Assam Tourism Development Corporation Limited has published Upgradation Of Tourist Facilities At Kaziranga . Submission Date for this Tender is 05-08-2022. Civil Work Tenders in Golaghat Assam. Bidders can get complete Tender details and download the document.
Sl. No. | Item Description |
1 | CIVIL WORKS |
2 | EARTH WORK IN EXCAVATION Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in- charge. All kinds of soil. |
3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
5 | PLINTH FILLING Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
6 | ANTI-TERMITE TREATMENT Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
7 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration |
8 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
9 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
10 | SURFACE DRESSING AND JUNGLE CLEARING Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil |
11 | CLEARING JUNGLE:including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
12 | CLEARING GRASS : and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. |
13 | CONCRETE WORKS: 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
14 | CONCRETE WORKS:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
15 | DAMP-PROOF COURSE Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) |
16 | PLINTH PROTECTION Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth. |
17 | PLINTH PROTECTION DRAIN Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. i) 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm. |
18 | DRAIN COVER:Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge. a) 100 mm thick slab |
19 | REINFORCED CEMENT CONCRETE WORKS Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
20 | REINFORCED CEMENT CONCRETE WORKS: Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) |
21 | REINFORCED CEMENT CONCRETE WORKS: Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of sqm5 grade with minimum cement content of 300 kg /cum |
22 | All works above plinth level upto floor V level Concrete of sqm5 grade with minimum cement content of 300 kg/cum |
23 | CENTERING AND SHUTTERING :Centering and shuttering including strutting, propping etc. and removal of for :Foundations, footings, bases of columns, etc. for mass concrete |
24 | CENTERING AND SHUTTERING :Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
25 | CENTERING AND SHUTTERING: Suspended floors, roofs, landings, balconies and access platfoMetre |
26 | CENTERING AND SHUTTERING:: Lintels, beams, plinth beams, girders, bressumers and cantilevers |
27 | CENTERING AND SHUTTERING:Columns, Pillars, Piers, Abutments, Posts and Struts |
28 | CENTERING AND SHUTTERING:Edges of slabs and breaks in floors and walls Under 20 cm wide |
29 | CENTERING AND SHUTTERING:Weather shade, Chajjas, corbels etc., including edges |
30 | STEEL REINFORCEMENT Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. TheMetreo-Mechanically Treated bars of grade Fe-500D or more. |
31 | STEEL REINFORCEMENT: Mild steel and Medium Tensile steel bars |
32 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
33 | MASONRY WORK Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
34 | MASONRY WORK:Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement : 4 coarse sand) |
35 | MASONRY WORK:Providing soling in foundation and under floorwith stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labourand materials and if necessary dewatering, complete.(a).Brick on flat soling. |
36 | RANDOM RUBBLE MASONRY Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand) |
37 | CEMENT CONCRETE FLOOR: 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer"s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
38 | MS GRILL Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. |
39 | STAINLESS STEEL RAILING Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. |
40 | ALUMINIUM FITTINGS Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300mm X 16mm. |
41 | ALUMINIUM FITTINGS: Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete: 300x10 mm |
42 | ALUMINIUM FITTINGS:Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm |
43 | ALUMINIUM FITTINGS:Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper |
44 | STEEL WORK ( GATE AND POST) Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
45 | STEEL WORK (M.S. STAIR) Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.1 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete |
46 | STEEL TRUSS:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes |
47 | FAN HOOK : Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete. |
48 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
49 | MORTICE LOCK: Providing and fixing SS mate finished 240 mm Lock Body Chrome mortice lock with 6 levers including a pair of SS mat finished handles of approved quality for Wooden and FRP door, with necessary screws etc from reputed brand like Godrej, Hettic, Hafele or equivelent. Complete as per direction of Engineer- in-charge. |
50 | DOOR HANDLE WITH LOCK :Sypplying and fixing 200 mm Door Handle set with Lock Body 2C SS SS mat finished handles of approved quality for door, with necessary screws etc from reputed brand like Godrej, Hettic, Hafele or equivelent. Complete as per direction of Engineer- in-charge. |
51 | HINGE:Providing and fixing bright finished brass double acting spring hinges with necessary brass screws etc. complete: 100 mm |
52 | MARBLE FLOORING Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. |
53 | GRANITE FLOORING Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platfoMetres, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 8.2.2 Granite stone slab colour black, Cherry/Ruby red8.2.2.2 Area of slab over 0.50 sqm |
54 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
55 | Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. 8mm thick Granite of any colour and shade |
56 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
57 | COLOUR COATED ROOFING SHEET:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
58 | RIDGES:Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) |
59 | RAIN WATER PIPE Providing and fixing on wall face unplasticised Rigid PVC rain water pipes confoMetreing to IS : 13592 Type A, including jointing with seal ring confoMetreing to IS : 5382, leaving 10 mm gap for theMetreal expansion, (i) Single socketed pipes. 100 mm diameter |
60 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes confoMetreing to IS : 13592 Type A, including jointing with seal ring confoMetreing to IS : 5382, leaving 10 mm gap for theMetreal expansion.Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes confoMetreing to IS : 13592 Type A, including jointing with seal ring confoMetreing to IS : 5382, leaving 10 mm gap for theMetreal expansion. 75 mm |
61 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes confoMetreing to IS : 13592 Type A, including jointing with seal ring confoMetreing to IS : 5382, leaving 10 mm gap for theMetreal expansion. 75 mm bend |
62 | CEMENT PLASTERING 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) |
63 | CEMENT PLASTERING:15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand) |
64 | CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand) |
65 | WATER PROOFING IN CEMENT PLASTER :Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
66 | SPOUT:Providing and fixing 100 mm diameter and 60 cm long rain water spout in cement mortar 1:4 (1 cement : 4 fine sand).Stone ware spout |
67 | R.C.C MANHOLE COVER:Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality:L D- 2.5:Rectangular shape 600x450 mm internal dimensions |
68 | PAINTING WORKS EXTERNAL PAINTING Finishing old / new wall with water proofing weather coatsmoothanti-fungalexteriorpaintingof approved make of paint of required shade after cleaning andclearingthesurfaceetc.includingscaffolding complete as directed at all levels (two coats)Berger paint / Asian Paint / Dulax (ICI) paint/ Nerolac Paint / Snowcem India Ltd. |
69 | WATER PROOFING CEMENT PAINT:Finishing walls with water proofing cement paint of required shade: New work (Two or more coats applied @ 3.84 kg/10 sqm) |
70 | PRIMER ( WOOD ): Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
71 | PRIMER ( STEEL ): Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works |
72 | PAINT ( WOOD AND STEEL )Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
73 | INTERNAL PAINTING (PLASTIC PAINT) Wall painting with acrylic emulsion paint of approved brand andmanufacture to give an even shade : Two or more coats on new work |
74 | WALL PUTTY:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
75 | CEMENT PRIMER:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface with water thinnable cement primer. |
76 | VARNISHING AND POLISHING: Varnishing with varnish of approved brand and manufacture : Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish |
77 | POLISHING:French spirit polishing : Two or more coats on new works including a coat of wood filler |
78 | PAINTING OF PIPES:Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with aluminium paint of approved brand and manufacture over a priming coat of ready mixed zinc chromate yellow primer on new work : :75 mm diameter pipes metre |
79 | PAINTING OF PIPES:Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with aluminium paint of approved brand and manufacture over a priming coat of ready mixed zinc chromate yellow primer on new work : 100 mm diameter pipes metre |
80 | SOAK PIT: 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
81 | INSPECTION CHAMBER: Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
82 | CEMENT BOARD CLADDING Providing and fixing of external wall system on Light gauge steel frame work with outer face cement boards as per standard sizes fixed with self- drilling / taping screws / fasteners @ 60cm c/c of approved make. A groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. The board shall be fixed in a staggered pattern. Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. Internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with selfdrilling / taping screws / fasteners @ 60cm c/c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately) Outer face: Outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, Type A, as per IS:14862:2000 (high pressure steam cured) Inner Face :- 12.5 mm thick gypsum plaster board confoMetreing to IS 2095:2011 fixed on 8 mm thick fibre cement board confiMetreing to IS:14862:2000 of type B (High pressure steam cured) |
83 | DOOR CLOSER :Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
84 | FLOOR SPRING: Providing and fixing double action hydraulic floor spring of approved brand and manufacture confoMetreing to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 m thickness |
85 | HUME PIPE:Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm dia. R.C.C. pipe |
86 | G.I. PIPE:Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall,50 mm dia nominal bore |
87 | G.I. PIPE: Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work:, 50 mm dia nominal bore |
88 | THATCH ROOF STRUCTURE :: Supplyingof materialslike bamboo , thatch , wire, rope etc to constructed a juhal with mud plaster in wall and kacha floor as per architectural drawing anddesign. Finished and complete as per instruction of Engineer incharge. |
89 | TUBE WELL: Labour for test boring with 40mm (internal) dia G.I. Pipes including keeping surplus of earth and every 2.00m after first 3.00m depth and delivering the same in nearest P.W.D. camp in the small tin container(container, scaffolding, tools etc. will have to be arranged by the contractor at his own cost). |
90 | MACHINE BORING :of deep tube well upto 200mm dia. Bore hole asdirected by the Engineer in Charge |
91 | PUMP:Supplying including installation, connection as approved by the Deptt., testing and commissioning of SUBMERSIBLE PUMP SET3 (Three Phase)with steel cable rope and submersible cable complete as directed and specified by the deptt.:Three phase Submersible motor pump set(Texmo / Crompton Greaves/ Aquatic/ CRI/ V-Guarsuitable for 100 mm bore well and above. 2 HP with MCB controlled Submersible motor pump set control panel. |
92 | PUMP:Supplying including installation, connection as approved by the Deptt., testing and commissioning of JET PUMP SET (HORIZONTAL) complete as directed and specified by the deptt.:1 HP single Phase jet pump set (Horizontal (Crompton Greaves/ Aquatic/ CRI/ V-Guardmake)2900 rpm with DOL Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemensmake) . |
93 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia |
94 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, confoMetreing to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia |
95 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (SUCTION PIPE) :50 mm nominal outer dia Pipes |
96 | Providing and placing in position filters of 40 mm diameter G.I./PVCpipe with brass strainer of approved quality. |
97 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal outer dia Pipes Horizontal |
98 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal outer dia Pipes Vertical |
99 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond peMetreissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
100 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
101 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia |
102 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia |
103 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. :200 mm clamp |
104 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 150 mm dia. |
105 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).:200 mm dia |
106 | Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. |
107 | Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. |
108 | Providing and displaying of Croton baby golden variety having ht.30 cm and above, well developed with full of fresh and healthy leaves in 20 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge. |
109 | Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. |
110 | Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge. |
111 | Providing and displaying of Dracaena rosea having ht. 30 cm & above with 8 to10 leaves, well developed, fresh and healthy in 20 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge. |
112 | Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge. |
113 | Providing and stacking of Peltophorum species of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. |
114 | Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge. |
115 | Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge |
116 | Providing and stacking of Bombax ceiba of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. |
117 | Providing and stacking of Jacaranda mimosifolia of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. |
118 | Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
119 | Providing and stacking of Chlorophytum-variegated, full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
120 | Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
121 | Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. |
122 | Providing and displaying of Chamaedorea elegans palm having ht. 60 cm to 75 cm, well developed with fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot. & as per direction of the officer-in-charge. |
123 | Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge |
124 | Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (DhuMetreos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge. |
125 | Providing and stacking of Thuja compacta of height 75-90 cm., conical shaped, well foMetreed with healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge. |
126 | Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. |
127 | Supplying and installation of free hold hanging dust bin made out of FRP di moulded min 4mm thick body thickness with necessary tilting arrangement design for easy cleaning from reputed brand like supreme, sintex or equivalent. The dust bin will be placed in pair of red and green colour but with provision of individual-tilting provision. the bidder should obtain prior approval of design of the dustbin before installation from the authority. The rate is inclusive of required civil works for fixing the same in position. |
128 | Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure). |
129 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment). |
130 | Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment). |
131 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : :Screened through sieve of I.S. designation 20 mm |
132 | Rough dressing the trenched ground including breaking clods. |
133 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). |
134 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge |
135 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately Holes 90 cm dia, and 90 cm deep |
136 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately :Holes 60 cm dia, and 60 cm deep |
137 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately Holes 45 cm dia, and 45 cm deep. |
138 | Turfing with Sods :(Furnishing and laying of the sqm 31.00 live sods of perennial turf foMetreing grass on embankment slope, verges or other locations shown on the drawing or as directed by the engineer including preparation of ground, fetching of rods and watering) |
139 | Oudoor Children playing equipment.:SINGLE SEATER SPRING RIDER Supplying, installation, testing & commissioning of multi activity play system of reputed brand or manufacturer made out of GI/ MS :- Class B and confoMetreing to IS-1239. LLDPE Plastic :-UV Stabilized.HT SPRING : Jerk resistance, heigh strength, Flexible. FRP SLIDE, SEAT & STRIP : Fiber Rainforce Plastic is layer of pigment, resin & hardner material, thikness 4 to 8 mm, die moulded process, glossy finish surface Acrylic :- Acrylic clarity, light weight, impact resistance, and weather resistance. Aluminium Clamp :- high fatigue strength, excellent castability, very good corrosion resistance,self-piercing riveting and clinching. PP Caps :- caps are manufactured from high quality polymers. GI Hardware:- All galvanizing hardware are carried out by the hot dip process, in accordance with specification IS 2629. Vinyle Sticker :- High Strength Acrylic Adhesive 300 is designed to be compatible with a variety of print methods and end use applications. MIG welding :- it is versatile and can be used with a variety of metals and alloys, corrosion resistance, soft surface to prevent injuries. Powder Coating :-The finish is more flexible than traditional paint, and allows for a small amountof bending and flexible as parts vibrate and move. Rubber belt :- Rubberized coating oover the steel core, height strength, flexible |
140 | Oudoor Children playing equipment.:2 SEATER ARC SWING Supplying, installation, testing & commissioning of multi activity play system of reputed brand or manufacturer made out of GI/ MS :- Class B and confoMetreing to IS-1239. LLDPE Plastic :-UV Stabilized.HT SPRING : Jerk resistance, heigh strength, Flexible. FRP SLIDE, SEAT & STRIP : Fiber Rainforce Plastic is layer of pigment, resin & hardner material, thikness 4 to 8 mm, die moulded process, glossy finish surface Acrylic :- Acrylic clarity, light weight, impact resistance, and weather resistance. Aluminium Clamp :- high fatigue strength, excellent castability, very good corrosion resistance,self-piercing riveting and clinching. PP Caps :- caps are manufactured from high quality polymers. GI Hardware:- All galvanizing hardware are carried out by the hot dip process, in accordance with specification IS 2629. Vinyle Sticker :- High Strength Acrylic Adhesive 300 is designed to be compatible with a variety of print methods and end use applications. MIG welding :- it is versatile and can be used with a variety of metals and alloys, corrosion resistance, soft surface to prevent injuries. Powder Coating :-The finish is more flexible than traditional paint, and allows for a small amountof bending and flexible as parts vibrate and move. Rubber belt :- Rubberized coating oover the steel core, height strength, flexible |
141 | Oudoor Children playing equipment.: ADVENTURE CLIMBER Supplying, installation, testing & commissioning of multi activity play system of reputed brand or manufacturer made out of GI/ MS :- Class B and confoMetreing to IS-1239. LLDPE Plastic :-UV Stabilized. Acrylic :- Acrylic clarity, light weight, impact resistance, and weather resistance. Aluminium Clamp :- high fatigue strength, excellent castability, very good corrosion resistance,self-piercing riveting and clinching. PP Caps :- caps are manufactured from high quality polymers. GI Hardware:- All galvanizing hardware are carried out by the hot dip process, in accordance with specification IS 2629. Vinyle Sticker :- High Strength Acrylic Adhesive 300 is designed to be compatible with a variety of print methods and end use applications. MIG welding :- it is versatile and can be used with a variety of metals and alloys, corrosion resistance, soft surface to prevent injuries. Powder Coating :-The finish is more flexible than traditional paint, and allows for a small amountof bending and flexible as parts vibrate and move. Rubber belt :- Rubberized coating oover the steel core, height strength, flexible. |
142 | Oudoor Children playing equipment.: 2 SEATER SPRING SEE-SAW Supplying, installation, testing & commissioning of multi activity play system of reputed brand or manufacturer made out of GI/ MS :- Class B and confoMetreing to IS-1239. LLDPE Plastic :-UV Stabilized.HT SPRING : Jerk resistance, heigh strength, Flexible. FRP SLIDE, SEAT & STRIP : Fiber Rainforce Plastic is layer of pigment, resin & hardner material, thikness 4 to 8 mm, die moulded process, glossy finish surface Acrylic :- Acrylic clarity, light weight, impact resistance, and weather resistance. Aluminium Clamp :- high fatigue strength, excellent castability, very good corrosion resistance,self-piercing riveting and clinching. PP Caps :- caps are manufactured from high quality polymers. GI Hardware:- All galvanizing hardware are carried out by the hot dip process, in accordance with specification IS 2629. Vinyle Sticker :- High Strength Acrylic Adhesive 300 is designed to be compatible with a variety of print methods and end use applications. MIG welding :- it is versatile and can be used with a variety of metals and alloys, corrosion resistance, soft surface to prevent injuries. Powder Coating :-The finish is more flexible than traditional paint, and allows for a small amountof bending and flexible as parts vibrate and move. Rubber belt :- Rubberized coating oover the steel core, height strength, flexible. |
143 | GAEDEN CHAIR:Supplying and Installation of Garden Seating of minimum overall dimension of 1550mm x 850mm and height 600mm (fixing height 400-450mm) made out of MS structure (pipe,flat,etc where applicable) welded and finished smooth. The finishing should be of weather proof powder coating of pipe end should be of weather proof powder coating of approved colour. All the joints, hole, opening of pipe end should be water proof. The successful bidder need to get approval of physical sample from the authority before finalization of the bench. The rate is inclusive of fixing the chair in position including civil works. |
144 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. |
145 | Supplying and stacking at site. : Stone screening 11.2 mm nominal size (Type B) |
146 | Supplying and stacking of graded stone aggregate at site of size range.:90 mm to 45 mm |
147 | Supplying and stacking of graded stone aggregate at site of size range.: 63 mm to 45 mm |
148 | Supplying and stacking of graded stone aggregate at site of size range.: 53 mm to 22.4 mm |
149 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density. |
150 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. : 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
151 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
152 | DISMANTKING AND REPAIR WORKS: Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
153 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
154 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
155 | Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer in-charge. |
156 | Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work. |
157 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. (In cement mortar) |
158 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below |
159 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres |
160 | Taking out doors, windows and clerestory window shutters/ Collapsible gate (steel or wood) including stacking within 50 metres lead: Of area 3 sq. metres and below |
161 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: Of area beyond 3 sq. metres |
162 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : Of sectional area 40 square centimetres and above |
163 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :Of sectional area below 40 square centimetres |
164 | Dismantling tile work in floors/ Wall and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm. |
165 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles above 25 mm and up to 40 mm |
166 | Demolishing dry brick pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within 50 metres lead : |
167 | Dismantling roofing including ridges, hips, valleys and gutters etc., G.S. Sheetand stacking the material within 50 metres lead of: |
168 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
169 | Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :75 to 80 mm dia pipe |
170 | Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead: 100 mm dia pipe |
171 | Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : 150 mm dia pipe |
172 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :: 15 mm to 40 mm nominal bore |
173 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge ::Above 40 mm nominal bore |
174 | Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge: Up to 150 mm diameter |
175 | Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge: :Above 150 mm dia up to 300 mm dia |
176 | Dismantling of flushing cistern /W.C./ Wash basinof all types (C.I./PVC/Vitreous China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
177 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
178 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
179 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.: With cement mortar 1:4 (1 cement : 4 fine sand) |
180 | Fixing of old wind tie with new fittings including painting two or more coats with anticorrosive bitumastic paint of approved brand & manufacturer over and including priming coat of ready mixed zinc chromate yellow primer of approved brand. |
181 | Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge. For door/ window/ clerestory window |
182 | Renewing wooden beams in roofs including making good the holes in walls and painting with oil type wood preservative of approved brand and manufacture complete, including removal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. Not exceeding 4.00 metres in length.: Sal wood beams |
183 | Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineerin- Charge. (a) Internal Work- Exposed on wall |
184 | Renewing wooden battens in roofs, including making good the holes in wall and painting with oil type wood preservative of approved brand and manufacture complete, including removal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. Sal wood battens |
185 | M.S. STAIR:Taking out existing M.S. Spiral staircase,repair by cleaning, painting etc. and refixing of the stair in existing wall including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge . |
186 | WATER SUPPLY AND SANITARY WORKS:EWC Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
187 | EWC: Providing fitting and fixingVitreous china wall hang water closet (European type W.C pan 400mm high)with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) a) White (ii) Wall mounted Closet (inclusive of seat cover and fittings) Jacquar Model no. DRS-WHT-37951 HindwareModel no. 92097 (P-21) Kohler Model no. K-17647IN-S-0 |
188 | CONCEALED CISTERN Supplying, fitting and fixing concealed cisternwith all internal fittingswith CI brackets including supplying, fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified Concealed Cisternwith Control Plate (CP) from approved manufacturer. HindwareModel no. 518237(Concealed Cistern), HindwareConcealo Neo (Aura) (Flush Plate) Roca Model no. RE890010100(Concealed Cistern) , Roca Model no. RE890195000 (Flush plate)Kohler Model no. K-77029IN-M-NA(Concealed Cistern), Kohler Model no. K-4177IN-M-CP(Flush plate) |
189 | WASH BASIN Providing vitreous Chinawash basinwith CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) BASIN (with pedestal) Jacquar Model no. CNS-WHT-801 AND 301 Roca Model no. RS337461_ _0 HindwareModel no. 10012 |
190 | KITCHEN SINK Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 250 mm |
191 | WALL MIXTURE Providing and fixing CP Brass Single lever wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia |
192 | WASTE PIPE Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste pipe fittings complete. Semi rigid pipe 40 mm dia |
193 | MIRROR Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm |
194 | GLASS SHELF Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
195 | TOILET PAPER HOLDER: Providing and fixing toilet paper holder : C.P. brass |
196 | URINALS: Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. |
197 | BIB COCK: Providing and fixing C.P. brass long body bib cock of approved quality confoMetreing to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
198 | STOP COCK : 15 MM Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make confoMetreing to IS:8931 : 15 mm nominal bore |
199 | STOP COCK: 20MM Providing and fixing brass stop cock of approved quality : 20 mm nominal bore |
200 | ANGLE VALVE: Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality confoMetreing to IS:8931: 15mm nominal bore |
201 | BOTTLE TRAP: Providing and fixing CP Brass 32 to 40 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
202 | SHOWER ROSE: Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter |
203 | TELEPHONICSHOWER :Supplying fitting and fixing Telephonic Chrome Plated (C.P.) shower of approved brand as directed and specified. (Pipes will be measured and paid separately) Jaquar make: a) Continental(i) Telephone shower 2-in-1 shower with massage effect with 1.5m SS tube and swinging wall hook |
204 | FLOOR TRAP :Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent aMetre complete, including cost of cutting and making good the walls and floors 100 mm inlet and 75 mm outlet: Silver with crome finish solid construction fast drainage and automatic sealing |
205 | WASTE COUPLING FOR BASIN: Providing and fixing CP Waste Coupling for wash basin of approved quality 31 mm dia of 79 mm length and 62mm breadth |
206 | WASTE COUPLING :FOR SINK Providing and fixing CP POP-UP HALF COVER Waste Coupling for kitchen of approved quality38 mm dia of 83 mm length and 77mm breadth |
207 | TOWEL RACK: Providing and fixing CP brass towel rack of dimension not less than : 240mm x 613mm x 115mm weight not less than 475 Grams shelf with min three bars and arrangement for keeping unfolded towels below the rack. Including fitting with concealed fittings arrangement of approved quality. |
208 | TOWEL RING: Providing and fixing CP towel ring ovel shape minimum dimensions 21.4 x 1.5 x 14.4 Centimeters with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality , weighing not less than 88 gms. |
209 | BASIN MIXER supplying fitting and fixing of single lever CP brass basin mixer foam flow faucet with seven years warranty, shiny-reflective body finished of approved make including connection pipes from agnular stop cock and finished as per instruction of engineer in charge |
210 | SOAP TRAY Providing, fitting and fixing C.P. soap tray/ soap dish complete as directed and specified. |
211 | SINK COCK:Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) (i) Sink cock with swinging casted spout |
212 | LIQUID SOAP DISPENSER Providing, fitting and fixing Liquid soap dispenser and liquid soap containercomplete as directed and specified. Fittings with glass bottle. Jaquar Model no. ACN-1137Nor equivalent product from Hindware, Roca, Kohler. |
213 | COUNTER TOP WASH BASIN: Providing vitreous Chinawash basinwith CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls/ platfoMetre wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) |
214 | HAND DRYER Supplying, installation, testing and commissioning of Automatic Jet Hand Dryer of following specifications and complete as per direction of Engineer in charge.Prior Approval of the brand should be obtained from the authority before supply of the product. • Colour : as per designHindware/ Jaquar/ Roca/ Kohler or Equivalent |
215 | HEALTH FAUCET Supplying fitting and fixing hand shower (health faucet) ABS with rubbit cleaning system, 1.25 m long PVC flexible tube with ABS wall hook and operating knob complete in all respects. Hindware(Cat No. F160013) Jaquar(Cat No. ALD-563) or Equivalent |
216 | COWEL :Providing fitting and fixing PVC cowel of ISI make completeas directed and specified. (iii)90 to 150mm dia. PVC cowel of ISI make |
217 | GRAB BAR: Providing, fitting and fixing CP Grab bar(600mm long). complete as directed and specified. Jaquar Model no. AKP-35711PS Roca Model no. RA816070165 Hindware Model no.F840012 |
218 | BATHTUB: Supplying fitting and fixing bath tub including providing necessary fittings complete as directed and specified.(pipes will be measured and paid separately)iii) Poise Plain Acrylic Bathtub (Drop-in) C871246V(1700 x 750 mm) including Automatic Pop-upWaste and Self-draining System (C871899), BaseMetal Frame (C871746) |
219 | BATH TUB MIXER: Supplying, fitting and fixing Chrome Plated (C.P.) Bath tub mixer with telephone shower arrangement only and crutch 20mm of Essco make complete as directed. Cat No.1180 |
220 | PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISIapproved including joining, fitting and fixing with clamps etc.as necessary completeat all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia. |
221 | PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISIapproved including joining, fitting and fixing with clamps etc.as necessary completeat all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches.(ii) 110mm dia. |
222 | PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISIapproved including joining, fitting and fixing with clamps etc.as necessary completeat all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (iv) 75mm dia. |
223 | PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISIapproved including joining, fitting and fixing with clamps etc.as necessary completeat all levels including below G.L as directed and specified.b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 110mm dia. |
224 | PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISIapproved including joining, fitting and fixing with clamps etc.as necessary completeat all levels including below G.L as directed and specified.b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (iv) 75mm dia. |
225 | Supplying, fitting and fixing 87.5 degree PVC bend of(Supreme/Prince) or other ISIapproved including joining ,fitting and fixingetc.as necessary completeat all levels including below G.L as directed and specified.a) In exposed surfaces or in trenches.(i) 160mm dia. |
226 | Supplying, fitting and fixing 87.5 degree PVC bend of(Supreme/Prince) or other ISIapproved including joining ,fitting and fixingetc.as necessary completeat all levels including below G.L as directed and specified.a) In exposed surfaces or in trenches.(ii) 110mm dia. |
227 | Supplying, fitting and fixing 87.5 degree PVC bend of(Supreme/Prince) or other ISIapproved including joining ,fitting and fixingetc.as necessary completeat all levels including below G.L as directed and specified.a) In exposed surfaces or in trenches. (iv) 75 mm dia. |
228 | Supplying, fitting and fixing 87.5 degree PVC bend of(Supreme/Prince) or other ISIapproved including joining ,fitting and fixingetc.as necessary completeat all levels including below G.L as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 110mm dia. |
229 | Supplying, fitting and fixing 87.5 degree PVC bend of(Supreme/Prince) or other ISIapproved including joining ,fitting and fixingetc.as necessary completeat all levels including below G.L as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (iv) 75 mm dia. |
230 | Supplying fiting and fixing 87.5 degree PVC bendwith doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches.(i) 160mm dia. |
231 | Supplying fiting and fixing 87.5 degree PVC bendwith doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches.(ii) 110mm dia. |
232 | Supplying fiting and fixing 87.5 degree PVC bendwith doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches.(iv) 75 mm dia. |
233 | Supplying fiting and fixing45 degree PVC bend of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches.(i) 160mm dia. |
234 | Supplying fiting and fixing45 degree PVC bend of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches.(ii) 110mm dia. |
235 | Supplying fiting and fixing45 degree PVC bend of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches.(iv) 75 mm dia. |
236 | Supplying fiting and fixing45 degree PVC bend of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified.b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages.(ii) 110mm dia. |
237 | Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches(i) 160mm dia.. |
238 | Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches (ii) 110mm dia. |
239 | Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages.(ii) 110mm dia. |
240 | Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages (iv) 75 mm dia. |
241 | Supplying fiting and fixing PVCsingle tee with door of(Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia. |
242 | Supplying fiting and fixing PVCsingle tee with door of(Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia. |
243 | Supplying fiting and fixing PVCsingle tee with door of(Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches (iv) 75 mm dia. |
244 | Supplying fiting and fixing PVCsingle tee with door of(Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages.(ii) 110mm dia. |
245 | Supplying fiting and fixing PVCsingle tee with door of(Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages (iv) 75 mm dia. |
246 | Supplying fiting and fixing PVCsingle ‘Y’ of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches.(i) 160mm dia. |
247 | Supplying fiting and fixing PVCsingle ‘Y’ of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches (ii) 110mm dia. |
248 | Supplying fiting and fixing PVCsingle ‘Y’ of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified a) In exposed surfaces or in trenches (iv) 75 mm dia. |
249 | Supplying fiting and fixing PVCsingle ‘Y’ of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages(ii) 110mm dia. |
250 | Supplying fiting and fixing PVCsingle ‘Y’ of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages (iv) 75 mm dia. |
251 | Supplying fiting and fixing PVCsingle ‘Y’ with door of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches (i) 110mm dia. |
252 | Supplying fiting and fixing PVCsingle ‘Y’ with door of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches (ii) 75 mm dia. |
253 | Supplying fiting and fixing PVCsingle ‘Y’ with door of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages (i) 110mm dia.. |
254 | Supplying fiting and fixing PVCsingle ‘Y’ with door of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages(ii) 75 mm dia. |
255 | Supplying fiting and fixing PVC double‘Y’ plain of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 75 mm dia. |
256 | Supplying fiting and fixing PVC double‘Y’ plain of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified.b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (i) 110mm dia. |
257 | Supplying fiting and fixing PVC double‘Y’ plain of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified.b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages.(ii) 75 mm dia. |
258 | Supplying fiting and fixing PVC cross ‘T’ with doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm x110mm |
259 | Supplying fiting and fixing PVC cross ‘T’ with doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified a) In exposed surfaces or in trenches.(ii) 75 mm x 75mm |
260 | Supplying fiting and fixing PVC cross ‘T’ with doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages.(i) 110mm x110mm |
261 | Supplying fiting and fixing PVC cross ‘T’ with doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages (ii) 75 mm x 75mm |
262 | Supplying fiting and fixing PVC coupler of (Supreme/ Prince)or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches.(i) 110 mm dia |
263 | Supplying fiting and fixing PVC coupler of (Supreme/ Prince)or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iii) 75 mm dia |
264 | Supplying fiting and fixing PVC coupler of (Supreme/ Prince)or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (i) 110 mm dia |
265 | Supplying fiting and fixing PVC coupler of (Supreme/ Prince)or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages.(iii) 75 mm dia |
266 | Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160 mm x 110 mm |
267 | Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 110 mm x 75mm |
268 | Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. in exposed surface or trencesas necessary complete at all levels including below G.L. as directed and specified.(a) 110 mm |
269 | Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. in exposed surface or trencesas necessary complete at all levels including below G.L. as directed and specified (b) 75 mm |
270 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall15 mm nominal dia. Pipes. |
271 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall20 mm nominal dia. Pipes. |
272 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall25 mm nominal dia. Pipes. |
273 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall32 mm nominal dia. Pipes. |
274 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall40 mm nominal dia. Pipes. |
275 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall50 mm nominal dia. Pipes. |
276 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. : Concealed work, including cutting chases and making good the walls etc.15 mm nominal dia Pipes |
277 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. : Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes |
278 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia. Pipes. |
279 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. : Concealed work, including cutting chases and making good the walls etc 32 mm nominal dia. Pipes. |
280 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore |
281 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete25 mm nominal bore |
282 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore |
283 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore |
284 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore. |
285 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore |
286 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore |
287 | Supply installation, testing and commissioning of borewll submersible pump with necessary pipes, fittings, electrical connections and accessories for lifting of water from a depth of 100m (depending on the water level availabilty under the ground) with flow rate at 720 LPM (for three hours of Running) one working one standby |
288 | Supply installation testing and commissioning of centrifugal pump (submersible/vertical/horizontal pump) of flow rate 220 LPM @ 50m head for block A(One working and one standby) |
289 | Supply installation testing and commissioning of centrifugal pump (submersible/vertical/horizontal pump) of flow rate 400 LPM @ 60m head for block B (One working and one standby) |
290 | Supplying, fitting and fixing Kitchen chimney including water proof ply board, plain sheet, decorative prelaminated sheet, nail, fevicol, dendrite, wooden beading etc.as required complete as specified and directed by the department. |
291 | Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes:(a)Sintex make : i)2000 Lt capacity |
292 | Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes:(a)Sintex make :ii) 1000 litre capacity |
293 | INTERIOR WORKS:GYPSUM CEILING :Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
294 | SOFT CEILING AND CLADDING SYSTEM: Supplying and installation of water proof, non-VOC emission, seamless post installation, teMetreite and rust proof PVC ceiling of panel of size not less than 3060 x 300 mm fixed in a frame work of J and T profile of size not less than 3060 x 22 and 3060 x 42 accordingly. The profile framework should fix rigidly with the wall/ roof with necessary arrangements like screws, nails, drop bars etc. Prior approval should be obtained before finalization of the colour and texture of the panels. Necessary cutting/ provisions should be kept for fixing light fixtures (surface mounted or recessed type) without damaging the seamless look of the ceiling/ wall cladding. Including necessary side beading, joint filler etc. and complete in all respect as per the specification and instruction of Engineer in Charge. |
295 | WALL PANELLING WITH CONCEALED METAL (G.I. SECTION) FRAMEWORK: Providingand fixing concealed G.I. sections for wall lining with Everest Non-AsbestosFibre Cement Board confirmingIS–14862,whichincludes6mmplain board(for dry area) / 6mm designer board ( Lake & Hill, Oceanic, Casecade, Electra) / 6mm Heavy Duty plain board(for wet area) of M/SEverest Ltd., fixed on the ceiling section (0.55mm thick having a knuled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm made of G.I. steel) placed at 610mm center in perimeter channel (0.55mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm made of G.I.steel) fixed to the floor and ceiling with nylon sleeves & wood screws at 610mm c/c with fully threaded self-tapping screws all complete as per the drawing & directions of Engineer- in-charge The boards may be finished so as to have a uniform groovefinishedwithexpansionfiller. Alternatively, grooves/jointscanbecoveredwithdecorative molding/jointing compounds to have a uniform flush finish. Finally, if specified, the boards can be painted with 2 coats of acrylic emulsion paint of approved shade over a coat of cement primer. 6 mmEverest Designer FC board |
296 | LAMINATES: Supplying designing and laying 1.5 mm thk. laminates of approved shade and colour of recomanded brandon door or any other vertical and horizontal, wall and ceiling(ply, cement board, MDF, WPC) surface to be decorated as per approved drawing and view to obtain the desired architectural element. Necessary SS bead of 10 to 12 mm wide and required thickness to be fixed as per the design with high perfomance adhesive, concealed screw etc. the laminated surface should be finished with 40:60 PU polish from repued brand like Asian, Berger ect. Incluing necessary scaffolding finished and complete as per instruction of Engineer in charge. |
297 | VENEER: Supplying designing and laying 4mm thk. Veneer of approved shade and colour of recomanded brandon door or any other vertical and horizontal, wall and ceiling(ply, cement board, MDF, WPC) surface to be decorated as per approved drawing and view to obtain the desired architectural element. Necessary SS bead of 10 to 12 mm wide and required thickness to be fixed as per the design with high perfomance adhesive, concealed screw etc. the veneered surface should be finished with 40:60 PU polish from repued brand like Asian, Berger ect. Incluing necessary scaffolding finished and complete as per instruction of Engineer in charge. |
298 | WALL PANELLING/ FALSE CEILING WITH WATER PROOF PLY: Providing and fixing water proof ply wood board ( aproved brand) 6 mm, 12 mm and 19mm where applicable for wall panelling works as per approved design and drawing with required wooden or ply board supprt frame includingnecessary 10 to 12 wide SS bead, nail, screw, adhesives and complete as per instruction of engineer in charge. (The wall paneling shall be finished with 1.5 mm thick laminates, PU polished 4 mm thick veneer, wall paper, texture paints which will be measured and paid extra.) |
299 | BAMBOO WOOD WALL CLADDING:Providing & fixing in position Phenol bonded Bamboo Wood Wall Cladding at all height with planks of sizes 10mm thick, 100 mm minimum width and of required length as per the Architectural design. The plank made out of Eco friendly Bamboowood of ESES or equivalent brand (made in India ) withnecessaryprofilededges;placedon walls. The bamboo wood planks shall have minimum density of 1000 kg/cum & minimum Hardness 1000 Kgf. Bamboowood panels and frame all held in place as per manufacturers design details. Including necessary concealed screws, nails and other accesories required to fix the planks in position either existing frame work or other flat surface like ply, cement board. (frame work or surface will be measured and paid separately)and finished to smooth as complete wall cladding as per direction of Engineer in-charge. |
300 | FLUSH DOOR: Providingandfixingflushdoorshutterssolidcore construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including 4 numbers SS hingesof size: 100 X 75 X 3 mm having 2 high perfomance ball bearing (refer: Hafele article no. 926.32.160) from reputed brand like Hettic, Hafele, Godrej etc. with necessary recomended screws. The edges of the door should be covered with a hard wood timber bead of required width and 6mm thick to be finished with 40:60 PU polish. Decorative type face panel and block board core. 35 mm thick. (The flush door shall be finished with 1.5 mm thick laminates, PU polished 4 mm thick veneer or mirrior where applicable and same will measured and paid extra.) |
301 | WOODEN FLOORING: Providing,fittingandfixingsolid wood woodenflooringfrom reputed brand like Uniproducts (India) Ltd./ Armstrong of thickness 14mm madeofpurewood(EngineeredWood)ofdifferent types with a top layer of 3mm thick hard wood and Under layer of 2mm thickness made of polythene and foamsheet laid on existing concrete/tiles floor complete as directed and specified. |
302 | TOILET FLOOR TILES Providing and laying Vitrified tiles in floor in different sizes (thickness tobe specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size 11.41A.3.1 Size of Tile 600 x 600 mm |
303 | VITRIFIED FLOOR TILES :Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 1000x1000 mm |
304 | VITRIFIED FLOOR TILES :A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.:Size of Tile 1000 x 1000 mm |
305 | WALL TILES ( TOILET/ KITCHEN ): Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete. |
306 | WOOD WORK: ( DOOR , WINDOW AND TRUSS ):Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).: Sal wood |
307 | DOOR / WINDOW SHUTTER): Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately): 35 mm thick shutters |
308 | Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured). |
309 | FLOAT GLASS PANES : 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm) |
310 | WOODEN BEAD FOR DOOR AND WINDOW: Providing and fixing wooden moulded beading to door and window frameswith iron screws, plugs and priming coat on unexposed surface etc.complete : 50x12 mm |
311 | WOODEN BEAD FOR DOOR AND WINDOW: Providing and fixing wooden moulded beading to door and window frameswith iron screws, plugs and priming coat on unexposed surface etc.complete : 50 x 20 mm |
312 | RAILING / BALUSTRADE :Providing and fixing wooden 100mmx 60mm rounded hand rails in straight lengths complete.(a) With 1st class Teak wood / Sissu wood |
313 | Providingandfixing25mmx25mmfirstclasstimber balustrade25mmx25mmsquare,wroughtfixedwith endshoused(squareorsplayed)tohandrailsand trends or strips complete.: (a) With 1st class Teak wood / Sissu wood |
314 | OPENABLE GLASS DOOR/ FIXED GLASS: Supplying materials and installation of frame less glass partition with 12 mm thick toughened glass as per the Architectural drawing and design,including all necessary stainless steel glass architectural hardwareand necessary framework above ceiling to support glass hardwareto fix the partition rigidly at it"s position. Necessary hardware, fitting and fixtures for doors should be of recommended brand like Dorma, godrej or equivalent. Installation of floor spring, door closer, door handle (H-type back to back; 400mm-500mm overall length), sensor control etc. are included and should also be from approved manufacturer and compatible with the weight of the door (Manufacturer recommendation necessary). The fixing and lifting of glass of required width/length is the sole responsibility of the contractor. Including all other supporting items like silicon based adhesives, locking arrangements if any and complete as per the directions of Engineer In-charge. a) Full height glass partition with openable door. |
315 | GLASS FILM / GLASS PAPER : Supplying and installation of good quality commercial Glass film/ Glass paper from brand having good market track record over last five years, of approved colour, pattern and design (where applicable) and fixed with proper adhesive. The joints of Glass film/ Glass paper should not be visible in any case. Complete and finished in all respect and as per the directions of Engineer in-charge. (Minimum MRP of the product should not be less than Rs. 1000.00 per Sqm) only |
316 | CUP BOARD: Providing and fixing wall fixed cupboard as per the following specification Inner body: Inner body of the cupboard should be made out of WPC (Wood Polymer Composite) solid plain white colour board comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing to the smooth wall surface finished with wall putty and two coats of cement primer. The shelves and drawers are planned as per the requirement to keep clothes and other belongings of residential use. All the exposed edges are to be finished with 2mm thick 16 to 19mm wide PVC/paper edge binding of approved quality including necessary synthetic resin hot pressed to edges on binding machine having property of providing uniform and integrated look. The inside top surfaces of the WPC boards are to be finished with plastic/ acrylic laminates of min 1.00 mm thick. Measurement will taken on the front area i.e. Height X Width of the cupboard. Depth of the cupboard will not be considered for measurement in any case. Accessories:Accessories like drawer slider, rob hock, hanger bar, trouser pull, door handle out etc. complete; should be of SS mat finished and from approved brand like Hafele, Hettic, Godrej or equivalent. Sliding front door track (where applicable) should be of sound less, aluminum made channel as preapproval of the authority. A digital safe deposit vault of 300mmX300mm is to be fixed where applicable (the vault will be measured and paid separately). All locking arrangement should be hassle free and product should be from reputed brand like Hafele, Godrej or equivalent. Handles, nobs etc. should not have any sharp edge/ corner and should be from reputed bran like Hafele, Godrej, Ozon or equivalent. Including all required ball bearing and other accessories to make the wall unit user friendly. Wardrop rails should be from reputed brand like Hettich, Hafele of matching colour. Quated rate should be inclusive of both the cubical and accesories. |
317 | PLY MADE CUP BOARD DOOR / PALLA :Door made out of 19 mm thick approved quality water proof ply finished internal surfaces with 1.5 mm thick laminates (white in colour) of approved designed, shade and brand fixed with approved adhesive. The edges of the ply board should be covered with 6 mm thick wooden bead finished with 40: 60 PU polish. The exterior surface of the door should be finished with 4 mm thick veneer board approved colour and shade from reputed brand fixed with approved adhesive.Includingcounter sung screw, 125 mm SS mat finished cupboard handle, nobs locking armament etc. should be from reputed brand like Hafele, Hettic, Godrej or equivalent. Probable Cut, grove, double layer veneer of different shade etc. are to be considered while quoting the rate. The veneer surfaces are to be finished with 40: 60 PU polish. Finished and complete as per instruction of engineer in charge. |
318 | PARTICLEBOARD CUP BOARD PALLA:Door made out of both side laminated (inner side white and outer side of approved shade) 19 mm thick particle board from reputed brand approved by the authority to be fixed to the existing WPC cupboard body fixed with smooth closing concealed hinge 110 degree opening angle side-on hinges with automatic closing spring, with 3dementional adjusting facilities fit for 19 mm thick door. Including Providing and fixing 2mm thick 19mm wide PVC/paper edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine, counter sung screw, 125 mm SS mat finished cupboard handle, nobs locking armament etc. should be from reputed brand like Ozone, Dorma or equivalent. Finished and complete in all respect as per the instruction of engineer in charge. |
319 | ALUMINIUM CUP BOARD SHUTTER:Providing and fixing Klar Door from reputed manufacturer like Hettich, Hafele, or equivalent with Klar Door Hinges especially designed in slim form, hinge enables soft closing of the door for silent operation equipped with a soft closing mechanism ensuring silent closing of cabinet doors making way for peaceful operation with approved frame colour (Brushed Stainless Steel, Brushed Black Material) with minimum profile thickness 19.2 mm and weight not less 0.60 kg/meter.Clear float glass, Milky white , mirror or any other coloured glass as per the approval of the authority of thickness 4-5 mm. Glass cabinet doors complete with PVC black finished C shaped gasket for 5 mm glass, filler gasket for 4 mm glass, Corner Connector Countersunk Screws etc. All fixtures should design to withstand an overall weight of the shutter (glass and profiles) should be 20 kg. |
320 | MARBLE TOP CUPBOARD:Cupboard, body made out of WPC (Wood Polymer Composite) solid plain white colour board comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing to the smooth wall surface finished with wall putty and two coats of cement primer. The shelves and drawers are planned as per the requirement to keep pantry equipment and other belongings of residential use. All the exposed edge are to be finished with 2mm thick 16 to 19mm wide PVC/paper edge binding of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine having property of providing uniform and integrated look. The inside top surfaces of the WPC boards are to be finished with plastic/ acrylic laminates of min 1.00 mm thick. Top and side visible surfaces are to be finished with good quality mirror polished Italian marble with beveled cutting. Measurement will taken on the front area i.e. Height X Width of the cupboard. Depth of the cupboard will not be considered for measurement in any case. Accessories:Accessories like drawer slider, rob hock, hanger bar, trouser pull, door handle out etc. complete; should be of SS and from approved brand like Hafele, Hettic, Godrej or equivalent. Sliding front door track (where applicable) should be of sound less, aluminum made channel as from approved brand like Hafele, Hettic, Godrej or equivalent preapproval of the authority. A digital safe deposit vault of 300mmX300mm is to be fixed where applicable (the vault will be measured and paid separately). All locking arrangement should be hassle free and product should be from reputed brand like Godrej, Ozone or equivalent. Handles, nobs etc. should not have any sharp edge/ corner and should be from reputed bran like Godrej, Ozon or equivalent. Including all required ball bearing and other accessories to make the wall unit user friendly. Wardrop rails should be from reputed brand like Hettich, Hafele of matching colour. Quated rate should be inclusive of both the cubical and accesories. |
321 | WALL UNIT (for TV, bed side table, pantry etc.): Providing and fixing designed wall unit made out of 6 to 19 mm thick approved quality water proof ply finished all the exposed surface with 1.5 mm thick laminates of approved designed, shade and brand including SS bead of 10 to 12 mm wide to be fixed flush with the final surface and wooden bead of required size where applicable. the design require nice cut (depresion) and projection wich are to be finished with matching coloured lamintes 1.5 mm thick of approved colour , shade and brand. The wooden beads are to be finished with 40: 60 PU polish and complete as per instruction of engineer in charge. (measurement will be taken on flat area : width X height) |
322 | RECEPTION COUNTER: All inner surfaces to be finished with off white colour 1.5 mm thick good quality laminates from reputed approved brand fixed with approved adhesive. Exposed edges of boards are to be finished with 6 mm thick timber bead of required width finished with 40: 60 PU polish/ Duco paints (where applicable).The two tier counter top (work station for staff and comfort standing for visitor) surfacesare to be finished with Italian marble of approved quality and shade, 4mm thick veneer finished with 40: 60 PU polish, Duco paint (where applicable). The probable size of the counter is 5.40 M long, 1.20M high. Including necessary slider channels for drawers, handle, nobs, locks etc. from reputed brand like Hafele, Hettic, Godrej etc. Finished and complete in all respect as per the instruction of engineer in charge. |
323 | LOUVER :Providing 1st class local wood (Hollock/ Bonsum)ventilatinglouvrein50mmx38mmsize wooden frame with 150mm x 20mm slate made of 1st class local wood including fitting and fixing with nails and painting with two coats of kiricide oiling complete. With Teak wood/Sissu wood. |
324 | LOUVER :Providing 1st class local wood (Hollock/ Bonsum)ventilatinglouvrein50mmx38mmsize wooden frame with 150mm x 20mm slate made of 1st class local wood including fitting and fixing with nails and painting with two coats of kiricide oiling complete. With Teak wood/Sissu wood. |
325 | MEETING TABLE: Supplying materials and making table on site or at factory as per the approved drawing and specifications. The specifications of materials and construction methodology will be as follows: Top: Making table top with 16 mm thick high pressure interior compact Laminate made out of thermosetting resign treated kraft as core material and design paper as a finish surface with lining on the edges. The border of the top should be double layered to get 32 mm thick as per the approved drawing and design. The material should be flame retardant as per BS-476/97 and EN438-6 withclassification ofBS1D0 standard property, anti-bacterial and anti-termite property under JIS Z2801:2000. It should have resistance to scratch, fire and weather. For bigger size table, necessary arrangement should be made to assemble/ de-assemble the top. Special care should be taken to get smooth and elegant look and there should not be any sharp corner. Colour and edge lining will be as per the view and instruction of the Engineer –in-charge. (The measurements will be taken on finished size of the top of table and side table, in any case height, depth etc. will not be considered for measurement) Side and others: The side, supporting frame, drawer, shelve, tray etc. made with premium quality prelaminated board of approved colour and brand of 8 mm to 18 mm thick (where applicable) with all necessary hardware and fittings like drawer channel, lock, nob, handle, lift-up, vertical and horizontal slider etc.(where applicable) of approved manufacturer to complete the table as per the drawings and design. Provision for grommet (table cord wire manager) of approved quality (due approval has to be obtained from the Architect/ Department) is to be kept as per need and utility. All necessary installation (where applicable) of power and telephone sockets, switches, speaker, audio system etc. are included ( socket, switch, speaker & audio system will be measured and paid separately). Finished and complete in all respect as per the instruction of Engineer In Charge. Meeting Table for 6 persons : |
326 | PIN UP BOARD:Supplying and fixing in position High tear-strength Flocked Fabric (Velvet) Surface warp-free, smell-free and corrosion-free pin-up board of reputed brand having market existence of at least five years and good track record framed with heavy anodised aluminium channels and chrome plated corners of 1800mmX 1200mm . The board should have high-density Soft Board Core to ensures documents stay securely pinned at all times and resists hole formations even after multiple pinnings. Inclusive of Built-in ABS wall hangers to allow hassle-free mounting of the board in portrait as well as landscape orientation. Complete with all hardware for installationas per the direction of Engineer In Charge. Minimum MRP of the product should not be less than Rs.2,000.00 (Rupees Two thousand) only. |
327 | DUCO PAINT: Providing and applying in 3 or more coats lacquer paint of "DUCO" or equivalent make and approved shade over metallic surfaces / wood and other surfaces after preparing the surface with good quality water proof putty to get proper surfaces, applying necessary coats of primer and finishing with matt / textured finish laquer paint. All complete as per detail drawing, as specified and as directed by Architect / Consultant / Project - In - Charge. |
328 | FIVE SEATERSOFA SET :Supplying premium category sofa made of solid wood combination of ethnic and contemporary style, PVC upholstery in brown shade and prominentstitching lines along with soft foam cushion seats. The armrest and frame in square form finished in cappuccino shade. The sofa set should be designed to optimum use of space and easy to maintain. Including matching centre table made of MDF top and rubber wood understructure finished with cappuccino shade. Load bearing capacity should not be less than 25 kg. Complete in all respect and finished as per instruction of Engineer-in-charge. 1.Single-Seater (2 nos.) : 2.Three-Seater (1 no.) : 3.Centre-table (1 no.): Godrej model :Encardo (3+1+1) with Splenda centre table Featherlite model : 238-1S PEARL (Single Seater Leatherette Sofa - 2 nos.), 238-3S PEARL(Three Seater Leatherette Sofa - 1 no.), 610-FL (Rectangular table - 1 no.) Wipro model : Alysia 1 Seater Leathertte, Alysia 3 Seater Leathertte |
329 | SINGLE SEATER SOFA: Supplying and placing In position wooden framed single sitter sofa, S.S leg, leatherette seat cover above high density foam cushion from reputed brand like Godrej, feather light or equivalent. Minimum side of the sofa should not be less than : 715x750x725mm. |
330 | TWO SEATERSOFA: Supplying and placing In position wooden framed three sitter sofa, S.S leg, leatherette seat cover above high density foam cushion from reputed brand like Godrej, feather light or equivalent. Minimum side of the sofa should not be less than : 1950x750x725mm. |
331 | CORNER ADJUSTING SOFA: LHS Sectiona sofa Supplying and placing In position wooden framed tLHS Sectiona sofa, S.S leg, leatherette seat cover above high density foam cushion from reputed brand like Godrej, feather light or equivalent. Minimum side of the sofa |
332 | UTILITY RACK :Supplying materials and making a utility rack on site as per the approved drawing and specifications. The specifications of materials and construction methodology will be as follows: Making rack with 19 mm thick ply board finished with laminate as specified. The material should be flame retardant as per BS-476/97 and EN438-6 with classification ofBS1D0 standard property. Finished and complete as per the specifications, drawings and instruction of the Engineer-in-charge. |
333 | STUDY CHAIR: Medium back chair, PU adjustable arm, Synchro Tilt, Gas Lift, Nylon Base, Mesh Back |
334 | ROUND DINING TABLE( 4 seater ) Supplying4 seater knock down style , 1200 mm dia and 750mm heightround dining table , table top made of tempered glass of thickness not less than 12mm with bevelled edge and moulding havingwith chrome finished legs as shown in the reference image( Please check the refer image enclosed) |
335 | SQUARE /RECTANGULAR DINING TABLE( 4 seater ) FOR RESTAURANT Supplying4 seater knock down style , 1200 mmX1200 mm and 750mm heightdining table , table top made of tempered glass of thickness not less than 12mm with bevelled edge and moulding havingwith chrome finished legs as per direction of Engineer - in charge. |
336 | BATH ROOM MIRROR: Providing fitting and fixing 716mm Diameter Round Shape Mirror from KOHLER Essential mirror collection of approved soft silhouettes. |
337 | CURTAIN: Supplying fitting and fixing of window/ door curtain of approved colour, texture and pattern stitched to the size of the opening including required extension in length and width. Prior approval should be obtained to finalize the design and pattern. The cloth (Material) should be of Polyester having minimum thread Count: 220 and GSM:299 and of normal machine washable in cold water. Including required aluminum based curtain rod suitable for office interior along with necessary accessories for fixing the same in position. Finished and complete in all respect as per the direction of the Engineer In Charge. The basic price of the curtain material should not be less than Rs.1200.00 (Rupees one thousand two hundred) only per meter for 1.20 M wide cloth and for curtain rod basic price should not be less than Rs.300.00 (Rupees three hundred) only per meter. |
338 | NET CURTAIN:Supplying fitting and fixing of net curtain of approved colour, texture and pattern stitched to the size of the opening including required extension in length and width. Prior approval should be obtained to finalize the design and pattern. The cloth (Material) should be of Polyester having minimum thread Count: 220 and GSM:299 and of normal machine washable in cold water. Finished and complete in all respect as per the direction of the Engineer In Charge. |
339 | MINI FRIDGE: Supplying installation and commissioning of 30 lit. cubical type mini fridge of approved colour from reputed brand like Godrej, Panasonic, Samsung orequivalent.within existing cupboard |
340 | LOCKER: Supplying installation testing and commissioning Godrej NX Pro Digital 15L Home Locker Ebony of approved colour. |
341 | AUDIOAND VISUAL DISPLAY SYSTEM FOR DINING HALL : Supplying, installation testing and commissioning ofDining hall audio and visual display system as per the specifications enclosed as Annexure -I |
342 | AUDIO AND VISUAL DISPLAY SYSTEM AT MEETING HALL: Supplying, installation testing and commissioning of Meeting hall audio and visual display system as per the specifications enclosed as Annexure II |
343 | Mid Back Chairs for visitors, meeting and other Minimum Features : 1.Height adjustable back. 2.Height adjustable arms. 3.Seat depth adjustment. 4.Active bio-synchro mechanism. Equivalent to Godrej model :Marvel Mid-back Featherlite model : Opus Mid-back Wipro model : Adapt Mid-back |
344 | HIGH BACK CHAIR:Chrome Base High Back Chair: Multilock Mechanism :Gaslift & Two Way Adjustable Arms(Height&Swivel)withChromeBase- Leatherette Seat & Back |
345 | STORAGE UNIT: Supplying and fixing in position storage units/ cabinets/ racks etc. made with premium quality prelaminated board of approved colour and brand of 8 mm to 18 mm thick (where applicable) with all necessary hardware and fittings like drawer channel, lock, nob, handle, lift-up, vertical and horizontal slider etc.(where applicable) of approved manufacturer to complete the storage units/cabinets as per the drawings and design. The side, supporting frame, drawer, shelve, tray etc. should be rigid to resist the required load. The size and shape of the storage unit/cabinet should be as per approved enclosed drawings. All materials should fulfill the norms of IS 2046(Indian Standard). or equivalent international code. Green Guard Certified product is preferable in any case.Including fixing in position and finished in all respect as per the instructions of Engineer In Charge. (Depth of the storage unit/cabinet may vary in between 450 mm to 600 mm and for measurement in Sqm, length and height of the storage unit/cabinet will be considered) |
346 | STUDY TABLE: Supplying and fixinf in position Designer table width not more than 750 mm and length not mor than 1800 mm ( according to the availabilty of space) made out of 6 to 19 mm ply and MDF board finished with 4 mm thick approved coloured40:60 PU polished veneer. The border of the top should be multilayered to get 50 mm thickness. Necessary wooden bead, finished with 40: 60 PU polish should be used where necessary. A drawer width not less than 450 mm and side shelf below the drawer of equal depth with ply/MDF board palla finished with 40:60 PU polish 4 mm thick veneer. All hardware used for drawer, handle, nobetc. should be SS mat finish from reputed brand like Hettic, Hafele, Godrej or equivalent. Finished and complete as per drawing and design and instruction of engineer in charge. |
347 | TABLE FOR BAR ::Supplyingfourseatertable made of reputed make of single pole supported,circularin shape and size not less than 750mm dia. height not less than 650 to 750mm.The s.s make base plate of the table should have sufficient weightto keep the balance on tiles/ marble etc. flooring. The top should be of exterior grade rigid compact laminate board of thickness not less than 12mm of approved colour and shade Authority may opt for tempered glass top also. ( Please check the refer image enclosed) |
348 | CHAIR: Supplying cafeteria stakable chair from reputed make with polypropylene seat & back of approved colour and legs s.s / chrome finished. The height of the chair should not be less than 700mm and arrangement of legs are suitable to stake one above another ( Please check the refer image enclosed) |
349 | BAR stakable chair: Supplying cafeteria stakable chair from reputed make with polypropylene seat & back of approved colour and legs s.s / chrome finished. The height of the chair should not be less than 700mm and arrangement of legs are suitable to stake one above another ( Please check the refer image enclosed) |
350 | SINGLE BED for SECURITY Including mattress: Supplying and fixing in position Single size bed with head board and side and rear grip for 150 mm thick mattress made out of good quality pre-laminated particle board, ply board of required thickness. Height of the bed should not be less than 350 mm and there should be a head board of at least 450 mm above the mattress. 2mm thick 16 to 19mm wide PVC edge binding tape of approved quality with necessary synthetic resin hot pressed to edges on binding machine. Including necessary MS clamp concealed/ counter sung screw etc. and 150mm pocket spirng HD foam based mattress fro reputed brand brand like Kurlon, Sleepwell or equivelent.finished and complete as instructed. |
351 | KING SIZE BED : Supplying and fixinf in position King size bed with head board and side and rear grip for 150 mm thick mattress made out of good quality pre-laminated particle board, ply board of required thickness. Height of the bed should not be less than 350 mm and there should be a head board of at least 450 mm above the mattress. 2mm thick 16 to 19mm wide PVC edge binding tape of approved quality with necessary synthetic resin hot pressed to edges on binding machine. Including necessary MS clamp concealed/ counter sung screw etc. and finished and complete as instructed. |
352 | MATTRESS: Supplying and fixing in position 250mm pocket spirng HD foam based mattress fro reputed brand brand like Kurlon, Sleepwell or equivelent. |
353 | CENTER TABLE: Sofa center table round and rectangular shape (600 dia or 1200 X 600 mm)Top&Sides made out of25mm Thickpre-laminatedparticle board height not more than 600 mm or as per manufacturer like Godrej, Feather light, Geeken etc. The under structure made out of 50 mm dia MS power coated leg with necessary lever, rubber buffer. |
354 | GAZEBO: Supplying materials installation with proper finishing as per architectural drawingand comapny installation manual. Roof shringles(approved brand colour & texture) of 0.3m thick over 12mm thick water proof plyboard in two crossed layers as per roof and barge board design if any. On bamboo purlins/truss of roofing member tied with necessary screws,nails,bolts,anchor bolts where applicable. A water proofing membrane is to be applied on plyboard surface before placing the shringles. All the ridge/valley are to be covered with nea arrangement to give in integrated look of the structure including primer/paint in either sides of the roof and barge board.(will be measured and paid separately). Finished and complete as per specification/company manual and instruction of Engineer incharge. |
355 | FRP GRATING :Providing, fitting and fixing moulded FRP grating with chequered plate for covering drains all complete as directed by Engineer-in-charge.a) Mesh size - 38X38 MM, Thickness - 30 MM |
356 | FRP GRATING MANHOLE"Providing, fitting and fixing moulded FRP grating manhole with chequered plate for covering drain/ openings all complete as directed by Engineer-in-charge.a) Mesh size - 38X38 MM, Thickness - 30 MM |
357 | CHANNEL FOR CURTAIN: Supplying, fitting and fixing wall mounted aluminium soundless channel for curtains. |
358 | WPC DOOR FRAME Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shallbe paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made:Frame size 65 x 100 mm |
359 | UPVC: Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foMetreing process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) |
360 | UPVC:Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foMetreing process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
361 | UPVC:Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foMetreing process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes,wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.) |
362 | UPVC :Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foMetreing process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) |
363 | Providing and fixing steel roller for uPVC sliding door with necessary screws etc. complete. |
364 | Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete. |
365 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
366 | SHOWER CUBICAL : Supplying materials and installation of shower cubical with 8 mm thick toughened glass as per the Architectural drawing and design,including all necessary stainless steel glass architectural hardwareand necessary framework to fix the partition rigidly at it"s position. The provision of door is to be kept according to the Architectural design need. Necessary hardware, fitting and fixtures should be mat/gloss finished SS 304 and from recommended brand like Dorma, Godrej etc. Installation of towel bar of 25 mm dia, 450 mm, 200 mm long (reference: hafele article no. 980.47.000) included and should also be from approved manufacturer and compatible with the weight of the door (Manufacturer recommendation necessary). The fixing and lifting of glass of required width/length is the sole responsibility of the contractor. Including all other supporting items like water sealed transperant pvc rubber guskae, silicon based adhesives and complete as per the directions of Engineer In-charge. : a) 1250mm x 1250mm |
367 | SHOWER CUBICAL : Supplying materials and installation of shower cubical with 8 mm thick toughened glass as per the Architectural drawing and design,including all necessary stainless steel glass architectural hardwareand necessary framework to fix the partition rigidly at it"s position. The provision of door is to be kept according to the Architectural design need. Necessary hardware, fitting and fixtures should be mat/gloss finished SS 304 and from recommended brand like Dorma, Godrej etc. Installation of towel bar of 25 mm dia, 450 mm, 200 mm long (reference: hafele article no. 980.47.000) included and should also be from approved manufacturer and compatible with the weight of the door (Manufacturer recommendation necessary). The fixing and lifting of glass of required width/length is the sole responsibility of the contractor. Including all other supporting items like water sealed transperant pvc rubber guskae, silicon based adhesives and complete as per the directions of Engineer In-charge.: b) 1350mm x 1200mm |
368 | SHOWER CUBICAL : Supplying materials and installation of shower cubical with 8 mm thick toughened glass as per the Architectural drawing and design,including all necessary stainless steel glass architectural hardwareand necessary framework to fix the partition rigidly at it"s position. The provision of door is to be kept according to the Architectural design need. Necessary hardware, fitting and fixtures should be mat/gloss finished SS 304 and from recommended brand like Dorma, Godrej etc. Installation of towel bar of 25 mm dia, 450 mm, 200 mm long (reference: hafele article no. 980.47.000) included and should also be from approved manufacturer and compatible with the weight of the door (Manufacturer recommendation necessary). The fixing and lifting of glass of required width/length is the sole responsibility of the contractor. Including all other supporting items like water sealed transperant pvc rubber guskae, silicon based adhesives and complete as per the directions of Engineer In-charge.: c)800mm X 900mm |
369 | STEAM BATH: Supplying materials, installation, testing and commissioning of steam bath units ( 3 sets) with following minimum components: 3 sets of 8 KN steam generator ( ASG-WHT-PIUVAP 5006 of ARTIZES series of Jaquar or equivalent) to be fixed on ceiling or any other suitable location as per site,IP67 rating water splash proof. Chromotherapy touch bottom display with bluetooth control music system including metal box, 8 mm thick frosted glass cubicle including all Architectural glass fixing S.S. make hardware, glass door and accessories ( for size: refer Architectural drawing) and height not less than 2.40m. Design frame for stability of Glass cubicle made of ply board covered by 6 mm thick MDF board finished with duco paint of approved colour and finish ( for size and shape refer Architectural drawing) is also included within the scope of work. All S.S.architectural glass hardware should be of ss finished from reputed make like Jaguar, Dorma or equivalent. Including necessary connecting pipelines, drain pipelines, electrical connections and finished in all respects as per instruction of Engineer- in charge. |
370 | EPBAX: Supplying ,installation, testing & commissioning of Hi-Path 1120 Digital Communication System equipped with the following: 6 P&T Ports -16 Extension PortsAuto Call Back, Built-in FAX/DIDBuilt in Voice Guided Direct inward Dialling3 party Conference In-built Caller ID100% Non- Block( SIEMENSor equivalent as approved by the Deptt.) |
371 | EPBAX:Supplying ,installation, testing & commissioning of Hi-Path 1190 Digital Communication System equipped with the following:6 P&T Ports - 30 Extension Ports(upgradeable up to 140 extensions) Auto Call Back Built-in FAX/DID 3 party Conference In-built Caller ID Supports PRI / BRBuilt in Voice Guided Direct inward Dialling 3 party Conference In-built Caller ID 100% Non- BlockSupports PRI/BR( SIEMENSor equivalent as approved by the Deptt.) |
372 | Supplying ,installation, testing & commissioning of8 port Extension Card for 1190( SIEMENSor equivalent as approved by the Deptt.) |
373 | Supplying ,installation, testing & commissioning of IPM( Integrated Protection Module , ( SIEMENSor equivalent as approved by the Deptt.) |
374 | Supplying ,installation, testing & commissioning of Digital Profiset 3030 for one Touch Button & Busy Extension Indicator for Reception & Boss, ( SIEMENSor equivalent as approved by the Deptt.) |
375 | Supplying ,installation, testing & commissioning of Open Stage 20T Digital Phone( SIEMENSor equivalent as approved by the Deptt.) |
376 | Supplying ,installation, testing & commissioning of Open Stage 40T Digital Phone( SIEMENSor equivalent as approved by the Deptt.) |
377 | Supplying ,installation, testing & commissioning of Dedicated EPABX Earthing for trouble free operation( SIEMENSor equivalent as approved by the Deptt.) |
378 | Supplying ,installation, testing & commissioning of UROSET 2005 Analog Hand set( SIEMENSor equivalent as approved by the Deptt.) |
379 | Supplying ,installation, testing & commissioning of Constant Voltage Transformer 500 VA( SIEMENSor equivalent as approved by the Deptt.) |
380 | ELECTRIFICATION WORKS:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B |
381 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C |
382 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
383 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
384 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 4 Module (125mmX75mm) |
385 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 6 Module (200mmX75mm) |
386 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm) |
387 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm) |
388 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch |
389 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet |
390 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A switch |
391 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 A socket outlet |
392 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.FOR DOOR CALL |
393 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Bell push |
394 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet |
395 | Supplying and fixing two module stepped type electronic fanregulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
396 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
397 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 1.5 Sq.mm + 1 x 1.5 Sq.mm earth wire |
398 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
399 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
400 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
401 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.: 4 x 6 Sq.mm + 2 x6 Sq.mm earth wire from VTPN DB to TPN DB forFF as required. |
402 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door |
403 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
404 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A |
405 | Supply and installation of 32A "NO"powercontactorin exixting room DB. |
406 | e) 32A ,DP Electronic switch unit with key tag Key or with keycardwith 30 sec Delay with plat 3M. |
407 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door |
408 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole |
409 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required : 32A TPN Isolator for TPN incoming |
410 | Restaurant DB: Supply, Instalation, testing and commisioning of 4 way V, TPN Double Door distribution board with MCCB incomer having fully insulated busbars and shrouded nutral bars, Earth bars, reversible door fesility, wih provision for instalation os DPX3 MCCB as incomer and SP/TPMCB as out going. (Including the supply of63A, 25KA, DPX3160 MCCB) as required for Light and sound controll system room . Make ; legrand 5077 50VTPN DB or equivalent L & T, Havells as approved. |
411 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
412 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A |
413 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
414 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
415 | Supply and Installation of 1400 sweep powerful double bearing ceiling fan. Make ; Oirent Summer breezeor equivalent Havells or Panasomic make as approved. |
416 | Supply and Installation of 1200 sweep powerful double bearing ceiling fan. Make ; Oirent Summer breezeor equivalent Havells or Panasomic make as approved. |
417 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep |
418 | Supply of 150mm high sppedexhaust fan having automatinc lovour shutter . Make ; Oirent Ventilator HSor equivalent Havells or Panasomic make as approved. |
419 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
420 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:- 1 x 12 W LED T5tube lightfitting with drive and frameMake ;SSK T5 12WSiska COB DLCor equivalent CGL/ Havells/ Suryaas approved. For study table lamp. |
421 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:- Down light2.5inch dia round shaped recess 3 watt LED,WW (3K) SMDlight fittingfor night lampMakeSiska SSK-SMD-DLS or equivalent CGL/ Havells/ Suryaas approved |
422 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:- Down light 6inch dia round surface/ recess 12 watt LED,W (6.5K)light fittingfor room lightingMake SISKA ALC 6 inch 12W or equivalent CGL/ HAVELS / SURYA as approvedfor room lighting |
423 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:- Wall light 1 x 7.5 watt A60 LED Mske Havells LHFOAKD1TZ1C060 or equivalent Siska , CGL as approved . |
424 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:- Wall light 2 x 7.5 watt A60 LED Mske Havells LHFOAKD1TZ1C060 or equivalent Siska , CGL as approved .for balcony lighting |
425 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:- Pandent light 1x7.5W LED filament lamp . Make ; Havells LHFXAFN1TN1R060 or equivalent as approved. |
426 | Supply,installation , and electrical connectin of an angle holder with 12W NW LED BULB for toilet, dressing room, back office andPantryas directed |
427 | Supply of 6 / 7W LED WW (3000K) recess COB down lightlamp set . Make ; Syska, SSK-LNTH-201F1-PA-7W |
428 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:-: 1 x 3 W LED, 3000K,WWspotlightfitting with drive and frameMake ;SISKA - SSK MR 163Wor equivalent CGL/ Havells/ Suryaas approved. For GFfalse ceiling light as directed. |
429 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:-: 1 x 2 W LED, 3000K,WW cabinatespotlightfitting with drive and frameMakeSISKA - ;SSK CL2Wor equivalent CGL/ Havells/ Suryaas approved. ForFF false ceiling light as directed. |
430 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:-: Down light 6inch dia square surface 12 watt LED,W (6.5K)light fittingfor kitchen, pentry , toilet and varandalightingMake SISKA=SSK SDS 12W N or equivalent CGL/ HAVELS / SURYA as approvedfor room lighting (7 lights in each room ) |
431 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:-:KELIC Pandent ropelightfor ceiing hanging light with 40W E27 Havells makeround filament lamp or equivalent as approved by CA. |
432 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:-: Cardio Light with E27 40Watt WWwith Havells make filamentlampforHanging Ceiling lightmade out of rope netting , elegant, vintage touch suitable for resturent etc. with 2 mtr. Flexible rope and wire with bulb |
433 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:-: Brightyt Bamboo Hanging Pendant light made out of natural bamboo & rope - Black & Yellow coloured with E26/E27 40W WWFilament Havells make Screw type bulb or equivalent as approved. |
434 | Supply of Pandent light Make ; HavellsLHF XAGNT1TN1fO6Owith 4 W WW E27LEDFilament lamp or equivalent as approved. |
435 | RGB Strip lightwith suitable drivefor installation in outer periferry of screen and in false ceiling as directed . Make SISKA - SSK-ST-5530- RGB-OP-EX-Dor equivalent CGL, Havells , Philips as approved. |
436 | Supply of IP 65, 10W LED CDL 3Kbollardinverted prism type made up of extruded aluminium with PC defuser Make ; Libra ( Ref. Cat. No. LBLSN 10 CDL)of CGL or equivalent Havells, Surya, Philips, Siskaas approved. |
437 | Supply and installation of 8 / 9 W 3K spike gardenlight in die cast aluminium housing with high quality toughened glass diffuser. Make SSK ;3771DZof Siskaor equivalent CGL, Surya , Havells as approved. |
438 | Supply and installation of 12W WW 3K LED surface mounted bush lightingin die cast aluminium housing with high quality toughened glass diffuser. Make SSK ;3005of Siskaor equivalent CGL, Surya , Havells as approved. |
439 | Supply and installation of 1.5TRDual Inverter type 5 star Air conditioner with necessary piping etc., Stabilizer free, HD filteras required incomplete. . Make ; Dikin , LG, Blue Star. |
440 | Supply and installation of modular32A AC starter switch on exixting 2modulebox. |
441 | Supply, installaton andtesting & commissioning of 2TR 5 star Dual Inverter type split Air Conditionerwith all necessary assessosaries to complete as required. Make ; LG / Dikin / Blue star. |
442 | Supply and installation of 15 Lts Geyserwith necessary piping etc. as required to complete the job. Make : CGL Solarium Cube or equivalent Smith /Jaquare. |
443 | Supplying of300 mm sweep high speedExhaust fans suitable for 230 Volt, 50 Hz, Single phase, A.C. supply and complete with all standard accessories required. Havells Ventil Air - Dx or similar of approved make.For Kitchen & Dining hall |
444 | Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmouredcable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEIOr equivalent as approved 4 Core, 16 sq.mm. XLPEARMOURED Aluminium Cable. |
445 | Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmouredcable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEIOr equivalent as approved: 4 Core, 35 sq.mm. XLPEARMOURED Aluminium Cable. |
446 | Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmouredcable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEIOr equivalent as approved 3 Core,6 sq.mm. XLPE armouredAluminium Cable forJuhal and kitchen power supply |
447 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Up to35 sq. mm |
448 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle) |
449 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35sq. Mm |
450 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm (28mm) |
451 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 6 sq. mm (19mm) |
452 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3 X 4 sq. mm (19mm) |
453 | Supply and making cable end termination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required.:4CX 25 sq. mm (45mm) |
454 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
455 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
456 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
457 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
458 | Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) |
459 | Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) |
460 | Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. |
461 | Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required. |
462 | Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. |
463 | Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required. |
464 | Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. |
465 | Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. |
466 | Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 zone |
467 | Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. TwoLoop Panel. |
468 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2x1.5 sqmm |
469 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm |
470 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm |
471 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm |
472 | Supply andistallation of 4.5 Kg, Mild steel ABC, A class powder/ CO2 type fire extenguisher |
473 | Supplying and fixing of light class G.I. pipe of 50 mm dia.(nominal) 3 metres length along the pole for protection of under ground cable as required. |
474 | Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required. 40 mm dia |
475 | Construction of 400mm x 400mm x 400mm masonry manhole with air tight C.I. Cover requiresfor earthingpoint tocover. |
476 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair |
477 | Supply and installation of KRONE connector type main telephone tag block of following sizes in sheet metal enclosure of suitable dimensions fabricated out of 16 SWG sheet steel with castle key lock, hinged type cover including termination of telephone cables, making connections, painting of box etc. complete as required 10 Pairs |
478 | Supply and installation of KRONE connector type main telephone tag block of following sizes in sheet metal enclosure of suitable dimensions fabricated out of 16 SWG sheet steel with castle key lock, hinged type cover including termination of telephone cables, making connections, painting of box etc. complete as required 50 pair |
479 | Supply of followingpoly ethyline insulated armoured jelly filled telephone cables as per DOT specification 20 pair 0.5mm dia armoured copper telephone cable |
480 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
481 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet |
482 | Supplying and fixing of Splitter box in suitable size of G.I. Enclousure with cover plate including connections and making good the damage etc. as required. 2 way |
483 | Supplying and fixing of Splitter box in suitable size of G.I. Enclousure with cover plate including connections and making good the damage etc. as required. 3 way |
484 | Supply, installaton andtesting & commissioning of 1.5TR 5 star Dual Inverter type split Air Conditioner including 4KVAAutomatic voltage stabilizer havingnormal / out cut /on delay indication andStarter of requiredcapacity with all necessary assessosaries to complete as required. Make ; LG / Dikin / Blue star. |
485 | Corded telephone hand set Make ; Panasonic black or equivalent |
486 | Telephone intercom system 4 main / trunk/fct device line and 24 Land line phone subscriber connection pabx PBX 424 |
487 | Supply and installation of 32 inch HD LED TV . Make ; Sony, LG and Samsung as approved. |
488 | Supply and installation of 55 inch HD LED TV . Make ; Sony, LG and Samsung as approved. |
489 | Supply, installation, testing and commissioning of followingExternal LT powerdistributionPanel Boards of 2 mm thick CRCA MSsheet steel cubical design for indoor WALLmounting factory fabricated suitable for operation on 440 V, 3 phase, 50 Hz, A.C. supply with24 Hrs. time switch/ MCBs/ contactors,and other accessories, all in compartmentalised, cubical construction complete in all respects as per approved drawing and design including internal wiring, inclusive oftinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs for out gogoing , cable termination gland plates,painting etc. conforming to specifications as required.The panel shall have porvision of cable entry and out goingat the bottom. The busbar shall be sized with current density of Amperage 1A/sq.mm and MCB shall be connected using FR cables of proper rating. 24 Hours time switch 1 no. 63A TP, 36KA,MCB for incoming feeder1 no 63 A NOTP Contactor 1 no. 200 A AluminiumBus bars with heat shrinkable color coded PVC sleeves shall be of E91E grade. Neutrar bar Earth bar 40A TP, 25KA MCB forout gogoint 2 no. 25 A SP , 16KA, MCB forout gogoint 4 no |
490 | Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmouredcable conforming to IS 1554 (Part-I) 1988. 3 Core,4 sq.mm. XLPE armouredAluminium Cable forJuhal and kitchen power supply |
491 | Supply of IP 65, 10W LED CDL 3Kbollardinverted prism type made up of extruded aluminium with PC defuser Make ; Libra ( Ref. Cat. No. LBLSN 10 CDL)of CGL or equivalent Havells, Surya, Philips, Siskaas approved. |
492 | Supply of IP65, 60W LED CDLdecorative street light for beautification application. Make ; Empire( Ref. Cat.No. LPTC 40 CDL)of CGL /Vega of Surya or equivalent Siska, Havells, Philipsas approved. |
493 | Supply of 9W IP65LED 6KGARDENlight in die cast aluminium housing with high qualify toughened glass diffuser for illumination of bush, garden etc.Ref. Cat No. SSK3005 12W 3K ofSiska or equivalent Surya, CGL, Havels as approved. |
494 | Supply and installation of 9W 3K bush light in die cast aluminium housing with high quality toughened glass diffuser. Make ;Mallow of Surya or equivalent CGL, Siska , Havells as approved. |
495 | Supply and installation of 8 / 9 W 3K spike gardenlight in die cast aluminium housing with high quality toughened glass diffuser. Make SSK ;3771DZof Siskaor equivalent CGL, Surya , Havells as approved. |
496 | Supply of 70 W LED W IP66aerodynamically design made out of die cast Aluminium housing and head frame, powder coated in approved color including driver andaccessories as required. . forB - block road sidearea Make; CGL make Ref.Cat No. Hawk Neo LSTN170 CDL AMor equivalent Siska , Panasonic, Surya, Havells as approved. |
497 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 1.5 sq. mm |
498 | Supply and installation of IP55 Poly carbonate SMC box size 230mmx170mmx105mm door fixed hinged (make - syntex) with 6A DPMCBalong with earth barandnecessary two nos. ofclampsrequired to fit the box on the pole at required position or as directed . |
499 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
500 | Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 4.5 metre and upto 6.5 metre |
501 | Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 6.5 metre and upto 8.0 metre |
502 | Supply of 8 mtr long galvanised octagonal pole with inbuilt JBarrangement HAVING DIN bar and Earth link bar(Top 70mm, Bottom 155mm, Thickness 3mm, Base plate 220x220x12 mm , 220 mm PCB. With single armMake Crompton, Jindal, Niozon as approved. |
503 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole |
504 | Supply of 6 mtrs heightdecorative polewith inbuilddecorativearmmatching with the lamps set as described under sl. No. 2 c .Please refer CGL decorative pole cataloguefor CGL set or for Surya makeset please refer corwndecorative pole oras approved for other company make decorative set. |
505 | IP IR DomeCamera6MP DS-2CD2163G0-IU 1/2.9" Progressive Scan CMOS ? 3072 × 2048@20fps ? H.265, H.265+, H.264, H.264+ ? Three streams ? 120dB WDR IR range: Up to 30 m ? IP66, IK10 ? Built-in micro SD/SDHC/SDXC card slot, up to 128 GB ? 3-Axis adjustment ? Built-in microphone 6 MP IR Fixed Dome Network Camera. MODEL CODE ; DS-2CD2163G0-IU or equivalent as approved. |
506 | DS-2CD2063G0-I1/2.9" Progressive Scan CMOS BLC/3D DNR/ROI/HLC IP67 CAMERA Built-in micro SD/SDHC/SDXC card slot, up to 128 GB 3072 × 2048@20 fps 2.8/4/6/8 mm fixed lens Color: 0.01 lux @(F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR H.265+, H.265, H.264+, H.264 2 Behavior analyses 120dB WDR 6 MP IR Fixed Bullet Network Camera. MODEL CODE ; DS-2CD2063G0-I or equivalent as approved . |
507 | DS-2CD6362F-I(V)(S) 6MP Fisheye Network Camera 1/1.8” Progressive Scan CMOS ? 6 megapixel image sensor ? Up to 3072 × 2408 resolution, real-time streaming ? Multiple viewing modes ? Line crossing and intrusion detection ? Ceiling, wall or table mount modes ? Up to 15m IR range ? 360° view angle ? Built-in microphone & speaker ? Audio/Alarm IO/ RS485(-S model) ? IP66(-V model) ? IK10 vandal proof(-V model) MODEL CODE :DS-2CD6362F-IS or equivalent as approved. |
508 | NVR 64 CHANNEL Professional and Reliable ? New logical and visualized GUI design ? Dual-OS design to ensure high reliability of system running ? ANR technology to enhance the storage reliability when the network is disconnected ? HDD hot swap with RAID0, RAID1, RAID5, RAID6 and RAID10 storage scheme configurable ? Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission ? Up to 64-ch 12 MP IP cameras can be connected ? Connectable to the third-party network cameras Compression and Recording ? H.265+ compression effectively reduces the storage space by up to 75% ? Full channel recording at up to 12MP resolution HD Video Output ? HDMI1/VGA1 and HDMI2/VGA2 outputs provided ? HDMI1 Video output at up to 4K (3840 × 2160) resolution Storage and Playback ? Up to 8 SATA interfaces and 1 eSATA interface for HDD connection ? 10TB capacity for each HDD ? Smart search for efficient playback ? 16-ch synchronous playback at up to 1080p resolution ? Normal/Important/Custom video playback ? Important files management ? HDD health monitoring Smart &POS Function ? Supports multiple VCA (Video Content Analytics) events ? Smart search for the selected area in the video; and smart playback to improve the playback efficiency ? Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files ? POS information overlay on live view and playback ? POS triggered recording and alarm MODEL CODE ; DS-8664NI-I8orequivalent as approved |
509 | CAMERA INSTALLATION CHARGE |
510 | 50 Inch LED FULL HD display 127 CM DIAGONALMODEL CODE ; LH50AN3ND or equivalent.as approved. |
511 | 6TB SATA HDD MODEL CODE ; ST6000VX001 or equivalent as approved |
512 | 16 Port PoE Switch : MODEL CODE : DE3E0518P-E or equivalent as approved. |
513 | 6U Wall mount rack with all accessories. MODEL CODE : NWR-6U-5045-GR |
514 | CAT6 out door networking UTPCable.MAKE CODE ;NCB-C6UGRYR-305 |
515 | Supply of octagonal 6 mtr heightGI pole base dia 130 mm and 70mm top diawith base plate andnuts and bolts etc. as required. |
516 | Installation of all items including errection of poles with PCC foundations, Laying of CCTV cable on OH or under ground by using HDP pipe etc. as required . This also include intallation of cameras and other ancillary works with necessary clamps as required as per standard procedureand asdirected- a lot |
517 | NVR RACK AND OTHER ACCESSORIES a lot ofwork |
518 | FEEDER PILLAR:Supplying and fixing in PCC foundation of followingOUT DOORIP65- rain and dust prooffeeder pillarfor street light LT power distribution board ,for operatin in230V,, made of 2mm CRCA MSsheet steel,dust & rainprotected, duly powder painted, inclusive oftinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs for out gogoingconforming to specificationsetc as required.The panel shall have porvision of cable entry andout going at the bottom. The busbar shall be sized with current density of Amperage 1A/sq.mm and MCB shall be connected using FR cables of proper rating. 40A DP Isolatorfor incoming feeder1 no :36 A Bus bars : Neutrar bar:Earth bar :25 A, SP, 16KA MCBout gogoint 4 no |
519 | FOR 11KV OH LINE : SP 56 Length of pole = 11.00 metreslength, coated with black bituminous paint (internally & externally) up to the earth level , with 14 mm. diameter through hole for earth connection, including grouting with concrete (1:2:4) on steel base plate.( Length of sections of poles are Bottom = 5.20 M, Middle =3.40 M, Top = 2.40 M, Out side dia. & Thickness Bottom = 165.10 x 4.50 mm, Middle =138.70 x 4.50 mm, Top =114.3 x 3.65 mm |
520 | G.I. channel cross arm 100 x 50 x 6 x2200mm |
521 | G.I. angle 50 x 50 x 6 mm. for guard bracket |
522 | GI 11KV Cross Arm with angle size 50x50x6 mm |
523 | I.Hook - GI |
524 | 11KV Disc Insulator ( Polimer ) 72 KN ( B&C Type ) |
525 | 11KV PIN insulator (Polimer ) 5KN (FRP 24mm ) |
526 | ACSR "Racoon" conductor |
527 | Tension clamp for ACSR "Racoon" conductor |
528 | Ploe Clamp ofGI Flat 50x6 mm |
529 | G. I. wire 8 swg. for guarding |
530 | Hot Dip G. I. wire 6 swg. for earthing (every pole to be earthed) |
531 | HT Stay Set |
532 | Hot Dip GI Wire Stay Wire 7/10SWG ( for HT) |
533 | 11KV Guy Insulator (Porcelain ) |
534 | G.I Earthing pipe50mm dia , 3m length, 3.15mm thickness with perforated holesofdia 15mm dia at 30cm length along length ofthe epipe Earthing as per latest amendments of Indian Electricity Rules 2003 |
535 | GI Strip 25x3 mm for DTR Earthing |
536 | PG clamp, for ACSR "Racoon" conductor |
537 | PG clamp, for ACSR "Racoon" conductorDanger plate "11000 volts" |
538 | Bimatalic Lug 300 sq mm |
539 | Bimatalic Lug 185 sq mm (for neutral ) |
540 | 11KV GOAB Switch 400 Amp |
541 | 11KV DO Fuse Set 150A Assembly |
542 | 11KV, 5KA Linghtning Arrestor line type |
543 | 3P4W ICS DLMS compliant HT Trivector energy meter |
544 | 3 Ph 4W Combined CT/PT Accuracy Class : 0.5,25/5A |
545 | Control Cable1 Core X 2.5 sq. mm |
546 | Metering Cabinate |
547 | 11KV Danger plate |
548 | AMR Modem |
549 | Sundries L/S |
550 | Transporatation & storage on materials, labour charges, contingency and supervision charges. |
551 | Load security to be deposited to APGCLfor 425kW Commercial Load = |
552 | FEEDER PILLAR 1 ( TO BE INSTALLED IN NEAR TRANSFORMER )::Design, manufacture, supply, installation, testing and commissioning of cubicle type panel fabricated out of 14 SWG CRCA sheet steelsheet steel, IP65, rain, ,dust protected, ,OUT DOOR , floor mounted totally enclosed switch baord suitable for use of 415 volts , 3 phase, 50HZ complete with aluminium bus-bar and all accessories including supply and fixing of following incoming and outgoing switchgears. The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness Incomer:Two nos. 3.5Core 300 sq. mm U/G Aluminium Cablefeeders from 500KVA Transformer .Accordingly arrangement of bus bar connection has to be provided to connecttwo nos. incoming feeders to the incoming MCCB. Incomer = FP 600 A 50 KA Ics= 100% Icu MCCB withspreader terminal - 1 Nos. Digital Ammeter0-800A, 3 Phase 4 WireAccuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96mm:1 No. Digital Voltmeter - 0-500V 3 Phase 4 WireAccuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96mm :1 Nos. CT 800/5 240V 3 Phase 4 wire Freq 50Hz+/- 5% Accuracy Class 0.5S : 1 Set SP MCB with 10KA breaking capacity of rating 6 Amp :03 Nos RYB Indicating Lamps : 1 set 1000 A TPN AL. bus bar with coloured heat shrinkable PVC sleeve-1 Set Outgoings:200A,3P,MCCB,25KAMRP- 3 Nos. 63A,3P,MCCB,25KAMRP- 2 Nos. forBanani and 1 for Spare.LED indication lamp(R Y B ) with MCB pretection as necessary.Earthing Bus |
553 | FEEDER PILLAR -2 ( TO BE INSTALLED IN BANASHREE ) :Design, manufacture, supply, installation, testing and commissioning of cubicle type panel fabricated out of 14 SWG CRCA sheet steel sheet steel, IP65, rain, ,dust protected,, OUT DOOR , floor mounted totally enclosed switch baord suitable for use of 415 volts , 3 phase, 50HZ complete with aluminium bus-bar and all accessories including supply and fixing of following incoming and outgoing switchgears. The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness Incomer:FP 200 A 50 KA Ics= 100% Icu MCCB withspreader terminal - 1 Nos. Digital Ammeter0-250A, 3 Phase 4 WireAccuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96mm:1 No. Digital Voltmeter - 0-500V 3 Phase 4 WireAccuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96mm :1 Nos. CT 250/5 240V 3 Phase 4 wire Freq 50Hz+/- 5% Accuracy Class 0.5S : 1 Set SP MCB with 10KA breaking capacity of rating 6 Amp :03 Nos RYB Indicating Lamps : 1 set 800 A TPN AL. bus bar with coloured heat shrinkable PVC sleeve-1 Set Outgoings: 100A,3P,MCCB,25KAMRP- 2 Nos.FOR PRASANTI( future ) and 1 spare63A,3P,MCCB,25KAMRP- 3 Nos.- FOR Banashree,Kunjaban,and 1Spare 40A,3P,MCCB,25KAMRP- 3 Nos.- For SPA, SparePalican Bar, and 2 spare LED indication lamp(R Y B ) with MCB pretection as necessary. |
554 | TRANSFORMER : Supplying, installation testing and commissioning of the following rating copper woundout door type transformer. Transformer should be as per CEA / BIS guidelines as ammended up to datefor losses along with LV enclosure.: 500 KVA, 50Hz. 11/0.433 KV. Oil filledLEVEL 2, 4 STAR ,COPPER WINDING transformer . |
555 | TRANSFORMER FOUNDATION: Providing andlayinginpositioncementconcrete1:3:6(1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) for feeder pillarsfoundation /transformer pad of above transformeretc including frame works etc as directed. |
556 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.for transformer neutral grounding. |
557 | Supplying and layingdoublerun 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection terminating with nut,bolt, spring, washer etc. asrequired. |
558 | CABLE WORKS FOR POWER SUPPLY : Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmouredcable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEIOr equivalent as approved:3.5 Core, 300 sq.mm. XLPEARMOURED Aluminium Cable. From Transformer to Feeder Pillar 1 ( two run ) and from Feeder Pillar 1to Banashree feeder pillar - incoming feeder) |
559 | CABLE WORKS FOR POWER SUPPLY :Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmouredcable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEIOr equivalent as approved: 4 Core, 50 sq.mm. XLPEARMOURED Aluminium Cable. FromFeeder Pillar 1 to Banani and from Feeder pillar 2 to Banashree and Kunjaban |
560 | CABLE WORKS FOR POWER SUPPLY :Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmouredcable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEIOr equivalent as approved: 4 Core, 35 sq.mm. XLPEARMOURED Aluminium Cable. FromFeeder Pillar 2 to Palican bar and SPA |
561 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required:Above 35 sqmm andUp to95 sq. mm |
562 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required.: Above 185 sqmm andUp to400 sq. mm |
563 | Laying ofonenumberadditionalPVCinsulatedandPVC sheathed / XLPE power cable of 1.1 KV grade of following sizedirect in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.:Above 35 sq. mm and upto 95 sq. mm ( from feeder pillar 1 to Banani ) |
564 | Laying ofonenumberadditionalPVCinsulatedandPVC sheathed / XLPE power cable of 1.1 KV grade of following sizedirect in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.:Above 185 sqmm andUp to400 sq. mm ( from Transformer to Feeder pillar 1 ) |
565 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.: Above 35sq. Mm and up to 95 sq. mm |
566 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.:Above 185 sqmm andUp to400 sq. mm |
567 | Supply and making cable end termination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required.:3½ X 300 sq. mm (82mm) |
568 | Supply and making cable end termination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required.: 4C X 50 sq. mm (19mm) |
569 | Supply and making cable end termination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required.:4C X 35 sq. mm (19mm) |
570 | GI PIPES : Supplying and embedding following G.I pipe of medium class for cable entry / road crossing of cable etc. including bending the pipe as required shape as required.b) 40 mm dia |
571 | Supply and installation of4.5KgMild steel ABC type CO2 type fire extenguisher |
572 | DISEL GENERATOR ( DG ):Supplying including installation, testing and commissioning ofAir/Water Cooled Diesel Generator set coupled to suitable alternator of 240 V, AC, 1/3-Phase 0.8 p.f.(la mounted on a1)M.S. Fabricated base frame.,2)M.S. fuel tank of required capacity.,3)Residual Silencer.,4) Standard Control Panel.5)Suitable batteries with lead.,5) First fill of lubeoil.,6)Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer. Kirloskar green/bliss, Leyland, Mahindra, Greaves, Escort engine and Jackson, as approved with auto start and auto changeover facilities.:10 KVA DG |
573 | DISEL GENERATOR ( DG ): Supplying including installation, testing and commissioning ofAir/Water Cooled Diesel Generator set coupled to suitable alternator of 415 V, AC, 1/3-Phase 0.8 p.f.(la mounted on a1)M.S. Fabricated base frame.,2)M.S. fuel tank of required capacity.,3)Residual Silencer.,4) Standard Control Panel.5)Suitable batteries with lead.,5) First fill of lubeoil.,6)Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer. Kirloskar green/bliss, Leyland, Mahindra, Greaves, Escort engine and Jackson, as approved with auto start and auto changeover facilities. 35 KVA- DG |
574 | DISEL GENERATOR ( DG ): Supplying including installation, testing and commissioning ofAir/Water Cooled Diesel Generator set coupled to suitable alternator of 415 V, AC, 1/3-Phase 0.8 p.f.(la mounted on a1)M.S. Fabricated base frame.,2)M.S. fuel tank of required capacity.,3)Residual Silencer.,4) Standard Control Panel.5)Suitable batteries with lead.,5) First fill of lubeoil.,6)Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer. Kirloskar green/bliss, Leyland, Mahindra, Greaves, Escort engine and Jackson, as approved with auto start and auto changeover facilities. 50 KVA- DG |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail