories as per is:5290-1983(type `a").(make:Newage /Omaxe / Ataseeor equivalent as approved by Engineer-in-charge)
148SUPPLY, INSTALLATION , TESTING & COMMISSIONING OFSupply of First-aid fire hose reel wall mounting swinging type completewith drum, bracket, 25 mm dia. stop valve and 20 mm dia. x 30 m long high pressure hose reel tubing as per is:444 with gun-metal shut-off nozzle having 5 mm dia. orifice.the hose reel shall strictly as per IS: 884 : 1985. (make: FGE /omex/ Ataseeor equivalent as approved by Engineer-in-charge)
149SUPPLY, INSTALLATION , TESTING & COMMISSIONING OF Supply of Non-percolating flexible hose (RRL type - `A") isi marked (is:636) 63 mm dia. x 15 m long complete with instantaneous type gun-metal /s.s 63 mm dia. isi marked male and female couplings (IS:903) bound and riveted to hose pipe with copper rivets and 1.5 mm dia. copper wire. (make: newage /Omaxe/Ataseeor equivalent as approved by Engineer-in-charge)
150SUPPLY, INSTALLATION , TESTING & COMMISSIONING OFSupply of Gun-metal /s.s 63 mm dia. short branch pipes with 16 mm dia. nozzles, isi marked (IS:903).(make: newage /Omaxe / Ataseeor equivalent as approved by Engineer-in-charge)
151SUPPLY, INSTALLATION , TESTING & COMMISSIONING OF Supply of Indoor type hose cabinet hose cabinets fabricated from 18 g M.S sheet with full glass door and locking arrangement, suitable to accommodate 2 nos. 15 m long hoses and 1-no. branch pipe.the cabinet shall be painted with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade and shall be suitably mounted on a raised masonry platform as required. exact size & shape shall be as per site conditions and prior approval. (make: cabone /Omaxe/ Ataseeor equivalent as approved by Engineer-in-charge)
152SUPPLY, INSTALLATION , TESTING & COMMISSIONING OF Supply of Gun-metal /S.S fire brigade connection (suction collecting head) consisting of 4 nos. 63 mm dia. instantaneous type male coupling with built-in check valves and 100 mmdia. flanged outlet complete with bolts, nuts and rubber insertions as required as per is: 904-1983.(make: newage /Omaxe /Ataseeor equivalent as approved by Engineer-in-charge)
153SUPPLY, INSTALLATION , TESTING & COMMISSIONING OFAir cushion tank (air vessel) 200 mm dia. x 1200 m high with dished top, made of minimum 6 mm thick m.s. pipe/plate complete with 20/25 mm dia. brass air valve (ball type), and all accessories as required including fixing bracketsor equivalent as approved by Engineer-in-charge.
154SUPPLY, INSTALLATION, TESTING & COMMISSIONING OFSupply of Mild steel black pipe (IS:1239 part-i) Heavy class including cutting, screwing, welding etc. complete with drop forged steel / butt welded fittings viz. tees, bends, elbows, flanges, reducers, clamps hangers etc. including cutting holes and chases in brick or rcc walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade. ( make: tata/ jindal/ parkash surya) 200 mm dia or equivalent as approved by Engineer-in-charge
155SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF Supply of Mild steel black pipe (IS:1239 part-i) Heavy class including cutting, screwing, welding etc. complete with drop forged steel / butt welded fittings viz. tees, bends, elbows, flanges, reducers, clamps hangers etc. including cutting holes and chases in brick or rcc walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade. ( make: tata/ jindal/ parkash suryaor equivalent as approved by Engineer-in-charge)150 mm dia
156SUPPLY, INSTALLATION , TESTING & COMMISSIONING OFSupply of Mild steel black pipe (IS:1239 part-i) Heavy class including cutting, screwing, welding etc. complete with drop forged steel / butt welded fittings viz. tees, bends, elbows, flanges, reducers, clamps hangers etc. including cutting holes and chases in brick or rcc walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade ( make: tata/ jindal/ parkash suryaor equivalent as approved by Engineer-in-charge) 100 mm dia
157SUPPLY, INSTALLATION , TESTING & COMMISSIONING OFSupply of Mild steel black pipe (IS:1239 part-i) Heavy class including cutting, screwing, welding etc. complete with drop forged steel / butt welded fittings viz. tees, bends, elbows, flanges, reducers, clamps hangers etc. including cutting holes and chases in brick or rcc walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade. ( make: tata/ jindal/ parkash suryaor equivalent as approved by Engineer-in-charge) 80 mm dia
158SUPPLY, INSTALLATION , TESTING & COMMISSIONING OFSupply of Mild steel black pipe (IS:1239 part-i) Heavy class including cutting, screwing, welding etc. complete with drop forged steel / butt welded fittings viz. tees, bends, elbows, flanges, reducers, clamps hangers etc. including cutting holes and chases in brick or rcc walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade. ( make: tata/ jindal/ parkash suryaor equivalent as approved by Engineer-in-charge) 65 mm dia
159SUPPLY, INSTALLATION , TESTING & COMMISSIONING OFSupply of Mild steel black pipe (IS:1239 part-i) Heavy class including cutting, screwing, welding etc. complete with drop forged steel / butt welded fittings viz. tees, bends, elbows, flanges, reducers, clamps hangers etc. including cutting holes and chases in brick or rcc walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade. ( make: tata/ jindal/ parkash suryaor equivalent as approved by Engineer-in-charge) 50 mm dia
160SUPPLY, INSTALLATION , TESTING & COMMISSIONING OFSupply of Mild steel black pipe (IS:1239 part-i) Heavy class including cutting, screwing, welding etc. complete with drop forged steel / butt welded fittings viz. tees, bends, elbows, flanges, reducers, clamps hangers etc. including cutting holes and chases in brick or rcc walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade. ( make: tata/ jindal/ parkash suryaor equivalent as approved by Engineer-in-charge) 32 mm dia
161SUPPLY, INSTALLATION , TESTING & COMMISSIONING OF Supply of Mild steel black pipe (IS:1239 part-i) Heavy class including cutting, screwing, welding etc. complete with drop forged steel / butt welded fittings viz. tees, bends, elbows, flanges, reducers, clamps hangers etc. including cutting holes and chases in brick or rcc walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade. ( make: tata/ jindal/ parkash suryaor equivalent as approved by Engineer-in-charge)25 mm dia
162Supplying, installing, testing and commissioning of hydraulically operated Sprinkler control valve, with water motor gong bell and trims as required, pressure gauges, drain valves, isolation valves, check valves, strainers etc. complete. Alarm valve shall be UL listed & FM approved.150MM DIA(Omaxe/Tyco/HDor equivalent as approved by Engineer-in-charge
163Supply of Mild steel black pipe (IS:1239 part-i) Heavy class under ground pipe including cutting, screwing, welding etc. complete with drop forged steel / butt welded fittings viz. tees, bends, elbows, flanges, reducers, clamps hangers etc. including cutting holes and chases in brick or rcc walls/slabs and making good the same complete including 4 mm thick raping coating , diggingof soil and fillinnf the same after the paying of pipe. ( make: tata/ jindal/ parkash suryaor equivalent as approved by Engineer-in-charge) 150mm dia
164Supply of Cast ironslim seal wafer type non-return valves complete with matching flanges, rubber insertion, nuts, bolts & washers etc. complete (pn 1.6) of following sizes : ( make: Kartar/castle/NVRor equivalent as approved by Engineer-in-charge)150mm dia
165Supply of Cast ironslim seal wafer type non-return valves complete with matching flanges, rubber insertion, nuts, bolts & washers etc. complete (pn 1.6) of following sizes : ( make: Kartar/castle/NVRor equivalent as approved by Engineer-in-charge) 80mm dia
166Supply of Cast ironslim seal wafer type non-return valves complete with matching flanges, rubber insertion, nuts, bolts & washers etc. complete (pn 1.6) of following sizes : ( make: Kartar/castle/NVRor equivalent as approved by Engineer-in-charge)100mm dia
167Supply of Cast iron gear/hand lever operated multi purpose soft seated wafer butterfly valve having centric disc construction one piece body, replaceable seal pn-1.6 pressure rating, SS-304 shaft, complete with matching flanges. ( make: Castle/NVR/Kartaror equivalent as approved by Engineer-in-charge)100mm dia
168Supply of Cast iron gear/hand lever operated multi purpose soft seated wafer butterfly valve having centric disc construction one piece body, replaceable seal pn-1.6 pressure rating, SS-304 shaft, complete with matching flanges. ( make: Castle/NVR/Kartar or equivalent as approved by Engineer-in-charge)150mm dia
169Supply of Cast iron gear/hand lever operated multi purpose soft seated wafer butterfly valve having centric disc construction one piece body, replaceable seal pn-1.6 pressure rating, SS-304 shaft, complete with matching flanges. ( make: Castle/NVR/Kartaror equivalent as approved by Engineer-in-charge)80mm dia
170Supply of Gun metal ball valve isi marked screwed type tested to 30 kg/cm2 pressure (IS-778-1984) of following sizes : (make: Sant /Zoloto/Kartaror equivalent as approved by Engineer-in-charge) 25mm dia
171Providing & fixing GM fire brigade suction hose coupling (draw-out connection) with nut for female coupling as per IS: 902-1974 complete with 100 mm dia GI suction pipe and 100 mm dia foot valve (to be connected to static tank). Provision of GI drop pipe and foot valve shall be made in all the fire water static storage tanks (2 No) (GI pipe to be paid separately through appropriate item while cost of foot valve to be included).(Omaxe/Newage/Atasee)
172Supplying, Installation, Testing and Commissioning offollowing type of Sprinkler headsUL listed and FM approvedcomplete withfusible glass capsule of 5 mm dia suitable for horizontal / pendenttype sprinkler"s head of 68 degree with powder coated conforming to relevantISammended upto datecomplete etc. as reqd. ( MAKE: Tyco/Atasee/Omaxeor equivalent as approved by Engineer-in-charge ) Pendent through type
173Providing & fixing in the false ceilings, high pressure metallic hose with fittings (25 NB at one end for connection to pipe and 15 NB at the other end for the Sprinkler) for connecting the Sprinklers to Sprinkler piping system, Hose & Fittings to be UL listed or FM approved and installed in accordance with para 9.2.1.3.3 of NFPA-13 (2007 edition) Test Pressure 10.0 Kg/Sq.m 1000mmor equivalent as approved by Engineer-in-charge
174SUPPLY:- Kirloskar/Willow Electrical motordrivenfirepumping set suitablefor automatic operation consisting of thefollowingas per specifications :- Horizontally mounted, centrifugal type single / multi - stage fire pump having cast iron body, bronze impeller, stainless steel shaft & capable of delivering 2280 lpm against a total head of 60 m complete with necessary periodical testing of the working of the pumping set as per specifications Squirrel cage induction motor totally enclosed fan cooled type suitable for 400/450 volts (+5%) 3 phase, 50 hz a.c. supply of suitable capacity (not less than 45 kw) for the above pump coupled with flexible coupling including earthing as per relevant indian standard and specification including cable box suitable for reqd. size of cable Common bed plate for mounting pump and motor fabricated of suitable m.s.channel as per manufacturer"s recommendations Suitable rcc foundationsfor pump & motoras per manufacturer"s design and 6 nos. anti-vibration (cushy foot) heavy duty mounting pads. ( make: kirloskar/ crompton/ mather & plattor equivalent as approved by Engineer-in-charge)
175Diesel engine driven fire pumping set suitable for automatic operation consisting of the following as per specifications :- Horizontally mounted, centrifugal type single/multi-stage fire pump having cast iron body, bronze impeller, stainless steel shaft & capable of delivering 2280 lpm against a total head of 70 m complete periodical testing of the working of the pumping set as per specifications. Water cooled diesel engine suitable 1800/1500 rpm for abovepump complete with automatic starting mechanism, batteries, automatic battery charger unit, flexible couplingwith the pump, fuel tank, silencer, exhaust pipe & all standard accessories as reqd. including earthing, mandatory spares and tool kit. Common bed plate for mounting pump and engine fabricated of suitable m.s.channel as per manufacturer"s recommendations. Suitable rcc foundations for pump & engineas per manufacturer"s design and 6 nos. anti-vibration (cushy foot) heavy duty mounting pads. ( make: keol/ caterpillar/ ashok leyland/ greavesor equivalent as approved by Engineer-in-charge)
176Electrical motor driven automatic pressurization (jockey) pumping set consisting ofthe following as per specifications :- Horizontally mounted, centrifugal type single/multi-stage fire pump for building pressure loss due to any leakage in the system and capable to deliver approx. 180 lpm against a total head of 70 m having cast iron body, bronze impeller, stainless steel shaft and complete withperiodical testing of the working of the pumping set. ( make: kirloskar/ crompton/ mather & platt ) Squirrel cage induction motor totally enclosed fan cooled type suitable for 400/450volts (+-5%) 3 phase, 50 hza.c. supply of suitable capacity (not less than 9.3 kw) for the above pump with synchronous speed of 1500/3000 rpm confirming to is:325 & duly coupled with above pump coupled with flexible coupling including earthing as per relevant indian standard and specifications including cable box suitable for reqd. size of cable. Common bed plate for mounting pump and motor fabricated of suitable m.s. channel as per manufacturer"s recommendations. Suitable rcc foundations for pump & motor as per manufacturer"s design and 4 nos. anti-vibration (cushy foot) heavy duty mounting pads. ( make: kirloskar/ crompton/ mather & plattor equivalent as approved by Engineer-in-charge)
177Cubical type floor mounted fire pump control panel fabricated from 16g m.s. sheet duly painted with stove enameledfinishofapprovedshadefor above said pumps Fully automatic diesel engine starting system complete with battery charger, hooter, indicating lights, transformer, rectifier, timer, volt-meter, ammeter,selector switches, push buttons, auxiliary relay etc. complete as required. All interconnecting power & control wires/cables of suitable size within the panel and from panel to motors, diesel engine, pressure switches, level switches etc. including brass glands and termination within fire pump house and earthing as per specifications (power cable size shall not be less than 31/2c x 90 mm sq. for main pump motor and 31/2 x 16 mm sq. for jockey pump motor.
178Cubical type floor mounted fire pump control panel fabricated from 16g m.s. sheet duly painted with stove enameledfinishofapprovedshadefor above said pumps Fully automatic diesel engine starting system complete with battery charger, hooter, indicating lights, transformer, rectifier, timer, volt-meter, ammeter,selector switches, push buttons, auxiliary relay etc. complete as required. All interconnecting power & control wires/cables of suitable size within the panel and from panel to motors, diesel engine, pressure switches, level switches etc. including brass glands and termination within fire pump house and earthing as per specifications (power cable size shall not be less than 31/2c x 90 mm sq. for Terrace Pump 5 HP
179Providing and fixing of dial type S.S Pressure Gauge with isolation cock and pipe complete as required. ( MAKE: H Guru/ Fiebigor equivalent as approved by Engineer-in-charge)Dial diameter 100 mm calibration 0-16 Kg
180Providing and fixing of Pressure switch complete as required.(MAKE: Indfoss/ Danfossor equivalent as approved by Engineer-in-charge)
181SUPPLY & FIXING OF :- ISI Marked ( ) portable fire extinguisher, carbon-dioxide type, powder coated, flat base including valve, dischargehorn and hose of not less than 10 mm dia. 1 m long & complete in all respects including initial fill with co2 gas confirming to filled to a filling ratio of not more than o.667 and wallsuspension bracket with necessary nuts/bolts or dash fasteners etc. complete. (type `a").(make:minimax / exflame/Ataseeor equivalent as approved by Engineer-in-charge) Capacity 4.5 KG.
182ABC (DRY POWDER) Fire extinguishers, capacity 4 kg. in hp steel cylinders isi marked & approved by cce, nagpur,powder coated, fitted with pressure indicating gauge, internal tube, squeeze level type valve fully charged with abc powder and pressurized by nitrogen complete in all respects including wall suspension bracket with necessary nuts/bolts or dash fasteners etc. complete. (type `a").(make:Minimax / Omaxe/Ataseeor equivalent as approved by Engineer-in-charge)
183Mechanical Foam type Fire Extinguisher. In HP Mild Steel Cylinders ISI marked TAC approved fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged complete in all respects including wall suspension bracket / trolley mounted and confoming to IS:910 (50 Ltr )
184Supply, Installation, Charging, Testing and Commisioning of Air Cooled VRV/VRF units withrotary/scroll Compressor capable of modulating capacity from 20%- 100% working on R410A with heating & cooling both. The prices should include any lifting, shifting and positioning of outdoor units. The unit shall be factory charged & any top-up gas/oil required for first charge should be included in the individual price quoted below. This shall include the nitrogen leak testing, oil charging, vaccumisation .The outdoor unit shall be a factory assembled unit housed in a sturdy weather proof casing constructed form rust-proofed mild steel panels coated with powder coated finish. The outdoor unit shall have multiple scroll compressors and be able to operate even in case of breakdown of one of compressor. Each fllor shall be connected to one circuit and shall be commisioned floor wise with all machines on the terrace only. Each circuit of outdoor units shall have a minmum of 3 cans (ODU) for redundancy incase of breakdown. The heat exchanger for Outdoor shall be constructed with copper tubes mechanically bonded to aluminium fins to form a cross fin coil. The Condenser fins must be coated with Anti-corrosive treatment.The following safety devices shall be part of the outdoor unit:- High Pressure Switch, Low Pressure Switch, Fan Motor Safety Thermostat, Over Current Relay, Fusible Plugs, Fuses. Each unit shall be equipped, with an oil separatorto ensure stable operation with long refrigerant piping. The outdoor units shall have a minimum COP of 3.8 at 100% loading condition in cooling only at outside ambient temperature of 42 deg.C dry bulb temperature and indoor temperauture of 19 deg.C wet bulb temperature, the ODU shall have condenser fan capable of minmum 7 speeds for saving energy at various loading conditions. all as per the approval of Engineer-in-Charge. BRANDS : DAIKIN, VOLTAS, SAMSUNG, TOSHIBA, PANASONIC,O-GENERAL, MITSUBISHI or equivalent. Mimimum 328 HP at 42 deg. Outside ambient conditions. (minimum 3 ODU in each circuit). THE ENTIRE EQUIPMENT INCLUDING INSTALLATION & GAS CHARGING ETC SHALL CARRY A WARRANTY OF 2 YEARS FROM THE DATE OF COMMISIONING FOR COMPLETE RUNNING OF THE SYSTEM
185Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 1 WAY CASSETTE INDOOR 2.0 TR
186Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 1 WAY CASSETTE INDOOR 1.6 TR
187Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 1 WAY CASSETTE INDOOR 1.0 TR
188Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 1 WAY CASSETTE INDOOR 0.8 TR
189Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 1 WAY CASSETTE INDOOR 0.6 TR
190Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 4 WAY CASSETTE INDOOR 4.0 TR
191Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 4 WAY CASSETTE INDOOR 3.2 TR
192Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 4 WAY CASSETTE INDOOR 2.6 TR
193Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 4 WAY CASSETTE INDOOR 2.0 TR
194Supply, installation, testing and commissioning of below mentioned capacity ceiling mounted cassette type air conditioners complete with fan and fan motor, air cooled condenser propeller fan, controls, inter connecting refrigerant piping, insulation with corded remote control with each unit, cabling, earthing, necessary galvanized steel supports etc. as per specification and drawing. All indoor units to have NO/NC contacts for direct control from occupancy sensor if not then the manufacturer shall provide key card access for NO/NC contacts within the quoted rates. All as per the approval of Engineer-in-Charge. 4 WAY CASSETTE INDOOR 1.6 TR
195Providing & fixing control cum transmission wiring for Power supply to indoor units using 2 core 1.5 sqm wire from distiribution board near power DB to the indoor andControlCablingof2 core x 1sqmm copperin suitable conduits to be placed on cable tray between indoor and out door unit & indoor unit & its remote controller and all other control wiring required for the full functioning of the HAVC system and its controls & BMS centralized controller. All HVAC piping , drainage and Cabling etc shall run at a height of 6 inches below RCC slab on continuous cable tray of appropriate sizes. all beams shall be core cut to allow for passage of pipes etc & filled back with expanded polyurethene foam. rates quoted are inclusive of core cutting and cable tray etc complate in all all respects including painting in desired colour all as per the approval of Engineer-in-Charge
196Centralised Controller compatible with BACnet/LONworks/ MODbus Protocol as required with BMS and touch screen central controller capable of controlling and monitoring the system thru computer and shall have all desired features like Operation of remote, setting of temeprature limit , temp range, fan speed, swing control, switching on & off etc.,status of running outdoor machines compressor etc. including power consumption monitoring of the entire system including each indivual indoor unit andhaving capacity to control all required no. ofIndoor units indiviually. the controller shall have to be integrated with the BMS system for full functionality with the BMS system being the main controller for the entire system. The manufacturer shall have to give full documentation, technical manuals etc to enable the system integrator to merge the BMS system with AC system. the BMS system shall have full control of switching on/off of all indoor & outdoor units, temp control, air flow control, status of running outdoor machines compressor etc. including power consumption monitoring of the entire system including each indivual indoor unit. the AC manufacturer shall provide any software /hardware, adaptor kits etc required for the handshake of BMS & AC equipment all as per the approval of the Engineer-in-Charge
197Providing, supplying and installing etc. of complete and comprehensive Annual Maintainence Contract inclusive of all spares, running, gas charging etc if required due to any reason complete in all respects for full running of the Air Conditioning systemfor a period 5 years after the expiry of the 2 years from the date of commisioning. The rate shall be quoted as a LOT for 5 years but shall be payable in equitable installmants every year.
198Supply and Installation of Interconnecting Refrigerant Piping of various sizes as required for the full functionality of the VRF system including refnet joints etc. complete in all respects duly insulated with closed cell nitrile rubber of superlon/armacell with UV barrier film as per specifications of the manufacturer. the contractor shall submit a detailed drawing approved by the manufacturer showing the piping sizes & layout to be followed at the site with the tender document. the contractor shall also get the drawingsshowing outdoor units in connection with indoor units approved from the architect in original from and then the head office of the manufacturer with a certificate stating that the piping layout is as per company specifications for full functioning of the VRF system. all piping shall be run in cable trays in interior and for exterior there shall be a cable tray both at the bottom and the top. all support system required for the installation of cable trays in interior or exterior shall be in the scope of the HVAC contarctor and nothing extra shall be paid for it.All HVAC piping , drainage and Cabling etc shall run at a height of 6 inches below RCC slab on continuous cable tray of appropriate sizes. all beams shall be core cut to allow for passage of pipes etc & filled back with expanded polyurethene foam. rates quoted are inclusive of core cutting and cable tray etc complate in all all respects including painting in desired colour. on exterior side the cable tray shall be mounted on top & bottom side for added protection as per the Directions of Engineer-in-Charge (Lower Ground Floor)
199Supply and Installation of Interconnecting Refrigerant Piping of various sizes as required for the full functionality of the VRF system including refnet joints etc. complete in all respects duly insulated with closed cell nitrile rubber of superlon/armacell with UV barrier film as per specifications of the manufacturer. the contractor shall submit a detailed drawing approved by the manufacturer showing the piping sizes & layout to be followed at the site with the tender document. the contractor shall also get the drawingsshowing outdoor units in connection with indoor units approved from the architect in original from and then the head office of the manufacturer with a certificate stating that the piping layout is as per company specifications for full functioning of the VRF system. all piping shall be run in cable trays in interior and for exterior there shall be a cable tray both at the bottom and the top. all support system required for the installation of cable trays in interior or exterior shall be in the scope of the HVAC contarctor and nothing extra shall be paid for it.All HVAC piping , drainage and Cabling etc shall run at a height of 6 inches below RCC slab on continuous cable tray of appropriate sizes. all beams shall be core cut to allow for passage of pipes etc & filled back with expanded polyurethene foam. rates quoted are inclusive of core cutting and cable tray etc complate in all all respects including painting in desired colour. on exterior side the cable tray shall be mounted on top & bottom side for added protection as per the Directions of Engineer-in-Charge (Upper Ground Floor)
200Supply and Installation of Interconnecting Refrigerant Piping of various sizes as required for the full functionality of the VRF system including refnet joints etc. complete in all respects duly insulated with closed cell nitrile rubber of superlon/armacell with UV barrier film as per specifications of the manufacturer. the contractor shall submit a detailed drawing approved by the manufacturer showing the piping sizes & layout to be followed at the site with the tender document. the contractor shall also get the drawingsshowing outdoor units in connection with indoor units approved from the architect in original from and then the head office of the manufacturer with a certificate stating that the piping layout is as per company specifications for full functioning of the VRF system. all piping shall be run in cable trays in interior and for exterior there shall be a cable tray both at the bottom and the top. all support system required for the installation of cable trays in interior or exterior shall be in the scope of the HVAC contarctor and nothing extra shall be paid for it.All HVAC piping , drainage and Cabling etc shall run at a height of 6 inches below RCC slab on continuous cable tray of appropriate sizes. all beams shall be core cut to allow for passage of pipes etc & filled back with expanded polyurethene foam. rates quoted are inclusive of core cutting and cable tray etc complate in all all respects including painting in desired colour. on exterior side the cable tray shall be mounted on top & bottom side for added protection as per the Directions of Engineer-in-Charge (1st Floor)
201Supply and Installation of Interconnecting Refrigerant Piping of various sizes as required for the full functionality of the VRF system including refnet joints etc. complete in all respects duly insulated with closed cell nitrile rubber of superlon/armacell with UV barrier film as per specifications of the manufacturer. the contractor shall submit a detailed drawing approved by the manufacturer showing the piping sizes & layout to be followed at the site with the tender document. the contractor shall also get the drawingsshowing outdoor units in connection with indoor units approved from the architect in original from and then the head office of the manufacturer with a certificate stating that the piping layout is as per company specifications for full functioning of the VRF system. all piping shall be run in cable trays in interior and for exterior there shall be a cable tray both at the bottom and the top. all support system required for the installation of cable trays in interior or exterior shall be in the scope of the HVAC contarctor and nothing extra shall be paid for it.All HVAC piping , drainage and Cabling etc shall run at a height of 6 inches below RCC slab on continuous cable tray of appropriate sizes. all beams shall be core cut to allow for passage of pipes etc & filled back with expanded polyurethene foam. rates quoted are inclusive of core cutting and cable tray etc complate in all all respects including painting in desired colour. on exterior side the cable tray shall be mounted on top & bottom side for added protection as per the Directions of Engineer-in-Charge (2nd Floor)
202Supply and Installation of Interconnecting Refrigerant Piping of various sizes as required for the full functionality of the VRF system including refnet joints etc. complete in all respects duly insulated with closed cell nitrile rubber of superlon/armacell with UV barrier film as per specifications of the manufacturer. the contractor shall submit a detailed drawing approved by the manufacturer showing the piping sizes & layout to be followed at the site with the tender document. the contractor shall also get the drawingsshowing outdoor units in connection with indoor units approved from the architect in original from and then the head office of the manufacturer with a certificate stating that the piping layout is as per company specifications for full functioning of the VRF system. all piping shall be run in cable trays in interior and for exterior there shall be a cable tray both at the bottom and the top. all support system required for the installation of cable trays in interior or exterior shall be in the scope of the HVAC contarctor and nothing extra shall be paid for it.All HVAC piping , drainage and Cabling etc shall run at a height of 6 inches below RCC slab on continuous cable tray of appropriate sizes. all beams shall be core cut to allow for passage of pipes etc & filled back with expanded polyurethene foam. rates quoted are inclusive of core cutting and cable tray etc complate in all all respects including painting in desired colour. on exterior side the cable tray shall be mounted on top & bottom side for added protection as per the Directions of Engineer-in-Charge (3rd Floor)
203Supply and Installation of Interconnecting Refrigerant Piping of various sizes as required for the full functionality of the VRF system including refnet joints etc. complete in all respects duly insulated with closed cell nitrile rubber of superlon/armacell with UV barrier film as per specifications of the manufacturer. the contractor shall submit a detailed drawing approved by the manufacturer showing the piping sizes & layout to be followed at the site with the tender document. the contractor shall also get the drawingsshowing outdoor units in connection with indoor units approved from the architect in original from and then the head office of the manufacturer with a certificate stating that the piping layout is as per company specifications for full functioning of the VRF system. all piping shall be run in cable trays in interior and for exterior there shall be a cable tray both at the bottom and the top. all support system required for the installation of cable trays in interior or exterior shall be in the scope of the HVAC contarctor and nothing extra shall be paid for it.All HVAC piping , drainage and Cabling etc shall run at a height of 6 inches below RCC slab on continuous cable tray of appropriate sizes. all beams shall be core cut to allow for passage of pipes etc & filled back with expanded polyurethene foam. rates quoted are inclusive of core cutting and cable tray etc complate in all all respects including painting in desired colour. on exterior side the cable tray shall be mounted on top & bottom side for added protection as per the Directions of Engineer-in-Charge (4th Floor)
204Providing PPR pipesof various sizes for condensed water drainage from Indoor unit to nearest disposal point in toilet/ outside rain water harvesting system as approved by Engineer-in-Charge (Lower Ground Floor)
205Providing PPR pipesof various sizes for condensed water drainage from Indoor unit to nearest disposal point in toilet/ outside rain water harvesting system as approved by Engineer-in-Charge (Upper Ground Floor)
206Providing PPR pipesof various sizes for condensed water drainage from Indoor unit to nearest disposal point in toilet/ outside rain water harvesting system as approved by Engineer-in-Charge (1st floor)
207Providing PPR pipesof various sizes for condensed water drainage from Indoor unit to nearest disposal point in toilet/ outside rain water harvesting system as approved by Engineer-in-Charge (2nd Floor)
208Providing PPR pipesof various sizes for condensed water drainage from Indoor unit to nearest disposal point in toilet/ outside rain water harvesting system as approved by Engineer-in-Charge (3rd Floor)
209Providing PPR pipesof various sizes for condensed water drainage from Indoor unit to nearest disposal point in toilet/ outside rain water harvesting system as approved by Engineer-in-Charge (4th Floor)
210Supply, installation, testing & commissioning of cubical Outdoor type IP65 rated main MV panel board suitable for 3 Phase, 50 Hz and of 35 MVA rupturing capacity at 415 volts, fabricated fromminimum 2mm thick CRCA sheet powder coated throughseven tank process facility for prickling and degreasing complete with following mountings, interconnections etc. as required. (GA drawing of panel to be provided before fabrication). Panel shall be Floor mounted type with cable entry at the top and IP Degree of protection for outdoor panels for complete water and weather proofing. Panel shall be powder coated having colour shade RAL-7032. (all switchgear shall be of legrand/schneider/hager/siemens or equivalent make as approved by Engineer-in-Charge). The authorised panel builders are CMKL/IPC or equivalent. Note:- Consider 0.8A / Sqmm current density for bus bar size calculation. PANEL FOR VRV / VRFIncoming 1 No.630 Amps, 4P MCCB,415 Volts, 50Hz Aluminium Busbars Outgoing each outdoor unit to have an indpendent outgoing of minimum 63A, 4P MCB,415 Volts, 50 Hz. With Neutral link for VRF / VRV. 1 No. 0 - 415 Volts, 96mm Square Digital Voltmeter with protection fuses & selector switch. 1 No. 0 - 100 Amps, 96mm square Digital Ammeter with CT"s and selector switch. 1 Set R Y B phase indicating lamps. Supply, laying, testing and commissioning of power cabling as per specification including end termination as required. Power Cabling (XLPE insulated &PVC sheathed,Aluminium Conductor of 1.1 KV grade on suitable size cable armoured, trays at bottom and top)
211From MCCB to VRV Outdoor Unit minimum 4C x 10 Sq. mm Copper Conductor ot higher as required at site by manufacturer. Each outdoor un it to have sperate cable for supply from panel.
212Providing and fixing manager table as per layoutwith ± 10 mm tolernace in dimentions Main table : 1500(L)x750(D)x740(H) with integrated return table:1350(L)x525(D)d740(H) TABLE TOP :- The Table Top is made of 25mm thick prelam particle board confirming to IS 12823 Interior Grade. The exposed edges of the table top are sealed with 2mm PVC edge banding. The height of the table top from the ground should be 740mm ± 10 mm. LEGS:- The legs aremade of 50 x 50mm thick Square pipe made of 1.6mm thick CRCA pipe duly powder coated. The powder coating thickness considered is 50 to 60 microns DFT.The levelers are made of Nylon 6 with M8 bolts insert moulded. TIE MEMBER: The tie member should be 80 x 40mm pipe structure made of 1.6mm thick CRCA duly powder coated. The powder coating thickness considered is 50 to 60 microns DFT. Structure to fully welded with all arc welding from inside eliminating manual finishing. None of the welding joints should be visible from outside MODESTY:Main table is provided with 18 mm thick prelam modesty panel of height 400 mm. PEDESTAL UNIT:- The Pedestal Unit of Dimensions 400W x 470D x 545mmH shall be made of 18mm thick pre laminated partical Board conforming to shall be : 12823 Interior Grade. All the exposed edges shall be sealed with 2mm thick PVC Imported edge banding on sides and bottom. The top and drawer facia shall be sealed with 2mm thick PVC edge. The drawer unit shall beof 1 box drawer and 1 file drawer. The sides of Inside drawer box are of prelam particle board. The drawer box shall be fitted with roller Slide for free movement. The drawer unit shall be provided with central locking system, where in the all two drawer are locked with one key.PVC recessed handles are provided for easy opening and closing of drawer. The drawer unit shall be fitted on castors (optional) for easy mobility. PVC edge banding are imported from Rehau or Dolken of Germany. The complete furniture unit shall be factory assembled with knock down fittings. The pedestal shall be fitted with additional (5th) castor to avoid topplig of pedestal in case of opening of any / all of thedrawer
213CHAIR FOR EXECUTIVE"S CABIN TABLE:HIGH BACKIN LEATHER FINISH WITH 1D ARMREST, 1 SYNCRO POINT MECHANISM, CLASS 4 GASLIFT, ALUMINIUM BASE AND PU CASTERS All Dim in MM with open tolerance of +/- 10mm and ANSI / BIFMA/X5.1 compliant chair Pure Leather, High Resilience PU foam, 1 Position locking with Back-safety return mechanism, Die casted aluminiumArmrests with PU armpad.side tilt tension adjustment knob can be operated while taking back support for better judgement of comfort. 360 degree revolving Back: (W) 55.0 cm x (H)70.5 Cm, Seat :(W)51.0 cm x (D) 49.0 cm,Overall Dimensions of Chair:Seat Height - min 43 to max 55 cm, Height-min 115.5 to max 127.5 cm.Width & Depth of Chair as measured from pedestal - Width-70.0 cm and Depth-70.0 cm The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed plywood & upholstered with leather and moulded polyurethane foam. The back shall be designed with contoured shape for extra comfort and made up of combination of 12mm (7 layers) & 4mm (3 layers) thick hot pressed plywood and 37mm thick, 32 Density U foam. Size of back shall be (W)-55.0cm, (H)-70.5 .0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. PU foam should be used in making seat which shall be moulded with density 55 +/- 5 kg/m ³ and hardness load 15-20 kgf for 50% compression.The armrests should made of black integral skin polyurethane with 50-70 shore "A" Hardness and reinforced with M.S insert.The armrests shall be fitted to the seat with seat/armrest connecting strip assembly made of HR steel.The mechanism of chair shall have following features:360 degree revolving type,Synchronized tilt, Back tilt with 1 position locking and Side tilt tension adjustment knob should be operated while taking back support for better adjustment of comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 12 cm.The pedestal shall be made of die-cast polished aluminium . It shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below. Heightfrom ground - min 115.5 to max 127.5 cm. Seat height - min 43.0cm to max 55 cm.Dimensions tolerance / variations shall be within +/- 1 cm.Chair tested as per ANSI/BIFMA x5.1 standards
214CHAIR FOR EXECUTIVE"S CABIN TABLE:HIGH BACKIN LEATHEREETE FINISH WITH 1-DARMREST, 1 SYNCRO POINT MECHANISM, CLASS 4 GASLIFT, NYLON BASE AND NYLON CASTERS All Dim in MM with open tolerance of +/- 10mm and ANSI / BIFMA/X5.1 compliant chair Upholstered with leatherette and HR moulded polyurethane foam, Synchro mechanism, 360 degree revolving type, Adjustable armrests , multi position locking, tilt tension adjustment, pneumatic height adjustment,Pedestal base with twin wheel castors. Back: (W) 50.0 cm x (H)59.0 Cm, Seat :(W)49.0 cm x (D) 44.0 cm, Overall Dimensions of Chair: Seat Height - min 45 to max 57.0cm, Height - min 104 to max 116 cm. Width & Depth of Chair as measured from pedestal - Width-70 cm and Depth-70 cm. The seatand back shall be made up of 1.2+/-0.1cm thick hot pressed plywood and Upholstered with leatherette and moulded polyurethane foam all around. The moulded polyurethane foam shall be of density 55+/-5 kg/m ³, and hardness load 15-20 kgf as per IS:7888 for 25% compression.The dimensions of seat shall be- 49.0cm(W) x 44.0cm(D) and of back shall be 50 cm(W) x 59 cm(H).The armrests should made of black integral skin polyurethane with 40-55 shore hardness and reinforced with M.S insert. The mechanism of the chair shall have following features : 360° revolving type, Synchro multi position mechanism, Tilt tension adjustment . The chair shall be provided with pneumatic height adjustment which shall have stroke of 12 cm.The pedestial shall be in Nylon. It shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65 +/- 1 cm pitch-centre-dia (70 +/- 1.0 cm with castors). The twin wheel castors shall be made black PU. Overall dimensions of Chair shall be, Width of Chair - 76.3cm, Depth of Chair - 76.3 cm as measured from pedestal below. Height from ground - min 104.0 to max 116.0cm. Seat height - min 45.0 to max 57.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA x5.1 standards
215Providing and fixing Executive"s tableas per layout with ± 10 mm tolernace in dimentions MAIN TABLE : 2100(L)X900(D)X740(H) MM,EXTENSION TABLE TOP 750(L)X1150(D)X740(H) & SIDE TABLE UNIT 1500(L)X500(D)X740(H) MM & PEDESTAL DRAWER UNIT I.E. B+F (400(W)X470(D)X545(H) WITH 2 NOS BACK UNIT I.E. HINGED DOOR SHUTTER UNIT 900(W)X450(D)X740(H) MM MAIN TABLE: - The Table top is made of Particle Board with 1mm top laminate and 1mm bottom laminate. The complete Table top is 36mm thick. All exposed edges have 2mm PVC edge banding. MODESTY PANEL: - The Modesty is made of 18mm Particle Board with 1mm top laminate and 1mm bottom laminate. All exposed edges have 2mm PVC edge banding. UNDERSTRUCTURE:-The understructure is 200mm wide on one side is 25mm. It is made up of prelam particle board and is black in colour. The understructure has wire management properties and can carry concealed wires within it. All exposed edges have 2mm PVC edge banding. WIRE MANAGEMENTt :-The understructure has the capability of carrying wires within it. The main table has an access flap arrangement for easy access of switches and sockets for connecting the gadgets. The access flap cover is made of Aluminum extrusion and powder coated upto 50-60 microns EXTENSION TABLE: the table top is of an arc shape. The Table top is made of Particle Board with 1mm top laminate and 1mm bottom laminate. All exposed edges have 2mm PVC edge banding. The complete Table top is 36mm thick and shall be in black colour.SIDE TABLE: - The Table top is made of 36mm Particle Board with 1mm top laminate and 1mm bottom laminate. All exposed edges have 2mm PVC edge banding. The Table top colour is matching to the main table MODESTY PANEL: - The Modesty is made of 18mm Particle Board with 1mm top laminate and 1mm bottom laminate. All exposed edges have 2mm PVC edge banding. The colour of the modesty is matching to the table top colour. UNDERSTRUCTURE :-The understructure is made of 25mm thick prelam particle board and is black in colour. All exposed edges have 2mm PVC edge bandingBACK STORAGE UNIT : 1800(W)X450(D)X740(H) The back storage shall has 2 sections; namely storage unit and display unit (above the storage space). The storage caracass is made of 18mm thick prelam particle board of black colour. The storage top is made of 36mm Particle Board with 1mm top laminate and 1mm bottom laminate. The shutters are made of 18mm Particle Board with 1mm top laminate and 1mm bottom laminate. The storage back is made of 9mm thick prelam particle board. The shutter and storage top colour is matching to the main table. The storage is completely handle less and is openable from the top. All exposed edges have 2mm PVC edge banding PEDESTAL DRAWER UNIT: 1box drawer unit & 1 File drawer unit in size 400(W)X470(D)X545(H) shall be made up of 18mm thk. Medium Density Fiber (MDF) top & front facia board having central locking system & having wave key technology. Drawers shall be with roller slide mechanshall bem and casters for added mobility.
216Providing and fixing Executive"s tableas per layout with ± 10 mm tolernace in dimentions MAIN TABLE WITH INTEGRATED SIDE TABLE OVERALL SIZE OF MAIN TABLE : 1500(L)X750(D)X740(H) MM,INTEGRATED SIDE TABLE UNIT 1350(L)X600(D)X740(H) MM & PEDESTAL DRAWER UNIT I.E. B+B+B (500(W)X500(D)X585(H) All Dim in MM with open tolerance of +/- 10mm MAIN TABLE ConsideringPrimary Work Surface shall be made of 48mm ThickMDF board,which is joined by combining 2 table tops. The table tops have a dual tone with the lower top being in matt black colour.The Table top has chamfered edge adding to the aesthetics and the drip-proof profile. No polishing is done thereby ensuring low VOC (Volatile Organic Compounds). The overall thickness of the Table top from visible side 48mm.GABEL END: Shall be made of 48 mm thick MDFboard wrapped with membrane i.e. finish with 3D-thermoformable furniture film, calandered PVC uni colored, top shall be coated with lacquer andBackside shallbe finish with adhesion promoting primer.MODESTY: Shall be made of 18 mm thickMDF board wrapped with membrane finish i.e. with 3D-thermoformable furniture film, calandered PVC uni colored. UNDERSTRUCTURE: 75mmX75mmX5mm HRCA section used as inner bracket connecting table top to gable end.The understructure has wire management properties and can carry concealed wires within it.SIDE STORAGE UNIT: Shall be made of18 mm thick MDF panels with membrane fisnish.Complete unit must have two shutters and open shelfs in between, Shutters are hinged base, All inner structural panels are pre-lam particle boards. All handles for storages are Stainless Steel finish
217Providing and Fixing Manageable wireless access point dual band minimum 2300 MBPS, WiFi 6, ceiling mount along with centralized management perpetual software license of make as approved by the Engineer-in-Charge complete in all respects
218Supply, Installation, Testing and Commissioning of Point to point RF link 450 MBPS+ 400mm dish reflector, Minimum 22 Dbi Gain, Memory 64 MB DDR2, 16 MB Flash, POE, Wind survivivablity - 120 Km/h
219Supply, Installation, Testing and Commissioning of Number of Ports: 24 x SFP ports, 4 x 10G SFP+ ports , RJ-45 console port, Switching Capacity: 128 Gbps ,  Memory: 256 MB,  Flash: 32 MB, Other Standards : IEEE 802.3i 10BASE-T Ethernet (twisted-pair copper):  IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper) Auto-negotiation,loaded with SFP modules , enterprise series
220Technical Vetting of DPR including specifications of Electrical/Mechanical/Networking componentsby reputed Govt. Institution i.e IIT/NIT/GCET or equivalent including Soil bearing tests
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail