Military Engineer Services-MES has published Repair / Maint Submersible Pumping Sets, Lt Panels, Water Level Indicators, Dosing Equipment And Certain Misc Work At Fatehgarh Cantt Under Age ( I ) Fatehgarh Repair / Maint Submersible Pumping Sets, Lt Panels, Water Level Indicators, Dosing E. Submission Date for this Tender is 08-11-2021. Electrical Panel Tenders in AGE (I) Fatehgarh Uttar Pradesh. Bidders can get complete Tender details and download the document.
Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
1 | 23-Oct-2021 | Amendment to estimated cost | Other | 01-11-2021 |
2 | 01-Nov-2021 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 08-11-2021 |
Sl. No. | Item Description |
1 | Supply & fix in replacement of DOL Starter 415 Volt suitable for 5 HP motor complete all as specified and directed. |
2 | Supply & fix in replacement of ContactorML-3 rangge 50-70 Amp suitable to operate 40-45 HP submersible pumping set complete all as specified and directed. |
3 | Supply & fix in replacement of ContactorML-2 rangge 35-60 Amp suitable to operate 20-40 HP submersible pumping set complete all as specified and directed. |
4 | M&L for cleaning of RCC Over Head Tanks capacity 1 lakh gallon removing and taking out sand, sludge and mud etc including dispossed of the same at a distance not exceeding 100 mtrs from the tank,including two coats of whitewash on whole internal walls of OH Tank complete all as specified and directed . (NOTE:-All the safety equipments for workers working on OHT and U/G Sumps will be provided by the contactor) |
5 | …..ditto as above but for capacity 50000 gallon complete all as specified and directed. |
6 | …..ditto as above but for capacity 40000 gallon complete all as specified and directed. |
7 | …..ditto as above but for capacity 30000 gallon complete all as specified and directed. |
8 | …..ditto as above but for Under Ground Sump capacity 10000 gallon complete all as specified and directed. |
9 | M&L for taking out unserviceable submersible pumping set complete with column pipe any capacity and any type from existingbore well carefully without damaging the p/set including connecting parts and lowering the same after repair including provision of suitable size of nut & bolts with washer and suitable packing for column pipes and connection of submersible cable complete all as directed. NOTE: (1) Chain pully block and clamps etc shall be provided by the department. (2) Necessary safety pracaution will be responsibility of the contractor. (3) Parts replaced of submersible pump set shall be measured and paid seperately under relevant item here in after under as supply only. (4) No extra payment will be made to the contractor for note (1) and (2) above |
10 | Dismantling of submersible motor of 40 to 41 HP motor and taking out unserviceable spares and burnt copper binding wire complete. M&L for rewinding of submersible motor withinsulated copper winding wire including sleeves as per original company and replacement of worn out parts,including grinding & polishing of rotor sleeves and refixing, testing& transport charges completeall as specified & directed. Note:(Partsfor followingitems shall be paid under relevent item here-in-after under as supply). |
11 | …ditto as above but for 30 HP 35 HP motor ….ditto… |
12 | …ditto as above but for 25 HP motor….ditto… |
13 | …ditto as above but for15 HP motor….ditto… |
14 | Supply only Neck ring of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
15 | Supply only Shaft sleeve of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
16 | Supply only Pump shaft of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
17 | Supply only Coupling of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
18 | Supply only Coupling key of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
19 | Supply only Impeller key of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
20 | Supply only Stud with nuts of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
21 | Supply only Thrust bearing of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
22 | Supply onlyLower housing bush of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
23 | Supply only Upper housing bush of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
24 | Supply only Rotor shaft sleave of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
25 | Supply only Drain plug of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
26 | Supply only Water seal of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
27 | Supply only CI Bowl of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
28 | Supply only Rotor Shaft of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
29 | Supply onlyball bush of the submersible pump and motor for capacity upto 15 HP of existing make/company completeall as specified & directed. |
30 | Supply only Impeller of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
31 | Supply only Neck ring of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
32 | Supply only Shaft sleeve of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
33 | Supply only Pump shaft of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
34 | Supply only Coupling of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
35 | Supply only Coupling key of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
36 | Supply only Impeller key of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
37 | Supply only Stud with nuts of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
38 | Supply only Thrust bearing of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
39 | Supply onlyLower housing bush of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
40 | Supply only Upper housing bush of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
41 | Supply only Rotor shaft sleave of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
42 | Supply only Drain plug of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
43 | Supply only Water seal of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
44 | Supply only CI Bowl of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
45 | Supply only Rotor Shaft of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
46 | Supply onlyball bush of the submersible pump and motor for capacity upto 25 HP of existing make/company completeall as specified & directed. |
47 | Supply only Impeller of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
48 | Supply only Neck ring of the submersible pump and motor for capacity30 to 35 HPof existing make/company completeall as specified & directed. |
49 | Supply only Shaft sleeve of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
50 | Supply only Pump shaft of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
51 | Supply only Coupling of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
52 | Supply only Coupling key of the submersible pump and motor for capacity30 to 35 HPof existing make/company completeall as specified & directed. |
53 | Supply only Impeller key of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
54 | Supply only Stud with nuts of the submersible pump and motor for capacity 30 to 35 HP of existing make/company completeall as specified & directed. |
55 | Supply only Thrust bearing of the submersible pump and motor for capacity 30 to 35 HP of existing make/company completeall as specified & directed. |
56 | Supply onlyLower housing bush of the submersible pump and motor for capacity 30 to 35 HP of existing make/company completeall as specified & directed. |
57 | Supply only Upper housing bush of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
58 | Supply only Rotor shaft sleave of the submersible pump and motor for capacity 30 to 35 HP of existing make/company completeall as specified & directed. |
59 | Supply only Drain plug of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
60 | Supply only Water seal of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
61 | Supply only CI Bowl of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
62 | Supply only Rotor Shaft of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
63 | Supply onlyball bush of the submersible pump and motor for capacity30 to 35 HP of existing make/company completeall as specified & directed. |
64 | Supply only Impeller of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
65 | Supply only Neck ring of the submersible pump and motor for capacity40 to 41 HPof existing make/company completeall as specified & directed. |
66 | Supply only Shaft sleeve of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
67 | Supply only Pump shaft of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
68 | Supply only Coupling of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
69 | Supply only Coupling key of the submersible pump and motor for capacity40 to 41 HPof existing make/company completeall as specified & directed. |
70 | Supply only Impeller key of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
71 | Supply only Stud with nuts of the submersible pump and motor for capacity 40 to 41 HP of existing make/company completeall as specified & directed. |
72 | Supply only Thrust bearing of the submersible pump and motor for capacity 40 to 41 HP of existing make/company completeall as specified & directed. |
73 | Supply onlyLower housing bush of the submersible pump and motor for capacity 40 to 41 HP of existing make/company completeall as specified & directed. |
74 | Supply only Upper housing bush of the submersible pump and motor for capacity 40 to 41 HP of existing make/company completeall as specified & directed. |
75 | Supply only Rotor shaft sleave of the submersible pump and motor for capacity 40 to 41 HP of existing make/company completeall as specified & directed. |
76 | Supply only Drain plug of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
77 | Supply only Water seal of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
78 | Supply only CI Bowl of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
79 | Supply only Rotor Shaft of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
80 | Supply onlyball bush of the submersible pump and motor for capacity40 to 41 HP of existing make/company completeall as specified & directed. |
81 | Supply & fix in replacement of Water pressure guage 100 mm dia in size ranging 0 to 25 kg/ sq cm calibrationcomplete with size 3/8"X1/2" and brass cock 1/2" dia complete all as directed. |
82 | Supply & fix in replacement ofelectronic Timer for Star Delta Starter type ETSD2 Cat No TESD 2 timing range 3-30 sec complete all as specified and directed. |
83 | Supply & fix in replacement of Single Phase Preventor for 15/25/35/41 HP submersible pumping set motor complete all as specified and directed. |
84 | Supply & fix in replacement of overload protection relay for FASD starter ranging 28-42/30-35 Amp complete all as specified and directed. |
85 | S&F in replacement of Digital type ampere meter of size 96x96mm with CT 100/5 Amp,AC,3 phase,415 volts complete all as specified & directed. |
86 | S&F in replacement of Digital type voltmeter of size 96x96mm AC, 3P, 415 volts complete all as specified and directed. |
87 | Supply,fixing ,testing and commissioningsubmersible cable ,flat, 16 sqmm,3 core,PVC insulated and PVC sheathed with multi stranded, copper conductor,1100 Volts grade ,fixed to submersible motor column pipe,using suitable size of clamps made out of stainless steel flat of size 20 x2mm with steel nuts ,bolts & washer for every column pipe of 3 m length complete all as specified and directed. |
88 | Supply,fixing ,testing and commissioningsubmersible cable ,flat, 10 sqmm,3 core,PVC insulated and PVC sheathed with multi stranded, copper conductor,1100 Volts grade ,fixed to submersible motor column pipe,using suitable size of clamps made out of stainless steel flat of size 20 x2mm with steel nuts ,bolts & washer for every column pipe of 3 m length complete all as specified and directed. |
89 | M&L in replacement of star delta starter without sheet metal enclosure fixed in existing panel for FASD starterwith relay ranging 45 to 70 Amps, suitable for submersible pumping 3 Phase,415 Volts,50 Hz including single phase preventor complete all as specified and directed. |
90 | M&L in replacement of star delta starter without sheet metal enclosure fixed in existing panel for FASD starterwith relay ranging 30 to 50 Amps, suitable for submersible pumping 3 Phase,415 Volts,50 Hz including single phase preventor complete all as specified and directed. |
91 | S&F in replacementMCCB , 4 pole, 415 Volt, fixed type 315 amp with breaking capacity 35 kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed. (Make: C&S/L&T/Havells.) |
92 | S&F MCCB , 4 pole, 415 Volt, adjustable type 250 Ampwith breaking capacity 36kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed.(Make: C&S/L&T/Havells) |
93 | S&F in replacement MCCB , 3 pole, 415 Volt, fixed type 200 amp with breaking capacity 36 kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed. |
94 | S&F in replacement MCCB , 3 pole, 415 Volt, fixed type 100 amp with breaking capacity 16 kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed. |
95 | S & F in replacement synthetic rubber insulated mats 2 mm thick for voltage upto 3.3 kV for electrical purpose as per IS 15652 of 2006 (superseding IS 5424) suitable for electrical shock safety of size 2 m x 1 m |
96 | M & L for painting of rising , delivery , overflow and washout pipes of following capacity OH tank of various Diameter and height with Blue, green, red and yellow colours respectively with syntheic enamel paint two coats including marking with arrows ( directions of flow ) and writing date of cleaning with white synthetic enamel paint over black ( syntjetic enamel paint ) background of size (300mm x 300mm) all as specified and directed by Engneer in Charge. |
97 | Testing of Raw and treated water of capacity 50 KLD STP for the following parametersBOD,COD, Focal Coliform (FC) testing will be carried out from Govt authorised agencies/Lab , the sample of Raw and treated water obtain from STP in sealed plastic containers Note: .Transportation charges of water samples for testing shall be borne by the contactor |
98 | Material & labour for water sample colletcted from all pump houses of the station for testingfrom HBTI Kanpur/Jal Nigam board, Kanpur or authorised agencies for testing of water for chemical and bacteria logical tests as per IS:10500. Sample of water obtained from pump houses in sealed plastic containesr of 5 ltrs capacity.Transportation charge of water samples for testing shall be borne by the contractor.The following tests are required at each pump houses. (i)pH test(ii)Total Dissolved Solids (TDS) test (iii) Coliform test (Microbiological test)(iv)Total hardness test(v)Calcium hardness test (vi) Fluoride test and (vii) Iron test |
99 | Supply ,installation, testing and commissioning in replacement of electrical cubical controlpanel box indoor type3 phase 4 wire ,415 volts ,50 Hz , pedestal type indoor LTPanel factory made with front and rear opening doors, weather and vermin proof IP-42 to IP-55 protection categoryfabricated with 2.00 mm thick CRCA steel sheet , duly paintingwith anti corrosive coating and finally polyester powder coating in RAL 7035 , Jay whiteshed complete with suitable padlocking arrangement,earthing terminals with suitable rating aluminiumstrips such as Volt meter ,Ammeter, Selector switches,CTs ,phase indicator lamps with holder,etc including incoming and outgoing cable connections withbrass cableglands and end termination including grouting of Feeder pillar box 60 cm above the ground level by providing 90 cm long angle iron ofsize 50x50mmx6mm welded on all four corner embedded in PCC platform casted in1:2:4 type B-1 ,30 cm high from GLetc complete incl and providingall as specified below and directed . (a) MCCB315 Amps, 4 pole, 50 KA -01(Incoming) (b)MCCB 125 Amp, 4 Pole, 415V,35 KA -03 Nos (Outgoing) (c) Star delta starter suitable for 40 HP pump motor, 415 Volt, 50 (d) Single phase preventor for 415 AC supply-01 Nos (e) Digital panel mounted Amp 500 Amp Volts 96x96 mm square type complete with selector switch with suitable size of CTs -01 set (f) Digital panel mounted voltmeter 0-500 Volts 96x96 mm square type complete with 3 phase selector switch with suitable sizepf CTs -01 Set (g) RYB indicating lamps LED type -01 set (h) Metering Eqpt and connections etc. (i) Feeder Pillar Box Complete with all accessories incl fabrication completeand Layout sketch of the Panel board shall submitted by the contractor for the approval of GE before placing the order. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail