}

Supply Of Godrej Furniture Office And Teaching Work Apsu Rewa Supply Of Godrej Furniture Office And Teaching Work Apsu Rewa, REWA-Madhya Pradesh

Awadhesh Pratap Singh University has published Supply Of Godrej Furniture Office And Teaching Work Apsu Rewa Supply Of Godrej Furniture Office And Teaching Work Apsu Rewa. Submission Date for this Tender is 23-08-2021. Furnitures Tenders in REWA Madhya Pradesh. Bidders can get complete Tender details and download the document.




Tender Notice

28723280
Supply Of Godrej Furniture Office And Teaching Work Apsu Rewa Supply Of Godrej Furniture Office And Teaching Work Apsu Rewa
Open Tender
Indian
Madhya Pradesh
REWA
23-08-2021

Tender Details

Supply Of Godrej Furniture Office And Teaching Work Apsu Rewa Supply Of Godrej Furniture Office And Teaching Work Apsu Rewa

Key Value

Document Fees
INR 2000 /-
EMD
INR 50000.0 /-
Tender Value
Refer document

BOQ Items

Name of Work :Supply of Godrej Furniture Office and Teaching workAPSU Rewa
Sl. No. Item Description
1Schoolar 1048:- W Desk Cum Bench size shall be1048 Width mmx 895 Depth mmx 750 Height mm. Top & Seat Panel shall be18 mmthick PLB(pre - laminated board )withBack panelshall be 18 mm thick PLT .The Understructure shall beMSSQ tubes of size25.4 mmx 1.2 mm Plus there shall also be a storageShelf .
2Genii :-Desk-Top Panel-All panels are made from 18mm thk Pre-laminated twin board (E1/P2 GRADE) with PVC edge banding on all sides.The panels have cornersrounded for safety usage.Desk-Top Panel-All panels are made from 18mm thk Pre-laminated Compact Laminated Board with Decorative Paper on both sides (AS PER IS 2046: 1995) The Panels have corners rounded for safety usage .Understructure - All side metal frames and cross connectors are made from combination of 25.4 x1.2 mm thk(approx. 18 SWG) Round ERW tubes ,31.8 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes and 28.6 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes(As per IS:7138) which are welded together.The Welded structures and cross connectors are coated with min. 45 micron thickness of epoxy polyester coating.Back supports which are provided at the rear back are made of 50.8 x 25.4 x 1.2 mm thk(approx. 18 SWG) rectangular ERW tubes(As per IS:7138).The tubes are coated with min. 45 micron thickness of epoxy polyester coating.The storage shelves are made from 0.6 mm thk MS sheet(As per IS:513) fixed below the radesk top panel and are coated with min. 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. They are made from 2 mm thk MS sheet(As per IS:513) and are coated with min. 45 micron thickness of epoxy polyester coating.The understructure is assembled using M6 trilobular screws(As per DIN 7500)with Zn blue plating.Compact Laminate seat and back panels are assembled using M6 Counter sunk Trilobular screws(as per DIN 7500) with Zn Black Plating (As per IS 1573:1986)Spacers Are provided on th top of round tubes for wooden panels fixing. They are made of made Glass filled (30%)Plastic Caps made of PP copolymer(3530 Grade) are also provided on the rear frames adding more aestheic value to the product.M6 high tensile TVS make bolt(Class 8.8) with glasss filled nylon level adjustors are provided at the bottom of understructure to take care of unevenness in floor with height adjustment of approx 15mm.
3Enterprise 1350 Table:- without CPU Hanger size shall be 1350Width mmx 750Depth mmx 728 Height mm . Top shall be18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster)and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) .
4Eari High Back chair :-SEAT/BACK ASSEMBLY: The seat and back should bemade up of 1.2 ±0..1 cm. thick hot pressed plywood and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should bedesigned with contoured lumbar support for extra comfort.BACK SIZE: 49.5cm. (W) X 69.5cm. (H)SEAT SIZE: 49.5cm. (W) X 43.0cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should bemoulded with density =45+1-2 kg/m3 and hardness load 16 ± 2 kgffor 25% compression.ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore Hardness and reinforced with M.S. insert. The armrests should bescratch and weather resistant tant. The armrests should befitted to the seat with seat armrest connecting bracket made of 0.3 ±0.022cm. thk. HR steel. CENTRE PIVOT mechanism):The center pivot mechanism should bedesigned with the following features:360° revolving type.17° ±2°maximum tilt on pivot at centre.Tilt tension adjustment.Upright position locking.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLY: The bellow should be3 piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY: The pedestal should beinjection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel. castors. The pedestal should be66.3 ±0.5cm.(76.3 ±1.0 cm with castors).TWIN WHEEL CASTORS: The twin wheel castors should beinjection moulded in Black Nylon Overall Dimensions of ChairSeat Height - min 43.0 to max 54.0cm.Height - min100.5 to max 111.5cm.Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm.
5Eari visitor :-SEAT/BACK ASSEMBLY: The seat and back should bemade up of 1.2 ±0..1 cm. thick hot pressed plywood and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should bedesigned with contoured lumbar support for extra comfort.BACK SIZE: 49.5cm. (W) X 45.5cm. (H)SEAT SIZE: 49.5cm. (W) X 43.0cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should bemoulded with density =45+1-2 kg/m3 and hardness load 16 ± 2 kgffor 25% compression. ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore Hardness and reinforced with M.S. insert. The armrests should bescratch and weather resistant tant. The armrests should befitted to the seat with seat armrest connecting bracket made of 0.3 ±0.022cm. thk. HR steel.FIXED TYPE mechanism: The fixed type mechanism should be without back tilt. TUBULAR UNDERSTRUCTURE: The understructure should bemade ofØ2.54 2.54±0.03cm.x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated (DFT 40-60microns) Overall Dimensions of ChairSeat Height - 45.0cm.Height -84.0cm. Width & Depth of Chair as measured from pedestal - Width-55.0 cm and Depth-58.0 cm.
6Primium Executive chair :-SEAT/BACK ASSEMBLY: The seat and back should bemade up of1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around.The back foam should bedesigned with contoured lumbar support for extra comfort.MID BACK SIZE49.0 cm. (W) x 47.0 cm. (H)SEAT SIZE 49.0 cm. (W) x 44.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should bemoulded with density = 45 ±2 kg/m3/ and hardness load 16 ± 2 kgffor 25% compression.TUBULAR FRAME: The tubular frame should becantilever type & made of Ø 2.54 ±0.03cmx 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns ). Overall Dimensions of ChairSeat Height - 44.0cm.Height -80.5cm.Width & Depth of Chair as measured from pedestal - Width-55.0cm and Depth61.0 cm.
7Primum excutive chair :- SEAT/BACK ASSEMBLY: The seat and back should bemade up of1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around.The back foam should bedesigned with contoured lumbar support for extra comfort.HIGH BACK SIZE49.0 cm. (W) x 71.0 cm. (H)SEAT SIZE 49.0 cm. (W) x 44.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should bemoulded with density = 45 ±2 kg/m3/ and hardness load 16 ± 2 kgffor 25% compression.ARMRESTS :The one-piece armrests made of black integral skin polyurethane with 50-70 Shore ‘A’ Hardness and reinforced with M.S. insert.The armrests should bescratch and weather resistant.The armrests should befitted to the seat with seat/armrest connecting strip assembly made of0.5 ± 0.05 cm. thk. HR steel.CENTER TILT mechanism: The mechanism should bedesigned with the following features: 360° revolving type. 17°±2° maximum tilt on pivot at center Upright position locking Tilt tension adjustment.PNEUMATIC HEIGHADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLY: The bellow should be3 piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY: The pedestal should beinjection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal should be66.3 ±0.5cm.(76.3 ±1.0 cm with castors).TWIN WHEEL CASTORS:The twin wheel castors should beinjection moulded in Black Nylon.Overall Dimensions of ChairSeat Height - min 41.0to max 53.0cm.Height - min 100.0 to max 112.0cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.
8Economy visitor chair :- SEAT/BACK ASSEMBLY: The seat and back should bemade up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with changeable fabric upholstery covers and moulded Polyurethane foam, together with moulded back-spine cover. The back foam should bedesigned with contoured lumbar support for extra comfort. BACK SIZE: 42.0cm. (W) X 46.0cm. (H)SEAT SIZE: 47.0cm. (W) X 50.0cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR Polyurethane foam should bemoulded with density = 45 +/-2 kg/m3 and Hardness load 16 ± 2 kgffor 25% compression.ARMRESTS: The armrests should bemade of black integral skin Polyurethane wtih 50-70 Shore "A" Hardness and reinforced with M.S. insert. The P.U. armrests should bethen fixed to black powder-coated (DFT 40-60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. HR steel and fitted with claddings made of injection moulded Polypropylene.FIXED TYPE mechanism: The fixed type mechanism should be without back tilt. SPINE COVER: The spine cover should beinjection moulded in black co-polymer Polypropylene.TUBULAR UNDERSTRUCTURE: The understructure should bemade of 0 2.54 +0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns }. Overall Dimensions of ChairSeat Height - 45.0cm.Height - 88.0cm.Width & Depth of Chair as measured from pedestal - Width-59.0 cm and Depth-58.0 cm.
9Lab Stool :- SEAT ASSEMBLY: The seat should bemade up of 1.2±0.1cm thick flat plywood and with moulded Polyurethane foam and should be .upholstered with replaceable synthetic leather covers. SEAT SIZE: Diameter 40.0 cmADJUSTMENTS: 360° Revolving typeHIGH RESILIENCE (HR) POLYURETHANE FOAM:The_HR.polyurethane foam should be _moulded with density = 45 +1-2 kg/m3 and Hardness load 16 ± 2 kgffor 25% compression. HEIGHT ADJUSTMENT: The manual height adjustment should bevery easy to operate with a help of a knob.. It can be easily locked at the most comfortable position. PEDESTAL ASSEMBLY: The five-prong pedestal should befabricated from 0.2 ± 0.02 cm thick HR sheet( should be: DD 10791 HR ), powder coated ( OFT 40-60 microns )and fitted with an injection moulded blackPolypropylene Hub Cap and 5 nos. twin wheel castors. The pedestal should be55.0±0.5cm pitch-circle diameter (65.0±1.0cm with castors)TWIN WHEEL CASTORS: The twin wheel castors should beinjection moulded in Black Nylon Overall dimensions shall be Width- 65.0cm Depth- 65.0 cmSeat Height- 45.0 to 56.5cm
10Nano parch:- CROSS BEAM: It should bemade up of black powder coated rectangularM.S.ERW tube having 8.0 ± 0.03 cm x 4.0 ± 0.03 cm x 0.2 ± 0.014 cm size. LEG AND ARMREST: It should bechrome plated made of cold rolled steel with 0.12 ± 0.013 cm thinkness. SEAT/BACK SHELL: It should bepowder-coated perforated shell made from cold rolled M.S. sheet (DIN1623 Partl ST-12 Grade) 0.14 ± 0.013 cm thickness.The Side Bar should bemade of Chrome plated solid steel 3.0 ± 0.03 cm x 1.2 ± 0.3 cm with fluting and plastic inserts. The Shell should beassembled on the Cross Beam with help of M8 Bolts (Per Seat - 8 nos. Seat to Bracket and 4nos. Bracket to Cross Beam). Overall Dimensions Seat Height - 40.0cm, Height - 67.5 cm, Width & Depth of Chair as- Width-163.0cm and Depth-57.0 cm.
11Table - T 8:- size shall be1199Widthx 590 Depthx 735Height . The top panels shall be made from 18 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides . Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall be dia. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube .Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mmthick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS . Also there should be 10 lever cam lock plus handles built in plastic.
12Table - T 9:-size shall be1365Widthx 680Depthx 735Height . The top panels shall be made from 18 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides . Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall be dia. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube .Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mmthick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS . Also there should be 10 lever cam lock plus handles built in plastic.
13Table - T 104:- size shall be1665Widthx 900 Depthx 750 Height . The top panels shall be made from 25 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides . Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall besq. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube .Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mmthick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS . Also there should be 10 lever cam lock plus handles built in plastic.
14Stylo:- size shall be1200Width mmx 600 Depth mmx 750 Height mm . Table top shall be 18 mm PPB with 35 KGS , shelf shall be 12.5 KGS drawer shall be 506 KGS. The table top shall be 18 mm prelam particle board , 3 mm prelam MDF board. Metal parts shall be BM Slide For Keyboard plus castor mounting table plus locking bracket plus angle clit . Hardware shall be Screw , KD fitting , Wooden Dowel , PVC ibserts. Construction shall be KD fitting , Wooden dowel & Angle Clit.
15CH1007 chair :-SEAT/BACK ASSEMBLY: The seat and back should bemade from 1.0±0.1cm. thk. hot pressed moshould be ture resistant tant.commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H)SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should bemoulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgffor 25% compression. UNDERSTRUCTURE ASSEMBLY: The understructure assembly should bea cantilever type mainframe made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated--( DFT 40-60 microns ). ARMREST ASSEMBLY: The armrests should bemade in twin tube form using 0 1.58cm. (5/8") x 0.16 ±0.0128cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns ). Overall Dimensions of ChairSeat Height - 46.0 cm.Height - 82.5cm. Width & Depth of Chair as measured from base - Width-54.0cm and Depth-59.5 cm.
16CH1018 chair :- SEAT/BACK ASSEMBLY: The seat and back should bemade from 1.0±0.1cm. thk. hot pressed moshould be ture resistant tant.commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H)SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should bemoulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgffor 25% compression. UNDERSTRUCTURE ASSEMBLY: The understructure assembly should bea cantilever type mainframe made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated--( DFT 40-60 microns )Overall Dimensions of ChairSeat Height - 45.5 cm. Height - 78.5cm. Width & Depth of Chair as measured from base - Width-52.0cm and Depth-60.5 cm.
17PCH7046 chair :- SEAT/BACK ASSEMBLY: The seat and back should bemade from 1.2 ±0.1 cm.. thk. hot pressedplywoodmethod described in.and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam should bedesigned with contoured lumbar support for extra comfort.SEAT SIZE: 45.0cm(W) x 42.0cm.(D)BACK SIZE: 40.0cm(W) x 47.0cm.(H) SEAT /BACK COVERS: The seat and back covers should beinjection moulded in black Co-polymer Polypropylene HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR polyurethane foam should bemoulded with density = 45 +/-21(g/neand_hardness load 16_± 2 kgffor 25%_compression.ARMREST ASSEMBLY (FOR 7046R): The one-piece armrests should beinjection moulded from black Nylon. The armrests should befitted to the seat with armrest connecting brackets made of 0.5 ± 0.05 cm. thk. HR steel.PERMANENT CONTACT mechanism: The permanent contact mechanism should bedesigned with the following features 360° revolving type.14° ±2°maximum-back-tilt-only.Upright position locking.Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cmTELESCOPIC BELLOW ASSEMBLY: The bellow should be.3 piece telescopic type and injection moulded in black Polypropylene PEDESTAL ASSEMBLY: The pedestal should beinjection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal should be62.0 ±0.5cm. pitch-centre dia. (72.0 ±1.0cm with castors). TWIN WHEEL CASTORS: The twin wheel castors should beinjection moulded in Black NylonOverall Dimensions of ChairSeat Height - min 43.0 to max 54.0cm.Height - min87.5 to max 98.5cm.Width & Depth of Chair as measured from pedestal - Width-71.0 cm and Depth-71.0 cm.
18PCH7042 chair :-SEAT/BACK ASSEMBLY: The seat made from 1.2 ±0.1 cm. thk. hot pressed plywood and back should beinjection moulded from black Co-polymer Polypropylene upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam should bedesigned with contoured lumbar support for extra comfort.SEAT SIZE: 45.Ocm(W) x 42.0cm.(D)BACK SIZE: 39.0cm(W) x 38.0cm.(H)SEAT / BACK COVERS: The seat and back covers should beinjection moulded in black Co-polymer Polypropylene.HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR polyurethane foam should bemoulded withdensity = 45 +/-2 kg/m3 and Hardness load 16_± 2_kgf as_per should be :7888 for 25% compression.ARMREST ASSEMBLY: The one-piece armrests should beinjection moulded from black Nylon. The armrests should befitted to the seat with armrest connecting brackets made of 0.5 ± 0.05 cm. thk. HR steel.PERMANENT CONTACT mechanism: The permanent contact mechanism should bedesigned with the following features:360° revolving type.14° ±2°maximum back-tilt onlyUpright, position locking.Tilt tension adjustment.PNEUMATIC HEIGHT. ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLY: The bellow should be3 piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY: The pedestal should beinjection moulded in black 30% glass-filled Nylon and fitted with 5 nos.: twin wheel castors. The pedestal should be62.0 ±0.5cm. pitch-centre dia. (72.0 ±1.0cm with castors).TWIN WHEEL CASTORS: The twin wheel castors should beinjection moulded in Black Nylon.Overall Dimensions of ChairSeat Height - min 43.0 to max 54.0cm.Height - min81.5 to max 92.5cm.Width & Depth of Chair as measured from pedestal - Width-71.0 cm and Depth-71.0 cm.
194 Door Book Case:- shall have the configuration of 914mm(W)x320mm(D)x1742mm(H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid Knock Down Construction. The Top Pannel, Back Pannel and Side Pannel are made from 0.7mm high yield CRCA and other components from 0.8mm CRCA.Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of max 80 Kg. The 4vDoor Book Case shall have 18mm PLB Top straight edge with PVC lipping. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).
20Storwel plain:- shall have an overall size of916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.
21Vertical Filing Cabinets:- whcih use less floor space. Size of 4 Drawer VFC shall be 1320mm(H) X 470mm(W) X 620mm(D). All the components shall be made of CRCA . It should have 1 Point Locking Mechanism and a Rigid Knock Down Construction. The Top, Side & Drawer Front thickness should be 0.7mm. The Frames, Drawer-inside cover and Side Back Side thickness should be 0.6mm. The Back, Bottom and Drawer thickness should be 0.5mm. Easy to grip Full length Recess Handle shall be integrated into Metal Drawer for easy pull out convenience. There shall be a Snap on type plastic label holder on Drawer Fronts. In addition, 28 ‘Ezee’ / ‘Visa’ files (Foolscap) from front to back of thickness 20mm per drawer can be hanged in VFC. The Centralized locking System shall be provided alongwith Shooting Bolt Mechanism and 10 Lever Cam Lock. The VFC should have anti-tipping arrangement which ensures that when one drawer is opened for use, it does not allow other drawers to be opened. The High Quality Precision Ball Slide shall be provided with Drawer Load capacity of max 40 kg and UDL for 75,000 cycles (BS). Plain Triangular plate pop should be riveted at the bottom corners for rigidity. Optional Accessories like Drawer Partition and Cradle for hanging A4 file folders front to back should also be available. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).
22Glass Door Storwel:- shall have an overall size of916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The glass door storwel shall have a brass handle and a 2 way locking mechanism with shooting bolt .It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (,/- 10). Plenty of colour options and shelving options shall be available.
23Storwel Minor plain shall have an overall size of 765mm(W)x440mm(D)x1270mm(H) with welded construction. It should have the shelf thickness of 0.7mm, Back thickness of 0.8mm and all other components shall be 0.9mm thick. These components are made of CRCA ‘D’grade high yield strength as per IS:513.The storwel Minor should have a Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting (3 nos.) which shall have a Uniformly Distributed Load capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (,/- 10).
24Quilt PU Foam & Bonded Foam Thickness 10 Cm Usable To Both Side Cushion Scale 3.9 Support Scale 5.9
25Cignus table :- Work Surface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management.Modesty Panel :Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to topUnderstructure : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Hinge Door Storage: Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top. Handle is provided for ease of opening. Storage is provided with lock for security.
26Finesse Table - 5026size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading.Finesse ERU -3616 LHS size shall be 1050 Widthx 450 Depthx 705 Height. The top ofFinesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading.
27Unwind:- The Seat and Back should bemade up of injection moulded indoor grade PolyPropylene compound SEAT SIZE : 52.5 cm. (W) x 53.2 cm. (D) BACK SIZE : 51.6 cm. (W) x 40.5 cm. (H) The powder coated ( DFT 50±10 microns ) welded tubular frame should bemade from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. The shoes should bemade of indoor grade PolyPropylene compound and snap fitted with tubular frame.
28Winner:- size shall be600 Width mmx 400 Depth mmx 740 Height mm . Top shall have desk panels of 18 mm thick Pre - Laminated boards with PVC banding on all sides . The Understructure shall be made of 19.05 x 1.25 mm thick Powder coated ERW tubes at base . The tubes are closed with plastic caps . The storage shelf shall be made from 0.6 mm thick powder coated MS sheet which is affixed below the desktop . Hooks shall be provided on either side of the vertical frames of the desk, for hanging bags / bottles . They shall be made from 6.0 mm dia. MS rods . There shall also be Level adjustors to take care of uneveness in floor .
29Insight 1800 W :-size shall be1800 Width mmx 900 Depth mmx 740 Height mm . The top shall be 25 mm thick PLB with 2 mm thick PVCEdge Beading plus the Understructure shall be having C - Frames 1.6 mm thick MS supporting the top . The Legs shall be of dia. 38.1 x 1.6 mm thick MS ERW tube .
30Diva chair:- 1)SEAT/BACK FRAME ASSEMBLY: The seat and back should bemade of 0.1 ±0.012 cm thick CR steel perforated sheets which should bewelded to a seat/back frame assembly made of 0 1.9 ±0.02cm x 0.16 ±0.0128 cm thk MS ERW tube. Connecting Strips made of 0.5cm thick HR steel should bewelded to the structure. The mounting base subassembly made up of 0 1.9 ±0.02cm x 0.16 ±0.0128 cm thk & C-channel made of, 0.315±0.022cm HR steel welded to connecting strip for assembly with the connecting beam.SEAT. SIZE: 39.2cm. (W) x 41.5cm.(D) (Approx.)BACK SIZE:39.5cm. (W) x 21.5cm.(H) (Approx.)2)CONNECTING BEAM ASSEMBLY: It should bemade up of 5.0 ±0.03 cm x 5.0 ±0.03 cm x 0.16 ±0.0128 cm thk. M.S.E.R.W Squshould betube. The connecting beam should bepowder coated ( DFT 40-60 microns ). The ends of the Beam should beclosed with L-shaped plastic end cap made from PP material. The connecting beam assembly should bepowder coated (DFT 40-60 microns).3)LEG ASSEMBLY: It should bemade up of 5.0 ±0.03 cm x 5.0 ±0.03 cm x0.16 ±0.0128 cm thk. M.S.E.R.W Squshould betube. and 0 3.175 ±0.03 cm x 0.2 ±0.016 cm thk M.S.E.R.W tube welded together toC-channel made of 0.2 ±0.018 cm thk CR steel. Plastic End caps should befitted to Legs. The leg assembly should bepowder coated ( DFT 40-60 microns).
31Jinnerio(1.SEATER):Overall Size :Width: 111cm Depth : 93.5cmHeight : 89cm Seating Height : 47.5cm. (3 SEATER):Overall Size :Width: 211cm Depth : 93.5cmHeight : 89cm Seating Height : 47.5cm. stitching: thread- polyester. pitch- 5 stitch per inch( pitch of thread i.e. stitch per inch). leather/pvc/fabric: (pu/pvc/cotton/ polyester/ composite)- fabric:d3/d5/d6 leather look fabric100%polyester. thickness (mm) :0.9mm. weight (gsm) : 250g/m2. tensile strength {wrap/weft} (kg/cm) :nil. bursting strength (kg/cm2) :nil. colour fastness to rubbing {dry /wet} (scale 1-5) :grade4. frame material (tropical wood / pine wood/ rubber wood): solid plywood frame. moisture content ( 10 – 12 %) : less than12%. thickness of plywood used(mm) :9mm/ 12mm/18mm/ 30mm.standard of plywood used: {required standard : is 303 commercial plywood}. seat foam: (density, type)- thickness (mm) :100mm. density (kg/m3):30. type of foam (virgin/composite/moulded/ slabstock) :seat foam:5cm pure foam 3030(30density)+5cm rebond foam. covering :decron sheet spec.150g70g. back foam: (density, type)- solid decron 7d/64mm. belt/ webbing material:nylon webbing- width of belt (mm) :back:45mm/seat:50mm.
32Periodical Display Rack:- MetalOverall Dimensions of All Steel Periodical DisplayRack shall be 900mm(W)x450mm(D)x1830mm(H). Rigid Knockdown construction ,Panels shall be made from CRCA 0.6 mm thick and front frame shall be made from CRCA 0.8 mm thick . CRCA D grade as per IS 513 . There shall be 5 level racks , Display tray shall be suitable for fullscape size magazines,periodicals, aesthetically appealing metal tray at an angle for easy viewing . Receding facility to access the storage behind . Sliding on plastic rollers . Behind storage shelving each of 5 level has a behind storage shelf . Uniformly Distributed Load capacity per each shelf is 40 kg . Leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns .
33Ace chair:-SEAT/BACK ASSEMBLY:The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The NetBack should bemade up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn.Full Back Size: 46.5 cm. (W) x 60.0 cm. (H)Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should bemoulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgffor 25% compression. BACK SPINE: The support spine should bemade up of High Pressure Die cast polished hed Aluminum.ARMRESTS : The armrest should behaving two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should beprovided in Aluminum structure of armrest which should beconnected to Aluminum Back spine and should beoperated by button. The depth adjustment should beprovided in pad which should befixed to armrest structure. Armrest Top should bemade up of PU molded over plastic inner.ACTIVE BIO-SYNCHRO mechanism:The adjustable tilting mechanism should bedesigned with the following features:360° revolving type Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort Tilt tension adjustment can be operated in seating position 5 position Tilt limiter giving option of variable tilt angle to the chair Seat / back tilting ratio of 1:2The mechanism housing should bemade up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron)SEAT DEPTH ADJUSTMENT: Seat depth adjustment should beintegrated in the seat through a sliding mechanism. Seat depth adjustment range should beof 3.75±0.1 cmLUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consistof lumbar spine (material-Glass Fiber Filled Nylon) which should befixed toAluminum Back spine. The Lumbar pad (material- Poly Propylene) should befixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustmentof 5.0±0.5cmPNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm.PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should beHigh Pressure Die cast polishedAluminum and fitted with 5 nos. twin wheel castors. The pedestal should be65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTORS:The twin wheel castors should beinjection moulded in black PP having 6.0± 0.1cm wheel Diameter.The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polyster fabric.Upholstered inner should befixed to Neckrest cover.Neckrest should befixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2°  Overall Dimensions of Chair Seat Height - min 45.5 to max 55.5cm.Height - min 95.5 to max 105.5 cm. Width & Depth of Chair as measured from pedestal - Width-75.0 cm and Depth-75.0 cm
34Thrive with Headrest :- The seat is made up of 1.4± 0.1 chick hot - press 4 plywood upholstered with fabric and moulded polyurethane foam. It has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. SEAT SIZE: 50.0cm (W)x 49.0cm(D).The Back is injection moulded in Glass filled Polyamide which is upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 6.0±0.1cm.BACKSIZE: 50.0cm(W) x68.0 cm(H).The polyurethane foam for seat is of density 55± 5kg/m3.The height adjustment armrest is made of Polyamide struture and polypropylene Housing with moulded PU armtop having a adjusted of 7.0+ 0.3 cm The inner tube of armrest is chrome plated. The mechanism is designed with the following features:• 360° revolving type.• Centre tilt Synchro• 3 position (including upright lock) giving option of variable tilt angle to the chair with anti shock feature. The Headrest is injection moulded din Glass Filled Polypropylene which is upholstered with foam and fabric has an adjustment of 6.0± 0.1cm & its assembled over the Full back chair. The pneumatic height adjustment has an adjustment stroke of 8.5+ ± 0.3cm.The pedestal is injection mouldedpolymide and fifted with 5 nos. twin wheel castors. The pedestal is 66.0+ 0.1cm wheel Diameter.The twin wheel castors are injection moulded in black Glass filled polyamide having 6.0±0.1cm wheel Diameter. The powder coated frame is made of Día2.8±0.03cm x0.2±0.02 cm the M.S. Round tube. The frame is fitted with plastic caps made of injection moulded glass filled Polypropylene. -76(W)* 76(D)* 100-109(H)* 45-54(SH).
351)Bliss 3 Seater:- SEAT/BACK FRAME ASSEMBLY: The seat and back should bemade of 0.1 ±0.012 cm thick CR steel perforated sheets which should bewelded to a seat/back frame assembly made of 0 1.9 ±0.02cm x 0.16 ±0.0128 cm thk MS ERW tube. Connecting Strips made of 0.5cm thick HR steel should bewelded to the structure. The mounting base subassembly made up of 0 1.9 ±0.02cm x 0.16 ±0.0128 cm thk & C-channel made of, 0.315±0.022cm HR steel welded to connecting strip for assembly with the connecting beam.SEAT. SIZE: 39.2cm. (W) x 41.5cm.(D) (Approx.)BACK SIZE:39.5cm. (W) x 21.5cm.(H) (Approx.)2)CONNECTING BEAM ASSEMBLY: It should bemade up of 5.0 ±0.03 cm x 5.0 ±0.03 cm x 0.16 ±0.0128 cm thk. M.S.E.R.W Squshould betube. The connecting beam should bepowder coated ( DFT 40-60 microns ). The ends of the Beam should beclosed with L-shaped plastic end cap made from PP material. The connecting beam assembly should bepowder coated (DFT 40-60 microns).3)LEG ASSEMBLY: It should bemade up of 5.0 ±0.03 cm x 5.0 ±0.03 cm x0.16 ±0.0128 cm thk. M.S.E.R.W Squshould betube. and 0 3.175 ±0.03 cm x 0.2 ±0.016 cm thk M.S.E.R.W tube welded together toC-channel made of 0.2 ±0.018 cm thk CR steel. Plastic End caps should befitted to Legs. The leg assembly should bepowder coated ( DFT 40-60 microns).
36Pulse chair :-SEAT/BACK ASSEMBLY: The seat should bemade up of 1.2 ± 0.1cm thk. hot pressed plywoodOCP-QLTA-PL14-18.The Back should bemade up of injection moulded glass filled nylon & upholstered using Net fabric with high tenacity yarn.SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D)BACK SIZE :45.0 cm. (W) x 65.3 cm. (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should bemoulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgffor 25% compression.3.ARMRESTS : The armrests have an Up-Down adjustment of 8.5 ± 0.5cm which should beprovided in armrest structure. Armrest Top has an integrated layer of Thermoplastic Elastomer (TPE). LUMBAR SUPPORT ASSEMBLY: The Lumbar support consshould be ts of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. FRONT PIVOT SYNCHRO mechanism: The adjustable tilting mechanism should bedesigned with the following features. 360° revolving type.Single point control. Front-pivot for tilt with feet resting on ground ensuring more comfort.Tilt tension adjustment.4-position locking with anti-shock feature.Seat/back tilting ratio of 1:2.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm.PEDESTAL ASSEMBLY: The pedestal should beinjection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia should beØ66.1 ± 0.5 cm (76.1 ± 1.0 cm. with castors).TWIN WHEEL CASTORS:The twin wheel castors should beinjection moulded in black Nylon.The Neckrest assembly consshould be t of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest should befixed to Back Assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ± 0.5 cm and rotation adjustment of overall 76°± 2°. The complete neckrest assembly should beretro fit to the main chair.
37Karina High Back:- SEAT/BACK ASSEMBLY: The seat is made up of 1.2 +0 1cm thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam The back is made up1.2 TO 1.0 cm thick hot pressed plywood measured as per QA method described inOCP-QLTA-P14-18 and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam The back ply and foam is designed with contoured lumber support for comfortable seating postureHIGH BACK SIZE 48.5 cm (W) X 76.0 cm (H)MID BACK SIZE 48.5 cm (W) X 64.5 cm (H)SEAT SIZE 51.0 cm (W) X 48.0 cm (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back is moulded with density = 45 +/-2 kg/m* and Hardness load 12 kgf as per IS 7888 for 25% compressionARMRESTS (ADJUSTABLE):The armrest top is moulded from polyurethane(PU) and mounted onto a drop lift adjustable type tubular armrest support made of 3.81 + 0.03 cm *0.02 + 0.1 cm thk M.S.E.R.W tube having chrome plated finish. The armrest height adjustable up to 6.5 + cm in 5 stepsKNEE TILT SYNCHRO MECHANISM WITH SEAT DEPTH ADJUSTMENT `360° revolving type Single point controlSingle point controlFront pivot for tilt with feet resting on ground ensuring more comfort Tilt tension adjustment4-position locking with anti-shock feature Seat back tilting ratio of 1.2Seat depth adjustment of 6.0 + 0.5 cm can be locked in 6 positions FRONT PIVOT SYNCHRO MECHANISM: The mechanism is designed with the following features360° revolving typeSingle point control Front pivot for tilt with feet resting on ground ensuring more comfort Tilt tension adjustment4-position locking with anti-shock featureknockdown condition vacations within +1.0 cmADJUSTABLE BACKREST: The back rest is connected to the mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0 + 0.5cm. and locked in 5 positions for the better lumbar support.PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 10.0 + 0.3 cm.PEDESTAL ASSEMBLY :The pedestal is fabricated from 0.2 + 0.02 cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.010.Scm. Pitch-center dia. (76.0 + 1.0 cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in black Nylon.High Back (W)76*(D)70.7*(H)103.5-120.5 cm (SH)47.5-57.5 cmMid Back (W)76.*(D)76*(H)93.4-110.4 (SH)47.5-57.5 cm
38Unlearn 2 Seater Laptop size shall be1350 Width mmx 600 Depth mmx 680 Height mm.Top shall be 25 mm thick , Base material shall be 25 mm thick pre-laminated particle board plus 2 mm thick PVC edge banding on straight outer edges . The Modesty shall be 18 mm thick its base material shall be 16 mm Plain particle board plus post - laminated with 0.6 mm top laminate on either side2 mm thick and 0.8 mm thick PVC edge banding of matching colour on outer edges of modesty . Legs shall be made from 1.6 mm Matt silver anodized aluminiumn extrusion . Legs assembeled together with 8 mm thick MS Powder coated plate at top . The base support plate is having provision for wire entry and glide fixing. The wire carrying is facilitated through the hollow space between two leg extrusions and the wires are concealed between removable rigid PVC extrusion in the leg . Max . 20 nos. of Dia 6 wires can be passed through the space between two leg extrusions . Table Support brackets shall be powder coated table support brackets made from 2 mm thick MS sheet provided for overall product stability . Stopper shall be powder coated made from 1.5 mm thick aluminium extrusion fixed with work - surface by powder coated stopper bracket made from 3 mm thick MS sheet . Both ends of Aluminium extrusion covered with plastic moulded end cap . The Grommet shall be made from plastic moulded components to facilitate access electrical / data / voice sockets access from top . The Switch Mounting tray shall be powder coated made from 0.8 mm and 2 mm thick MS sheet fitted with modesty through which cables can be passed .
39Beat Chair :-1. SEAT/BACK ASSEMBLY: The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 ; upholstered with synthetic leather over moulded High Resilience Polyurethane foam.HIGH BACK SIZE:51.8 cm. (W) x 75.2 cm. (H)MID BACK SIZE: 51.6 cm. (W) x 65.7 cm. (H) SEAT SIZE:49.0 cm. (W) x 51.4 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS: The adjustable armrest is designed with the following features :Up-Down adjustment– 8 steps (8.0±0.5cm range) Height adjustable armrest structure which is chrome plated & fitted with an armrest top. Fixed Armrest Topis PU moulded over metal insert.(A) FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designedwith the following features.360° revolving type. Single point control. Front-pivot for tilt with feet resting on ground ensuring more comfort. Tilt tension adjustment. 4-position locking with anti-shock feature. Seat/back tilting ratio of 1:2.( kB) BACK HEIGHT ADJUSTABILITY: Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for for High back and Mid back chair.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm.PEDESTAL ASSEMBLY WITH CASTORS:The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTOR: The twin wheel castors are injection moulded in black PP.OPTION OF SLIDING SEAT MECHANISM : Seat can be slide horizontaly as per user convenience. Stroke of seat slide is 5 cm. This option is available for revolving pedstal type of chair.
40Bravo High chair :-SEAT/BACK ASSEMBLY: The seat and back should bemade up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded Polyurethane foam. The back foam should bedesigned with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE 47.5 cm. (W) x 69.5 cm (H)SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM:The HR polyurethane foam should bemoulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgffor 25% compression. ARMRESTS :The one-piece armrests should beinjection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO mechanism: The mechanism should bedesigned with the following features: 360° revolving type. • Upright-position locking • Tilt tension adjustment • Seat/back tilting ratio of 1:3. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLYThe bellow should be3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY:The pedestal should beinjection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal should be66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). .TWIN WHEEL CASTORS:The twin wheel castors should beinjection moulded in Black Nylon.Overall Dimensions of ChairSeat Height - min 42.5 to max 54.5cm.Height - min97.0 to max 109.0cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.
41Zurina Side Table:-Overall Size : Depth - 461.0 mm Width - 460.0 mm Height - 510.0 mmMaterial :Body panels of Bed side table are made of 18 mm thickPrelaminated Particle Board .All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Drawer front & Door are made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trim fixed on to it. Hardware : The high quality hardware used like Roller slides, Hinges , minifix, dowels is of make Hettich.. Construction : Knock Down construction.Packets : 1 packet.Finish :. 18 mm thick Prelaminated Particle Board is in Maple shade
42Pillow:- L:425mm W:675mm
43Parto sofa :- (1seater)-92cm(w)*87cm(d)*78cm(h)*43cm(sh).(3 seater)-175cm(w)*87cm(d)*78cm(h)*43cm(sh).STITCHING: THREAD : Poly Proplin, PVC. Thickness (mm) : 0.9. Weight (GSM) : 575. FRAME MATERIALMoisture Content ( 10 – 12 %) : 16-20%. Thickness of Plywood used(mm) : 12mm & 18mm. SEAT FOAM: (DENSITY, TYPE)-Thickness (mm) : 69, 22 & 10 mm. Density (Kg/m3)- 32d. Type of Foam : Vergin Always / in some case Moulded - Dencity :- 48d. LEG MATERIAL: * Fixing of Leg :Woodscrew provided on frame in addition to M-8 / T-Nut * Material of leg - Plastic * Bush for Leg bottom : Pvc. Bush .BACK FOAM: (DENSITY, TYPE) -Thickness (mm) : 45 mm .Density (Kg/m3): 28 d .ARMREST FOAM: (DENSITY, TYPE) Thickness (mm) : 45 mm .Density (Kg/m3): 26 d
44Glaze Coffee Table :-Overall Size : Width : 110cm Depth : 60cm Height : 50cm Elegantly crafted inmetal combinationsfloat glass topThecenter table top is made of 110*60*50The packing speces of the table top is 1040x690x40mm. The leg of the Complete Metal Understructure
45WORKSTATIONS 900*600Providing and placing WISH panel & tile based modular workstation, with partition thickness as 52.4 mmthk and ht 1200 including powder coated aluminium trims.Tiles: Combination of top tiles are clear glass tile. Bottom tiles Plain metal.INTERMEDIATE BLOCKS Intermediate blocks are given in DL + Fabric finsh.Wire Management Wires shall be taken into the system through cable ducts from the junction oxes and it is carried upto the panels through concealed conduits inside the blocks.legs ometal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look.Worksurface out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900*600CPU trolley with castorsKBPT with mousetray plasticNote: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/ 40 mm of uneven flooring.
46Split Air Conditioners: 1.5 TonSplit Air Conditioners 5 Star Rating Inverter Technology ,Anti Bactarial Filter,Anti Microbial Self Cleaning Active CarbonFilter,Evaporator Coil Sensor,Silent Opration,Anti Corrosive Coating on Evaporator & Condensar100% Copper Condenser & Connecting Pipe,Heavy Duty Cooling AT 50 Digrey C,R 32 Eco Friendly Refrigerant,Anti Dust Filter,Tropicalized Compresser,Anti Dust Filter,Smart Diagnosis.10 Year Compresser Warranty
47Split Air Conditioners: -2 TonSplit Air Conditioners - 5 Star Rating Inverter Technology ,Anti Bactarial Filter,Anti Microbial Self Cleaning Active Carbon Filter,Evaporator Coil Sensor,Silent Opration,Anti- Corrosive Coating on Evaporator & Condensar100% Copper Condenser & Connecting Pipe,Heavy Duty CoolingAT 50 Digrey C,R-32 Eco Friendly Refrigerant,Anti- Dust Filter,Tropicalized Compresser,Anti Dust Filter,Smart Diagnosis.10 Year Compresser Warranty
48Refrigerators Single DoorSingle Door Refrigerators - 5 Star Rating, Size-251 LiterInverter Technology,Inverter Compresser Turbo Cool Technology,Largest Bottel Space,Largest Frezzer,24 Hour Bottel Cooling Retention.Low Starting Voltage-110V.,Runs On Home Inverter
49Deep Freezer Convertible Deep Freezer Size- 325 Ltr.R290 Eco Friendly Refrigerant,Convertible Technology,High Puf Thickness Anti Rust Technology,Anti Bactarial Gasket,05 Year Compresser Warranty Cooling Range- (-28 Digree)Fastest Cooling
50Migle Confrence Table ( Per Seater)- Worksurface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure : It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The producthas a knock-down construction.Plastic ABS access flap is provided for easy access to wires and cables. Work top isavailable in various shapes as shown above.Modesty Panel : Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It ismade of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns)Wire Management : An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated(DFT 40-60 microns) is used for flow of wires and cables. Provision to mount AnchorRoma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables ontoworktop and connect devices charger to power socket below worktop.
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail