Military Engineer Services-MES has published 8953 Spr T-658 And T-479 Special Repairs To Bldg No T-658 ( Mt Store ) , T-479 ( Jcos Living ) And Road Furniture At Zakhama Military Station. Submission Date for this Tender is 14-08-2021. Road furniture Tenders in AGE (I) Zakhama Nagaland. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 07-Aug-2021 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 14-08-2021 |
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal of debris out of MD land at the location decided by the Engineer-in-charge complete all as specified andas directed. |
| 2 | Demolition of stone slabs and tiles of any description of thickness in floors, aprons etc laid bedded and pointed in any mortar. and removing debries outside MD land at the location decided by the Engineer-in-charge complete all as specified and as directed. |
| 3 | Dismantling timber scantling 40 Sqcm and over in section, unframed work in any position,complete all as specified andas directed. |
| 4 | Dismantling of plain or corrugated steel sheeting,any gauge, thickness, including similar pattern roof covering.complete all as specified andas directed. |
| 5 | Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each, complete all as specified andas directed. |
| 6 | Taking down shutters of any description n.exc 1 Sqmeach.complete all as specified andas directed. |
| 7 | Taking down cementplaster on brick, concrete or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and removal of rubbish out side MD land at the location decided by the Engineer-in-charge complete all as specified andas directed. |
| 8 | Demolition of reed, lathing, single or double including battens and plaster or chicken wire lathing and removing unserviceable materials from site of work complete all as directed. complete all as specified andas directed. |
| 9 | Taking down plastering on lathing(other than wire-netting), without removing lathing, in lime mortar (one side only measured in cases where both sides are plastered) complete all as specified andas directed. |
| 10 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles. and removing debries outside MD land at the location decided by the Engineer-in-charge complete all as specified andas directed. |
| 11 | M&L for rendering 15mm thick in cement mortar (1:4)on fair faces of brick walling, even and smooth without using extra cementusing water proofing compound @ 3% by wt of cement surface finished with sponge finish complete all as specified and as directed(Note : WPC shall be measured and paid separately) |
| 12 | M & L for 15 mm thick rendering on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed. |
| 13 | Supply only water proofing compound ISI Marked, complete all as specified and directed. |
| 14 | M & L for 75 mm thick cement concrete (1:3:6) type C-2,using 40mmgraded stone aggregates as in sub base finished fair and even with out using extra cement complete all as specified and directed. |
| 15 | M&L for 40mm thk PCC (1:2:4) type B-0 using12.5mm graded agg as in finished Flooring Finishing cement concrete surface even and smooth, complete all as specified and directed. |
| 16 | M&L for 25mm thick PCC (1:2:4) type B-0 using(12.5mm graded stone aggregate) as in flooring for level course, complete all as specified and directed. |
| 17 | M&L for 15mm thick screed bed or bedding layer of cement mortar (1:4) for laying under floor finishes,complete all as specified and directed. |
| 18 | M&L for joint free Non skid ceramic tiles 7 to 8 mm thick (square/rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles.complete all as specified and directed. |
| 19 | All as per Item No 13 above hereinbefore butin skirting including necessary cutting of tiles. |
| 20 | M&L for second class hardwood as in scantlings clean sawn timber framed and fixed. complete all as specified and directed. |
| 21 | M & L for brick work with sub class "B" bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed. |
| 22 | M&L for brick work with sub class "B" bricks, straight or curved on plan to any radius built in CM 1:4 in half brick thick walls complete all as specified and directed. |
| 23 | M & L for RCC1:2:4 , type B-I (nominal mix) using 20 mm graded broken stone aggregate in cover slab (Note :Reinforement shall be measured and paid separately here in after) supported on wall n.exc 20 cm thick as in cover slab complete all as specified and directed. |
| 24 | Use & waste for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed. |
| 25 | M& L for Mild steel TMTbar 10 mm diaor above cut to length bent to shape required including cranking, bending spirally, hooking ends etc and binding withand including mild steel wire (annealed)not less than 0.90 mm dia or securing with clipscomplete all as specified and directed. |
| 26 | S & F GI wire netting 0.9mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and as directed. |
| 27 | M& L for Rendering 10mm thick in cement motar (1:3)on the `other" side of lathing, complete all as specified and as directed. |
| 28 | S&F 0.63 mm thick Galvanized, corrugated mild steel sheetingwith two corrugations side lap, fixed with L-type /J-typer or cranked hook bolts and washers, in roofs, etc with zinc coating 275 grade ,complete all as specified and directed. |
| 29 | Labour onlyfor refixing 0.63 mm thick Galvanized, corrugated mild steel sheetingwith two corrugations side lap, fixed with L-type , J-typer or cranked hook bolts and washers, in roofs, etc ,complete all as specified and directed. Note :NewL-type/J-typer or cranked hook bolts and washers required shall deemed to be includede in quoted rates |
| 30 | M&L for 20mm to 25mm thick IInd class HW weathering boarding, wrought both sides and edges shot and chamfered ( on exposed edges) ,rebated on thick edge to give 20mm laps. complete all as specified and directed |
| 31 | S&F mild steel wind tie bar for roof including securing nuts bolts and washers conforming to Fe.290 Gde- E-165.complete all as specified and directed |
| 32 | S&F 30 mm thick Flush shutters, solid core construction, with particle board core and and plywood face panels, commercial type on both sides with lipping/frame to match, complete all as specified and as directed. |
| 33 | S &F2nd class hardwood 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauze etc divided into squares, with plain, chamfered or rounded mitred and framing plain, chamfered or rounded, fitted with cut and metered beads for securing glass etc size of members of shutters as specified in SSR Part I Sec 8 clause 8.24 (a) |
| 34 | All as above as in windows shutters 30mm thickdivided into squares, with plain, chamfered or rounded , mitred or rebated sash barswith stiles and rails as specified in SSR part I section 8 clause 8.24 (b) . complete all as specified and directed |
| 35 | S & Fas in replacementmild steel galvanized iron wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 and fixed with tinned tacks or staples complete all as specified and as directed. |
| 36 | M&L for 3mm sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm each pane. Complete all as specified and directed. |
| 37 | M&L for 100 mm long Butt hinges med weight cold rolled mild steel and fixed.Complete all as specified and directed. |
| 38 | M&L 75mm long Butt hinges med weight cold rolled mild steel and fixed, Complete all as specified and directed. |
| 39 | S&F 150 mm longAluminium anodised barrel tower bolt of extruded section and fixed. Complete all as specified and directed. |
| 40 | S&F 100mm longAluminium anodised barrel tower bolt of extruded section and fixed. Complete all as specified and directed. |
| 41 | S& F150mm longextruded aluminium alloy handles, fabricated type, anodised and fixed. Complete all as specified and directed. |
| 42 | S & F100 mm long extruded aluminium alloy handles, fabricated type, anodised and fixed, Complete all as specified and directed. |
| 43 | S& F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section or cast aluminium alloy and fixed. Complete all as specified and directed. |
| 44 | S&F in repairs 300mm long mild steel, ordinary rat tail rod pattern springs including roller and roller plate, Complete all as specified and directed. |
| 45 | S & F 140mm long floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring fixed in floor, Complete all as specified and directed. |
| 46 | S&F 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all neacessary" labours ; articles nexc 200 cu.cm each.Complete all as specified and directed. |
| 47 | M&L in repairs. forPrelaminated Particle Board 18/19 mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancig white lamination, fixed with nailsfor pelmet boxes, complete all as specified and directed. |
| 48 | S & F in repairs 20mm dia mild steel chromium plated curtain rods with and including fixing socket complete all as specified and as directed. |
| 49 | M&L for preparation of old woodensurfaces and wood based materials of any description not otherwise described over 10 cm width or girth and applyingone coat of synthetic enamel paint complete all as specified and directed. |
| 50 | M&L for preparation of new wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.complete all as specified and directed |
| 51 | M&L for preparation of new painted surfaces of steel and iron work of any description over 10 cmwidth or girth not otherwise described andapplying two coat of synthetic enamel paint over a coat of redoxide on new surfaces in any tint complete all as specified and directed. |
| 52 | M&L for preparation of oldpainted surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described andapplying one coat of synthetic enamel paiintcomplete all as specified and directed. |
| 53 | M&Lfor preparation new plastered surfaces of walls and applying two coats of oil distemper over coat of primer, complete all as specified and directed. |
| 54 | M&L forpreparation new plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant paint complete all as specified and directed. |
| 55 | M&Lfor preparation old plastered surfaces of walls and applying one coats of oil distemper over existing surface, complete all as specified and directed. |
| 56 | M & L for 75 mm thickcement concrete (1:3:6) type C-2,using 40mmgraded stone aggregates as in plinth protection finished fair and even.complete all as specified and directed. |
| 57 | M&L for 15 mm thickscreed bed or bedding layer or mortar for laying floor finishes in Cement Mortar (1:6), complete all as specified and directed. |
| 58 | M&L for chequered cement concrete tile 25CM x 25CM x 19 to 20 mm thick with grey cement and no pigment set, jointed and pointed in neat cement slurry. complete all as specified and directed. |
| 59 | M& L for provinding cement concreter type C1(1:3:6) using 20mm stone aggregate asin lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directing. complete all as specified and directed. |
| 60 | Extra for forming fair finished drain or channel 20 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc.complete all as specified and directed. |
| 61 | Taking up or down steel tubing 15mm bore of pipe and connectionsincluding cleaning for refixing etc as required. complete all as specified and directed. |
| 62 | S&F tubes medium grade galvanised, with all fittings and fixed complete to walls or ceiling or laid in floors 15mm bore dia. complete all as specified and directed. |
| 63 | S&F in repairs Wash Basins,Vitreous China,white ,flat back,size 630 x 450mmincluding brackets and cutting for and pinning in ends of brackets or erecting standinclduingpillar tap cast copper alloy chromium plated fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot" or `Cold" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed .but exclusive of fixing of supply and waste pipe. complete all as specified and directed. |
| 64 | Supply only High density polyethlene (HDPE) pipe of pressure rating 6 Kgf / Sqcm 32mm dia. complete all as specified and directed. |
| 65 | S&F stop valves 15mm bore dia, cast copper alloy fancy type, chromium plated with long shank and cup concealed type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions in repairs. complete all as specified and directed. |
| 66 | S&FPVC connection450mm long complete all as specified and directed. |
| 67 | S & F of unit fixing of unit/ directional/ road sign board, single sided of hardened ACP sheet 3 mm thick fixed on both sides, PoP riveted to stainless steel square pipe 20 mm x 20 mm and overall size of frame 1200 x 900 mm frame supported with another frame made of 40 x 40 mm SS square pipe and 3 m long double legged stainless steel pipe 50 mm dia, 16 gauge (SS-304 Grade) and fixed with each other with SS clamps. The board is fully reflectorised with high intensity grade retro reflective tape of any colour Grade IV as per ASTM - D 4956-07 and lettering (any nos) loc map white colour duly computerised cut including arrow, signs, logos etc fixed over retro reflective tape. Board to be fixed on ground 450 mm deep with necessary cement concrete complete all as specified and directed. |
| 68 | Taking down carefully point wiring copper/aluminum (light, fan, socket complete) including unserviceable battens or from existing casing capping/conceal conduit including earth continuity wire and fittings such as switches, socket, ceiling roses,lamp holder etc and making good disturbed surfaces of wall/ceiling etc complete all as specified and directed. |
| 69 | M&L for point wiring with single core PVC insulated unsheathed multistranded copper conductor FRLS cable of size 1.5 Sqmm nominal area 1100 volt grade drawn through and including PVC casing-capping/conduit of suitable size with all fittings and accessories including PVC board with cover of suitable size for housing/mounting the switches/socket etc including 1.5 Sqmm PVC insulated unsheathed single core copper conductor as earth continuty wire connected to common earth dolly for one light/exhaust fan point control by one switch.one way compleate all as specified and directed. |
| 70 | All as per item No 2 above but for 3 pin, 5 Amp Socket on the same board. |
| 71 | All as per item No 2 above but for 3 pin,5 Amp Socket on independent board |
| 72 | S&F switch piano flush button single pole one way 5 Amp. complete all as specified and directed. |
| 73 | S&F LED bulk head luminaires 10 W 6000k Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head Back-lit LED luminaire comprising of high brightness LEDs. complete all as directed. Make-Havells Cat No.HEXAFT10WLED857SSYMBOPC or eqvt make. |
| 74 | S&F ceiling rose surface back light 65 x 25mm, two to three terminal. complete all as specified and directed. |
| 75 | M&L Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. |
| 76 | S&F Lumino LED lamps 10W W E27WBall lamp lumen output 1020 Im 3000K color tempcurrent 0.055 amps complete as directed by Engr in Charge. Make - Havells ordering code LHLDEBHEMD8X010 or eqvt make of philips, bajaj |
| 77 | Taking down old unserviceable light fitting of any type any rating complete all as specified and directed. |
| 78 | S&F LED T/L20 W, Fixture size (1150x25x40) mm (for 20 W), complete with batten and luminaries Make - Havells , Model No. LUMILINEPLUSBS20WLED865SPCSS or equivalent ad as per the technical spevifications given below . Note:LED used shall conform to IS- 16103: 2012 &IS-16101:2012 should be of SMD type only. ii. LED efficiency shall be greater than 100 lumens per Watt/ max latest efficacy available. iii. Colour rendering index (CRI: Greater than or equal to 70). iv. Min efficiency of driver: 85%. v. Power factor of complete fitting: Greater than 0.95. vi. Input Operating Voltage: 140 V to 277V AC. vii. In-built high and low voltage cut-offs: 140 V Low and 277 (high). viii. Short circuit, Over load protection. ix. Housing of luminaries: Pressure die-cast aluminum LM6/ADC 12/LM 24housing |
| 79 | Taking down old unserviceable DB/Main switchs incl MCBs wooden block of any size and type and removing complete all as specified and directed. |
| 80 | S&F PVC rectangular block of size 250x200x50mm depth complete all as specified and directed. |
| 81 | S&F PVC rectangular block of size 100x100x50mm depth complete all as specified and directed. |
| 82 | S&F sheet metal enclosure for DB when MCBto be used 4 way 200 amp rated bus bar, SPN 240V, double door complete all as specified and directed.. |
| 83 | S&F MCB Single pole and neutral 240 Volts, 6B92:B93-32. Amps, 10 A,C-series,Make -havells, cat No.DHMGCSNF006-032 or same as equivalent. |
| 84 | S&F MCB Single pole240 Volts, 6-32. Amps, 10 A,C-series,Make -havells, cat DHMGCSPF006-032 or same as equivalent. |
| 85 | Dismantling/taking down old burnt out u/s UG cable/sub main wiring of any size complete from locations where directed. complete all as specified and directed. |
| 86 | S&F 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor surved with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4 mm suspension wire, one twin core cable flat or rouind or 10 sq mm cable. complete all as specified and directed. |
| 87 | S&F submain wiring 2x6 sqmmalongwith earth wire 2x4 sqmm FRLS PVC insulated copper conductor, single core in surface/recesssed drawn in and including 4 sqmm earth, casing capping with fixtures. complete all as specified and directed. |
| 88 | Dismantling house service brackets, any type, complete all as specified and directed. |
| 89 | S&F House service bracket (Hook type) compleate with 3.0 meter long GI pipe 40 mm dia Med grade, two Nos 90 degree bends, MS hooks and stay or guy. complete all as specified and directed. |
| 90 | S&F building security light /street light, New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 , Ambient temp- 35° C,•Operating temperature: -10° C to +50° C , Operating voltage range: 140 V - 270 V, including mounting bracket etc and complete all as specified and directed.Make -Havells, Model :ENDURAPEARLSL20WLED757SASYTOPCMP or same as eqt make of bajaj/ phillips etc. |
| 91 | M&L Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm buried directly in ground vertically to depth not less than 2.25 mtr below ground level with top edge earth plate at a depth not less than 1.5 mtr below ground level, connected to galvanised earth lead wire 4.00mm dia by means of nuts, bolts, check nuts & washers made of galvanized iron or steel and connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1 pre-cast RCC cover slab 30cmx30cmx10cm with one handle for lifting made out of 8mm dia MS bar, watering pipe 20mm bore galvanized iron pipe (medium grade) with MS funnel for watering charcoal or coke and salt in alternate layers, necessary excavation and earth work in hard/dense soil complete all other accessories as shown on electrical plate No 3 of MES Sch Pt-I including taking down the existing,all as specified and directed. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
