Public Works Department-PWD has published Repair / Renovation Of Executive Engineer Pwd ( Rnb ) Dodas Residential Quarter By Way Of Addition And Alteration Of Bathroom And Kitchen. As Per Nit / Sbd. Submission Date for this Tender is 29-09-2021. Building Repair Tenders in Doda Jammu And Kashmir. Bidders can get complete Tender details and download the document.
Sl. No. | Item Description |
1 | Demolishing stone rubble masonry manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar |
2 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix) |
3 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : Of area of 3 sqm. and below |
4 | Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of : G.S. Sheet |
5 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: 1 meter from cutting edge All kinds of soil : |
6 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) |
7 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
8 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
9 | Random Rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including levelling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) and curing complete at window sills, ceiling level and the like:Cement mortar 1:6 (1 Cement : 6 coarse sand) |
10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
11 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete aboveplinth levelThermo-Mechanically Treated bars of grade Fe-500D or more. |
12 | 20mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand) |
13 | 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
14 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
15 | Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
16 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab over 0.5 sqm) (18 mm thick) |
17 | Providing and fixing cupboard shutters 25mm thick, with pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked exterior grade (Grade I Type II) having one side decorative lamination and other side a balancing lamination including second class teak wood lipping of 25mm widex12mm thick with necessary screws and bright finished stainless steel piano hinges complete as per directions of Engineer- in-charge |
18 | Providing and fixing sliding arrangement in racks/cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminum channel section (the payment for C or E channel shall be made separately) |
19 | Providing and fixing powder coated telescopic drawer channels 300mm long with necessary screws etc. complete as per directions of engineer-in-charge |
20 | Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters including fixing with necessary screws etc. complete.Double strip (Horizontal type) |
21 | Providing and fixing bright finished brass handles with screws etc. complete : 100 mm |
22 | Providing and fixing of PVC panelling of approved quality with frame work all complete |
23 | Providing and fixing M.S tubular frames for doors, windows, ventilators and cupboard with rectangular /L-type sections, made of 1.60 mm thick M.S Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10cm of C.C. 1:3:6 (1cement : 3 coarse sand :6 graded stone aggregate 20mm nominal size) . |
24 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). Second class deodar wood (30 mm) |
25 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Particle Board 12mm thick Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS : 12823 marked. |
26 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class Kail wood (30mm) |
27 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Second class Kail wood |
28 | Providing and fixing stainless steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I brackets and stainless steel plugs 40 mm including painting of fittings and brackets cuttings and making good thewalls wherever required. Kitchen sink without drain board 610 x 510 x 200 mm. |
29 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.: Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall: 15 mm dia. nominal bore |
30 | Providing and fixingwhite vitreous china pedestal tpe water closet(European type W.C pan) with seat and lid, 10 litre low level white PVC flusing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittins and fixtures complete, including cutting and making good the walls and floors wherever required: WC pan with ISI marked white solid plastic seat and lid. |
31 | Providing and fixing wash basin with C.I brackets, 15 mm dia CP brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: -White Vitreous China Wash basin size 550 x 400 mm with a 15 mm CP brass single hole basin mixer. |
32 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings |
33 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
34 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 |
35 | Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg. |
36 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 |
37 | Providing and fixing of mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frome of approved make and shade with 6mm thick hard board backing. Rectangular shape 453 x 357 mm. |
38 | Providing and fixing 600 x 120 x 5 mm glass shelf with edges round off supported on anodized aluminum angle frame with CP brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. |
39 | Providing and fixing 100 mm sand cast iron grating for gully trap. |
40 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
41 | Providing and fxing of PVC pipes fitting all Complete |
42 | Plain bend ofsize 100 mm dia |
43 | Door bend of size 100 mm dia |
44 | Plain bend of size 75 mm dia |
45 | Door bend of size 75 mm dia |
46 | Floor traps and P-Trap |
47 | PVC pipe of dia 100 mm |
48 | PVC pipe of dia 75 mm |
49 | Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
50 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
51 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work. |
52 | Distempering with 1st quality Acrylic/oil bound washable distemper (ready-made) having VOC content less than 50 grams/ litre of approved manufacturer and of required shade and colour complete as per manufacturers’ specifications, one or more coats on old work |
53 | Finishing walls with water proofing cement paint of required shade:Old work (one or more coats applied @ 2.20 kg/10sqm) complete |
54 | Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :250x16 mm |
55 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
56 | 200x10 mm |
57 | 100x10 mm |
58 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. |
59 | 125 mm |
60 | 100 mm |
61 | Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete: flexible pipe |
62 | Providing and fixing of 8 mm dia C.P / S.S jet with flexible tube upto 1 mtr long with S.S triangular plate to Europwan type W.C of quality and make as approved by engineer in charge. |
63 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangements of approved quality and colour 600 mm long towel rail with total length of 645mm, 78 mmwide and effective height of 88 mm weighing not less than 190 grams. |
64 | Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms. |
65 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms. |
66 | Providing and fixing 15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 |
67 | Labour required for fixing of window after fabrication from old window and lifting of mulba. |
68 | Carpenter |
69 | Mazdoor |
70 | Centering and shuttering including strutting, propping etc. and removal of form for: |
71 | Foundations, footings, bases of columns etc. for mass concrete. |
72 | Suspended floors, roofs, landings, balconies and access platforms. |
73 | Carriage of Material by MT |
74 | Carriage of Sand avg. lead of 22 km by MT |
75 | Carriage of Bajree (below 40 mm ) avg. lead of 10 km by MT |
76 | Carriage of Bajree (Above 40 mm ) avg. lead of 05 km by MT |
77 | Carriage of Mulba avg. lead of 02 km by engaging oneload carrier / trolly. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail