Assam Electricity Grid Corporation Limited-AEGC has published Construction Of Res Residence At Karimganj Gss. Submission Date for this Tender is 07-07-2021. Building Work Tenders in Karimganj Assam. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Earth work in excavation for foundation trenches of walls retaining walls, footings of column, steps, septic tank etc. including refilling the quantity as necessary after ……………….. removal of surplus earth with all lead and lifts as directed and specified.(A) Up to a depth of 1.00 m below the existing ground level.(b) In hard soil. |
| 2 | Providing brick soling in foundation and under floorwith stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labourand materials and if necessary dewatering, complete. (a) Brick on flat soling. |
| 3 | Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).(a) In prop 1:3:6 aggregate by volume. |
| 4 | Supplying, fitting and fixing in position reinforcement bars conforming to relevant IS code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes ………………and placing in position with proper blocks, supports, chairs, spacers etc. complete. (up to 1st floor level).(b)Other ISI approved TMT reinforcement bar (SRMB/SAI/BISCON/Xtech) (For Assam Type Bldg., drain works,,retaining wall&boundary wall etc.(i) TATA/SAIL |
| 5 | Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0 M and removal of the same for in-situ reinforced concrete and plain concrete work in: |
| 6 | (ii) Using 25mm thick plank (For footing) |
| 7 | (ii) Using 25mm thick plank (For Tie Beam) |
| 8 | (ii) Using 25mm thick plank (For Column) |
| 9 | (ii) Using 25mm thick plank (For Lintel & Roof band) |
| 10 | Providing and laying Plain/Reinforced cement concrete works in prop 1:2:4 including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete works (shuttering where necessary shall be measured and paid separately).(I) Using mixture machine. |
| 11 | (A) In sub structure up to plinth level.(a) M15 or Prop 1:2:4 Foundation, footing, columns with base tie and plinth beam, pile cap, base, base slab…………. Not less than 100mm thick up to plinth level. |
| 12 | (B) in superstructure from plinth level upto 1st floor (a) M15 or Prop 1:2:4 |
| 13 | Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in sub-structure up to plinth level.(b) In proportion 1:4. |
| 14 | Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed. |
| 15 | 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paidseparately)(A) 112mm thick brick wall(a) In cement mortar in prop. 1:4 |
| 16 | Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.(c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading. |
| 17 | 15mm thick cement plaster in single coat on rough side of single or half brick wall for interior plastering up to Ist floor level including arises, internal rounded angles, not exceeding 80mm in girth and finished even and smooth including curing complete as directed.(b) In proportion 1:4 |
| 18 | Providing fitting, hoisting and fixing of roof trusses including purlins fabricated using circular hollow section confirming to relevant I.S. code, as per approved design and drawings including providing M.S. cleats, base plates, bolts and nuts and one coat of red oxide Zinc Chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc. for fixing ceiling joists as per design and drawing as directed.(b) using other ISI marked approved circular hollow section. |
| 19 | Supplying, fitting and fixing double leaf heavy duty iron gate, frame made from 40mm x 40mm x 6mm M.S. angle and with M.S. flat of 40mm x 6mm size as per approved design.Necessarylocking arrangement for temporary closing the gateand 2nos.( minimum) strong iron hinges of M.S bars and flat of same sizes on each leaf to be embedded in C.C brick pillers as necessary including a red oxide painting to all iron works as directed and specified.(Separate payment will be made for posts). |
| 20 | Providing roller to the gate including welding etc.complete. a) With 25mmx50mm (dia) roller |
| 21 | Providing Pre Painted Galvanized IronSheetRoofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement. (iv) 0.50 mm thick |
| 22 | Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing)at all levels including fitting and fixing self drilling, self tapping screws complete complete. TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement(iv) 0.50 mm thick |
| 23 | Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (b). With 1st class timber (Bonsum/ Sundi) |
| 24 | Providing, fitting and fixing factory made wooden panelleddoorswith panelinserts of 75mm to 50mm width and 12mm to 20mm thickness,joined together withcontinoustongue and groove joints glued together with Movicol or other approved adhesive leaving a vertical groove of7.5mm to 15mm between the inserts,the edges of panel inserts being feather tongue into styles and rails including providing three pairs of oxidised M.S butt hinges (100mm x75 mm x3.55mm) and furnishing with moulded timber beading of size 25mmx15mm around the panels complete as per drawing (moulded timber bead and all fittings except hinges to be paid separately). b) With 1st class local wood (Hollock / Gamari/Sundi/ Bonsum)(ii). 35 mm thick with panel inserts of 20mm thickness. |
| 25 | Providing, fitting and fixing steel windows/ ventilators (openable) of standard rolled steel sections as per relevant I.S. Code-1038 joints mitred and welded with 15mmx3mmx100mm lugs embedded in cement concrete block of M-10 grade including providing and fixing of projecting hinges (not more than 65mm and not less than 15mm wide) bolting device and steel handles, peg stays of 300mm long etc. complete as per drawing including applying a priming coat of red-lead paint. |
| 26 | Providing, fitting and fixing PVC door frame of Duroplast make DPF-5060 make suitable for DPS-3720 made from extruded PVC multichamber hollow section having dimensions of 50mmx60mm (Toletance + 1mm). Horizontal and vertical sections shall be joined by steel.................... |
| 27 | Providing, fitting and fixing 24mm/ 29mm thick polymer reinforced moulded PVC door shutters fixed to the chowkath with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid seperat(b) 29mm thick |
| 28 | Providing wood work in frame of false ceiling partitions etc.sawn, wrought, framed hoisted and fixed in positon with spikes, nails, M.S flat,angle/ cleats with bolt and nuts complete including kiricide oiling two coats to unexposed surfaces of the timber (M.S flats, angle cleats, and bolt and nuts required for flat, angle cleats wherever necessary shall be measured and paid separately). (b) With Gamari/ Bonsum/ Sundi |
| 29 | Supplying, fitting and fixing ceiling tiles of 10mm thick made from Duratuff medium density fibre board in size 1200mm x 1200mm x 10mm with Sal wood timber frame (to be measuredand paid separately)leaving an expansion gap of 3mm with necessary nails, screws etc. including 1st class local wood (Hollock /Bonsum / Sundi etc.)beading of size 50mm x 12mmcomplete as directed and specified. |
| 30 | Providing barge board of size 200mm x 20mm with 1st class local Hollock/ Bonsum timber including fitting and fixing with necessary wood screws etc. complete. |
| 31 | Providing, fitting and fixingM.S.grillof required pattern for windows/ clerestory windows/ openingwith M.S. flatsat required spacingin frame all round,squre or round M.S.bars with round headed bolts and nuts or screws.I .Plain grill(c) Fixed to Brickwork/P.C.C/R.C.C. |
| 32 | 65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) laid in panels |
| 33 | ProvidingCeramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department).A)ON FLOORNormal rangeSomany/ Orient/Nitco /Asian Make Of size 600mmx600mm and above |
| 34 | Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls).c) Delux range Somany/ Orient/Nitco/Varmora Makeii) Of size 300mmx450mm and above |
| 35 | Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor.(a) 15 mm thick |
| 36 | Providing and fixing clear sheet glass beded inputty and fixed with/without wooden bidding including necessary cutting and glass to be required sized(payment for wooden bead shall be made separately).(1) Area of glass panes not exceeding 0.15sqm(c) 3.00mm thick. |
| 37 | Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish. |
| 38 | Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified.i). 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm. |
| 39 | Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)(i) Thickness = 1.5 mm thick |
| 40 | (n) Distempering two coats with oil bound distemper of approved brand and manufacture and of required shade on new wall surface to give an even shade, over and including a priming coat with alkali resistant primer of approved brand and manufacture after throughly brooming the surface free from mortar dropings and other foreign matter and also including preparing the surface even and sand papered smooth. |
| 41 | (i) Priming coat with alkali resistant primer. |
| 42 | (ii) Top coat. |
| 43 | SPECIAL WATHER PROOF COLOURING Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats). |
| 44 | Applying priming coat over newwood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughlycleaningoil, grease, dirt snd other foreign matter , sand papering and knotting. (b). With ready mixed paint , wood primer (white). |
| 45 | Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.(i).Surfaces over 100mm in width or girth.a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac). |
| 46 | Supplying, fitting, fixing electrocoloured iron fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for wood screws including necessary screws etc. complete. |
| 47 | a) Sliding door boltsii) 250mm x 16mm |
| 48 | b) Tower bolts. iv) 150mm x 10mm |
| 49 | b) Tower bolts. v) 100mm x 10mm |
| 50 | d) MS door handles. iii) 150mm |
| 51 | Supplying, fitting and fixing chain link fencing of 10 S.W.G, G.I. Wire 50mm x50mm mesh fitted to M.S angle iron post at 2000mm apart of specification detailed below including supplying, fitting and fixing hooks, eye bolts with nuts, staples and bolts including three horizontal lines of G.I wire 10 S.W.G at top,middle and bottom and with one vertical line to each fencing post for keeping the fencing tight and erect complete, including one coat of primer painting to M.S angle iron post in P.C.C base etc. with following. a) Corner and end posts with M.S angle of size 50mmx50mmx 5mm and length not less than 1800mm only duly slotted and bottom torqued with two numbers as stay posts.. b). Intermediate post with M.S angle of size 40mmx40mmx5mm and length not less than 1800mm only duly slotted and bottom torqued and splayed. c).Stay post with M.S angle of size 35 mmx35mmx5mm and length not less than 1800mm duly slotted and bottom torqued and splayed. All M.S angle iron posts are to be fitted to P.C.C base embedded not less than 600mm (P.C.C. work shall be measured and paid separately). |
| 52 | Construction of septic tank as per drawing & analysis enclosed & as directed by the department. |
| 53 | Providingfitting and fixing vitreous water closet squatting pan (Indian type W.C Orissa pattern) with all fittings and fixtures complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately).1.1.1=Indian type W.C Orissa pattern of size 580 x 440 mm i) Parryware make |
| 54 | Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately.A) Parryware makea) White(iii) Universal Closet P Trap (Cat No.C0272) (inclusive of seat cover) |
| 55 | Supplying, fiting and fixing PVC flushing cisternwith all internal fittingswith CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately).i) Parryware make(i)Economy Single Flush (Cat No.C8090/C8055). White |
| 56 | Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISIapproved including joining ,fitting and fixing wiyh clamps etc.as necessary completeat all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. |
| 57 | (vi) 110 mm dia. |
| 58 | (vi) 50 mm dia. |
| 59 | Supplying fiting and fixing 87.5 degree PVC bendwith doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches. (ii) 110mm dia. |
| 60 | Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (v) 110mm x 50 mm |
| 61 | Providing fitting and fixing PVC cowel of ISI make completeas directed and specified.(v) 63mm dia. PVC cowel of ISI make |
| 62 | Providing vitreous Chinawash basinwith CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately).1.13.2=Basin (without (iii) Tunga Basin 450 x 300 (Cat. No.C0401)pedestal)(A) Parryware Make(a) White |
| 63 | 1.13.1. PEDESTAL BASIN (with pedestal) (ix) Cardiff 580 x 450(Cat. No.C0480/81, C0375) (white/coloured) |
| 64 | Providing fitting & fixingstainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipeetc. complete includingpainting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately.(A) Parryware Make(vi) Single Bowl (160 x 180) Flat Edge - Glossy (Cat.No.C8538) |
| 65 | Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified. |
| 66 | Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified.(a) Parryware Make(ii) Wall Soap tray (Cat. No.C9951) |
| 67 | Providing, fitting and fixing CP towel rail complete as directed and specified.(b) Sona make(iii) Towel rail Diplomat 600mm long (Cat.No.TR-0605) |
| 68 | Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately).(I) Essco make (Delux/Sumthing spl./Tropical)(b) Long body bib cock with wall flange |
| 69 | Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) (iii)Essco branda) Sink cock with "U" shape swinging castedspout |
| 70 | Supplying fitting and fixing approved P.V.C. Pipes of different sizes, with all necessary "R" brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified.(A) Exposed or in trenchesSUPREME/ PRINCE BRAND or other equvalent approved brand (High presure pipe Sch-40) |
| 71 | d) 25 mm dia |
| 72 | f) 15mm dia |
| 73 | Supplying fitting and fixing Chrome Plated (C.P.) shower 15mm dia. Of approved brand as directed and specified. (Pipes will be measured and paid separately) Jaquar make a) Continental(iii) Pressure adjustable shower with revolving joint |
| 74 | Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately).(i). (a) 15mm dia stop cock male-female/Angle stop cock (Two in One) |
| 75 | Supplying fitting & fixing health faucet of Hindware/Jaquar/Essco make as directed by the department |
| 76 | Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing "n" capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push (Anchor Penta/Gold medal /Kolor kany.Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose(Anchor/Gold medal /Kolor kany.Kom / Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt. |
| 77 | 1.1.1= Short point up to 6.00 metre. Length. |
| 78 | 1.1.2= Medium point up to 6.00 metre. Length. |
| 79 | Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mmISI marked casing "n" capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. marked)with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm.cable to third pin of the plug socket etc. as required complete, when placed elsewhere.1.2.2=Medium point up to 6.00 metre. Length. |
| 80 | Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing "n" capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including providingand fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.),GI/ MS switchboard (I.S.I. marked)with phenolic laminated sheet cover earth continuity with 2.5 sq. mmcableto the 3rd pin of the socketas required complete.1.3.2=Medium point up to 6.00 metre. Length. |
| 81 | Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface flat ISI marked casing "n" capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) system including earth continuity.1.8.1=With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm.in flat 19 mm ISI marked casing "n" capping system. |
| 82 | Supplying fixing I.C.T.P and N link Main Switch with rewire able fuses of 500 Volt grade( HPL/ GECO / ANCHOR or equivalentmake) including drilling boards/iron frames and fixing with bolts and nuts and connection as approved by the Deptt.)complete as required.12.2.1=16/20 Amps Capacity T.P.N |
| 83 | Supplying fitting and fixing industrial Plug & Socket in surface mounting SPN sheet steel powder painted MCB DB incorporated with MCB DINrail, neutral link Earth bar of the followingrating of DP MCBcomplete with making necessary connectionetc. as specified and directed by the Deptt.13.1.1=20ACapacity. (ABB, Schneider MG, legrand, Hagermake) |
| 84 | Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.16.1.1=B Series16.1.1.1=6 to 32A |
| 85 | Supplying and fitting of 18/20 Watt CFL lamp in the existing batten holder/angle holder/decorative bracket/bulk head fitting/ pendent holder etc. as specified and directed by the deptt. |
| 86 | Supplying including fitting fixing of followingA.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator].27.1.6=Standard model 1200 mm Sweep Ushamake)/ Standard model1050 / 1200 mm Sweep Havellsmake)/ High speed 1200 mm sweep (ORIENT PSPOmake). |
| 87 | Supplying including fitting fixing of followingA.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department.27.2.1.3= High Speed 225 mm sweep (ORIENTmake), Trans Air 225 mm sweep (Cromptonmake), Ventil Air DX 250 mm sweep Louver type (Havellsmake). |
| 88 | Supplying fitting and fixing of ceiling fan regulator including connections etc. complete as required.27.6.2= Electronic Type |
| 89 | Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV GSolid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1)1988 armoured U.G. cableU.G. cable laid in ground/partially in air (as required for termination over groundincluding excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris etto proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make).32.1.1=2 Core A2XWaY A2XFaY 32.1.1.2= 6.00 Sq.mm 2 Core armoured U.G. cable |
| 90 | Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 Metre long heavy duty G.I. pipewith necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mmhinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt . |
| 91 | Normal preparation of site |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
